ServeRAID M5000 Series SAS/SATA Controller Firmware Update

Adapters Supported: ServeRAID M5015 SAS/SATA Controller (46M0829)
ServeRAID M5014 SAS/SATA Controller (46M0916)
ServeRAID M5025 SAS/SATA Controller (46M0830)

NOTE TO SERVICE - Reference RETAIN #N/A

Version 12.15.0-0248
--------------------

Version 12.15.0-0240 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes:
- Fixed issue where JBOD mode would be disabled and would not boot to JBOD drive if one of the VDs is offline (SCGCQ00827731)
- Fixed illegal request sense messages seen repeatedly in FW logs. (SCGCQ00898459)
- Fixed system hangs that could occur due to recoverable errors being marked as unrecoverable (SCGCQ00923692)

Version 12.15.0-0226
---------------

- Fixed an issue where JBOD drives were not reporting the correct drive temperature (SCGCQ00831639)
- Corrected LED behaviour for IBM 6Gb SAS Expander Backplane (SCGCQ00754433)

Version 12.15.0-0199 - Critical
-------------------
Enhancement:
- Display drive speed for 12 GB Seagate hard drives in MSM.
- List battery status in BIOS as N/A for iMR controllers
Fixes:
- Fixed an issue where the ‘cli set securitykey=Lsi@12345’ command fails
with error code 1001 and error message invalid key.
- Fixed an issue where WebBIOS is not displaying correct index position
for boot error handling option.
- Fixed an issue where WebBIOS advanced software option locks the server.

Version 12.13.0-0179 - Critical
-------------------
Enhancement:
- Implemented limited band charging for iBBU08. (RETAIN tip H21631)
- CacheCade 2.0 read and write caching on SSDs is supported on ServeRAID
M5014 and ServeRAID M5015 with the ServeRAID M5000 Series Performance
Accelerator Key.
Fixes
- Fixed an issue in multipath topology to use an alternate IO path if the
current active path is removed.
- Fixed an issue where drive states were marked as online before the
creation of recontruction volumes completed.
- Resolved controller hang condition during system bootup.
- Fixed issue causing iBBU07 to always show "Charging" state
(RETAIN tip H211025)
- Fixed issue causing Virtual Disks to remain in Write-Through state
after a relearn (RETAIN tip H211101)
- Addressed data exposure issue when using CacheCade

Version 12.12.0-0133 - Suggested
-------------------
Fixes:
- Addressed an issue where battery over temperature messages could occur
during charging.
- Fixed issue in the HII broswer where the drive performing copyback
will be stated as replacing and not copyback.
- Fixed issue in the HII browser where the RPM for SATA drives show "0"
- Fixed issue in HII browers where port 4 is shown on both ports 0 and 1
- Fixed HII browser issue where the user will get an error message when a
global hot spare is created.
- Fix HII browser issue where a RAID volume with greater then 3 spans will
fail to create.


Version 12.12.0-0126 - Critical
-------------------
Fixes:
- Fixed a issue where the RAID configuration can be lost when updating
from firmware package 12.0.1-0097 or below.
- Fixed an issue with 4-kilobyte (KB) sector disk support compatibility in
NTFS by disabling 512E drive support mode.

Version 12.12.0-0111 - Suggested
-------------------
Enhancement:
- Support for 512e and 4k SAS/SATA hard drives added
- Implemented limited band charging for iBBU 07.
- CacheCade 2.0 read and write caching on SSDs is supported on ServeRAID
M5014 and ServeRAID M5015 with the ServeRAID M5000 Series Performance
Accelerator Key.
Fixes:
- Set the compatibility bit to 1 so that Patrol reads can be executed on
SSD's
- Fixed an issue where EEPROM init failures are not handled properly
causing the user to see the following message on POST "The native
configuration is no longer supported by the current controller and
firmware."
- Fixed an issue where the controller fails to read the header info from
CFI Flash ROM.
- Resolved issue switching to WT mode for recently failed batteries.

Version 12.12.0-0098 - Suggested
-------------------
Fixes:
- Fixed issue where the battery gauge is not accurate for aged batteries
due to the discharge profiles of aged batteries not matching that of the
new batteries.
- Fixed a issue where a reboot would cause a hot spare to revert to
'Unconfigured Good' state when Performance Accelerator Key is attached.
(RETAIN Tip H204925)

Version 12.12.0-0085 - Suggested
-------------------
Enhancements:
- Prevent non IBM firmware from being flashed on IBM ServeRAID branded
controllers.
- Enabled iBBU08 battery modes.
- ibbu battery will no longer be marked as bad when very high capacity is
detected.
- Dimmer Switch function has been disabled by default.

Fixes:
- Fixed a issue where firmware was taking to long to complete the PCI
config read, causing the system to generate an NMI.
- Fixed issue where enabling security causes the configuration to be missing,
and a configured FDE array to be seen as foreign on reboot.
- Removed BBU mode select from Web BIOS for all controllers.
- Fixed issue where pulling VD 0 from a R60 and rebooting would cause two
foreign configurations.
- Fixed issue where WebBIOS gives unclear message when enabling FDE on an
existing Disk Group.
- Fixed issue where iBBU07 batteries display 65K capacity and are marked SOH
bad.
- Fixed issue where iBBU Absolute Charge is displayed differently
- Fixed issue where the logical Unit ID (VPD page 0x83) changed after
foreign import.
- Fixed issue where the LDBBM entries are incorrect after foreign import.
- Fixed issue where the controller does not work with pci set to nomsi in
kdump kernel.
- Fixed issue where the LED behavior is incorrect, wrong drive will blink
activity.
- Fixed issue where the controller cannot sustain at least 950 MBps
performance with Cache Flush setting one sec.
- Fixed issue where the set properties command fails
- Fixed issue where the iBBU07 battery reported remaining capacity is much
too high (64751 mAh) after a learn cycle.
- Fixed issue where extended retries of write verify commands cause a driver
timeout.
- Fixed issue where the configuration becomes foreign after the firmware
fails multiple attempts to access raid key during boot.
- Fixed firmware issue where a replacement drive is not seen if the
replacement is added during power cycle.
- Fixed a issue where an alert should be sent when one phy connector
between the SAS controller and SAS expander is degraded.
- Enabled puncturing for SATA drives.
- Enabled copy back on SMART.
- Fixed an intermittent RAID key failure during power-on.
- Fixed firmware issue where firmware would cause the controller to
(sles11sp1/rhel6) reset when ‘lspci –vvx’ command is executed.
- Change for iBBU-08 to support firmware Mode5 WB capacity from 960mAh to
674mAh for low power DDR-2
- Fixed a issue where the iBBU battery will not charge while the server
continually resets causing the iBBU battery to over-charge.

