BIOS/FW/UEFI Update for IBM N2115 SAS/SATA Controller
Controller Supported: IBM N2115 SAS/SATA Controller (46C8989)
NOTE TO SERVICE - Reference RETAIN #N/A
Version 1.20 - Non-Critical ------------- Contains: BIOS Firmware UEFI Driver 7.39.00.00 20.00.02.00 7.27.04.00 Enhancements: - Added System X agentless support - Indicate support for the ATA Device Server Password security protocol - Allow UEFI and BIOS to be Enabled/Disabled individually - Added ConnectorName and EnclosureLevel fields to SAS Device Page 0 to help identify physical location of a target device - Set SATA HOLD threshold to be configurable in NVDATA - If HW can gets into a stuck state, clear that state upon break received.
Fixes: - Set SAS drives to track bad blocks using a bad block table rather than using a SCSI Write Long. - Fixed DMAGroup performance issue. - Fixed issue with Phase 18 IR FW boot a RAID volume (such as raid 10), 2308 bootup hangs at OROM "Initializing.." and fault 8803 seen. - Fixed report Luns command to a SATA drive fails with CheckCondition/Invalid Field in CDB when Allocation length set to Zero. - Fixed issue where Raid Accelerator IOs can hang if the stream of IOs suddenly stops. - Fixed issue where an invalid frame sent during a PIO-mode SATA passthrough command results in resetting the drive. - Fixed issue where lots of NCQ I/O error messages were reported. - Fixed issue where certain PCIe timeouts occur in the presence of link unavailable, and a hang condition or data corruption can occur. - Fixed issue where system hangs after adapter reset with heavy IO load. - Fixed issue where access to Last Logical Block Address (LBA) of SATA Drive is Prevented and LBA out Of range by one block is missed. - Made change to deal with link getting stuck and causing missing drives. - Fixed IR issue where page header information is not filled in when RAID PHYS DISK PAGE 0 is returned for a non-RAID Disk drive. - Fixed issue where controller hits 0x265d fault while creating volume when there is an inactive volume. - DID_SOFT_ERRORs are seen when hot plug is performed on the RAID1 volume along with IOs. - Fixed issue where system gets hung and reboots while running IO's along with diag reset on the Controller which has active and inactive volumes. - Fixed latency spikes seen during performance testing on OEM system - MPI 2.5: distribute target command buffers received across multiple reply queues. - Fixed issue where command sas2flash -dflash results in a non-functional system. - Fixed issue where internal device reset storm after controller reset using long CDB. - Fixed 0x6003 Fault Due to Task Management of Lost IO - Fixed 0x58A1 fault occurs on partner controller while issuing MUR to a target mode controller with outstanding IOs. - Fixed issue where IO error and stop when hot plug a HDD from RAID1 - Fixed issue where fault 8901 is seen once the volume is roamed.
Fixes: - Fixed an issue where 4k sector size drives with 512e reporting enabled show wrong physical size when running a read capacity 16 command. - Fixed an issue where speed negotiation for 3Gig SATA drives is not handled properly. - Added Support for Report Luns Command - Fixed an issue where OS hang during install of Linux system to a SSD - Fixed an issue where SAS device page 0 may still be present for Initiator devices that have been removed from the topology. - Fixed an issue where RHEL 6.3 hangs during boot with IBM 600GB High IOPS MLC Modular Adapter - Fixed an issue where a non-PI volume made up of all PI capable drives, may come up as PI enabled after a controller reset. - Fixed an issue where a fault 0X8808 occurs when a reset is issued to the controller that has max number of active/inactive volumes - Fixed an issue where "Device Present" Flag of SAS device page0 is not set for initiator controller in then target controller when two controllers are connected to each other in initiator/target mode. - Fixed an issue where extended tags and PCIe upconfigure capability are disabled in SAS2208 and SAS2308. - Fixed an issue where force full discovery does not trigger rediscovery of an expander after the initial expander discovery fails. - Fixed an issue where single RAID0 volume activation was succeeding, even though controller does not support single drive RAID0. - Fixed an issue where RAID1 volume of Non-PI drives moves to optimal state when a PI drive is hotplugged and 'Enable PI mixing' not enabled. - Fixed an issue where Locate LED's stop automatically after 3-4 minutes before user issues command to turn off the Locate LED's. - Fixed an issue where fault 0x8618 is seen when a new volume is created in the presence of another volume which is undergoing resync along with IO. - Fixed an issue background initialization does not start on RAID0 volume with PI drives, after removing and reinserting a volume member.
BIOS - Fixed an issue where core BIOS displays warning message when it fails to add all of the drives connected to int13 chain, then waits for user to press any key to continue further, rather than continuing after 3 seconds. - Fixed an issue where incorrect adapter is being tagged as the first adapter found. - Fixed an issue where the save or discard changes prompt appears after a failed attempt to set volume as the boot device in BIOS CU. - Fixed an issue where BIOS CU provides incorrect device pointer when checking for raid disk to allow/disallow setting boot device. - Fixed an issue where device properties screen is invoked from a direct attach device using Alt+D in SAS topology screen, device traversing [Alt+N & Alt+P] is restricted within the direct attach device and expander attach devices are not traversed. - Fixed an issue where the drive status field does not show 'Max dsks' when trying to select 11th drive for RAID10 volume. - Fixed an issue maximum Int13 devices settings does not get honored, when the value is set as 0 in BIOS CU - Fixed an issue where drive size of 1.088GiB was showing as 1.880GiB. - Fixed an issue current boot device set to device at slot 4" message Not displaying for Adaptors with boot order other than 0. - Fixed an issue where the BIOS CU navigates to create new volume screen instead of back to raid properties screen. - Fixed an issue where BIOS banner showed 'FF' for slot information. - Fixed an issue where the drive's SMART status is always shown as no irrespective of drive's SMART status, under Pred Fail column of the manage hot spare screen and create new volume screen. - Fixed an issue where SAS2 BIOS: volume size shows inconsistent value in the create new volume' screen after selecting the last volume member. - Fixed an issue where a disabled adapter causes the second adapter status to show as unavailable even though the second adapter is enabled. Uefi Enhancement 1/2 - Added capability to create an IR RAID volume in non-PI mode, even when all member drives are PI Capable. - Added PI info and ability to control creation of PI Volume in UCM of BSD HII. - Added new form manage PHY settings to support enabling or disabling of a controller PH Fixes: - Fixed an issue view foreign volume option is disabled with a foreign volume in the configuration.
BIOS/FW/UEFI Update for IBM N2125 SAS/SATA Controller
Controller Supported: IBM N2125 SAS/SATA Controller (46C9011)
NOTE TO SERVICE - Reference RETAIN #N/A
Version 1.20 - Non-Critical ------------- Contains: BIOS Firmware UEFI Driver 7.39.00.00 20.00.02.00 7.27.04.00 Enhancements: - Added System X agentless support - Indicate support for the ATA Device Server Password security protocol - Allow UEFI and BIOS to be Enabled/Disabled individually - Added ConnectorName and EnclosureLevel fields to SAS Device Page 0 to help identify physical location of a target device - Set SATA HOLD threshold to be configurable in NVDATA - If HW can gets into a stuck state, clear that state upon break received.
Fixes: - Set SAS drives to track bad blocks using a bad block table rather than using a SCSI Write Long. - Fixed DMAGroup performance issue. - Fixed issue with Phase 18 IR FW boot a RAID volume (such as raid 10), 2308 bootup hangs at OROM "Initializing.." and fault 8803 seen. - Fixed report Luns command to a SATA drive fails with CheckCondition/Invalid Field in CDB when Allocation length set to Zero. - Fixed issue where Raid Accelerator IOs can hang if the stream of IOs suddenly stops. - Fixed issue where an invalid frame sent during a PIO-mode SATA passthrough command results in resetting the drive. - Fixed issue where lots of NCQ I/O error messages were reported. - Fixed issue where certain PCIe timeouts occur in the presence of link unavailable, and a hang condition or data corruption can occur. - Fixed issue where system hangs after adapter reset with heavy IO load. - Fixed issue where access to Last Logical Block Address (LBA) of SATA Drive is Prevented and LBA out Of range by one block is missed. - Made change to deal with link getting stuck and causing missing drives. - Fixed IR issue where page header information is not filled in when RAID PHYS DISK PAGE 0 is returned for a non-RAID Disk drive. - Fixed issue where controller hits 0x265d fault while creating volume when there is an inactive volume. - DID_SOFT_ERRORs are seen when hot plug is performed on the RAID1 volume along with IOs. - Fixed issue where system gets hung and reboots while running IO's along with diag reset on the Controller which has active and inactive volumes. - Fixed latency spikes seen during performance testing on OEM system - MPI 2.5: distribute target command buffers received across multiple reply queues. - Fixed issue where command sas2flash -dflash results in a non-functional system. - Fixed issue where internal device reset storm after controller reset using long CDB. - Fixed 0x6003 Fault Due to Task Management of Lost IO - Fixed 0x58A1 fault occurs on partner controller while issuing MUR to a target mode controller with outstanding IOs. - Fixed issue where IO error and stop when hot plug a HDD from RAID1 - Fixed issue where fault 8901 is seen once the volume is roamed.
Enhancement - Reduce the boot time for UEFI driver for large configurations Fixes: - Fixed an issue that caused the Integrated Management Module (iMM) in System x servers to report Warning: Sensor GPT Status has transitioned from normal to non-critical state. - Fixed an issue where 4k sector size drives with 512e reporting enabled show wrong physical size when running a read capacity 16 command. - Fixed an issue where speed negotiation for 3Gig SATA drives is not handled properly. - Added Support for Report Luns Command - Fixed an issue where OS hang during install of Linux system to a SSD - Fixed an issue where SAS device page 0 may still be present for Initiator devices that have been removed from the topology. - Fixed an issue where RHEL 6.3 hangs during boot with IBM 600GB High IOPS MLC Modular Adapter - Fixed an issue where a non-PI volume made up of all PI capable drives, may come up as PI enabled after a controller reset. - Fixed an issue where a fault 0X8808 occurs when a reset is issued to the controller that has max number of active/inactive volumes - Fixed an issue where "Device Present" Flag of SAS device page0 is not set for initiator controller in then target controller when two controllers are connected to each other in initiator/target mode. - Fixed an issue where extended tags and PCIe upconfigure capability are disabled in SAS2208 and SAS2308. - Fixed an issue where force full discovery does not trigger rediscovery of an expander after the initial expander discovery fails. - Fixed an issue where single RAID0 volume activation was succeeding, even though controller does not support single drive RAID0. - Fixed an issue where RAID1 volume of Non-PI drives moves to optimal state when a PI drive is hotplugged and 'Enable PI mixing' not enabled. - Fixed an issue where Locate LED's stop automatically after 3-4 minutes before user issues command to turn off the Locate LED's. - Fixed an issue where fault 0x8618 is seen when a new volume is created in the presence of another volume which is undergoing resync along with IO. - Fixed an issue background initialization does not start on RAID0 volume with PI drives, after removing and reinserting a volume member.
BIOS - Fixed an issue where core BIOS displays warning message when it fails to add all of the drives connected to int13 chain, then waits for user to press any key to continue further, rather than continuing after 3 seconds. - Fixed an issue where incorrect adapter is being tagged as the first adapter found. - Fixed an issue where the save or discard changes prompt appears after a failed attempt to set volume as the boot device in BIOS CU. - Fixed an issue where BIOS CU provides incorrect device pointer when checking for raid disk to allow/disallow setting boot device. - Fixed an issue where device properties screen is invoked from a direct attach device using Alt+D in SAS topology screen, device traversing [Alt+N & Alt+P] is restricted within the direct attach device and expander attach devices are not traversed. - Fixed an issue where the drive status field does not show 'Max dsks' when trying to select 11th drive for RAID10 volume. - Fixed an issue maximum Int13 devices settings does not get honored, when the value is set as 0 in BIOS CU - Fixed an issue where drive size of 1.088GiB was showing as 1.880GiB. - Fixed an issue current boot device set to device at slot 4" message Not displaying for Adaptors with boot order other than 0. - Fixed an issue where the BIOS CU navigates to create new volume screen instead of back to raid properties screen. - Fixed an issue where BIOS banner showed 'FF' for slot information. - Fixed an issue where the drive's SMART status is always shown as no irrespective of drive's SMART status, under Pred Fail column of the manage hot spare screen and create new volume screen. - Fixed an issue where SAS2 BIOS: volume size shows inconsistent value in the create new volume' screen after selecting the last volume member. - Fixed an issue where a disabled adapter causes the second adapter status to show as unavailable even though the second adapter is enabled. Uefi Enhancement 1/2 - Added capability to create an IR RAID volume in non-PI mode, even when all member drives are PI Capable. - Added PI info and ability to control creation of PI Volume in UCM of BSD HII. - Added new form manage PHY settings to support enabling or disabling of a controller PH Fixes: - Fixed an issue view foreign volume option is disabled with a foreign volume in the configuration.
Version 12.15.0-0240 - Moderate Impact/Low Probability of Occurrence --------------------- Fixes: - Fixed issue where JBOD mode would be disabled and would not boot to JBOD drive if one of the VDs is offline (SCGCQ00827731) - Fixed illegal request sense messages seen repeatedly in FW logs. (SCGCQ00898459) - Fixed system hangs that could occur due to recoverable errors being marked as unrecoverable (SCGCQ00923692)
Version 12.15.0-0226 ---------------
- Fixed an issue where JBOD drives were not reporting the correct drive temperature (SCGCQ00831639) - Corrected LED behaviour for IBM 6Gb SAS Expander Backplane (SCGCQ00754433)
Version 12.15.0-0199 - Critical ------------------- Enhancement: - Display drive speed for 12 GB Seagate hard drives in MSM. - List battery status in BIOS as N/A for iMR controllers Fixes: - Fixed an issue where the ‘cli set securitykey=Lsi@12345’ command fails with error code 1001 and error message invalid key. - Fixed an issue where WebBIOS is not displaying correct index position for boot error handling option. - Fixed an issue where WebBIOS advanced software option locks the server.
Version 12.13.0-0179 - Critical ------------------- Enhancement: - Implemented limited band charging for iBBU08. (RETAIN tip H21631) - CacheCade 2.0 read and write caching on SSDs is supported on ServeRAID M5014 and ServeRAID M5015 with the ServeRAID M5000 Series Performance Accelerator Key. Fixes - Fixed an issue in multipath topology to use an alternate IO path if the current active path is removed. - Fixed an issue where drive states were marked as online before the creation of recontruction volumes completed. - Resolved controller hang condition during system bootup. - Fixed issue causing iBBU07 to always show "Charging" state (RETAIN tip H211025) - Fixed issue causing Virtual Disks to remain in Write-Through state after a relearn (RETAIN tip H211101) - Addressed data exposure issue when using CacheCade
Version 12.12.0-0133 - Suggested ------------------- Fixes: - Addressed an issue where battery over temperature messages could occur during charging. - Fixed issue in the HII broswer where the drive performing copyback will be stated as replacing and not copyback. - Fixed issue in the HII browser where the RPM for SATA drives show "0" - Fixed issue in HII browers where port 4 is shown on both ports 0 and 1 - Fixed HII browser issue where the user will get an error message when a global hot spare is created. - Fix HII browser issue where a RAID volume with greater then 3 spans will fail to create.
Version 12.12.0-0126 - Critical ------------------- Fixes: - Fixed a issue where the RAID configuration can be lost when updating from firmware package 12.0.1-0097 or below. - Fixed an issue with 4-kilobyte (KB) sector disk support compatibility in NTFS by disabling 512E drive support mode.
Version 12.12.0-0111 - Suggested ------------------- Enhancement: - Support for 512e and 4k SAS/SATA hard drives added - Implemented limited band charging for iBBU 07. - CacheCade 2.0 read and write caching on SSDs is supported on ServeRAID M5014 and ServeRAID M5015 with the ServeRAID M5000 Series Performance Accelerator Key. Fixes: - Set the compatibility bit to 1 so that Patrol reads can be executed on SSD's - Fixed an issue where EEPROM init failures are not handled properly causing the user to see the following message on POST "The native configuration is no longer supported by the current controller and firmware." - Fixed an issue where the controller fails to read the header info from CFI Flash ROM. - Resolved issue switching to WT mode for recently failed batteries.
Version 12.12.0-0098 - Suggested ------------------- Fixes: - Fixed issue where the battery gauge is not accurate for aged batteries due to the discharge profiles of aged batteries not matching that of the new batteries. - Fixed a issue where a reboot would cause a hot spare to revert to 'Unconfigured Good' state when Performance Accelerator Key is attached. (RETAIN Tip H204925)
Version 12.12.0-0085 - Suggested ------------------- Enhancements: - Prevent non IBM firmware from being flashed on IBM ServeRAID branded controllers. - Enabled iBBU08 battery modes. - ibbu battery will no longer be marked as bad when very high capacity is detected. - Dimmer Switch function has been disabled by default.
Fixes: - Fixed a issue where firmware was taking to long to complete the PCI config read, causing the system to generate an NMI. - Fixed issue where enabling security causes the configuration to be missing, and a configured FDE array to be seen as foreign on reboot. - Removed BBU mode select from Web BIOS for all controllers. - Fixed issue where pulling VD 0 from a R60 and rebooting would cause two foreign configurations. - Fixed issue where WebBIOS gives unclear message when enabling FDE on an existing Disk Group. - Fixed issue where iBBU07 batteries display 65K capacity and are marked SOH bad. - Fixed issue where iBBU Absolute Charge is displayed differently - Fixed issue where the logical Unit ID (VPD page 0x83) changed after foreign import. - Fixed issue where the LDBBM entries are incorrect after foreign import. - Fixed issue where the controller does not work with pci set to nomsi in kdump kernel. - Fixed issue where the LED behavior is incorrect, wrong drive will blink activity. - Fixed issue where the controller cannot sustain at least 950 MBps performance with Cache Flush setting one sec. - Fixed issue where the set properties command fails - Fixed issue where the iBBU07 battery reported remaining capacity is much too high (64751 mAh) after a learn cycle. - Fixed issue where extended retries of write verify commands cause a driver timeout. - Fixed issue where the configuration becomes foreign after the firmware fails multiple attempts to access raid key during boot. - Fixed firmware issue where a replacement drive is not seen if the replacement is added during power cycle. - Fixed a issue where an alert should be sent when one phy connector between the SAS controller and SAS expander is degraded. - Enabled puncturing for SATA drives. - Enabled copy back on SMART. - Fixed an intermittent RAID key failure during power-on. - Fixed firmware issue where firmware would cause the controller to (sles11sp1/rhel6) reset when ‘lspci –vvx’ command is executed. - Change for iBBU-08 to support firmware Mode5 WB capacity from 960mAh to 674mAh for low power DDR-2 - Fixed a issue where the iBBU battery will not charge while the server continually resets causing the iBBU battery to over-charge.
Version 12.12.0-0065 - Critical ------------------- Fixes: - Fixed issue where the firmware takes too long to complete a PCI Config Read cycle causing SLES11 to kernel panic. - Fixed issue where MegaCLI may not be able to change drive or controller cache setting resulting in a return code of 0x03. - Added check to return SCSI sense Check condition if PMI is set and LBA is non Zero for SCSI Read Cap 16 - Fixed issue where a blue screen occurs handling RAID 1 with HSP and medium errors. The blue screen occurs because the driver times out while the firmware is retrying sense 0x02. Firmware causes Fatal Error when HSP drive responded with Sense 0x02 for Write/Verify or TUR - Change the boot with pinned cache RAID level support which was only allowed for raid level 0. The check is removed and is allowed for any raid level. - Fixed hang condition or condition where the uEFI driver does not load due to the uEFI Driver issuing a command in poll mode to firmware to early - Remove the following message "Battery cannot initiate transparent learn cycles" when the iBBU08 is under mode 4 or 5 - Fixed issue where BGI will not disable when a user issues megacli -LDBI -Dsbl -L0 -a0
Version 12.12.0-0056 - Critical ------------------- Fixes - Fixed issue where multi-bit ECC's are not reported during POST - Lowered the capacity level at which event notifications are generated for early warning and end of life alerts for iBBU to equal 48 hours
Version 12.12.0-0047 - Critical ------------------- Fixes: - Fixed issue where uEFI WebBIOS version may not display the product name of the second controller - Fixed issue to prevent users from downleveling firmware to older versions - Fixed an issue where firmware reports "Unexpected sense, Invalid field in CDB" for LOG SENSE command sent to Seagate drives - Fixed issue where SMART failures can take longer then 5 minutes to report or in some cases fail to report - Fixed issue where it appears to the user the harddrive cache policy is changed when requested but the change did not occur - Fixed issue where a remote iBBU08 will not be seen by the controller - Fixed data issue When IO is in progress to a RAID 1 array that contains media errors and is under a rebuild - Fixed issue where a drive is not marked as foreign during a drive move between servers causing the import of the configuration to fail - Fixed issue where the uEFI WebBIOS does not accept the + symbol in the key code or pass phrase - Fixed issue for iBBU08
Enhancement: - Enhancement to Reserve/release call for VCS Symantec configurations - Enhancements to iBBU event notifications, including the addition of early warning message. - Raised the capacity level at which event notifications are generated for early warning and end of life alerts for iBBUs.
Version 12.12.0-0039 - Critical ------------------- Fixes: - Fixed intermittent initialization failure during POST with the ServeRAID M5025, M5015, and M5014 where the RAID BIOS could fail to load or the user will see one of the following error messages on POST:
RAID Adapter Unrecoverable Error!!! Please check the SDRAM connection.
or
Multi-bit ECC errors were detected on the RAID controller
Version 12.12.0-0037 - Critical ------------------- Enhancement: - Add support for iBBU08 (Battery Backup)
Fixes: - Addressed data issue while reconstructing from RAID1 to RAID0. - Addressed data issue after power lose to ServeRAID controllers. - Addressed data issue in some database applications. - Added fixes from LSI channel products.
Version 12.7.0-0020 - Critical ------------------- Enhancement: - Initial release for ServeRAID M5025 SAS/SATA Controller (46M0830)
Fixes: - Addressed data issue with database applications that use overlapping read write operating. - Addressed data issue which may occur during a reconstruction on some RAID levels that have an associated CacheCade virtual drive enabled. - Fixed issue where the controller may halt if a drive has medium errors that are being used in a check consistency, patrol read, or have delayed writes.
Version 12.0.1-0097 - Critical ------------------- Fixes: - Addresses an issue where data becomes inaccessible when drive is secured after data has been written . Version 12.0.1-0096 - Critical ------------------- Fixes: - Fixed an issue where the BBU may not be seen on POST. - Fixed an issue where the firmware doesn't follow the spinupdelay and maxtargetspinup values set in NVDATA causing spin up of all the drives a at the same time. - Fixed a very intermittent issue where the RAID key (M5000) authentication may not occur on boot leaving users without key options. - Addressed a very rare issue with the expander devices where the firmware megamon could occur if the sgpio configuration cable has errors.
Version 12.0.1-0090 - critical ------------------- Fixes: - Fixed issue where controller properties such as Rebuild, CC, and BGI are not changing when up and down arrow keys are used. - Fixed issue on x3950 M3 servers that can cause a system hang at reboot
Version 12.0.1-0084 - Non-critical ------------------- Enhancement: - Support added for the ServeRAID M5000 Series Advanced Feature Key.
Version 12.0.1-0064 ------------------- - Initial release ibm_fw_sraidmr_m5000-12_15_0-0248_linux_32-64_chg
ServeRAID M1000 Series SAS/SATA Controller Firmware Update
Adapters Supported: ServeRAID M1115 SAS/SATA Controller for IBM System X (81Y4448) ServeRAID M1015 SAS/SATA Controller (46M0831)
Version 20.13.1-0254 --------------------
Version 20.13.1-0252 - Moderate Impact/Low Probability of Occurrence --------------------- Fixes: Fixed issue where wrong drive connector information (connector: null x0) shows in MSM (SCGCQ00996578) Fixed issue where firmware hit assertion while booting with 4K PDs. (SCGCQ00944388) Fixed system hangs that could occur due to recoverable errors being marked as unrecoverable (SCGCQ00923692) Fixed issue where exception would occur during foreign import while importing number of VDs greater than supported count (SCGCQ00931011)
Version 20.13.1-0245 - Moderate Impact/Low Probability of Occurrence --------------------- - Fixed an issue where virtual drivers become inconsistent after the system an AC failure. (SCGCQ00897229) - Fixed an issue where Illegal request sense messages are seen repeatedly in FW logs due to attempts to collect temperaure for pds which does not support page (0x2F) at every smart poll interval. (SCGCQ00898459) - Fixed an issue where command "cli set securitykey=Lsi@12345" fails with error code "1001" and error message "invalid key". - Added a warning message when preboot configuration utility is Disabled but the user tries to launch it. (SCGCQ00662761) - Fixed an issue where WebBIOS Advance software option menu from main page could hang the system. (SCGCQ00683327) - Updated the drive speed display string to support 12Gb/s (SCGCQ00751036) - Corrected inconsistency in size showing in for total capacity property between webBIOS and MSM (SCGCQ00752176)
Version 20.13.1-0200 - Critical ------------------- Enhancement: - Display drive speed for 12 GB Seagate hard drives in MSM. - List battery status in BIOS as N/A for iMR controllers Fixes: - Fixed an issue where the ‘cli set securitykey=Lsi@12345’ command fails with error code 1001 and error message invalid key. - Fixed an issue where WebBIOS advanced software option locks the server. - Changed patrol read completion time calculation to include time for associated IO operations. - Fixed SGPIOs signal issue.
Version 20.11.1-0184 - Suggested ------------------- Fixes: - Updated SBR to avoid an errata that could cause correctable CPU errors on some systems. - Fixed an issue where NULL events may show in event log, preventing capture of controller event logs.
Version 20.11.1-0137 - Suggested ------------------- Enhancement(s): - Update recovery mode page (WriteRetryCount and recoveryTimeLimit) during discovery of a drive and during spinup recovery when sense 6/29 is received.
Fixes: - Fixed an issue where certain drives were reporting a temperature of 65 degrees Celsius. - Fixed an issue where systems with SSD HDD will pop up an error message after creating a virtual drive via HII on M1115. - Fixed an issue where the drive state is not modified when a recon virtual drive is created from the reboot path.
Version 20.10.1-0107 - Suggested ------------------- Fixes: - Fixed grammatical errors in WebBIOS. - Fixed an issue in WebBIOS Drive Group Definition screen where enclosures should not be selectable in the Drives column. - Fixed an issue in uEFI-WebBIOS where the white bars do not match up under VD properties page. - Fixed an HII browser issue where a drive performing a copyback displayed the state as "Replacing" but other utilities showed the state as copyback. - Fixed an HII browser display issue where SATA drives showed "0" for the value of RPM under drive properties. - Fixed a display issue where the HDD port number showed incorrectly in an HII browser. - Fixed an HII browser issues where creating a global hotspare gave the user an error message. - Fixed an HII browser issue when security is changed with local key management the changing security report current mode is disabled as external keu management. - Fixed an HII browser issue where the user got the following error message, "The request command has invalid arguments," when changing the security key report. - Fixed an HII browser issue where the user was unable to save the configuration after adding an extra span during array creation. - Fixed an HII browser issue where the return value was not correct when the browser called extract config with a result of null.
Version 20.10.1-0101 - Suggested ------------------- Fixes: - Fixed an issue where a system uefi error will occur when the bootTargetId is set to 0. - Fixed a problem where the firmware will allocate the sata bbl entry for the drive when moved from unsupported to supported. - Fixed a firmware issue where the TargetId for the recon LD should be set to its original LD. - Fixed a HII error message "Question Value mismatch with Option value!" after selecting factory defaults in HII. - Fixed an issue where the firmware fails to create the configuration and utilities fail to report the VD size after the reconstruction.
Version 20.10.1-0091-01 - Non-Critical ------------------- Fix - Fixed issue where update may fail to find all supported controllers in SLES 11 SP 2. Note not change in the firmware; it is the same as package 20.10.1-0091.
Version 20.10.1-0091 - Suggested ------------------- Enhancement: - Add support for ServeRAID M1115
Fixes: - Fixed issue where after starting a reconstruction on a RAID 0 the progress %, does not increase. - Fixed an issue where a new drive, inserted after a drive failure, goes to JBOD and not auto rebuild. - Fixed physical drive count issue that stated more than (16) devices already exists
Version 20.10.1-0069- Suggested ------------------- Enhancement: - ServeRAID M1015 Dimmer Switches are disabled by default.
Fixes: - Fixed issue where enabling security causes the configuration to be missing, and a configured FDE array to be seen as foreign on reboot. - Fixed issue where WebBIOS gives garbled message when enabing FDE on an existing Disk Group - Fixed issue where the logical Unit ID (VPD page 0x83) changed after foreign import. - Fixed issue where the LDBBM entries are incorrect after foreign import. - Fixed a problem where firmware was taking to long to complete the PCI config read. Causing the system to generate an NMI. - Fixed issue where the controller does not work with pci set to nomsi in kdump kernel. - Fixed issue where the LED behavior is incorrect, wrong drive will blink activity. - Fixed issue where the configuration becomes foreign after the firmware fails multiple attempts to access raid key during boot. - Fixed firmware issue where a replacement drive is not seen if the replacement is added during power cycle. - Fixed an intermittent RAID key failure during power-on.
Version 20.10.1-0052- Critical ------------------- Enhancement: - Add support to pass SMART errors for JBOD drives to MSM
Fixes: - Added check to return SCSI sense Check condition if PMI is set and LBA is non zero for SCSI Read Cap 16. - Fixed issue where a bluescreen occurs handling RAID 1 with HSP and medium errors. The bluescreen occurs becausethe driver timesout while fw is retrying sense 0x02. Firmware causes Fatal Error when HSP drive responded with Sense 0x02 for Write/Verify or TUR - Fixed hang condition or condition where the uEFI driver does not load due to the uEFI Driver issuing a command in poll mode to firmware to early
Version 20.10.1-0045 - Critical ------------------- Fix: - Fixed issue where firmware has incomplete writes during power fail and recovery
Version 20.10.1-0036 - Critical ------------------- Fixes: - Fixed issue where uEFI WebBIOS version may not display the product name of the second controller - Fixed issue to prevent users to downlevel firmware to older versions - Fixed an issue where firmware reports "Unexpected sense, Invalid field in CDB" for LOG SENSE command sent to Seagate drives - Fixed issue where SMART failures can take longer then 5 minutes to report or in some cases fail to report - Fixed issue where it appears to the user the harddrive cache policy is changed when requested but the change did not occur
Version 20.10.1-0022 - Critical ------------------- - Fixed issue where Windows 2008 R2 WS08 cannot be installed properly on ServeRAID M1015 SATA JBOD with a uEFI boot. - Added warning message when user tried to change more then 16 drives to JBOD. - Addressed a problem where direct attached drives are given incorrect slot numbers - Added fixes from LSI channel products. - Fixed issue where a single JBOD drive will not boot after a Windows 2008 R2 installation.
Version 20.5.1-0014 - Critical ------------------- - Addressed data issue with database applications that use overlapping read write operating. - Addressed data issue which may occur during a reconstruction on some RAID levels that have an associated CacheCade virtual drive enabled. - Fixed problem where the controller may halt if a drive has medium errors that are being used in a check consistency, patrol read, or have delayed writes.