Version 12.12.0-0065 - Critical
-------------------
Fixes:
- Fixed issue where the firmware takes too long to complete a PCI Config
Read cycle causing SLES11 to kernel panic.
- Fixed issue where MegaCLI may not be able to change drive or controller
cache setting resulting in a return code of 0x03.
- Added check to return SCSI sense Check condition if PMI is set and LBA
is non Zero for SCSI Read Cap 16
- Fixed issue where a blue screen occurs handling RAID 1 with HSP and medium
errors. The blue screen occurs because the driver times out while the
firmware is retrying sense 0x02. Firmware causes Fatal Error when HSP drive
responded with Sense 0x02 for Write/Verify or TUR
- Change the boot with pinned cache RAID level support which was only allowed
for raid level 0. The check is removed and is allowed for any raid level.
- Fixed hang condition or condition where the uEFI driver does not load due
to the uEFI Driver issuing a command in poll mode to firmware to early
- Remove the following message "Battery cannot initiate transparent learn
cycles" when the iBBU08 is under mode 4 or 5
- Fixed issue where BGI will not disable when a user issues megacli
-LDBI -Dsbl -L0 -a0

Version 12.12.0-0056 - Critical
-------------------
Fixes
- Fixed issue where multi-bit ECC's are not reported during POST
- Lowered the capacity level at which event notifications are generated
for early warning and end of life alerts for iBBU to equal 48 hours

Version 12.12.0-0047 - Critical
-------------------
Fixes:
- Fixed issue where uEFI WebBIOS version may not display the product
name of the second controller
- Fixed issue to prevent users from downleveling firmware to older versions
- Fixed an issue where firmware reports "Unexpected sense, Invalid field
in CDB" for LOG SENSE command sent to Seagate drives
- Fixed issue where SMART failures can take longer then 5 minutes to
report or in some cases fail to report
- Fixed issue where it appears to the user the harddrive cache policy
is changed when requested but the change did not occur
- Fixed issue where a remote iBBU08 will not be seen by the controller
- Fixed data issue When IO is in progress to a RAID 1 array that contains
media errors and is under a rebuild
- Fixed issue where a drive is not marked as foreign during a drive
move between servers causing the import of the configuration to fail
- Fixed issue where the uEFI WebBIOS does not accept the + symbol in
the key code or pass phrase
- Fixed issue for iBBU08

Enhancement:
- Enhancement to Reserve/release call for VCS Symantec configurations
- Enhancements to iBBU event notifications, including the addition of
early warning message.
- Raised the capacity level at which event notifications are generated
for early warning and end of life alerts for iBBUs.

Version 12.12.0-0039 - Critical
-------------------
Fixes:
- Fixed intermittent initialization failure during POST with the
ServeRAID M5025, M5015, and M5014 where the RAID BIOS could fail to
load or the user will see one of the following error messages on
POST:

RAID Adapter Unrecoverable Error!!!
Please check the SDRAM connection.

or

Multi-bit ECC errors were detected on the RAID controller

Version 12.12.0-0037 - Critical
-------------------
Enhancement:
- Add support for iBBU08 (Battery Backup)


Fixes:
- Addressed data issue while reconstructing from RAID1 to RAID0.
- Addressed data issue after power lose to ServeRAID controllers.
- Addressed data issue in some database applications.
- Added fixes from LSI channel products.

Version 12.7.0-0020 - Critical
-------------------
Enhancement:
- Initial release for ServeRAID M5025 SAS/SATA Controller (46M0830)

Fixes:
- Addressed data issue with database applications that use overlapping
read write operating.
- Addressed data issue which may occur during a reconstruction on some
RAID levels that have an associated CacheCade virtual drive enabled.
- Fixed issue where the controller may halt if a drive has medium errors
that are being used in a check consistency, patrol read, or have delayed
writes.

Version 12.0.1-0097 - Critical
-------------------
Fixes:
- Addresses an issue where data becomes inaccessible when drive is
secured after data has been written
.
Version 12.0.1-0096 - Critical
-------------------
Fixes:
- Fixed an issue where the BBU may not be seen on POST.
- Fixed an issue where the firmware doesn't follow the spinupdelay
and maxtargetspinup values set in NVDATA causing spin up of all
the drives a at the same time.
- Fixed a very intermittent issue where the RAID key (M5000)
authentication may not occur on boot leaving users without key
options.
- Addressed a very rare issue with the expander devices where the
firmware megamon could occur if the sgpio configuration cable has
errors.

Version 12.0.1-0090 - critical
-------------------
Fixes:
- Fixed issue where controller properties such as Rebuild, CC, and
BGI are not changing when up and down arrow keys are used.
- Fixed issue on x3950 M3 servers that can cause a system hang at
reboot

Version 12.0.1-0084 - Non-critical
-------------------
Enhancement:
- Support added for the ServeRAID M5000 Series Advanced Feature Key.


Version 12.0.1-0064
-------------------
- Initial release
ibm_fw_sraidmr_m5000-12_15_0-0248_linux_32-64_chg

Firmware Update for IBM High IOPS Modular Adapter

Controller Supported:
- IBM 300 GB High IOPS MLC Modular Adapter (90Y4361)
- IBM 600 GB High IOPS MLC Modular Adapter (90Y4365)
- IBM 800 GB High IOPS MLC Modular Adapter (90Y4369)
- IBM 300 GB High IOPS SLC Modular Adapter (90Y4373)


Version 7.30.05.00-1 - Non Critical
--------------------
- Added Support in RHEL 5.9 indistro device driver

Version 7.30.05.00 - Initial release
-------------
ibm_fw_mpt2sas_hiop-7_30_05_00-1_linux_x86-64_chg

ServeRAID M1000 Series SAS/SATA Controller Firmware Update

Adapters Supported: ServeRAID M1115 SAS/SATA Controller for IBM System X (81Y4448)
ServeRAID M1015 SAS/SATA Controller (46M0831)

Version 20.13.1-0254
--------------------

Version 20.13.1-0252 - Moderate Impact/Low Probability of Occurrence
---------------------
Fixes:
Fixed issue where wrong drive connector information (connector: null x0) shows in MSM (SCGCQ00996578)
Fixed issue where firmware hit assertion while booting with 4K PDs. (SCGCQ00944388)
Fixed system hangs that could occur due to recoverable errors being marked as unrecoverable (SCGCQ00923692)
Fixed issue where exception would occur during foreign import while importing number of VDs greater than supported count (SCGCQ00931011)


Version 20.13.1-0245 - Moderate Impact/Low Probability of Occurrence
---------------------
- Fixed an issue where virtual drivers become inconsistent after the system an AC failure. (SCGCQ00897229)
- Fixed an issue where Illegal request sense messages are seen repeatedly in FW logs due to attempts to collect temperaure for pds which does not support page (0x2F) at every smart poll interval. (SCGCQ00898459)
- Fixed an issue where command "cli set securitykey=Lsi@12345" fails with error code "1001" and error message "invalid key".
- Added a warning message when preboot configuration utility is Disabled but the user tries to launch it. (SCGCQ00662761)
- Fixed an issue where WebBIOS Advance software option menu from main page could hang the system. (SCGCQ00683327)
- Updated the drive speed display string to support 12Gb/s (SCGCQ00751036)
- Corrected inconsistency in size showing in for total capacity property between webBIOS and MSM (SCGCQ00752176)


Version 20.13.1-0200 - Critical
-------------------
Enhancement:
- Display drive speed for 12 GB Seagate hard drives in MSM.
- List battery status in BIOS as N/A for iMR controllers
Fixes:
- Fixed an issue where the ‘cli set securitykey=Lsi@12345’ command fails
with error code 1001 and error message invalid key.
- Fixed an issue where WebBIOS advanced software option locks the server.
- Changed patrol read completion time calculation to include time for
associated IO operations.
- Fixed SGPIOs signal issue.