Version 20.1.1-0059 - Critical ------------------- Fixes: - Fixed an issue where a physical drive that is changed to JBOD from powersave will become unconfigured good again - Addresses an issue where data becomes inaccessible when a drive is secured after data has been written
Version 20.1.1-0049 - Suggested ------------------- Enhancement - Support M1000 key for RAID 5 and SED support
Fixes: - Fixed an issue in M3950M3 where webbios would hang - Fixed an issue where the controller properties in WebBIOS such as Rebuild, CC and BGI are not changing when we use up and down arrow keys. - Fixed an issue where Enclosure ID's are not being shown in MSM
Version 20.1.1-0046 - Suggested ------------------- - Enabled support for the ServeRAID M1000 Series Advanced Feature Key.
Note: All Logical Drives must previously have the encryption enabled before data is written on to the SED drives. Please read Retain TIP H123152 for more details.
Version 20.1.1-0042 ------------------- - Initial release ibm_fw_sraidmr_1000-20_13_1-0254_linux_32-64_chg
ServeRAID 6GB SAS/SATA Controller Firmware Update
Adapters Supported: ServeRAID M5110 SAS/SATA Controller for IBM System x (81Y4481) ServeRAID M5110e SAS/SATA Controller for IBM System x ServeRAID M5120 SAS/SATA Controller for IBM System x (81Y4478) ServeRAID M5016 SAS/SATA Controller for IBM System x (90Y4304) ServeRAID M5115 SAS/SATA Controller for IBM Flex System (90Y4390) ServeRAID M5016 SAS/SATA Controller for IBM System x (90Y4304)
NOTE TO SERVICE - Reference RETAIN #N/A
Version 23.34.0-0018 --------------------
Version 23.34.0-0009 - High Impact/High Probability of Occurrence -------------------- FW Package: 23.24.0-0009
HII: 03.17.14.02
UEFI Driver: 0x06110200
BIOS: 5.50.03.0
MR FW: 3.460.35-6104
iMR FW: 3.460.34-6103
Fixes:
- Fixed the potential of a data miscompare that was observed only at a vendor test facility under very heavy IO and abnormal practices (SCGCQ00995594, Port of SCGCQ00976904)
- Fixed an issue where error "Controller encountered fatal error and was reset" may occur under heavy IO and background operations (SCGCQ00894643)
- Fixed an issue where VMWare may crash when a Guest Operating System is powered off (SCGCQ00872121, Port of SCGCQ00854914)
- Fixed an issue where write-verify performance was lower than expected (SCGCQ00858151, SCGCQ00874193)
- Fixed an issue where "I2C 4 PID 10 SCL STUCK Low! while I2C Rx receiving data intStatus 00008000" may appear in firmware log (SCGCQ01007592)
- Fixed an issue where the Measured Voltage instead of Charging Voltage was displayed in event log (SCGCQ00876489)
- Fixed an issue where Supercap "Battery Not Present" error may occur after shutdown or reboot during a learn cycle (SCGCQ00917115)
- Fixed an issue where Write-through and Write-back cache policies can be changed via Windows Logical Disk Properties. (SCGCQ00856979)
- Fixed an issue where enclosures may go missing when connected in daisy-chain after multiple expander reset cycles (SCGCQ00840725, Port of SCGCQ00818569)
- Fixed an issue where MegaRAID Storage Mananger may display an error message if 'Schedule Consistency Check' is selected. (SCGCQ00852649, Port of SCGCQ00832908)
- Fixed an issue where Patrol Read Properties window does not pop up on MegaRAID Storage Manager (SCGCQ00862478, Port of SCGCQ00797676)
- Fixed an issue where MegaRAID Storage Manager shows messages with Error code 240 and no description (SCGCQ00970948, Port of SCGCQ00904466)
- Fixed an issue where Amber LED may turn on erroneously when an enclosure's slot numbers start with 0 but bay numbers start with 1 (SCGCQ01019622, Port of SCGCQ00903181)
- Fixed an issue where the Generic RAID1 profile option in HII is not greyed-out after creating 64 Virtual Drives (SCGCQ00826822, Port of SCGCQ00816137)
- Fixed an issue where firmware may hang until system is reset (SCGCQ00928869, Port of SCGCQ00923286)
- Fixed an issue where a Virtual Drive may disappear on reboot if it was created with drives from a previously-erased Virtual Drive (SCGCQ00937912, Port of SCGCQ00900237)
- Fixed an issue where Functional Level Reset was not supported (SCGCQ00854343, Port of SCGCQ00840253)
- Fixed an issue where an "L2 unrecoverable cache error" may occur when modifying Patrol read properties (SCGCQ00854668, Port of SCGCQ00847162)
- Fixed an issue where a Hot Spare disk may become Unconfigured Good on reboot (SCGCQ00862477, Port of SCGCQ00803341)
- Fixed an issue where SafeID may change on repeated queries using StorCLI (SCGCQ00949550, Port of SCGCQ00941577)
- Fixed an issue where error "MonTask: line 1272 in file ../../raid/1078dma.c" may occur while running IO in Virtual Machines (SCGCQ01016071, Port of SCGCQ00822403)
- Fixed an issue where incorrect connector information "connector: null x0" shows in MegaRAID Storage Manager (SCGCQ01016040, Port of SCGCQ00996578)
- Fixed an issue where a concurrent Consistency Check cannot be started after resetting adapter to factory defaults (SCGCQ00839437, Port of SCGCQ00838830)
- Fixed an issue where JBOD mode may be disabled if a Virtual Drives is offline (SCGCQ00871662, Port of SCGCQ00827731)
Enhancements:
- Added protection for clearing Foreign Configuration if preserved cache exists (SCGCQ00880783, Port of SCGCQ00842327)
- Enhanced cache restore operation for when restore data size is different than cache size (SCGCQ00860303, Port of SCGCQ00855038)
Version 23.33.0-0044 --------------------
Version 23.33.0-0043 - High Impact/High Probability of Occurrence ----------- Fixes: - Fixed an issue where hard drive slot amber LED not functioning correctly. - Fixed an issue in iMR mode where "Controller encountered fatal error and was reset" errors can occur under heavy IOs and background operations (SCGCQ00894643) (RETAIN Tip H001154) - Fixed an issue where BBU status says optimal but firmware logs indicate that the BBU has failed (SCGCQ00838052) (RETAIN Tip H214857) - Fixed an issue where importing a foreign configuration may fail after reconstruction on 4k sector drives (SCGCQ00830109) - Fixed an issue where the firmware may allow the OS to change VD cache settings (SCGCQ00842350) - Fixed an issue where MR firmware reports "no SMART" error when attaching a PFA drive (SCGCQ00839455) - Fixed an issue where the firmware may hang (enter MonTask) when a guest OS is powered on or off in VMWare (SCGCQ00854914) - Fixed an issue where setting the learn cycle property of iBBU09 gives an I2C error (SCGCQ00831315) - Fixed an issue where "Prepare for Removal" does not work on a PD when drive erase is in progress (SCGCQ00811219) - Fixed an issue where MSM displays "The requested command has invalid arguments" error message if 'Schedule Consistency Check' is selected (SCGCQ00852649) - Fixed an issue where cache memory size in iMR is not showing 0 (SCGCQ00838893) - Fixed an issue where an incorrect MFI_STAT_PD_TYPE_WRONG error is returned by the firmware when PDs with different block size are mixed (SCGCQ00840251) - Fixed an issue where the controller reports cache memory size as 0 when no logical drives are present (SCGCQ00837600) - Fixed an issue where concurrent consistency check cannot be started after issuing "setfactorydefaults" command (SCGCQ00839437) - Fixed an issue where uEFI may report LSI EFI driver "Unhealthy" or "Failed" when more than 64VDs are configured (SCGCQ00831006) - Fixed an issue where functional level reset was not properly showing as unsupported (SCGCQ00854343) - Fixed an issue where the legacy CTRL-H utility may report the wrong PCIe slot number (SCGCQ00799339) - Fixed an issue where the legacy OpROM may show an expander as a JBOD drive in POST (SCGCQ00809682) - Fixed an issue where an encrypted JBOD may be presented to the system in encrypted form even though password was entered incorrectly (SCGCQ00808086)
Enhancements: - Added ability to determine SuperCap revision ID when VPD is not programmed (SCGCQ00828990) - Added support for SES RQST_OK deassertion for customer proprietary JBOD SEP (SCGCQ00834321) - Added feature to enable support for detecting CPLD code version (SCGCQ00840631) - Added feature to enable drive fault LED to be lit when a known-bad drive is connected to the controller (SCGCQ00858142) - Added feature to turn on drive Fault LED when the controller detects a drive that was previously marked Bad (SCGCQ00858140)
Version 23.33.0-0018 - High Impact/High Probability of Occurrence ----------- Fixes: - Incorporated MegaRAID FW stack 5.13 - Fixed an issue where drive temperature cannot be displayed for a drive in Failed or Foreign state (SCGCQ00693959) - Fixed an issue where after creating an LD via StorCLI or MSM the firmware writes into saved power condition mode page (0x1a) of all PDs in the LD and enables their idle timers (SCGCQ00658701) - Fixed an issue where Patrol Read would sporadically correct the same defective LBA repeatedly (SCGCQ00729591) - Fixed an issue where importing a Foreign array onto a new controller may fail with "Cannot force emulate VD to 512E since enable512Esupport is false" error in firmware log (SCGCQ00721106) - Fixed an issue where the controller may enter MegaMon sporadically (SCGCQ00776409) - Fixed an issue where MSM may not report a Full Initialization Aborted error until system rebooted (SCGCQ00759100) - Fixed an issue where the firmware may allow the OS to change VD cache settings (SCGCQ00842350) - Fixed an issue where Link Speed may show UNKNOWN when attaching a 3G or 6G SATA drive (SCGCQ00803522) - Fixed an issue where StorLib may return 0x00ff (fail) code even though operation succeeds when creating a VD out of an existing drive group (SCGCQ00827685) - Fixed an issue where format process of SSD may take much longer than in previous firmware (SCGCQ00674388) - Fixed an issue where controller must have cleared config to enable 240VD unless existing config only included single-drive RAID0 VDs (SCGCQ00559643) - Fixed an issue where some commands would timeout with CDB=ff ff ff ff (SCGCQ00459760) - Fixed an issue where slot ordering in iMR mode might differ from slot numbering in MR mode (SCGCQ00559274) - Blocked CacheCade deletion when multiple CacheCade volumes are associated with Virtual Drives, preventing data issues (SCGCQ00830977) (RETAIN TIP H214323)
Features/enhancements: - Added support for 512e drives (SCGCQ00425363) Enhanced Event Log to include CVPM health details after every Learn Cycle to allow closer monitoring of CVPM health (SCGCQ00819877) - Implemented a retry for reads of CVPM data to avoid erroneous event 386 or 150 in the Event Log (SCGCQ00392439) - Added ability for firmware to report the temperature for all SAS/SATA HDD/SSD (SCGCQ00490819) - Implemented ability for firmware to read drive temperature immediately following SAS discovery (SCGCQ00602573) - Added ability to clear the MaintainPdFailHistory (SCGCQ00474559)
Version 23.29.0-0015 - Critical ------------------- Enhancement - Provide mechanism to disable PCIe backchannel training via SBR. Fixes: - Fixed an issue where the ‘cli set securitykey=Lsi@12345’ command fails with error code 1001 and error message invalid key. - Fixed an issue where foreign configuration import could fail. - Fixed an issue where storcli.exe /c0 show all command repeatedly prints to termlog with respect to upgradekey presence. - Fixed an issue where boot message ‘cached data was lost,’ even when there was no battery present. - Fixed an issue where the order of the first 64 VDs in the POST is not the same sequence as returned from the firmware. - Fixed storCLI adpfwflash option crash and adpallinfo option failure. - Reduced the bootblock Init time, which effectively reduces the configuration retry time to approximately 700 mS.
Version 23.22.0-0024 - Non-Critical ------------------- Enhancement(s): - Display the Native Command Queuing (NCQ) enabled/disabled status of every SATA disk drive in the output of StorCLI and MegaCLI. - Added support for ServeRAID M5100 Series 2GB Flash/RAID 5. Fix(es): - Disable PI CRC checking when the drive is not initialized during a CC. - Increased the SuperCap learn time out value for 2GB TMM-B solution. - Fixed an issue for 2GB memory modules where SuperCap does not get connected to the controller and hence cache offload fails. - Fixed an issue where cache policy of virtual drives(VD) does not change to write through(WT) mode even after detecting a bad supercap. - Fixed an issue where a RAID configuration created with physical disks in powersave mode could be lost after rebooting the system. - Fixed an issue where an invalid frame sent during a PIO-mode SATA passthrough command results in resetting the drive. - Fixed an issue where the system is not allocating memory correctly when MR and iMR controllers are in the same system. - Fixed an issue where deep learn does not start immediately when the relative state of charge (RSOC) is just equal to 95%. - Fixed an issue where performing a re-key operation in external key management (EKM) mode without doing a reboot, and then switching to local key management Mode(LKM) results in the Firmware logs showing that a drive security key was created but HII says the key is incorrect. - Fixed an issue where on a local key management (LKM) enabled controller, the user is asked to enter the security key to unlock and import a foreign drive, which is locked and has external key management (EKM) enabled.
Version 23.16.0-0027 - Critical ------------------- Fix(es): - Addressed data exposure issue when using CacheCade - Fixed issue where Supercap shows 0 Capacitance - Fixed iBBU09 battery issue that caused a VD cache policy to remain in write-through mode after a manual relearn - Fixed iBBU09 battery issue that caused a VD cache policy to periodically toggle between write-back/write-through mode - The limits for iBBU09 battery charging were not updating properly in a learn cycle - Ensures a single supercap pack is not supported on 2GB memory module. - Resolves a firmware crash seen while doing continuous sas cable pulls. - Ensures OpROM loads even if segment address is 0xC0000. - Fixed an issue where the adapter is running iMR machine checking after requesting host memory. - Fixed an issue where HII does not allow the user to make use of the remaining free capacity to configure additional VD for R50/R10. - Fixed an issue where an HII: empty warning prompt is given when creating a CacheCade VD with forced writeback option. - Fixed and issue where Windows cannot install without a VGA device on board. - Fixed and issue in EFI WebBIOS were consistency check is still shown in progress after 1 PD is removed from a R1 array.
Version 23.16.0-0018 - Suggested ------------------- Fix(es): - Fixed an issue where the adapter is running iMR machine checking after requesting host memory. - Fixed an issue where HII does not allow the user to make use of the remaining free capacity to configure additional VD for R50/R10. - Fixed an issue where an HII: empty warning prompt is given when creating a CacheCade VD with forced writeback option. - Fixed and issue where Windows cannot install without a VGA device on board. - Fixed and issue in EFI WebBIOS were consistency check is still shown in progress after 1 PD is removed from a R1 array.
Version 23.12.0-0016 - Suggested ------------------- Fix(es): - Added isync to prevent speculative execution while memory is being allocated. - Delayed enablement of POM until AFTER valid memory range is provided by host system.
Version 23.12.0-0011 - Suggested ------------------- Enhancement(s): - Support for 512e and 4k SAS/SATA hard drives added - Implemented Limited Band Charging for iBBU09 (RETAIN tip H21631) - Changed BIOS check to determine if running in HAMR, in order to ensure nothing gets broken when user has an iButton which is not programmed. - Changed controller status for safe mode to show controller status as safe mode and disable debug message logging in serial port.