Version 20.11.1-0184 - Suggested
-------------------
Fixes:
- Updated SBR to avoid an errata that could cause correctable CPU errors
on some systems.
- Fixed an issue where NULL events may show in event log, preventing
capture of controller event logs.

Version 20.11.1-0137 - Suggested
-------------------
Enhancement(s):
- Update recovery mode page (WriteRetryCount and recoveryTimeLimit) during
discovery of a drive and during spinup recovery when sense 6/29 is
received.

Fixes:
- Fixed an issue where certain drives were reporting a temperature of 65
degrees Celsius.
- Fixed an issue where systems with SSD HDD will pop up an error message
after creating a virtual drive via HII on M1115.
- Fixed an issue where the drive state is not modified when a recon
virtual drive is created from the reboot path.

Version 20.10.1-0107 - Suggested
-------------------
Fixes:
- Fixed grammatical errors in WebBIOS.
- Fixed an issue in WebBIOS Drive Group Definition screen where enclosures
should not be selectable in the Drives column.
- Fixed an issue in uEFI-WebBIOS where the white bars do not match up under
VD properties page.
- Fixed an HII browser issue where a drive performing a copyback displayed
the state as "Replacing" but other utilities showed the state as copyback.
- Fixed an HII browser display issue where SATA drives showed "0" for the
value of RPM under drive properties.
- Fixed a display issue where the HDD port number showed incorrectly in an
HII browser.
- Fixed an HII browser issues where creating a global hotspare gave the
user an error message.
- Fixed an HII browser issue when security is changed with local key
management the changing security report current mode is disabled as
external keu management.
- Fixed an HII browser issue where the user got the following error message,
"The request command has invalid arguments," when changing the security
key report.
- Fixed an HII browser issue where the user was unable to save the
configuration after adding an extra span during array creation.
- Fixed an HII browser issue where the return value was not correct when
the browser called extract config with a result of null.


Version 20.10.1-0101 - Suggested
-------------------
Fixes:
- Fixed an issue where a system uefi error will occur when the
bootTargetId is set to 0.
- Fixed a problem where the firmware will allocate the sata bbl entry for
the drive when moved from unsupported to supported.
- Fixed a firmware issue where the TargetId for the recon LD should be set
to its original LD.
- Fixed a HII error message "Question Value mismatch with Option value!"
after selecting factory defaults in HII.
- Fixed an issue where the firmware fails to create the configuration and
utilities fail to report the VD size after the reconstruction.

Version 20.10.1-0091-01 - Non-Critical
-------------------
Fix
- Fixed issue where update may fail to find all supported controllers
in SLES 11 SP 2.
Note not change in the firmware; it is the same as package 20.10.1-0091.

Version 20.10.1-0091 - Suggested
-------------------
Enhancement:
- Add support for ServeRAID M1115

Fixes:
- Fixed issue where after starting a reconstruction on a RAID 0 the
progress %, does not increase.
- Fixed an issue where a new drive, inserted after a drive failure, goes
to JBOD and not auto rebuild.
- Fixed physical drive count issue that stated more than (16) devices
already exists

Version 20.10.1-0069- Suggested
-------------------
Enhancement:
- ServeRAID M1015 Dimmer Switches are disabled by default.

Fixes:
- Fixed issue where enabling security causes the configuration to be
missing, and a configured FDE array to be seen as foreign on reboot.
- Fixed issue where WebBIOS gives garbled message when enabing FDE on
an existing Disk Group
- Fixed issue where the logical Unit ID (VPD page 0x83) changed after
foreign import.
- Fixed issue where the LDBBM entries are incorrect after foreign import.
- Fixed a problem where firmware was taking to long to complete the PCI
config read. Causing the system to generate an NMI.
- Fixed issue where the controller does not work with pci set to nomsi in
kdump kernel.
- Fixed issue where the LED behavior is incorrect, wrong drive will blink
activity.
- Fixed issue where the configuration becomes foreign after the firmware
fails multiple attempts to access raid key during boot.
- Fixed firmware issue where a replacement drive is not seen if the
replacement is added during power cycle.
- Fixed an intermittent RAID key failure during power-on.

Version 20.10.1-0052- Critical
-------------------
Enhancement:
- Add support to pass SMART errors for JBOD drives to MSM

Fixes:
- Added check to return SCSI sense Check condition if PMI is set and
LBA is non zero for SCSI Read Cap 16.
- Fixed issue where a bluescreen occurs handling RAID 1 with HSP and
medium errors. The bluescreen occurs becausethe driver timesout
while fw is retrying sense 0x02. Firmware causes Fatal Error when HSP
drive responded with Sense 0x02 for Write/Verify or TUR
- Fixed hang condition or condition where the uEFI driver does not load
due to the uEFI Driver issuing a command in poll mode to firmware to
early

Version 20.10.1-0045 - Critical
-------------------
Fix:
- Fixed issue where firmware has incomplete writes during power fail and
recovery

Version 20.10.1-0036 - Critical
-------------------
Fixes:
- Fixed issue where uEFI WebBIOS version may not display the product
name of the second controller
- Fixed issue to prevent users to downlevel firmware to older versions
- Fixed an issue where firmware reports "Unexpected sense, Invalid
field in CDB" for LOG SENSE command sent to Seagate drives
- Fixed issue where SMART failures can take longer then 5 minutes to
report or in some cases fail to report
- Fixed issue where it appears to the user the harddrive cache
policy is changed when requested but the change did not occur

Version 20.10.1-0022 - Critical
-------------------
- Fixed issue where Windows 2008 R2 WS08 cannot be installed properly
on ServeRAID M1015 SATA JBOD with a uEFI boot.
- Added warning message when user tried to change more then 16 drives
to JBOD.
- Addressed a problem where direct attached drives are given incorrect
slot numbers
- Added fixes from LSI channel products.
- Fixed issue where a single JBOD drive will not boot after a Windows
2008 R2 installation.

Version 20.5.1-0014 - Critical
-------------------
- Addressed data issue with database applications that use overlapping
read write operating.
- Addressed data issue which may occur during a reconstruction on some
RAID levels that have an associated CacheCade virtual drive enabled.
- Fixed problem where the controller may halt if a drive has medium
errors that are being used in a check consistency, patrol read, or
have delayed writes.