Fix(es): - Addressed an issue where deeply discharged Cache Vault Power Modules would be prematurely be marked as failed. - Fixed an issue where HII hangs when trying to enter configuration management while in safe mode. Changed the safe mode warning message as below: "Controller is running in safe mode. Safe mode is used for diagnostic purposes only. Limited operations such as Configuration Preview, Clear Configuration and View/Change Controller Properties are allowed in this mode. Other operations such as Create Configuration, Import and Clear Foreign Configurations are not allowed. To exit safe mode, correct the fault, and reboot your computer." - Fixed an issue where having more than three adapters results in a calculation error for the offset to store physical disk info for fourth adapter, due to BIOS not clearing upper byte of AX (that is AH which is containing some non zero value). - Fixed an issue where the Wrong spanned drive group size is displayed by WebBIOS (Ctrl-H).
Version 23.7.1-0010 - Suggested ------------------- Fixes: - Fix an issue related to the where the TSOC (EEPROM) is not able to read or write from the firmware which will result in the message "Incompatible secondary iButton present." - Fix a HII broswer issue where Cachecade virtual drive can be selected as a boot device. - Fix a HII broswer issue where the user is unable to clear the controller configuration when there are no drives attached. - Fix an issue where the BIOS doesn't display the RAID level and VD size correctly at BIOS POST.
Version 23.7.1-0009 - Suggested ------------------- Fixes: - Fixed an issue where SoH is bad after a learn cycle but iBBUI shows good status. - Fixed an issue where hi-temp warning was not being displayed.
Version 23.7.0-0037 - Suggested ------------------- Fixes: - Corrected differential signals for Phys 2 and 3 that caused slot numbers in simple swap configurations to be incorrect. - Fixed an issue when 'maintain PD failed history' is enabled, and a cable is removed while a drive is added, the drives state goes to optimal instead of foreign unconfigured bad. - Fixed a problem where a capacity change is reported after a rebuild completes on a Cache Cade volume. - Fixed a controller firmware hang when the recovery of a medium error takes to long. - Fixed an issue where the SATA BBM (Bad Block Manager) list was being corrupted. - Fixed an issue where FoD (Feature on Demand) Options were being lost because of errors while accessing the TSOC. - Fixed a problem where the controller firmware would crash and drives would go offline when a bad block entry was created during a check consistency operation. - Fixed a problem where drives were being marked unconfigured bad (foreign) on reboot. - Fixed problem where a member of a CacheCade volume did not get marked as foreign when the drive was pulled with 'maintain PD failed history' enabled. - Fixed a problem where during a rebuild, a former hot spare that was now in a state of unconfigured good, moved back to the state hot spare, which then automatically started a copyback operation, causing the rebuild to restart. - Fixed a problem where a controller fault occurred during a reboot while a physical device was in progress of a PD Erase.
Version 23.7.0-0029 - Suggested ------------------- Enhancements: - Added support for Cache Cade 2.1 - Added Support for PI Drives
Fixes: - Fixed an issue where the firmware reports device initialization completion status to be greater than 100% at startup. - Fix an issue where when a secure foreign drive was present, VD creation fails because firmware becomes unresponsive - Added a check for the presence of PD before writing the data arms of a protected LD during BGI. - Fixed Firmware asserts in CacheMemAllocForPrebootApps() when memory was allocated twice by BIOS. - Fixed an issue with USB Cacheoffload restore fails after multiple power cycles onServeRAID M51xx controllers. - Fixed an issue where querying SMART / PFA Status returns "all zeros" in Sense Data. - Fixed an issue where the import of a config from MR to iMR resulted in a firmware crash. - Fixed an issue where iMR firmware crashed while creating 8/16/32 KB stripe size Lds. - Fixed background initialization watermark conversion to PD LBA. - Fixed write protected R1E data arms during initialization. - Fixed an issue where MR firmware crashed while discarding pinned cache. - Fixed an issue where a dirty LD dependency information of SSD pd has stale entries. - Corrected an issue during system booting from pinned cache, firmware goes to loop message BootMsgDcmd - Fixed an issue where a BGI was aborted and restarted, elapsed time was not reset. - Fixed an issue where the start ref for a shared cache line was not an indicator of the offset into the stripe. - Fixed an issue where the firmware hangs while running CC on a rebuilt R1 VD with SBBM. - Fixed an issue where the firmware was wrongly adding puncture entries. - Fixed an issue where rebuild was ran twice on a target drive with 100% full SBBM table. - Fixed an issue where the firmware was generating powersave change event when DS3 was not enabled, due to this application are not parsing the event. - Fixed an issue where recon from R0 to R1 using 3 TB drive causes firmware to report excessive unexpected sense events. - Fixed an issue, in which the bbuMode would revert to the factory default value of 5, when automatic learn cycle was enabled. - Fixed an issue where cache offload firmware reports unnecessary High Temp Event due to incorrect temp value. - Fixed an issue in which a Patrol Read may not start under certain conditions. - Fixed an issue where the firmware hits montask after discarding the cache when a snapshot VD was involved. - Fixed an issue where the firmware hangs during pin cache destage as dirty lines in that map never become zero. - Fixed an issue where CC fails to correct media error at 2TB location on 2 3TB SATA drives that support WU. - Fixed an issue where a new XML file was added to the nvdata, the buffer to hold the uncompressed nvdata overflowed. - Fixed an issue where an imported drive becomes unconfigured good when secure VD erase was running. - Fixed an issue where CC stops progressing on a R6 VD with media errors. - Fixed an issue where 3TB Hitachi HDD failed in immunity test (Electrostatic Noise test). - Fixed an issue where controller features are lost if RAID Key was not detected. - Fixed an issue where performance degraded in RAID 5 Sequential Writes due to command Out-of Ordering. - Fixed an issue where "Native configuration is no longer supported" message in post. - Fixed an issue where (DDR3) Initialization fails with fault 0x91a1 - initial DFIRL selected too low. - Fixed an issue where subsequent drives are dropped when all drives in the stagger spin up drives fails on boot sequence.
Version 23.2.1-0043 - Suggested ------------------- Fixes: - Fixed an issue where "Potential non-optimal configuration due to drive PD commissioned as emergency spare" alarm would trigger erroneously. - Fixed an issue where Copyback does not progress upon inserting drives. - Fixed an issue When allowMixInLD is Disabled, and causes Copyback Fails after Rebuild to Emergency Hot Spare. - Fixed an issue where the Firmware faults while flashing. - Fixed an issure where querying SMART / PFA Status to Return all zeros in Sense Data. - Fixed an issue where the Re-inserted Drives becomes Unconfigured_good causing auto rebuilds to fail to start.
Version 23.2.1-0033 ------------------- - Initial release ibm_fw_sraidmr_6gb-23_34_0-0018_linux_32-64_chg
IBM System x3850/x3950 X5/MAX5 uEFI Flash Update Version 1.85 (BuildID G0E185A) Change History
Version 1.85 - BuildID: G0E185A - Critical ----------------------------------------------------- Problem(s) Fixed: - Fixed excessive single bit memory errors reporting by mcelog daemon in Linux, refer to Retain TIP H214338 for details. - Eliminate unnecessary TPM error messages under Linux OS, refer to Retain TIP H91112 for details. Enhancements: - None Limitations: -Limited Solaris 10 operating system support, refer to RETAIN Tip H212469 for details. Dependencies: - IMM YUOOG8C (Version 1.48) or later is required. - FPGA G0UD92B (Version 5.02) or later is required.
Dependencies: - IMM YUOOG6C (Version 1.44) or later is required. - FPGA G0UD92B (Version 5.02) or later is required.
Version 1.83 - BuildID: G0E183A - Suggested ----------------------------------------------------- Problem(s) Fixed: - Add description of specific error code in system event logs when memory correctable errors happens - Update the information of memory pair entries for uncorrectable memory errors Enhancements: - None Limitations:
Dependencies: - IMM YUOOG6A (Version 1.43) or later is required. - FPGA G0UD92B (Version 5.02) or later is required.
Version 1.81 - BuildID: G0E181B - Critical ----------------------------------------------------- Problem(s) Fixed: - Power off the server after N boot attempts without locating a boot device - Add Scrub Failure message in IMM log for Data Queue memory training failures during POST. Please refer to RETAIN Tip H211626 for details. - Optimized MAX5 chipset settings to avoid reset in EXA-scaled configurations Enhancements: - None Limitations:
Dependencies: - IMM YUOOG2C (Version 1.42) or later is required. - FPGA G0UD92B (Version 5.02) or later is required.
Version 1.79 - BuildID: G0E179B - Critical ----------------------------------------------------- Problem(s) Fixed: - Addressed Intel errata BP57 and BA138 System Resets with 32-bit (PAE Enabled) Guest OS and VT FlexPriority Enabled. For more information, refer to IBM RETAIN Tip H21370
Enhancements: - Update microcode for Intel Xeon E7 series processors to M05206F2_00000037 - Update microcode for Intel Xeon 7500 series processors to M04206E6_0000000A
Limitations:
Dependencies: - IMM YUOOF7C (Version 1.41) or later is required. - FPGA G0UD91A (Version 5.01) or later is required.
Version 1.79 - BuildID: G0E179A - Critical ----------------------------------------------------- Problem(s) Fixed:
Enhancements: - Add notification and recovery option when UEFI detects GPT corruption during POST. Please refer to RETAIN Tip H21166 for details. - Add IPV6 PXE support. - Optimized Memory Single Bit Thresholds.
Limitations:
Dependencies: - IMM YUOOF7A (Version 1.40) or later is required. - FPGA G0UD88B (Version 4.01) or later is required.
Version 1.77 - BuildID: G0E177A - Critical ----------------------------------------------------- Problem(s) Fixed: - Limits C-states to avoid CPU VRD failures. Please refer to RETAIN Tip H207008 at the following link: http://www.ibm.com/systems/support/supportsite.wss/docdisplay?brandind=5000008&lndocid=MIGR-5091926 - Fix incorrect memory size report in F1 setup/OS when unusable DIMM was detected and isolated. - Fix disk data corruption with LUNS greater than 2TB for QLogic HBA Cards. - Fix F1 setup storage option missing issue for QLogic HBA card. - Fix initial values selected in the "Custom" operating mode are not the same as the previously selected preset operating mode.
Enhancements: - Add _WDG ACPI method support for SRIOV. - Add PCI-SIG resizable BAR capability support. - Support memory sparing function on a 2-nodes QPI linked system.
Limitations:
Dependencies: - IMM YUOOF2A (Version 1.36) or later is required. - FPGA G0UD87C (Version 4.00) or later is required.
Version 1.75 - BuildID: G0E175B - Critical ------------------------------------------------- Problem(s) Fixed: - Resolve OS or POST hang following a corrected machine check event. - Don't enable secondary video adapters in pre-boot environment to prevent Legacy VGA I/O conflict in Windows. - Fix boot fail when using WOL. - Addressed Intel errata BP47 and BA131 with title "A Load May Appear to be Ordered Before an Earlier Locked Instruction".
Enhancements: - Add Setup Option to select MM Config Base (1GB/2GB(default)/3GB). - Optimize PCI Resource Allocation for Onboard Devices to make more Legacy I/O and MMIO space available to Adapters. - Add setup option to set VLAN ID. - Add infinite boot loop option in F1 SETUP for legacy boot. - Update microcode for Intel Xeon E7 series processors to M05206F2_00000036. - Update microcode for Intel Xeon 7500 series processors to M05206E6_00000009.
Limitations:
Dependencies: - IMM YUOOE3C (Version 1.33) or later is required. - FPGA G0UD82B (Version 2.03) or later is required.
Version 1.73 - BuildID: G0E173B - Suggested ------------------------------------------------- IMPORTANT: IMM firmware YUOOD4G (Version 1.32) and FPGA firmware G0UD81B (Version 2.02) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.32 or later before you update the UEFI firmware.
Problem(s) Fixed: - Fix uEFI.UEFIRomDisable setting for secondary nodes. - Reset 3x Boot fail count upon any successful boot with user settings. - Make PCI Slot instance unique across nodes in SMBIOS Type 9 structures. - Fix VMWare Boot fail after installing it in UEFI mode. - Fix Processor Details in UEFI F1 Setup for CPUs with non-zero PBSP. - Fix system hang due to unhandled correctable SMI link event.
Enhancements: - Disable entire Secondary I/O Hub, if all it's Slots (1-to-4) are disabled. - Differentiate between QPI Link Width Reduction to Half vs Quarter Width. - Add support for Netlist DIMMs in SMBIOS Type 17 structures. - Add support for more than 255 PFs in Legacy MPS table. - Update microcode for Intel Xeon E7 series processors to M05206F2_00000034. - Support add-in video adapters behind Legacy I/O Hub Slots as Legacy VGA. - Add Setup Option to make 3x Boot fail configurable as Nx Boot fail. - Sync uEFI.RomOrder with the available devices in hardware configuration.
Limitations: Dependencies: - IMM YUOOD4G (Version 1.32) or later is required. - FPGA G0UD81B (Version 2.02) or later is required.
Version 1.71 - BuildID: G0E171A - Critical ------------------------------------------------- IMPORTANT: IMM firmware YUOOC7E (Version 1.30) and FPGA firmware G0UD72B (Version 2.01) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.30 or later before you update the UEFI firmware.
Problem(s) Fixed: - Fix false Three 3x Boot fail following replacement of battery. - Fix IMM MAC Address display in F1 IMM page. - Fix uEFI.VideoSelect default setting.
Enhancements: - Add support for 32GB DIMM. - Don't check for Legacy Option ROM Errors, when it is Disabled. - Update to SMBIOS 2.7 for extended DIMM size and Address space support. - F1 Network page update: categorized & consistent MAC notation. - Support Directory Assisted Snoop with Intel Xeon E7 series processors. - Describe I/O Affinity based on Setup Option of Non-Pooled (default) vs Pooled. - Add Setup Option to enable MMIO allocation above 4GB for large configuration. - Include MD5 checksum into firmware update package to prevent corrupted update. - Update microcode for Intel Xeon E7 series processors to M05206F2_00000032. - Improve Software Algorithms for Memory Robustness. - Limit boot attempts, when no bootable devices are found. - Add support for more than 2.2 TB disks with GPT. - Add Setup Option to disable the native control of PCI Express features from OS.
Limitations: Dependencies: - IMM YUOOC7E (Version 1.30) or later is required. - FPGA G0UD72B (Version 2.01) or later is required.
Version 1.60 - BuildID: G0E160B - Critical ------------------------------------------------- Version 1.60 is a major update release to support MAX5 multi node and also includes recommended updates for other single & multi node configurations.
IMPORTANT: IMM firmware YUOOB7C (Version 1.28) and FPGA firmware G0UD62C (Version 2.00) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.28 or later before you update the UEFI firmware.
Problem(s) Fixed: - When an SMI Lane Failover or SMI Link Failure event is detected during POST, the incorrect card number was shown in the POST Event Viewer log. - After a three times boot failure, scrolling the setup screens would leave garbled characters at the bottom of the screen. - Windows PE 32bit would boot without any PCI devices configured including USB keyboard and mouse. - WHEA corrected error events are being logged without corresponding IMM events. - Adapter with 512MB MMIO requirement installed in slots 1-4 reports a resource conflict.
Enhancements: - This release supports Machine Type 7145 or 7146 with Intel Xeon 7500 series processor, as well as, Machine Type 7143 and 7191 with Intel Xeon E7 series processors. - Added support for UEFI PXE boot in IPv6 environment. - Updated microcode for Intel Xeon E7 series processors to M05206F2_00000030. - Updated Intel Memory and QPI Reference Code to Version 2.11.
Limitations: - With the new default setting, the 2nd port of onboard Ethernet cannot be used for the legacy PXE boot. To legacy PXE boot from the 2nd port, enable the legacy option ROM for it. - After upgrading to this release internet Small Computer System Interface (iSCSI) devices configured to be bootable will no longer be bootable. Use the UEFI F1 Setup to reconfigure the iSCSI devices to work around this issue.
Dependencies: - IMM YUOOB7C (Version 1.28) or later is required. - FPGA G0UD62C (Version 2.00) or later is required.