Version 20.1.1-0059 - Critical
-------------------
Fixes:
- Fixed an issue where a physical drive that is changed to JBOD from
powersave will become unconfigured good again
- Addresses an issue where data becomes inaccessible when a drive is
secured after data has been written


Version 20.1.1-0049 - Suggested
-------------------
Enhancement
- Support M1000 key for RAID 5 and SED support

Fixes:
- Fixed an issue in M3950M3 where webbios would hang
- Fixed an issue where the controller properties in WebBIOS such as
Rebuild, CC and BGI are not changing when we use up and down arrow
keys.
- Fixed an issue where Enclosure ID's are not being shown in MSM

Version 20.1.1-0046 - Suggested
-------------------
- Enabled support for the ServeRAID M1000 Series Advanced Feature Key.

Note: All Logical Drives must previously have the encryption enabled
before data is written on to the SED drives. Please read Retain TIP
H123152 for more details.

Version 20.1.1-0042
-------------------
- Initial release
ibm_fw_sraidmr_1000-20_13_1-0254_linux_32-64_chg

ServeRAID 6GB SAS/SATA Controller Firmware Update

Adapters Supported: ServeRAID M5110 SAS/SATA Controller for IBM System x (81Y4481)
ServeRAID M5110e SAS/SATA Controller for IBM System x
ServeRAID M5120 SAS/SATA Controller for IBM System x (81Y4478)
ServeRAID M5016 SAS/SATA Controller for IBM System x (90Y4304)
ServeRAID M5115 SAS/SATA Controller for IBM Flex System (90Y4390)
ServeRAID M5016 SAS/SATA Controller for IBM System x (90Y4304)

NOTE TO SERVICE - Reference RETAIN #N/A

Version 23.34.0-0018
--------------------

Version 23.34.0-0009 - High Impact/High Probability of Occurrence
--------------------
FW Package: 23.24.0-0009

HII: 03.17.14.02

UEFI Driver: 0x06110200

BIOS: 5.50.03.0

MR FW: 3.460.35-6104

iMR FW: 3.460.34-6103


Fixes:

- Fixed the potential of a data miscompare that was observed only at a vendor test facility under very heavy IO and abnormal practices (SCGCQ00995594, Port of SCGCQ00976904)

- Fixed an issue where error "Controller encountered fatal error and was reset" may occur under heavy IO and background operations (SCGCQ00894643)

- Fixed an issue where VMWare may crash when a Guest Operating System is powered off (SCGCQ00872121, Port of SCGCQ00854914)

- Fixed an issue where write-verify performance was lower than expected (SCGCQ00858151, SCGCQ00874193)

- Fixed an issue where "I2C 4 PID 10 SCL STUCK Low! while I2C Rx receiving data intStatus 00008000" may appear in firmware log (SCGCQ01007592)

- Fixed an issue where the Measured Voltage instead of Charging Voltage was displayed in event log (SCGCQ00876489)

- Fixed an issue where Supercap "Battery Not Present" error may occur after shutdown or reboot during a learn cycle (SCGCQ00917115)

- Fixed an issue where Write-through and Write-back cache policies can be changed via Windows Logical Disk Properties. (SCGCQ00856979)

- Fixed an issue where enclosures may go missing when connected in daisy-chain after multiple expander reset cycles (SCGCQ00840725, Port of SCGCQ00818569)

- Fixed an issue where MegaRAID Storage Mananger may display an error message if 'Schedule Consistency Check' is selected. (SCGCQ00852649, Port of SCGCQ00832908)

- Fixed an issue where Patrol Read Properties window does not pop up on MegaRAID Storage Manager (SCGCQ00862478, Port of SCGCQ00797676)

- Fixed an issue where MegaRAID Storage Manager shows messages with Error code 240 and no description (SCGCQ00970948, Port of SCGCQ00904466)

- Fixed an issue where Amber LED may turn on erroneously when an enclosure's slot numbers start with 0 but bay numbers start with 1 (SCGCQ01019622, Port of SCGCQ00903181)

- Fixed an issue where the Generic RAID1 profile option in HII is not greyed-out after creating 64 Virtual Drives (SCGCQ00826822, Port of SCGCQ00816137)

- Fixed an issue where firmware may hang until system is reset (SCGCQ00928869, Port of SCGCQ00923286)

- Fixed an issue where a Virtual Drive may disappear on reboot if it was created with drives from a previously-erased Virtual Drive (SCGCQ00937912, Port of SCGCQ00900237)

- Fixed an issue where Functional Level Reset was not supported (SCGCQ00854343, Port of SCGCQ00840253)

- Fixed an issue where an "L2 unrecoverable cache error" may occur when modifying Patrol read properties (SCGCQ00854668, Port of SCGCQ00847162)

- Fixed an issue where a Hot Spare disk may become Unconfigured Good on reboot (SCGCQ00862477, Port of SCGCQ00803341)

- Fixed an issue where SafeID may change on repeated queries using StorCLI (SCGCQ00949550, Port of SCGCQ00941577)

- Fixed an issue where error "MonTask: line 1272 in file ../../raid/1078dma.c" may occur while running IO in Virtual Machines (SCGCQ01016071, Port of SCGCQ00822403)

- Fixed an issue where incorrect connector information "connector: null x0" shows in MegaRAID Storage Manager (SCGCQ01016040, Port of SCGCQ00996578)

- Fixed an issue where a concurrent Consistency Check cannot be started after resetting adapter to factory defaults (SCGCQ00839437, Port of SCGCQ00838830)

- Fixed an issue where JBOD mode may be disabled if a Virtual Drives is offline (SCGCQ00871662, Port of SCGCQ00827731)



Enhancements:

- Added protection for clearing Foreign Configuration if preserved cache exists (SCGCQ00880783, Port of SCGCQ00842327)

- Enhanced cache restore operation for when restore data size is different than cache size (SCGCQ00860303, Port of SCGCQ00855038)