Version 1.50 - BuildID: G0E152B - Critical ------------------------------------------------- Version 1.50 is a release for Machine Type 7143 and 7191 with Intel Xeon E7 series processors.
IMPORTANT: IMM firmware YUOOA6A (Version 1.26) and FPGA firmware G0UD57A (Version 1.05) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.26 or later before you update the UEFI firmware.
Problem(s) Fixed: - Microsoft Windows truncated memory dump file in EFI boot mode because the number of memory regions in EFI memory map was exceeding the limit of Windows. The problem was caused by fragmentation of EFI memory regions. - After three consecutive UEFI boot failures, UEFI setup settings were changed to default settings. - Corrected memory error WHEA events were incorrectly logged in the Windows system event log. - When add-in video adapter was installed in PCI-Express slot 1, UEFI Version 1.40 failed to boot. - Moving power-on password override jumper (J29 on I/O board) could not bypass the power-on-password prompt when UEFI Version 1.40 was installed. - Fixed detection of DIMM replacement and automatic reenabling of disabled DIMM.
Enhancements: - Added error reporting to inform when the legacy option ROM space is not enough to execute the option ROMs of all PCI adapters during legacy boot. - In order to reduce the chance of the legacy option ROM space error, the legacy option ROM execution order was changed so that onboard SAS option ROM will be executed earlier than onboard Ethernet option ROM. (Some of SAS adapters have option ROMs which comply with PCI firmware specification 2.1 while onboard Ethernet has option ROM which complies with PCI firmware specification 3.0.) - Updated Broadcom firmware to Version T6.2.4.1. - Added Extended APIC (X2APIC) support and a setup menu to enable or disable the Extended APIC.
Limitations: - This release does not support Machine Type 7145 or 7146 with Intel Xeon 7500 series processors yet, but supports only Machine Type 7143 and 7191 with Intel Xeon E7 series processors.
Dependencies: - IMM YUOOA6A (Version 1.26) or later is required. - FPGA G0UD57A (Version 1.05) or later is required.
Version 1.40 - BuildID: G0E140A - Suggested ------------------------------------------------- IMPORTANT: IMM firmware YUOO91D (Version 1.24) and FPGA firmware G0UD44D (Version 1.04) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.24 or later before you update the UEFI firmware.
Problem(s) Fixed: - Fixed a potential POST (Power-on-Self-Test) hang which might occur during recalibrating system power before OS starts. - Memory patrol scrub option was not functioning. The problem was corrected by updating Intel processor microcode and RAS code. - Redundant Bit Steering feature was not working for DIMMs greater than single rank in MAX5 memory expansion unit. - Red Hat Enterprise Linux 6 (RHEL6) installation could not be continued due to a video problem with EFI console output. - Disable propagation of Intel VT-d faults as fatal errors to avoid guest VM to cause the entire system to crash.
Enhancements: - Increase cooling fan speed if Fusion-io SSD PCI adapter is installed. - Added Advanced IMM Network Setup option to select data rate and duplex mode settings.
Limitations: Dependencies: - IMM firmware YUOO91D (Version 1.24) or later is required. - FPGA firmware G0UD44D (Version 1.04) or later is required.
Version 1.32 - BuildID: G0E131A - Critical ------------------------------------------------- Version 1.32 is a major update release to support MAX5 memory expansion and also includes recommended updates for single & multi node configurations.
IMPORTANT: IMM firmware YUOO75P (Version 1.19) and FPGA firmware G0UD43A (Version 1.02) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.19 or later before you update the UEFI firmware.
Problem(s) Fixed: - Fixed a potential problem with unexpected QPI inband resets when QPI link is running at 6.4GT/s. - There was incorrect data in MPS table which is used by legacy OS. - Fixed a PCI memory mapped I/O resource allocation issue where Broadcom network controller settings are overlaid causing invalid PCI Address ranges to appear to OS. The problem was caused by Broadcom firmware prior to Version T5.2.4.7 (Broadcom uEFI driver Version 5.2.15). - Fixed DMAR table for Intel Virtualization Technology for Directed I/O (Vt-d) with explicitly describing all PCI devices under the secondary root PCI bus.
Enhancements: - Enabled MAX5 memory expansion in single node configuration with maximum 1.5TB memory. - Added "Halt On Severe Error" setup option in Operating Modes setup menu which can prevent the system from booting into OS and shows POST Event Viewer if POST detects a severe error that caused an unexpected reboot.
Limitations: Dependencies: - IMM firmware YUOO75P (Version 1.19) or later is required. - FPGA firmware G0UD43A (Version 1.02) or later is required.
Version 1.23 - BuildID: G0E122D - Critical ------------------------------------------------- Version 1.23 is a major update release to support multi node configuration and also includes critical updates for single node configuration.
IMPORTANT: IMM firmware YUOO73K (Version 1.14) and FPGA firmware G0UD29C (Version 1.01) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.14 or later before you update the UEFI firmware.
Problem(s) Fixed: - Fixed risk of data errors when using firmware SCSI stack on Block I/O devices which are greater than 2TB with a GPT partition. (Please refer to RETAIN Tip H16222, MIGR-5084554 uEFI systems with HBA and > 2 TB LUN may have data consistency errors - IBM Servers.) - Mellanox InfiniBand adapter disappears after warm-reset. - Memory cards may not be correctly recognized or initialized after a reset due to a race condition during the memory card initialization. - Potential memory error occurring at 978MT/s speed due to an incorrect DIMM register setting. - Intermittent QPI lane width reduction events that could result in software NMI resets when PCI-Express bus is stressed. - Performance problem with legacy PXE network boot. The problem was caused by the onboard Broadcom network controller firmware prior to Version T5.2.4.4. - PCI-Express link training problem with some adapters which support Gen2 speed.
Enhancements: - Enabled multi node configuration, maximum 8 CPU sockets (128 logical CPUs) and maximum 2TB memory. - Enabled Intel Virtualization Technology for Directed I/O (Vt-d). - Improved link stability for PCI-Express root ports and QPI (Intel QuickPath Interconnect).
Limitations: Dependencies: - IMM firmware YUOO73K (Version 1.14) or later is required. - FPGA firmware G0UD29C (Version 1.01) or later is required.
Version 1.02 - BuildID: G0E107D - Critical ------------------------------------------------- Problem(s) Fixed: - Fixed an NMI problem caused by a downlevel firmware of ServeRAID M5015 SAS/SATA adapter (46M0829). This change reports the downlevel firmware and adjusts error reporting to allow the system boot to the firmware update, also allows unattended firmware update. - Fixed a problem which mistakenly reports a double bit memory error and disables the memory DIMMs. - Changed the UEFI BIOS default setting for processor C-state (ACPI C3) to disable in Performance mode and Custom mode.
Integrated Management Module (IMM) Firmware Update Change History
IMPORTANT: Prerequisite for updating to IMM firmware version 1.30 (yuooc7e) ========== Updating to IMM firmware version 1.30 (yuooc7e) requires the current IMM firmware version to be 1.10 (yuoo57h), or later. If this prerequisite is not met before updating to version 1.30 (yuooc7e) the system will not power on correctly. If the system is not running a minimum of IMM version 1.10 (yuoo57h), update the IMM before attempting to update to 1.30 (yuooc7e). This prerequisite was a limitation of IMM version 1.30, and it has been fixed in IMM version 1.31(yuooc7f). This prerequisite does not apply to IMM version 1.31 or later.
IMPORTANT: Please DO NOT apply the firmware update (yuoo91e, v1.24) ========= if you are using AEM functions in x3620M3 or x3630M3. The v1.24 firmware will disable the power capping functionality in those two systems. Please remain on the current IMM version or update the firmware to v1.25 or newer. Users not using AEM functions can still update to v1.24.
IMPORTANT: Read before using the MAX5 ========== This Technical Update supplements the documentation that comes with the IBM MAX5 for System x. Keep this document with your other MAX5 documentation. Before you attach the MAX5 to the server and try to use it, you must update the server firmware with the latest level of firmware or code. If you attach and try to use the MAX5 without updating the server firmware, you might get unexpected system behavior or the server might not power on. For special instructions to follow before you attach the MAX5 to the server, go to http://www.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-5085756.
IBM maintains pages on the World Wide Web where you can get the latest technical information and download device drivers and updates. To access these pages, go to http://www.ibm.com/systems/support/ and follow the instructions.
IMPORTANT: If you are at IMM firmware versions prior to 1.12 (yuoo67c) and ========== updating IMM firmware in Microsoft Windows, when you update IMM to versions between 1.14 (YUOO73M) and 1.30 (YUOOC7E), it will take up to 10 minutes additional wait time; when you update IMM to version 1.30 (YUOOC7E) or later, it will take up to 20 minutes additional wait time. This is due to the iflash tool checking the IMM before flashing. During this time the flashing process may appear hung or unresponsive. The flashing will then complete and there is no functional impact.
IMPORTANT: Make sure the current IMM firmware level is 1.14 or later ========== before you update the uEFI, FPGA, or DSA Preboot firmware. The recommended firmware update sequence is IMM followed by UEFI followed by FPGA followed by DSA Preboot.
IMPORTANT: A firmware change was made in YUOO57H (v1.10) that enforces the ========= requirement for login accounts on the IMM to have passwords that contain both alpha and numeric characters. If you are updating the IMM firmware from YUOO56K (v1.09) or earlier, to YUOO57H (v1.10) or newer, prior to updating the firmware, please ensure that the IMM user account passwords contain both alpha and numeric characters. If the firmware is updated and the passwords do not contain both alpha and numeric characters, you may need to reset the IMM to its default settings using the menus in the UEFI F1 set up display.
IMPORTANT: When updating the IMM firmware from a version earlier than ========= version 1.05 (build YUOO32F) to version 1.05 or newer, the Remote Alert Recipient Email Addresses and the Daylight Saving Time setting will revert to the default setting. Users that utilize these settings will need to set them again after the update.
IMPORTANT: When updating IMM, uEFI, pDSA, FPGA via any method, ========== please follow firmware update best practice document (http://www-947.ibm.com/support/entry/portal/docdisplay?brand= 5000020&lndocid=MIGR-5082923) for suggested update sequence and prerequisite.
IMPORTANT: Due to an Intel errata, if your server is running a 32-bit Linux ========== Operating System, C-states may need to be disabled while updating uEFI, IMM, or DSA Preboot through the Linux command line interface. See RETAIN TIP H195678 for more information. Updates performed through the AMM, Bootable Media Creator, or the IMM web or CLI interfaces do not have this requirement.
IMPORTANT: Updated firmware version numbers might not be visible in SMBIOS ========== tables until after the server is rebooted.
IMPORTANT: After downgrading IMM firmware from version 1.22 ========== to an earlier version, the user needs to reset the IMM to factory default before normal operation.
Version 1.52, YUOOH3A Problem(s) Fixed: - Fixed the following problem which was found in H2B. Web application potentially vulnerable to Clickjacking. - Disable arcfour ciphers for SSH in high security mode. - Updated the firmware to address security vulnerabilities: CVE-2015-8710, CVE-2015-5185, CVE-2016-0701, CVE-2016-2177, CVE-2016-2178
Version 1.51, YUOOH2B Problem(s) Fixed: - Fixed the following two problems which were found in H1C. New events can't be displayed in IMM event log after changing https status from enable to disable or vise versa. Email alerts can't be generated. - Updated the firmware to address security vulnerabilities: CVE-2015-7981, CVE-2015-8126, CVE-2016-0705, CVE-2016-0798, CVE-2016-0797, CVE-2016-0799
Version 1.50, YUOOH1C Problem(s) Fixed: - Update openssl to 1.0.2d. - Updated the firmware to address security vulnerabilities: CVE-2015-3200, CVE-2015-3195 - Disable CBC cipher and weak MAC algorithm for SSH in high security mode.
Version 1.49, YUOOG9A Problem(s) Fixed: - Updated the firmware to address security vulnerabilities: CVE-2015-4000, CVE-2009-5146, CVE-2015-0209, CVE-2015-0286, CVE-2015-0287, CVE-2015-0288, CVE-2015-0289, CVE-2015-0292, CVE-2015-0293, CVE-2015-1788, CVE-2015-1789, CVE-2015-1790, CVE-2015-1791, CVE-2015-1792, CVE-2015-3216, - Enhance LDAP client security in high security mode of IMM. This is to remove the low security of cipher suite during the security LDAP communication. - Fix the IE8 compatiblity issue of IMM web (security page) interface for Customer. - Enhance logging for the case of losing configuration.
Version 1.48, YUOOG8C Problem(s) Fixed: - Updated the firmware to address security vulnerabilities: CVE-2015-0204, CVE-2014-3570, CVE-2014-3572, CVE-2014-8275, CVE-2015-2808, CVE-2014-0191, CVE-2014-3660 - Fixed the issue where one invalid password entry for LDAP connection causes user lockout - Fixed the issue where password may become empty if it's updated by ASU tool through KCS interface.
Version 1.47, YUOOG7C Problem Fixed: - Updated the firmware to address these vulnerabilities: CVE-2014-3566, CVE-2014-3568 - Fixed the problem that session cookie does not have the "HttpOnly" property
Version 1.46, YUOOG7A Problem Fixed: - Enabled multicast filter to avoid IGMP flood on HS22, HS22V, HX5 Enhancements: - Updated the firmware to address these vulnerabilities: CVE-2013-2174, CVE-2014-0015, CVE-2014-0138,CVE-2014-0139 - Russia time zone update
Version 1.45, YUOOG6D Problem Fixed: - - Fixed a problem on the x3550M3 where the IMM2 reports the SNMP engineID in ASCII instead of hexadecimal.
Version 1.44, YUOOG6C Problem Fixed: - Critical Fix for x3550M3, x3650M3, dx360M3, x3630M3, x3400M3, x3620M3, x3500M3, x3200M3, x3250M3, dx360M2, x3550M2, x3650M2, x3400M2, x3500M2, x3850/x3950X5, x3690X5 -- Updated the firmware with patches to address the OpenSSL vulnerabilities listed in CVE-2014-0224, CVE-2014-0076 Enhancements: N/A
Version 1.43, YUOOG6B Problem Fixed: - Updated the firmware to address security vulnerabilities: CVE-2013-4560, CVE-2013-4559 - Fixed the problem that the LDAP group filter name changed after upgrading IMM. - Fixed the problem on blade servers where the management bus will become unstable if the AMM in slot1 is removed from chassis. - Fixed the problem that the SNMP engine ID is changed after IMM reset.
Version 1.42, YUOOG2C Problem Fixed: - Fixed a NTP sync problem on IMM web - Fixed a time zone setting problem on IMM web
Enhancements: - Added SHA256 and SHA512 support - Add a message in IMM event logs when power on is blocked due to VRD issue on x3850 X5 - Power off the server after N boot attempts without locating a boot device on x3850 X5/x3950 X5/HX5.
Version 1.41, YUOOF7C Problem Fixed: - Fixed the problem on blades where sometimes no throttle event was reported by AMM when CPU temperature is higher than Tcontrol. Enhancements: - Enhanced logging for throttle and Power Management.
Version 1.40, YUOOF7A Problems Fixed: - Fixed the problem on x3690X5 that host OS will be shut down due to wrong overtemp event. - Fixed the problem that "unsupported software version" could be showed in event logs after updating IMM version 1.30 or newer on x3850/x3950 X5, x3690X5 and HX5 - Fixed the problem that SMTP user name field on IMM web page only allows 16 chars. - Fixed the problem on HS22 where IMM reports 0 watt power during initialization
Enhancements: - Enabled IMM to fail over to backup automatically when there is a IMM firmware corruption - Enhanced IMM web GUI response. - Added notification when a corrupted GUID Partition Table (GPT) is encountered by UEFI during POST. Please refer to RETAIN Tip H207759 for details. - Enhanced logging for Power Controls management.