Version 23.33.0-0044
--------------------

Version 23.33.0-0043 - High Impact/High Probability of Occurrence
-----------
Fixes:
- Fixed an issue where hard drive slot amber LED not functioning correctly.
- Fixed an issue in iMR mode where "Controller encountered fatal error and was reset" errors
can occur under heavy IOs and background operations (SCGCQ00894643) (RETAIN Tip H001154)
- Fixed an issue where BBU status says optimal but firmware logs indicate that the BBU has
failed (SCGCQ00838052) (RETAIN Tip H214857)
- Fixed an issue where importing a foreign configuration may fail after reconstruction on 4k
sector drives (SCGCQ00830109)
- Fixed an issue where the firmware may allow the OS to change VD cache settings
(SCGCQ00842350)
- Fixed an issue where MR firmware reports "no SMART" error when attaching a PFA drive
(SCGCQ00839455)
- Fixed an issue where the firmware may hang (enter MonTask) when a guest OS is powered on or
off in VMWare (SCGCQ00854914)
- Fixed an issue where setting the learn cycle property of iBBU09 gives an I2C error
(SCGCQ00831315)
- Fixed an issue where "Prepare for Removal" does not work on a PD when drive erase is in
progress (SCGCQ00811219)
- Fixed an issue where MSM displays "The requested command has invalid arguments" error
message if 'Schedule Consistency Check' is selected (SCGCQ00852649)
- Fixed an issue where cache memory size in iMR is not showing 0 (SCGCQ00838893)
- Fixed an issue where an incorrect MFI_STAT_PD_TYPE_WRONG error is returned by the firmware
when PDs with different block size are mixed (SCGCQ00840251)
- Fixed an issue where the controller reports cache memory size as 0 when no logical drives
are present (SCGCQ00837600)
- Fixed an issue where concurrent consistency check cannot be started after issuing
"setfactorydefaults" command (SCGCQ00839437)
- Fixed an issue where uEFI may report LSI EFI driver "Unhealthy" or "Failed" when more than
64VDs are configured (SCGCQ00831006)
- Fixed an issue where functional level reset was not properly showing as unsupported
(SCGCQ00854343)
- Fixed an issue where the legacy CTRL-H utility may report the wrong PCIe slot number
(SCGCQ00799339)
- Fixed an issue where the legacy OpROM may show an expander as a JBOD drive in POST
(SCGCQ00809682)
- Fixed an issue where an encrypted JBOD may be presented to the system in encrypted form even
though password was entered incorrectly (SCGCQ00808086)

Enhancements:
- Added ability to determine SuperCap revision ID when VPD is not programmed (SCGCQ00828990)
- Added support for SES RQST_OK deassertion for customer proprietary JBOD SEP (SCGCQ00834321)
- Added feature to enable support for detecting CPLD code version (SCGCQ00840631)
- Added feature to enable drive fault LED to be lit when a known-bad drive is connected to the
controller (SCGCQ00858142)
- Added feature to turn on drive Fault LED when the controller detects a drive that was
previously marked Bad (SCGCQ00858140)


Version 23.33.0-0018 - High Impact/High Probability of Occurrence
-----------
Fixes:
- Incorporated MegaRAID FW stack 5.13
- Fixed an issue where drive temperature cannot be displayed for a drive in Failed or Foreign state (SCGCQ00693959)
- Fixed an issue where after creating an LD via StorCLI or MSM the firmware writes into saved power condition mode page (0x1a) of all PDs in the LD and enables their idle timers (SCGCQ00658701)
- Fixed an issue where Patrol Read would sporadically correct the same defective LBA repeatedly (SCGCQ00729591)
- Fixed an issue where importing a Foreign array onto a new controller may fail with "Cannot force emulate VD to 512E since enable512Esupport is false" error in firmware log (SCGCQ00721106)
- Fixed an issue where the controller may enter MegaMon sporadically (SCGCQ00776409)
- Fixed an issue where MSM may not report a Full Initialization Aborted error until system rebooted (SCGCQ00759100)
- Fixed an issue where the firmware may allow the OS to change VD cache settings (SCGCQ00842350)
- Fixed an issue where Link Speed may show UNKNOWN when attaching a 3G or 6G SATA drive (SCGCQ00803522)
- Fixed an issue where StorLib may return 0x00ff (fail) code even though operation succeeds when creating a VD out of an existing drive group (SCGCQ00827685)
- Fixed an issue where format process of SSD may take much longer than in previous firmware (SCGCQ00674388)
- Fixed an issue where controller must have cleared config to enable 240VD unless existing config only included single-drive RAID0 VDs (SCGCQ00559643)
- Fixed an issue where some commands would timeout with CDB=ff ff ff ff (SCGCQ00459760)
- Fixed an issue where slot ordering in iMR mode might differ from slot numbering in MR mode (SCGCQ00559274)
- Blocked CacheCade deletion when multiple CacheCade volumes are associated with Virtual Drives, preventing data issues (SCGCQ00830977) (RETAIN TIP H214323)

Features/enhancements:
- Added support for 512e drives (SCGCQ00425363)
Enhanced Event Log to include CVPM health details after every Learn Cycle to allow closer monitoring of CVPM health (SCGCQ00819877)
- Implemented a retry for reads of CVPM data to avoid erroneous event 386 or 150 in the Event Log (SCGCQ00392439)
- Added ability for firmware to report the temperature for all SAS/SATA HDD/SSD (SCGCQ00490819)
- Implemented ability for firmware to read drive temperature immediately following SAS discovery (SCGCQ00602573)
- Added ability to clear the MaintainPdFailHistory (SCGCQ00474559)


Version 23.29.0-0015 - Critical
-------------------
Enhancement
- Provide mechanism to disable PCIe backchannel training via SBR.
Fixes:
- Fixed an issue where the ‘cli set securitykey=Lsi@12345’ command fails
with error code 1001 and error message invalid key.
- Fixed an issue where foreign configuration import could fail.
- Fixed an issue where storcli.exe /c0 show all command repeatedly prints to
termlog with respect to upgradekey presence.
- Fixed an issue where boot message ‘cached data was lost,’ even when there was
no battery present.
- Fixed an issue where the order of the first 64 VDs in the POST is not the
same sequence as returned from the firmware.
- Fixed storCLI adpfwflash option crash and adpallinfo option failure.
- Reduced the bootblock Init time, which effectively reduces the configuration
retry time to approximately 700 mS.

Version 23.22.0-0024 - Non-Critical
-------------------
Enhancement(s):
- Display the Native Command Queuing (NCQ) enabled/disabled status of every
SATA disk drive in the output of StorCLI and MegaCLI.
- Added support for ServeRAID M5100 Series 2GB Flash/RAID 5.
Fix(es):
- Disable PI CRC checking when the drive is not initialized during a CC.
- Increased the SuperCap learn time out value for 2GB TMM-B solution.
- Fixed an issue for 2GB memory modules where SuperCap does not get connected
to the controller and hence cache offload fails.
- Fixed an issue where cache policy of virtual drives(VD) does not change to
write through(WT) mode even after detecting a bad supercap.
- Fixed an issue where a RAID configuration created with physical disks in
powersave mode could be lost after rebooting the system.
- Fixed an issue where an invalid frame sent during a PIO-mode SATA passthrough
command results in resetting the drive.
- Fixed an issue where the system is not allocating memory correctly when MR
and iMR controllers are in the same system.
- Fixed an issue where deep learn does not start immediately when the relative
state of charge (RSOC) is just equal to 95%.
- Fixed an issue where performing a re-key operation in external key management
(EKM) mode without doing a reboot, and then switching to local key management
Mode(LKM) results in the Firmware logs showing that a drive security key
was created but HII says the key is incorrect.
- Fixed an issue where on a local key management (LKM) enabled controller, the
user is asked to enter the security key to unlock and
import a foreign drive, which is locked and has external key management
(EKM) enabled.