Version 1.39, YUOOF2C Problems Fixed: - Fixed the problem on IBM System x3850X5 where SAP HANA configurations can reset in rare cases. More details in RETAIN Tip H207295.
Version 1.38, YUOOF2B Problems Fixed: - Fixed the problem on x3850 X5/x3950 X5 where the System Fault LED will be lit when only one PSU is installed.
Version 1.37, YUOOE9C Problems Fixed: - Corrected the voltage sensor threshold for HS22 and HS22V system.
Version 1.36, YUOOF2A Enhancements: - Improved IMM web page Accessibility
Version 1.35, YUOOE9B Problems Fixed: - Fixed the thermal issue for Broadcom quad port ethernet (IBM PN 49Y7948., FRU 49Y7949). - Fixed the problem that user authentication for LDAP with SSL will fail when Configured Credentials is enabled. - Updated the thermal profile for NVIDIA M2090 GPU card support in dx360 M3. - Fixed the problem on HS22 systems where pressing the KVM button too soon (right after Power LED starts blinking slowly) would make the KVM owner unable to be changed. - Fixed the problem on blade servers where IMM may report the "Unsupported blade/blower combination" error for 130W Westmere CPUs. - Fixed the problem on x3200 M3 where when power policy is set as "restore" or "always on" in uEFI, enforcing system shutdown during POST will cause automatic system boot-up. - Fixed the problem about SNMP drops intermittently and SNMP data cannot be accessed in a period of time - Fixed the problem on x3850 X5/x3950 X5 Multi-Node systems where "redundancy lost" event is not logged in the Primary Node when one of the power supplies in the Secondary Node is lost. - Optimized CPU power consumption calculation method for x3690 X5. - Fixed the problem on blade servers where IMM does not automatically recover NCSI. - Fixed the problem on blade servers that IMM constantly has "Init Failures" and fails to start up. - Fixed the Readme file problem that some IP addresses of LAN-over-USB instructions are inconsistent. - Fixed the CMOS Voltage Over Threshold problem on HS22V systems. - Fixed the problem that SSH login failed when the setting is configured as "Local first then Ldap" or ldap settings are not valid. - Fixed the problem that the IMM web interface responds too slowly or even fails to respond.
Enhancements: - Enhanced the entropy (randomness) when generating SSL keys. - Added secure SMTP authentication support. - Added I/O board VPD information in IMM web interface - Added the function of letting Location LED remain on after system power-off. - Enhanced event Severity reporting of the QPI Link LED on x3850 X5/x3950 X5 so that IBM Director can interpret it correctly. - Improved IMM version reporting for IBM Director. - Added a function to keep 110V Power Supply Redundancy by throttling the system for x3850 X5/x3950 X5. - Usability enhancement: all events will be checked by default on the alert setting web page. - Enabled ASU to control each sub-category for email alert recipient setting and SNMP alerts setting. - Added new BCH Midplane (that supports 8Gbit Fibre Channel) support. - Added the function to capture all IMM logs with one button click. - Enhanced the DataPower appliance blade support.
Version 1.34, YUOOE3E Enhancement: - Add support of the following fusion-io adapters : 1.2TB High IOPS MLC Adapter for IBM System x 2.4TB High IOPS MLC Adapter for IBM System x 365GB High IOPS MLC PCIe Adapter for IBM System x 785GB High IOPS MLC PCIe Adapter for IBM System x
Version 1.33, YUOOE3C Problems Fixed: - Fixed the problem that a blade's Fault LED is showed as "on" on AMM GUI while there is no active critical event and the LED on the physical blade is off. - Fixed the problem that the "Date" header is missing from the IMM SMTP trap. - Fixed the problem that the "Look Below" LED (CR48) on x3690 X5 Memory Expansion Board may turn on incorrectly when there are no errors detected. - Fixed the problem on x3850 X5/x3950 X5 where the system information in the IMM configuration file may be truncated and the incomplete system information will cause the HTTP server in IMM run into an unstable state. - Fixed the problem that the Scalability LED turns off after the IMM on either node of a 2-Node x3850 X5/x3950 X5 is reset. - Fixed the problem that IMM on x3850 X5/x3950 X5 might fail to start after the IMM firmware is successfully upgraded. - Fixed the problem where "Comm Errors" may occur when the IMM firmware on HX5 is upgraded. - Fixed the problem that dx360 M3 may have PCI errors when a NVIDIA M2090 GPU card is installed. - Fixed the problem that opening the ActiveX remote console closes all open tabs in the same Internet Explorer window. - Fixed the problem that x3550 M3 may occur ServerRAID BBU over temperature and ServerRAID M5016 over heat issues.
Enhancements: - Added Internet Explorer 9 support. - Changed the maximum User's Distinguished Name(DN) for LDAP from 128 bytes to 256 bytes. - Removed the limitation of 255 memberOf groups for an LDAP user in IMM. - Enhanced IMM Web session management. - Added an IMM command line (CLI) command for one time PXE boot option setting. - Added a new unique error code in AMM and changed the text in AMM and IMM for CMOS battery errors. - Updated Russia time zone definition to no more daylight saving time.
Version 1.32, YUOOD4G Problems Fixed: - Fixed a problem where IMM web interface does not lock out a user if the same user exhausts login retries and gets locked out through the SSH interface - Fixed a problem that caused the IMM to report false critical DIMM temperature events - Fixed an intermittent problem where sometimes the Power Supply DC status LED is not illuminated on the x3550 M2/M3, x3650 M2/M3, x3620 M3 and x3630 M3 - Fixed a problem that sometimes causes the IMM web interface to shut down after multiple invalid login attempts Enhancements: - Added Service Advisor support on x3850/x3950 X5 and x3690 X5 - Changed the IMM firmware to allow every service port to be Enabled or Disabled - Changed the IMM firmware to not disable the network interface when there is a conflict IP address on the network - Changed the IMM firmware to permit SSL client certificates to be managed while the SSL client is enabled
Version 1.31, YUOOC7F Problems Fixed: - Fixed the problem that after updating IMM firmware from versions prior to v1.10(YUOO57H) to v1.30(YUOOC7E) the system won't power on correctly
Version 1.30, YUOOC7E Problems Fixed: - Fixed the intermittent Power Supply error on x3550M2/M3 and x3650M2/M3 - Fixed the false alarm message for ArBel Power Supply on x3550M2/M3 and x3650M2/M3 - Fixed the issue that a blade intermittently does not respond to the system management bus on HX5 and HS22/S22V - Fixed the duplicate PECI messages issue on x3850/x3950 X5, x3690X5 and HX5 - Fixed the intermittent problem that a user can not login to IMM web after inventory from IBM Director - Fixed the problem that SMTP test alert doesn't work - Fixed the problem that SNMP remote alert doesn't work - Fixed the intermittent IMM reset problem - Fixed the SSL vulnerability issue Enhancements: - Added 64-bit ActiveX Remote Presence Client support - Added BGE overweight detection on HS22 - Added support of differentiating memory failures happening during UEFI POST and during run-time - Added support of reporting AC restore status on x3850/x3950 X5 - Added the change to include DIMM slot number info in the memory error event message
Version 1.29, YUOOB7F Problem(s) Fixed: - Fixed a problem where false memory configuration error messages are sometimes reported on the x3850/x3950 X5
Version 1.28, YUOOB7C Problem(s) Fixed: - Fixed a problem where the IMM sometimes records duplicate event log entries - Fixed a problem that caused the DIMM Bank number to not be correctly reported - Fixed a problem that prevented the system from powering on when there is a firmware mismatch - Fixed a problem that didn't allow a password to be saved if it contains a & or < character - Fixed a problem where the IMM VPD sometimes is not available on the web page - Fixed a problem where one port on the QLogic 8GB HBA card sometimes is not recognized - Fixed a problem that sometimes caused the DVD drive to disappear in RHEL5 after the IMM is reset - Fixed a false Power Supply failure message - Removed the error message pop up when changing the IMM password to default - Fixed the problem that BBU gets over temp during discharging on x3550 M3 - Corrected a problem where the BOFM address became permanent after BOFM is disabled on the AMM - Corrected a system hang when a Multi-Bit memory error occurs with a mixture of 2GB & 4GB DIMMs installed - Fixed the problem where the reported DC Power consumed on the dx360 M3 is higher than actual AC input power - Fixed the MIB mismatch issue - Fixed the incorrect OID in MIB Enhancements: - Added support for 32-bit ActiveX Remote Presence Clients - Added the ability to change the SMTP port number - Changed the firmware to completely shut down the telnet sevice when the telnet max user count is set to 0 - Added support for LDAP Active Directory Application Mode - Added support for LDAP Authentication Only Mode - Changed the firmware to report a configuration error if the CPU installed on the EXA system is not a Westmere CPU - Changed the firmware to allow the x3690X5 to be powered on sooner - Changed the firmware to decrease the amount of time that it takes for the IMM to become ready after it is reset
Version 1.27, YU00A7C Enhancements: - Added support for the IBM BladeCenter HX5(MT: 1910,7873)
Version 1.26, YU00A6A Enhancements: - Added support for the System x3850/x3950 X5(MT: 7143,7191) and System x3690 X5(MT: 7147,7192)
Version 1.25, YU0091K Problem(s) Fixed: - Fixed a problem that hangs the server when F2 is pressed during POST to start Diagnostics - Fixed a problem in the HS22/HS22v that causes the IMM to report an unexpected throttle condition after the AMM is reset - Fixed a problem that causes the IMM lose its DHCP assigned IP address - Improved the monitoring of hard drive status when the server is powered up - Fixed a problem when using a Japanese keyboard with the remote presence function - Fixed a gradual fan speed reduction due to pressure sensor fluctuation on System x3690 X5, System x3550 M2/3, System x3650 M2/3 - Improved the response to an IO Hub over temperature condition on System x3690 X5, System x3650 M2/M3, and System x3550 M2/M3 - Fixed a problem that IBM Systems Director needs to re-discover IMM in order to receive events from IMM after IMM upgrade Enhancements: - Added support for a 460W power supply in the System x3620 M3 - Added support for a 675W high efficiency power supply in the System x3620 M3 and System x3630 M3
Version 1.24, YU0091E Problem(s) Fixed: - Fixed a problem where the IMM sometimes incorrectly reports a Pwr Rail fault or Pwr 240A_A/Pwr 240A_B fault - Fixed an issue where blade would hang on boot with ABR firmware corruption message - Fixed a problem when downgrading IMM firmware from version 1.22 to earlier levels. The IMM network fails - Fixed a problem that caused the firmware update using IMM Command Line Interface to fail on an IPv6 network - Fixed a problem that caused the IPv6 Link-local address not to be displayed after resetting the IMM to its defaults - Fixed a problem where the IMM fails to set SNMP configuration using ASU - Fixed a problem where IMM cannot set the value 10 for the OSWatchdog value using ASU - Fixed a problem where IMM Remote Media would not re-initialize after network error - Fixed problem if KCS error bit status may not be clear which may cause KCS communication stop - Fixed a problem that IMM web interface hang with Remote Control session opened - Fixed a problem that blade unexpected powered on after power off command Enhancements: - Added IPv6 configuration support via IMM SNMP interface - Added support for BladeCenter PCIe Expansion 4 on BladeCenter HX5 - Added support for BladeCenter GPU Expansion on BladeCenter HS22 - Added support for LDAP sub-tree searching with Novell eDirectory 8.7 - Added support for SNMP trap definitions - Updated fan response and logic for Fusion IO PCIe adapter - Updated ambient temperature sensor calculation
Version 1.22, YUOO84C Problem(s) Fixed: - Fixed a problem where the IMM sometimes incorrectly reports a Processor 2 (CPU 2) internal error - Fixed a problem where after powering down an HS22, the HS22 powered on without user request - Fixed a problem while Log in to IMM might fail if the Host name contains a dash - Fixed a problem where the IMM makes some certificate management settings protected that should not be protected - Fixed a problem where users can't get the full details of an expansion card using the IPMI FRU command - Fixed a problem where IMM would hang after an LDAP login using some German or French characters - Fixed a problem with the IMM SMTP client not conforming to RFC821 - Fixed a problem where the email alert setting won't accept a hyphen - Fixed a problem with the Windows key in the IMM Remote Control feature - Fixed a problem where IMM login via LDAP authentication fails to acquire Supervisor authority via Group membership with an OpenLDAP server. - Fixed a problem where a user with Remote Server Power/Restart Access authority can't change the power off delay - Fixed a problem that prevented a Processor Throttled event from being logged for the x3200 M3 and x3250 M3 models - Fixed a problem that where a user's permission is always set from the LDAP account not the local account profile - Fixed a problem where the CPU2 VCore/CPU2 VDIMM sensors become unreadable after updating the IMM in the x3500 M3 model - Fixed problem for DHCP may get time out if using "Shared NIC" mode but without any LAN cable to be plugged into "Sys Mgmt" port Enhancement: - Added IPv6 support - Added Dynamic DNS support (IPv4 only) - Added support for BladeCenter PCIe Expansion 4 on BladeCenter HS22 - Added BCH-R3 support
Version 1.21, YUOO75V Enhancement: - Added support for BladeCenter Max 5 Memory Expansion Unit (MEU) - Added feature to report SMI Lane failure for BladeCenter HX5
Version 1.20, YUOO75T Enhancement: - Added support for Max 5 Memory Expansion Unit (MEU)for SystemX 3690 X5 - Added support for Max 5 Memory Expansion Unit (MEU)for BladeCenter HX5 - Added feature to show pending firmware level during firmware update process - Added feature to block power on when multi-node complex has firmware mismatch Problem(s) Fixed: - Fixed DASD LED behavior for drives 8-32 - Fixed fan over cooling on SystemX 3690 X5 - Fixed Flash failure due to packet loss - Fixed Power Cycle events not appearing in SystemX 3690 SEL - Fixed DIMM throttle behavior in acoustic mode for BladeCenter HX5 - Fixed CPU type checking
Version 1.19, YUOO75X Enhancement: - Added support for Max 5 Memory Expansion Unit (MEU)for SystemX 3850/3950 X5 - Added support for 130W CPUs in High Performance Blades - Added virtual NIC VPD support - Changed the default value of SerialExitCLIKeySequence to ^[( - Added TPM Physical Presence Sensor support - Added AC metering and capping to System x3850/3950 X5 Problem(s) Fixed: - Fixed server time out authority in web interface - Fixed non-recoverable events that appeared as warning events in web event log - Fixed Server State "unknown" status in web interface - Prevented multiple log entries from being created for the same event - Fixed IPMI multi-session handling when sessions fail - Fixed IMM flash failed at 0 percent update progress error - Fixed Internal Error 255 during FPGA update - Fixed CPU Overtemp messages on FPGA update. - Removed unnecessary events for Power Unit sensors - Fixed failure to log VRD error on voltage fault - Fixed Power Redundancy Sensor handling for 220V configurations - Fixed CPU configuration check for System x3850/3950 X5 - Fixed IMM Network ARP - Fixed flash error "Image transfer timed out - error 15" - Corrected a problem that caused the system to not automatically power on after performing an Automatic BIOS Recovery (ABR)
Version 1.18, YUOO75J Enhancement: - Added support for the System x3630 M3
Version 1.17, YUOO75H Enhancement: - Added support for the System x3690 X5
Version 1.16, YUOO73O Enhancement: - Added support for the BladeCenter System HX5
Version 1.14, YUOO73M Problem(s) Fixed: - Corrected the MIB file to address a compiling problem - Fixed a problem when a second CPU might not been recognized by the IMM, when cycling power on the System x3550 - Fixed a problem where web session may hang after staying on the System Status web page for a while - Disabled the interface to the shared network port when the dedicated systems management network interface is selected. - Fixed a web page pop-up error message that may occur after upgrading the IMM from 48d and 57f - Fixed power/thermal calibration error in the x3620 M3 - Fixed a problem where the IMM may log a CPU Automatically Throttled event or a Redundancy Lost for a cooling zone event in the log after cycling power - Fixed a problem where the IMM doesn't send an ambient temperature alert or IO Hub temperature alert in the x3400 M3 and x3500 M3 - Corrected a remote presence problem that occurs while mounting an ISO image if the remote client does not have any removable devices. Enhancement: - Added a fan control enhancement for performance mode - Added support for additional types of power supplies - Improved the accuracy of power readings on 3550 M3, 3650 M3, and 3620 M3
Version 1.14, YUOO73K (released for multinode System x3850 X5 and x3950 X5 only) Problem(s) Fixed: - Fixed a problem that caused the IMM not to respond to some IPMI commands - Corrected a problem with LDAP authentication when role-based security is enabled - Corrected a problem which could cause a false CPU error to occur - Prevented false automatic boot failure recovery events from being reported Enhancements: - Added multinode support for System x3850 X5 and System x3950 X5 - Added support to activate FPGA updates with a warm boot - Added support for AC power metering and AC power capping on single node System x3850 X5 and System x3950 X5 - Added support to improve permit early power on support - Add support to report the version information for updates that have been flashed but not yet activated - Added support to report an FPGA firmware mismatch
Version 1.12, YUOO67C Problems(s) Fixed: - Adjust the Planar VBAT voltage threshold in HS22 Enhancement: - Added support for the System x3620 M3 - Added support for DC power supplies in the System x3550 M3 and System x3650 M3
Version 1.11, YUOO56O Enhancements: - Improved ABR handling to prevent invalid ABR behavior
Version 1.10, YUOO57J (released for HS22 only) Problem(s) Fixes: - Fixed a problem where the IMM sometimes incorrectly reports a Processor 1 (CPU 1) internal error
Version 1.10, YUOO57H Problem(s) Fixed: - Made changes to improve the robustness of firmware update operations. - Corrected an LDAP authentication problem. - Corrected a problem where SNMP settings could be lost after updating the firmware. - Enable ssh by default. - Permit the Adavnced Setting Utility to enable or disable ssh. - Added support for logging a message when the blade CPU is not compatible with the chassis' blower capacity - Permit the realtime power management controller firmware to be flashed to an earlier level. - Corrected a problem that prevented the remote presence function from working with network address translation - Fixed an issue where blades would throttle/hang when chassis power supply is removed Enhancement: - Added support for the System x3550 M3, System x3650 M3, System x3500 M3, System x3400 M3, System x iDataPlex dx360 M3, and the HS22V blade - Enhanced power measurement and capping capabilities in support of xSmartEnergy control - Increased support for the number of DIMMs from 12 to 18
Version 1.09, YUOO56K Enhancement: - Added support for the System x3850 X5 and the System x3950 X5
Version 1.08, YUOO48F Problem(s) Fixed: - Made changes to improve the robustness of firmware update operations. Limitations: Limitations for versions 1.07 and 1.08: If you are down-leveling the IMM firmware to a version older than 1.07 and the IMM firmware is currently at version 1.07 or 1.08, you must remove AC power from the server before performing a server reboot.
Version 1.07, YUOO48E Prerequisites: IMPORTANT: This firmware update contains changes to permit servers ========== to be powered on sooner after plugging them into AC power. Before installing UEFI with firmware that supports the early power on changes, be sure to update the IMM with this firmware version. UEFI Firmware with early power on support: BladeCenter HS22 UEFI Build P9E131A or newer System x3550 M2 UEFI Build D6E131C or newer System x3650 M2 UEFI Build D6E131C or newer System x3200 M3 UEFI Build GYE129A or newer System x3250 M3 UEFI Build GYE129A or newer System x3400 M2 UEFI Build Y4E131B or newer System x3500 M2 UEFI Build Y4E131B or newer System x iDataplex dx360 M2 UEFI Build TME132A or newer Problem(s) Fixed: - Corrected an Ethernet bug that caused network packets to be dropped - Changed the firmware to improve server performance when the Ethernet over USB interface is enabled - Corrected an intermittent problem where some of the IMM interfaces would not function after flashing the IMM with new firmware - Corrected a problem where LDAP users in nested groups are not permitted access to the IMM - Corrected a problem where the fault LED is not lit on the HS22 server when a hard drive is removed - Fixed a problem where the IMM sometimes incorrectly reports faults when the server is power cycled (for example, a loss of redundancy or a critical fan fault, or a processor is operating in a Degraded State, etc...) - Corrected a problem where the server would sometimes hang at checkpoint 'E8' - Changed the firmware to light the Information LED if the primary UEFI bank becomes corrupted - Corrected a problem that prevented the Remote Disk on Card feature from properly working - Corrected a problem that prevented an HS22 server with a full configuration from powering on - Changed the firmware to send processor information to the Advanced Management Module for display - Corrected a problem where faults for fan numbers 2 and 4 for the System X3200 M3 were swapped - Corrected a problem where the IMM firmware could corrupt itself over time Enhancements: - Changed the firmware to permit servers to be powered on sooner after plugging them into AC power - Improved the performance when displaying pages on the web interface - Added support to permit management traffic over the daughter cards in the HS22 server
Version 1.06, YUOO39B Enhancement: - Added support for Machine Types 4251, 4252, 4261, 7327, 7328
Version 1.05, YUOO32F Limitations: Problem(s) Fixed: - This update package contains updated Management Information Base files for use when managing the server through the IMM's SNMP interface - Fixed a problem where user accounts and settings could become lost - Improved performance when changing settings through the web interface - Corrected a problem where some configuration settings were lost after flashing the IMM with new firmware - Improved the wording of messages in the Chassis Event Log - Restored the ability to the IMM SNMP interface to add or remove user accounts and to set the account security level - Corrected a problem that prevented some configuration settings from being set through the Advanced Setting Utility (ASU) - Fixed a problem that prevented a user from specifying an email alert recipient with a hyphen in the name - Fixed an IMM flash update problem where the IMM erroneously reports a CPU Configuration error and/or illuminates the fault LED on the HS22 Blade Server with no corresponding entry in the Advanced Management Module log - Fixed an IMM flash update issue which can result in blades never completing the Discovery state Enhancement: - Added support for the BladeCenter PCIe Expansion module 3 - Added support for servers running real-time Linux - Enhanced the automatic recovery of communication errors in BladeCenter - Added the ability to configure a hostname for SNMPV3 traps, rather than just an IP address
Version 1.04, YUOO24I Problem(s) Fixed: - This is a critical update for x3550 M2 and x3650 M2. It corrects a possible problem that can occur when adding options such as memory, hard drives, and Central Processing Units (CPUs), and makes the system may become unresponsive. In some cases the server cannot power on again, or network connectivity to the Integrated Management Module is not possible. The problem may also occur when rebooting the IMM while the system is powered on with certain hardware configurations. - Replaced the ibm_rndis_server_os.inf and device.cat in the IMM firmware update package for Windows. The new files are used to workaround a potential performance issue when the IMM's Ethernet over USB is enabled. Enhancement: - Added support for different hard drives - Added support that enables the Advanced Management Module to display CPU information for the HS22 blade.
Version 1.03, YUOO23C Problem(s) Fixed: - Removed the empty virtual drives that were presented to the server by default. Virtual drives are now not presented to the server unless media is present and mounted from the Remote Control client. Enhancement: - Added support for Machine Types 7836, 7837, and 7839
Version 1.02, YUOO19G Problem(s) Fixed: - Corrected a problem where a critical fan fault was erroneously logged when powering off the server
Version 1.01, YUOO19E Enhancement: - Added support for Machine Types 7946, 4198, 7947, 4199, 7321, 6380, 7323
Version 1.00, YUOO18D - Original Release - Supports Machine Types 7870, 1936
(C) Copyright International Business Machines Corporation 2008 - 2013. All rights reserved.
ibm_fw_imm_yuooh3a-1_52_anyos_noarch_chg
IBM System x3690 X5/MAX5 uEFI Flash Update Version 1.85 (BuildID MLE185A) Change History
Version 1.85 - BuildID: MLE185A - Critical ----------------------------------------------------- Problem(s) Fixed: - Fixed excessive single bit memory errors reporting by mcelog daemon in Linux, refer to Retain TIP H214338 for details. - Eliminate unnecessary TPM error messages under Linux OS, refer to Retain TIP H91112 for details. Enhancements: - None Limitations: -Limited Solaris 10 operating system support, refer to RETAIN Tip H212469 for details. Dependencies: - IMM YUOOG8C (Version 1.48) or later is required. - FPGA MLUD33F (Version 1.23) or later is required.
Dependencies: - IMM YUOOG6C (Version 1.44) or later is required. - FPGA MLUD33F (Version 1.23) or later is required.
Version 1.83 - BuildID: MLE183A - Suggested ----------------------------------------------------- Problem(s) Fixed: - Add description of specific error code in system event logs when memory correctable errors happens - Update the information of memory pair entries for uncorrectable memory errors Enhancements: - None Limitations:
Dependencies: - IMM YUOOG6A (Version 1.43) or later is required. - FPGA MLUD33F (Version 1.23) or later is required.
Version 1.81 - BuildID: MLE181B - Critical ----------------------------------------------------- Problem(s) Fixed: - Power off the server after N boot attempts without locating a boot device. - Add Scrub Failure message in IMM log for Data Queue memory training failures during POST. Please refer to RETAIN Tip H211626 for details.
Enhancements: - None Limitations:
Dependencies: - IMM YUOOG2C (Version 1.42) or later is required. - FPGA MLUD33E (Version 1.23) or later is required.
Version 1.79 - BuildID: MLE179B - Critical ----------------------------------------------------- Problem(s) Fixed: - Addressed Intel errata BP57 and BA138 System Resets with 32-bit (PAE Enabled) Guest OS and VT FlexPriority Enabled. For more information, refer to IBM RETAIN Tip H21370
Enhancements: - Update microcode for Intel Xeon E7 series processors to M05206F2_00000037 - Update microcode for Intel Xeon 7500 series processors to M04206E6_0000000A
Limitations:
Dependencies: - IMM YUOOF7C (Version 1.41) or later is required. - FPGA MLUD33D (Version 1.23) or later is required.
Version 1.79 - BuildID: MLE179A - Critical ----------------------------------------------------- Problem(s) Fixed:
Enhancements: - Add notification and recovery option when UEFI detects GPT corruption during POST. Please refer to RETAIN Tip H21166 for details. - Add IPV6 PXE support. - Optimized Memory Single Bit Thresholds.
Limitations:
Dependencies: - IMM YUOOF7A (Version 1.40) or later is required. - FPGA MLUD33D (Version 1.23) or later is required.
Version 1.77 - BuildID: MLE177A - Critical ----------------------------------------------------- Problem(s) Fixed: - Fix incorrect memory size report in F1 setup/OS when unusable DIMM was detected and isolated. - Fix disk data corruption with LUNS greater than 2TB for QLogic HBA Cards. - Fix F1 setup storage option missing issue for QLogic HBA card. - Fix initial values selected in the "Custom" operating mode are not the same as the previously selected preset operating mode.
Enhancements: - Add _WDG ACPI method support for SRIOV. - Add PCI-SIG resizable BAR capability support.
Limitations:
Dependencies: - IMM YUOOF2A (Version 1.36) or later is required. - FPGA MLUD33C (Version 1.23) or later is required.
Version 1.75 - BuildID: MLE175B - Critical ----------------------------------------------------- Problem(s) Fixed: - Resolve OS or POST hang following a corrected machine check event. - Don't enable secondary video adapters in pre-boot environment to prevent Legacy VGA I/O conflict in Windows. - Fix CPU VRD errors on MT 7148 and MT 7149. - Fix boot fail when using WOL. - Addressed Intel errata BP47 and BA131 with title "A Load May Appear to be Ordered Before an Earlier Locked Instruction".
Enhancements: - Add Setup Option to select MM Config Base (1GB/2GB(default)/3GB). - Optimize PCI Resource Allocation for Onboard Devices to make more Legacy I/O and MMIO space available to Adapters. - Add setup option to set VLAN ID. - Add infinite boot loop option in F1 SETUP for legacy boot. - Update microcode for Intel Xeon E7 series processors to M05206F2_00000036. - Update microcode for Intel Xeon 7500 series processors to M05206E6_00000009.
Limitations:
Dependencies: - IMM YUOOE3C (Version 1.33) or later is required. - FPGA MLUD32D (Version 1.23) or later is required.
Version 1.73 - BuildID: MLE173B - Suggested ----------------------------------------------------- Problem(s) Fixed:
- Reset 3x Boot fail count upon any successful boot with user settings. - Fix PCI Slot usage field in SMBIOS Type 9 structures. - Select first scanned from available add-in video adapters as Legacy VGA. - Fix VMWare Boot fail after installing it in UEFI mode. - Fix Processor Details in UEFI F1 Setup for CPUs with non-zero PBSP. - Fix system hang due to unhandled correctable SMI link event.
Enhancements:
- Differentiate between QPI Link Width Reduction to Half vs Quarter Width. - Add support for Netlist DIMMs in SMBIOS Type 17 structures. - Add support for more than 255 PFs in Legacy MPS table. - Update microcode for Intel Xeon E7 series processors to M05206F2_00000034. - Add Setup Option to make 3x Boot fail configurable as Nx Boot fail. - Sync uEFI.RomOrder with the available devices in hardware configuration.
Limitations:
Dependencies:
- IMM YUOOD4G (Version 1.32) or later is required. - FPGA MLUD32B (Version 1.22) or later is required.
Version 1.70 - BuildID: MLE170C - Critical --------------------------------------- Problem(s) Fixed:
- Fix false Three 3x Boot fail following replacement of battery. - Fix IMM MAC Address display in F1 IMM page.
Enhancements:
- Add support for 32GB DIMM. - Don't check for Legacy Option ROM Errors, when it is Disabled. - Update to SMBIOS 2.7 for extended DIMM size and Address space support. - F1 Network page update: categorized & consistent MAC notation. - Support Directory Assisted Snoop with Intel Xeon E7 series processors. - Describe I/O Affinity based on Setup Option of Non-Pooled (default) vs Pooled. - Add Setup Option to enable MMIO allocation above 4GB for large configuration. - Include MD5 checksum into firmware update package to prevent corrupted update. - Update microcode for Intel Xeon E7 series processors to M05206F2_00000032. - Improve Software Algorithms for Memory Robustness. - Limit boot attempts, when no bootable devices are found. - Add support for more than 2.2 TB disks with GPT. - Add Setup Option to disable the native control of PCI Express features from OS.
Limitations:
Dependencies:
- IMM YUOOC7E (Version 1.30) or later is required. - FPGA MLUD31G (Version 1.21) or later is required.
Version 1.60 - BuildID: MLE160A - Critical ----------------------------------------------------- Problem(s) Fixed:
- The system would boot with memory errors when memory mirroring was enabled. - After a three times boot failure, scrolling the setup screens would leave garbled characters at the bottom of the screen. - Windows PE 32bit would boot without any PCI devices configured including USB keyboard and mouse. - WHEA corrected error events are being logged without corresponding IMM events.
Enhancements:
- This release supports Machine Type 7148 or 7149 with Intel Xeon 7500 or 6500 series processors, as well as, supports Machine Type 7192 and 7147 with Intel Xeon E7 series processors. - Enabled support for early power on by IMM. - Added support for UEFI PXE boot in IPv6 environment. - Updated microcode for Intel Xeon E7 series processors to M05206F2_00000030. - Updated Intel Memory and QPI Reference Code to Version 2.11.
Limitations:
- After upgrading to this release internet Small Computer System Interface (iSCSI) devices configured to be bootable will no longer be bootable. Use the UEFI F1 Setup to reconfigure the iSCSI devices to work around this issue.