Version 23.16.0-0027 - Critical
-------------------
Fix(es):
- Addressed data exposure issue when using CacheCade
- Fixed issue where Supercap shows 0 Capacitance
- Fixed iBBU09 battery issue that caused a VD cache policy to remain in
write-through mode after a manual relearn
- Fixed iBBU09 battery issue that caused a VD cache policy to periodically
toggle between write-back/write-through mode
- The limits for iBBU09 battery charging were not updating properly in a
learn cycle
- Ensures a single supercap pack is not supported on 2GB memory module.
- Resolves a firmware crash seen while doing continuous sas cable pulls.
- Ensures OpROM loads even if segment address is 0xC0000.
- Fixed an issue where the adapter is running iMR machine checking after
requesting host memory.
- Fixed an issue where HII does not allow the user to make use of the remaining
free capacity to configure additional VD for R50/R10.
- Fixed an issue where an HII: empty warning prompt is given when creating a
CacheCade VD with forced writeback option.
- Fixed and issue where Windows cannot install without a VGA device on board.
- Fixed and issue in EFI WebBIOS were consistency check is still shown in
progress after 1 PD is removed from a R1 array.

Version 23.16.0-0018 - Suggested
-------------------
Fix(es):
- Fixed an issue where the adapter is running iMR machine checking after
requesting host memory.
- Fixed an issue where HII does not allow the user to make use of the remaining
free capacity to configure additional VD for R50/R10.
- Fixed an issue where an HII: empty warning prompt is given when creating a
CacheCade VD with forced writeback option.
- Fixed and issue where Windows cannot install without a VGA device on board.
- Fixed and issue in EFI WebBIOS were consistency check is still shown in
progress after 1 PD is removed from a R1 array.

Version 23.12.0-0016 - Suggested
-------------------
Fix(es):
- Added isync to prevent speculative execution while memory is being allocated.
- Delayed enablement of POM until AFTER valid memory range is provided by host
system.

Version 23.12.0-0011 - Suggested
-------------------
Enhancement(s):
- Support for 512e and 4k SAS/SATA hard drives added
- Implemented Limited Band Charging for iBBU09 (RETAIN tip H21631)
- Changed BIOS check to determine if running in HAMR, in order to ensure nothing
gets broken when user has an iButton which is not programmed.
- Changed controller status for safe mode to show controller status as safe mode
and disable debug message logging in serial port.

Fix(es):
- Addressed an issue where deeply discharged Cache Vault Power Modules would be
prematurely be marked as failed.
- Fixed an issue where HII hangs when trying to enter configuration
management while in safe mode. Changed the safe mode warning message as below:
"Controller is running in safe mode. Safe mode is used for diagnostic purposes
only. Limited operations such as Configuration Preview, Clear Configuration
and View/Change Controller Properties are allowed in this mode. Other
operations such as Create Configuration, Import and Clear Foreign
Configurations are not allowed. To exit safe mode, correct the fault, and
reboot your computer."
- Fixed an issue where having more than three adapters results in a
calculation error for the offset to store physical disk info for fourth adapter,
due to BIOS not clearing upper byte of AX (that is AH which is containing
some non zero value).
- Fixed an issue where the Wrong spanned drive group size is displayed
by WebBIOS (Ctrl-H).

Version 23.7.1-0010 - Suggested
-------------------
Fixes:
- Fix an issue related to the where the TSOC (EEPROM) is not able to read
or write from the firmware which will result in the message "Incompatible
secondary iButton present."
- Fix a HII broswer issue where Cachecade virtual drive can be selected as
a boot device.
- Fix a HII broswer issue where the user is unable to clear the controller
configuration when there are no drives attached.
- Fix an issue where the BIOS doesn't display the RAID level and VD size
correctly at BIOS POST.

Version 23.7.1-0009 - Suggested
-------------------
Fixes:
- Fixed an issue where SoH is bad after a learn cycle but iBBUI shows good
status.
- Fixed an issue where hi-temp warning was not being displayed.

Version 23.7.0-0037 - Suggested
-------------------
Fixes:
- Corrected differential signals for Phys 2 and 3 that caused slot numbers in
simple swap configurations to be incorrect.
- Fixed an issue when 'maintain PD failed history' is enabled, and a cable is
removed while a drive is added, the drives state goes to optimal instead of
foreign unconfigured bad.
- Fixed a problem where a capacity change is reported after a rebuild
completes on a Cache Cade volume.
- Fixed a controller firmware hang when the recovery of a medium error takes
to long.
- Fixed an issue where the SATA BBM (Bad Block Manager) list was being
corrupted.
- Fixed an issue where FoD (Feature on Demand) Options were being lost because
of errors while accessing the TSOC.
- Fixed a problem where the controller firmware would crash and drives would
go offline when a bad block entry was created during a check consistency
operation.
- Fixed a problem where drives were being marked unconfigured bad (foreign)
on reboot.
- Fixed problem where a member of a CacheCade volume did not get marked as
foreign when the drive was pulled with 'maintain PD failed history' enabled.
- Fixed a problem where during a rebuild, a former hot spare that was now in
a state of unconfigured good, moved back to the state hot spare, which then
automatically started a copyback operation, causing the rebuild to restart.
- Fixed a problem where a controller fault occurred during a reboot while a
physical device was in progress of a PD Erase.

Version 23.7.0-0029 - Suggested
-------------------
Enhancements:
- Added support for Cache Cade 2.1
- Added Support for PI Drives

Fixes:
- Fixed an issue where the firmware reports device initialization completion
status to be greater than 100% at startup.
- Fix an issue where when a secure foreign drive was present, VD creation
fails because firmware becomes unresponsive
- Added a check for the presence of PD before writing the data arms of a
protected LD during BGI.
- Fixed Firmware asserts in CacheMemAllocForPrebootApps() when memory was
allocated twice by BIOS.
- Fixed an issue with USB Cacheoffload restore fails after multiple power
cycles onServeRAID M51xx controllers.
- Fixed an issue where querying SMART / PFA Status returns "all zeros" in Sense Data.
- Fixed an issue where the import of a config from MR to iMR resulted in a firmware crash.
- Fixed an issue where iMR firmware crashed while creating 8/16/32 KB stripe size Lds.
- Fixed background initialization watermark conversion to PD LBA.
- Fixed write protected R1E data arms during initialization.
- Fixed an issue where MR firmware crashed while discarding pinned cache.
- Fixed an issue where a dirty LD dependency information of SSD pd has stale entries.
- Corrected an issue during system booting from pinned cache, firmware goes
to loop message BootMsgDcmd
- Fixed an issue where a BGI was aborted and restarted, elapsed time was not reset.
- Fixed an issue where the start ref for a shared cache line was not an
indicator of the offset into the stripe.
- Fixed an issue where the firmware hangs while running CC on a rebuilt R1 VD with SBBM.
- Fixed an issue where the firmware was wrongly adding puncture entries.
- Fixed an issue where rebuild was ran twice on a target drive with 100% full SBBM table.
- Fixed an issue where the firmware was generating powersave change event when DS3 was not enabled, due to this application are not parsing the event.
- Fixed an issue where recon from R0 to R1 using 3 TB drive causes firmware to report excessive unexpected sense events.
- Fixed an issue, in which the bbuMode would revert to the factory default value of 5, when automatic learn cycle was enabled.
- Fixed an issue where cache offload firmware reports unnecessary High Temp Event due to incorrect temp value.
- Fixed an issue in which a Patrol Read may not start under certain conditions.
- Fixed an issue where the firmware hits montask after discarding the cache when a snapshot VD was involved.
- Fixed an issue where the firmware hangs during pin cache destage as dirty lines in that map never become zero.
- Fixed an issue where CC fails to correct media error at 2TB location on 2 3TB SATA drives that support WU.
- Fixed an issue where a new XML file was added to the nvdata, the buffer to hold the uncompressed nvdata overflowed.
- Fixed an issue where an imported drive becomes unconfigured good when secure VD erase was running.
- Fixed an issue where CC stops progressing on a R6 VD with media errors.
- Fixed an issue where 3TB Hitachi HDD failed in immunity test (Electrostatic Noise test).
- Fixed an issue where controller features are lost if RAID Key was not detected.
- Fixed an issue where performance degraded in RAID 5 Sequential Writes due to command Out-of Ordering.
- Fixed an issue where "Native configuration is no longer supported" message in post.
- Fixed an issue where (DDR3) Initialization fails with fault 0x91a1 - initial DFIRL selected too low.
- Fixed an issue where subsequent drives are dropped when all drives in the
stagger spin up drives fails on boot sequence.

Version 23.2.1-0043 - Suggested
-------------------
Fixes:
- Fixed an issue where "Potential non-optimal configuration due to drive PD commissioned as emergency spare" alarm would trigger erroneously.
- Fixed an issue where Copyback does not progress upon inserting drives.
- Fixed an issue When allowMixInLD is Disabled, and causes Copyback Fails after Rebuild to Emergency Hot Spare.
- Fixed an issue where the Firmware faults while flashing.
- Fixed an issure where querying SMART / PFA Status to Return all zeros in Sense Data.
- Fixed an issue where the Re-inserted Drives becomes Unconfigured_good causing auto rebuilds to fail to start.

Version 23.2.1-0033
-------------------
- Initial release
ibm_fw_sraidmr_6gb-23_34_0-0018_linux_32-64_chg

IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.23.00 Build ID: IBM12300
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.23.00
- Update Utility release for IBM x86 servers.

Note 1: *- Add Lenovo Branded Part Number in supporting list

Note 2: *- Remove the legacy HDD/SSD in this Update program, the drives
were out of production by 4Q2014 or no firmware changes since 1Q2014.
There is a seperate update program to support these drives.


This package acknowledges support and may include updates for
drives with product ID strings of:

SAS 3.5"

- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to LC5H - See Note 1* above

- ST2000NM0043, ST4000NM0043 to FC5D - See Note 1* above

- ST2000NM0054, ST4000NM0054, ST6000NM0054 to FC6D - See Note 1 * above

- ST3300657SS, ST3600057SS to LA5A - See Note 1* above

- HUS724020ALS64, HUS724030ALS64, HUS724040ALS64 to K3LC - See Note 1 * above

- HUS724020ALS61, HUS724040ALS61 to P3LC - See Note 1* above

- WD1001FYYG-23S, WD2001FYYG-23S to XA39 - See Note 1 * above

- WD5003ABYX-23 to WC42 - See Note 1 * above

- ST1000NM0045, ST2000NM0045, ST4000NM0025 to LK84 - See Note 1* above

- ST6000NM0095 to LC84 - See Note 1* above

- MG04SCA60EE to TG45 - See Note 1* above

- ST2000NM0034, ST4000NM0034, ST6000NM0034 to BC6F





SAS 2.5"

- ST300MM0006, ST600MM0006, ST900MM0006 to L56R - See Note 1* above

- ST300MM0026, ST600MM0026, ST900MM0026 to F56F - See Note 1* above

- ST1200MM0007 to L57D - See Note 1* above

- ST1200MM0017 to F578 - See Note 1* above

- ST300MP0005, ST600MP0005 to L67J - See Note 1* above

- ST300MP0015 to F674 - See Note 1 * above

- ST9146853SS, ST9300653SS to L63M - See Note 1* above

- ST9500620SS, ST91000640SS to LD2L - See Note 1* above

- HUC156030CSS20, HUC156060CSS20 to K2GF - See Note 1* above

- HUC109030CSS60, HUC109060CSS60, HUC109090CSS60 to K2EK - See Note 1* above

- HUC109030CSS61, HUC109060CSS61, HUC109090CSS61 to P2EK - See Note 1* above

- AL13SEB300, AL13SEB600, AL13SEB900 to TB37 - See Note 1* above

- HUSMM1620ASS20, HUSMM1640ASS20, HUSMM1680ASS20, HUSMM1616ASS20 to K4CC - See
Note 1* above

- HUSMM1640ASS20E, HUSMM1680ASS20E to P4CC - See Note 1* above

- ST1000NX0453 to LD48 - See Note 1* above

- HUC101860CSS20, HUC101890CSS20, HUC101812CSS20, HUC101830CSS20 to K2H9 - See
Note 1* above

- HUC101860CSS20E, HUC101890CSS20E, HUC101812CSS20E, HUC101830CSS20E to P2H5 -
See Note 1* above

- HUC101818CS420 to J5H9 - See Note 1* above

- HUC101818CS420E to N5H9 - See Note 1 * above

- ST1800MM0018 to L59B - See Note 1* above

- ST1800MM0068 to F594 - See Note 1* above

- AL14SEB180E to TL43 - See Note 1 * above

- USMR1625ASS20E to P4C9 - See Note 1* above



SATA 3.5"

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to LB5F - See
Note 1* above

- WD1004FBYZ-23YC, WD2004FBYZ-23YC to WH03 - See Note 1 * above

- ST1000NM0055, ST2000NM0055, ST4000NM0035 to LJ84 - See Note 1* above

- ST6000NM0115 to LB83 - See Note 1* above

- MG04ACA600E to TJ42 - See Note 1* above


SATA 2.5"

- ST9250610NS, ST9500620NS, ST91000640NS to LE2B - See Note 1* above

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB to MC50 - See
Note 1* above

- SSDSC2BB800G4I to D201NE40 - See Note 1* above

- ST1000NX0423 to LE45 - See Note 1* above



SATA 1.8"