Dependencies:
- IMM YUOOB7C (Version 1.28) or later is required. - FPGA MLUD30J (Version 1.20) or later is required.
Version 1.40 - BuildID: MLE142A - Critical --------------------------------------- Version 1.40 is a release for Machine Type 7192 and 7147 with Intel Xeon E7 series processors.
IMPORTANT: IMM firmware YUOOA6A (Version 1.26) and FPGA firmware MLUD30G (Version 1.20) or later must be used in conjunction with this UEFI release. Please make sure the current IMM firmware level is Version 1.26 or later before you update the UEFI firmware.
Problem(s) Fixed:
- Microsoft Windows truncated memory dump file in EFI boot mode because the number of memory regions in EFI memory map was exceeding the limit of Windows. The problem was caused by fragmentation of EFI memory regions. - After three consecutive UEFI boot failures, UEFI setup settings were changed to default settings. - Corrected memory error WHEA events were incorrectly logged in the Windows system event log. - Fixed detection of DIMM replacement and automatic reenabling of disabled DIMM.
Enhancements:
- Added error reporting to inform when the legacy option ROM space is not enough to execute the option ROMs of all PCI adapters during legacy boot. - In order to reduce the chance of the legacy option ROM space error, the legacy option ROM execution order was changed so that onboard SAS option ROM will be executed earlier than onboard Ethernet option ROM. (Some of SAS adapters have option ROMs which comply with PCI firmware specification 2.1 while onboard Ethernet has option ROM which complies with PCI firmware specification 3.0.) - Updated Broadcom firmware to Version T6.2.4.1. - Added Extended APIC (X2APIC) support and a setup menu to enable or disable the Extended APIC.
Limitations:
- This release does not support Machine Type 7148 or 7149 with Intel Xeon 7500 or 6500 series processors yet, but supports only Machine Type 7192 and 7147 with Intel Xeon E7 series processors.
Dependencies:
- IMM YUOOA6A (Version 1.26) or later is required. - FPGA MLUD30G (Version 1.20) or later is required.
Version 1.31 - BuildID: MLE131A - Critical --------------------------------------- Problem(s) Fixed:
- SATA DVD drive may not be detected correctly. The problem was caused by incorrect ICH10 SATA controller setting which decreased SATA transmitter output voltage.
Enhancements:
Limitations:
Dependencies:
Version 1.30 - BuildID: MLE130A - Critical --------------------------------------- Problem(s) Fixed:
- Fixed a potential POST (Power-on-Self-Test) hang which might occur during recalibrating system power before OS starts. - Memory patrol scrub option was not functioning. The problem was corrected by updating Intel processor microcode and RAS code. - Redundant Bit Steering feature was not working for DIMMs greater than single rank in MAX5 memory expansion unit. - Red Hat Enterprise Linux 6 (RHEL6) installation could not be continued due to a video problem with EFI console output. - Disable propagation of Intel VT-d faults as fatal errors to avoid guest VM to cause the entire system to crash.
Enhancements:
- Added Advanced IMM Network Setup option to select data rate and duplex mode settings. - Updated Broadcom firmware to Version T6.0.4.2.
- Fixed a potential problem with unexpected QPI inband resets when QPI link is running at 6.4GT/s. - There was incorrect data in MPS table which is used by legacy OS. - Fixed a PCI memory mapped I/O resource allocation issue where Broadcom network controller settings are overlaid causing invalid PCI Address ranges to appear to OS. The problem was caused by Broadcom firmware prior to Version T5.2.4.7 (Broadcom uEFI driver Version 5.2.15). - Fixed DMAR table for Intel Virtualization Technology for Directed I/O (Vt-d) with explicitly describing all PCI devices under the secondary root PCI bus.
Enhancements:
- Enabled MAX5 memory expansion with maximum 1TB memory. - Added "Halt On Severe Error" setup option in Operating Modes setup menu which can prevent the system from booting into OS and shows POST Event Viewer if POST detects a severe error that caused an unexpected reboot. - Automatically switch to add-in video adapter from the onboard video controller with setup default setting if add-in video adapter is installed.
Dynamic System Analysis (DSA) Preboot Change History
Version 9.27, Build ID DSYTA7 o New System Support: o New Operating System support: o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: Refer to readme o Functional change: o Dependencies: o Special usage: - IMMv1 system 2012 4Q-LFC
Version 9.26, Build ID DSYTA6G o New System Support: o New Operating System support: o New server options support: o Problem(s) Fixed: o Enhancement: DSA Performance Optimization o Limitations: Refer to readme o Functional change: o Dependencies: o Special usage: - 2012 ToolsCenter 12C
Version 9.21, Build ID DSYTA1U o New System Support: o New Operating System support: o New server options support: o Problem(s) Fixed: 1.Recovered LSI Rawdata: "MegaCli -FwTermLog -Dsply -aALL" o Enhancement: o Limitations: Refer to readme o Functional change: o Dependencies: o Special usage: - 2012 ToolsCenter 12B Plus
Version 9.20, Build ID DSYTA0R o New System Support: x3530 M4 (7160) x3630 M4 (7158) x3750 M4 (8722, 8733) HS23E (8038, 8039) Flex System x220 Compute Node (7906, 2585) o New Operating System support: vSphere Hypervisor 5.0u1 with IBM customization o New server options support: o Problem(s) Fixed: 1. PMR 05819,YL2,760 An error occured during the execution of DSA on Windows, DSA exits with an error at the eventlog plugin.
o Enhancement: o Limitations: Refer to readme o Functional change: 1. Add HW remote presence key collection for High volume systems. o Dependencies: o Special usage: - 2012 ToolsCenter 12B
Version 9.07, Build ID DSYT9CA o New System Support: x3750 M4 (8722, 8733) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 9.06, Build ID DSYT9BC o New System Support: Flex System x220 Compute Node (7906) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 9.05, Build ID DSYT9AA o New System Support: x3630 M4 (7158) x3530 M4 (7160) x3100 M4 Refresh1 (2582) x3250 M4 Refresh1 (2583) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 9.04, Build ID DSYT99E o New System Support: Flex System x240 Compute Node (8737, 8738, 7863) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies:
Version 9.03, Build ID DSYT98I o New System Support: HS23E (8038, 8039) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies:
Version 9.02, Build ID DSYT97C o New System Support: iDataPlex dx360 M4 server/2U chassis (7912/7913) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Functional change:
Version 9.01, Build ID DSYT96D o New System Support: x3500 M4 (7383) x3550 M4 (7914) x3650 M4 (7915) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage: o Special usage:
Version 9.00, Build ID DSYT95W o New System Support: BladeCenter HS23 (7875) BladeCenter HX5 (7873, 1910) Flex System x240 Compute Node (8737, 8738, 7863) Flex System Manager Node (8735) x3500 M4 (7383) x3550 M4 (7914) x3630 M4 (7158) x3650 M4 (7915) x3690 X5 (7192, 7147) x3850 X5 / x3950 X5 (7143, 7191) o New server options support: o Problem(s) Fixed: 1. PMR 24817,8QG,000, PMR 30680,499,000 After kicking off DSA on one of the management nodes (x3650 M2) of SONAS 1.2(RHEL5 based), the node became unresponsive and dropped out of the cluster.
2. PMR 53575,000,834, PMR 05961,YL4,760 After running DSA, when using linux dump command on a DDS5 usb internal tape drive attached in x3650M2 backup speed becomes very slowly or failed.
3. PMR 26905,095,866 Running DSA 4.0 as well as DSA 3.4 on x3850 X5 the server is freezing, users have to reboot the server.
4. DSA 4.00 and previous version segmentation fault issue
6. PMR 15086,OTH,760 DSA 9.00 with --no-imm-lan option does not work correctly on RHEL5.3. The USB port state is changed during the execution of DSA.
o Enhancement: o Limitations: o Dependencies: o Functional change: 1. Add GUI and CLI menu for Features on Demand (FoD) Activation Key Management o Special usage:
Version 4.02, Build ID DSYT92I o New System Support: iDataPlex Direct Water Cooled dx360 M4 server o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 4.01, Build ID DSYT92H o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage: - 2011 4Q lifecycle
Version 4.00, Build ID DSYT91S o New System Support: o New server options support: o Problem(s) Fixed: 1. PMR 15065,OTR,760 On Unisys ES7000 or x3850 X5, the Memory Card number with failed DIMM can not be reported in IPMI Eventlog if the Memory Card is bigger than 4.
o Enhancement: o Limitations: o Dependencies: o Functional change: 1. Added > 1TB memory test support o Special usage: - 2011 ToolsCenter 11D
Version 3.48, Build ID DSYT89PUS o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage: - 2011 3Q lifecycle
Version 3.47, Build ID DSYT89LUS o New System Support: x3100 M4 (2582) x3250 M4 (2583) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 3.46, Build ID DSYT89GUS o New System Support: System x iDataPlex dx360 M3 (6391) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 3.45, Build ID DSYT89EUS o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage: - x3850 X5 / x3950 X5 (7143, 7191) EXA scaling
Version 3.43, Build ID DSYT87HUS o New System Support: BladeCenter HX5 (7873,1910) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 3.43, Build ID DSYT87FUS o New System Support: x3850 X5 / x3950 X5 (7143, 7191) x3690 X5 (7192, 7147) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 3.40, Build ID DSYT85T o New System Support: BladeCenter HS22 (1911) x3650 M3 (5454) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Version 3.30, Build ID DSYT80S o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: 1. Correct a problem with LSI MegaRAID reporting for IBM Service o Special usage:
Version 3.20, Build ID DSYT75X o New System Support: x3630 M3 (7377) x3690 X5 (7148, 7149) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: - If you have ServeRAID (M1015) SAS/SATA Controller, 46M0831 installed, you will need one of the following: - uEFI GYE133A or greater for x3200 M3 and x3250 M3 - uEFI Y4E145B or greater for x3400 M2, x3400 M3, x3500 M2 and x3500 M3 - uEFI D6E145C or greater for x3550 M2, x3550 M3, x3650 M2 and x3650 M3 o Functional change: 1. Add LSI Hard Disk Drive (HDD) diagnostic back for both the onboard SAS chip and ServeRAID o Special usage:
Verion 3.20, Build ID DSYT75U o New System Support: x3755 M3 (7164) o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: o Special usage:
Verion 3.10, Build ID DSYT70X o New System Support: x3400 M3(7378, 7379) x3500 M3(7380) x3550 M3 (7944, 4254) x3620 M3 (7376) x3650 M3 (7945, 4255) x3690 X5 (7148, 7149) x3850 X5 Standard Single-node and Multi-node models(7145, 7146) x3950 X5 Specially configured Database Engine models (7145, 7146) iDataplex dx360 M3 (6391) HS22V (7871,1949) HX5 (7872, 1909) o New server options support: Emulex 10Gb/s Fibre Channel over Ethernet Dual Channel Converged Network Adapter(LP21002) Emulex PCI-e Gen2.0 Dual Port 10Gb NIC (49Y4250) 6Gb SSD HBA (46M0912) 6Gb SAS HBA (46M0907) Intel QuadPort Ethernet Server Adapter CFFh Intel Ethernet Daughter Card FCoE SRIOV Key (Ethernet) iSCSI Key (Ethernet) Secure Encryption HBA for 8Gb FC eHBA Emulex Brocade 4Gb FC HBA(59Y1992, 59Y1998) Emulex 2-Port 10Gb Multi-function IO Adapter (CFFh) (49Y4235) Brocade 10Gb Dual-port CNA (42C1820) Broadcom NetXtreme II 1000 Express Quad port Ethernet Adapter (49Y4220) Broadcom NetXtreme II 1000 Express Dual Port Ethernet Adapter (42C1780) MAX5 Memory Expansion Unit o Problem(s) Fixed: o Enhancement: o Limitations: o Dependencies: o Functional change: 1. Add a new option --disable-imm-lan to take down IMM USB Over Lan interface when DSA complete. 2. Added ServeRAID data collection o Limitations: - The following function has been temporarily removed from DSA Preboot for both the onboard SAS chip and ServeRAID: - LSI Hard Disk Drive (HDD) diagnostic o Dependencies: - If you have ServeRAID (M1015) SAS/SATA Controller, 46M0831 installed, you will need one of the following: - uEFI GYE133A or greater for x3200 M3 and x3250 M3 - uEFI Y4E145B or greater for x3400 M2, x3400 M3, x3500 M2 and x3500 M3 - uEFI D6E145C or greater for x3550 M2, x3550 M3, x3650 M2 and x3650 M3 o Special usage:
Version 3.02.56, Build ID DSYT56e o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: - The following systems are supported when BoMC downloads the corresponding system enablement pack: HS22V (7871,1949) x3550 M3 (7944,4254) x3650 M3 (7945,4255) x3400 M3 (7378,7379) x3500 M3 (7839) dx360 M3 (6391) o Limitations: - No HDD diagnostics available - To ensure quality and stability of the DSA code, we have reverted some display functionality of RAID information to what was shown in previous versions of DSA. This affects RAID display on the following adapters: Megaraid 8480 Serveraid MR10i Serveraid MR10is Serveraid MR10m Serveraid MR10k Serveraid M1015 Serveraid M5014 Serveraid M5015 On these adapters, the RAID information is generated from the output of separate command line tools and the format may not match other output in DSA. Dependencies: o Dependencies: o Functional change: o Special usage:
Version 3.00, Build ID: DSYT55a o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: - Added support for Machine Types 7327, 7328, 4251, 4252, 4261 o Limitations: - No HDD diagnostics available o Dependencies: o Functional change: o Special usage:
Version 1.16, Y4YT19AUS o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: - Added support for Machine Types 7839, 7836, 7837 o Limitations: o Dependencies: o Functional change: o Special usage:
Version 1.15, TMYT20AUS o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: - Added support for Machine Types 7321, 6380, 7323 o Limitations: o Dependencies: o Functional change: o Special usage:
Version 1.14, D6YT37AUS o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: - Added support for Machine Types 7946, 4198, 7947, 4199 o Limitations: o Dependencies: o Functional change: o Special usage:
Version 1.13, P9YT48AUS o New System Support: o New server options support: o Problem(s) Fixed: o Enhancement: - Added support for Machine Types 7870, 1936, 7809 o Limitations: o Dependencies: o Functional change: o Special usage:
Version 1.00 - Initial release
(C) Copyright International Business Machines Corporation 2008 - 2012. All rights reserved. ibm_fw_dsa_dsytc5f-9_53_anyos_anycpu_chg
Broadcom NetXtreme I Firmware Update Utility for IBM servers and options using the Broadcom NetXtreme I ethernet adapters.
Version 17.4.4.2a, March 8, 2016
This update package supports the following Broadcom devices: =========================================================== - BCM5717 NetXtreme I LOM - BCM5718 NetXtreme I LOM - BRCM5718 NetXtreme I Gigabit Ethernet Adapter / Product No: 49Y7900 - BCM5719 NetXtreme I LOM - BCM5719 NetXtreme I Gigabit Ethernet Adapter / Product No: 90Y9352 - BCM5720 NetXtreme I Gigabit Ethernet Adapter / Product No: 90Y9370
This update packages updates your Broadcom LOM/Adapter Firmware Code to the levels shown below:
Firmware code: Version Previous ==================== ======== ========== Bootcode for 5717 1.65 1.65 Bootcode for 5717C0 2.10 2.10 Bootcode for 5718 1.65 1.65 Bootcode for 5719 1.43 1.43 Bootcode for 5720 1.39 1.39 iSCSI Boot 18.0.0 18.0.0 EFI Undi 17.4.0* 17.4.0* PXE NX1 17.2.1 17.2.1 NCSI Firmware NX1 1.3.12 1.3.12
Note: An asterisk (*) following a version number represents a certified driver. Arrows (<<) between versions indicate the component has been updated from the previous released software kit.