- MTFDDAA480MBB, MTFDDAA800MBB to MC50 - See Note 1* above


Below drives are removed from the program - See Note 2* above

Product ID FW

IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST3300557SS EA54
IBM-ESXSST3450757SS EA54
IBM-ESXSST3600957SS EA54
IBM-ESXSST31000424SS BC2D
IBM-ESXSST32000444SS BC2D
IBM-ESXSST9300603SS B53E
IBM-ESXSST9146803SS B53E
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9500430SS BD14
IBM-ESXSST3300657SS BA5A
IBM-ESXSST3450857SS BA5A
IBM-ESXSST3600057SS BA5A
IBM-ESXSST9146703SS E537
IBM-ESXSST9300503SS E537
IBM-ESXSST973352SS E626
IBM-ESXSST9146752SS E626
IBM-ESXSST9600204SS B54A
IBM-ESXSST9300605SS B55E
IBM-ESXSST9600205SS B55E
IBM-ESXSST9900805SS B55E
IBM-ESXSST9300505SS E558
IBM-ESXSST9600105SS E558
IBM-ESXSST9900705SS E558
IBM-ESXSST33000650SS BC3E
IBM-ESXSHUC106030CSS60 D3A6
IBM-ESXSHUC106060CSS60 D3A6
IBM-ESXSHUS723020ALS64 J3K8
IBM-ESXSHUS723030ALS64 J3K8
IBM-ESXSMBD2147RC SB1B
IBM-ESXSMBD2300RC SB1B
IBM-ESXSMBE2073RC SC18
IBM-ESXSMBE2147RC SC18
IBM-ESXSMBF2300RC SB2F
IBM-ESXSMBF2600RC SB2F
IBM-ESXSMK1401GRRB SC2E
IBM-ESXSMK3001GRRB SC2E
IBM-ESXSMK1401GRRR SF23
IBM-ESXSMK3001GRRR SF23
SG9XCS1F50GMIBM SA03SB6F
SG9XCS1B200GEIBM SA03SB6F
SG9XCS2D200GEIBM SA03SE6H
SG9XCS2D50GEIBM SA03SE6H
SG9XCS1F200GEIBM SA03SB6F
TX21B10200GE8IBM PRO6SP3E
TE22D10100GE8IBM PRO6SR3F
TX21B10400GE8IBM PRO6SP3E
WD2000F9YZ-23N2 WE31
WD3000F9YZ-23N2 WE31
WD4000F9YZ-23N2 WE31
WD2003FYYS-23T8B0 01.00D04
WD3000BLHX-23V7BV0 YA32
ST9160511NS BE1A
ST9500530NS BE1A
ST3500514NS BB2C
ST31000524NS BB2C
ST32000544NS BB2C
ST33000650NS BB3A
ST1000NM0011 BB4A
ST2000NM0011 BB4A
ST500NM0011 BB4A
HUA722010CLA330 JP4OA3PH
HUA722020ALA330 JKAOA3GA
HUA722050CLA330 JP2OA3PH
HDS721025CLA382 JP1OA54C
HUA723030ALA640 MKAOA930
HUA723020ALA640 MK7OA930
MTFDDAA512MAR-1K1AB MA57
MTFDDAK128MAR-1J1AA MA57
MTFDDAK256MAR-1K1AA MA57
MTFDDAK064MAR-1J1AA MA57
MTFDDAK512MAR-1K1AA MA57
MTFDDAA064MAR-1K1AB MA57
MTFDDAA128MAR-1K1AB MA57
MTFDDAA256MAR-1K1AB MA57
STECM8PSB2 2864
STECM8PSB2 SM08





**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.21.00 Build ID: IBM12100
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.21.00
- Update Utility release for IBM x86 servers.


This package acknowledges support and may include updates for
drives with product ID strings of:

SAS 3.5"

- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to BC5K

- ST2000NM0043, ST4000NM0043 to EC5H

- ST2000NM0034, ST4000NM0034, ST6000NM0034 to BC6E

- ST2000NM0054, ST4000NM0054, ST6000NM0054 to EC6E

- HUS724020ALS64, HUS724030ALS64, HUS724040ALS64 to MPXSJ3LA

- HUS724020ALS61, HUS724040ALS61 to MPXSN3LA

- VPCA300900EST1, VPCA450900EST, VPCA600900EST1 to VCXSA810



SAS 2.5"

- HUC156030CSS20, HUC156060CSS20 to KFXSJ2G8

- HUC101212CSS60 to CPXSJ2MC

- HUC101212CSS61 to CPXSN2MC

- HUC109030CSS60, HUC109060CSS60, HUC109090CSS60 to CEXSJ2EL

- HUC109030CSS61, HUC109060CSS61, HUC109090CSS61 to CEXSN2EL

- HUSMM1620ASS20, HUSMM1640ASS20, HUSMM1680ASS20, HUSMM1616ASS20
to SPXSJ4CC

- HUSMM1620ASS20E, HUSMM1640ASS20E, HUSMM1680ASS20E,
HUSMM1616ASS20E to SPXSN4CC

SATA 3.5"

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD40

- ST2000NM0024, ST4000NM0024, ST6000NM0024, ST5000NM0024 to BB67

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to BB5G


SATA 2.5"

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB to MB47

- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3 to EXT0CA35

- STECM8PSB2 to 2864/SM08


SATA 1.8"

- MTFDDAA120MBB, MTFDDAA240MBB, MTFDDAA480MBB, MTFDDAA800MBB to MB47




**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.20.00 Build ID: IBM12000
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.20.00
- Update Utility release for IBM x86 servers.

Note: *- Update the firmware on SAS/SATA SSDs to fix PSIRT issue with Intel SSD's.

This package acknowledges support and may include updates for
drives with product ID strings of:

SATA 2.5"


- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB480G4I, SSDSC2BB800G4I
to D201NE40.

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA39.

- SSDSC2BB080G4I, SSDSC2BB160G4I, SSDSC2BB300G4I, SSDSC2BB600G4I,
SSDSC2BB800G4I to D201NE40.

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC34.




SATA 1.8"

- SSDSC1NB080G4I, SSDSC1NB240G4I, SSDSC1NB400G4I to D201NE40.

- SSDSC1NA200G3I, SSDSC1NA400G3I to 5DV1NA39.

- SSDSC1NB800G4I to D201NE40.


**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.19.06 Build ID: IBM11906
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.19.06
- Update Utility release for IBM x86 servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

- Remove TXA2D20200GA6I, TXA2D20400GA6I, TXA2D20800GA6I,
TXA2E21600GA6I from FW update utility for new code updating break Raid.








**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.18.03 Build ID: IBM11803

Critical Release
Reference RETAIN TIP: H214784 - MIGR-5098277
Reference RETAIN TIP: H214635 MIGR-5098037

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.18.03
- Update Utility release for IBM x86 servers.


Note: * - Fixed extremely low probable data compare error on I/O held
in standby when followed by power cycle; extremely low probable
data compare error due to nonvolatile cache(NVC) write data not
getting written to disc.
RETAIN TIP: H214784 - MIGR-5098277

Note: # - Fixed a block misalignment during a sequential read.

RETAIN TIP: H214635 MIGR-5098037


SAS 3.5"

- ST2000NM0034, ST4000NM0034, ST6000NM0034 to BC6B - similar
to Note * above.

- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to
BC5J - Enhance Dither Algorithm to prevent dwelling during
Idle environments.
- ST2000NM0043, ST4000NM0043 to EC5E - Enhance Dither Algorithm
to prevent dwelling during Idle environments.


SAS 2.5"

- TXA2E21600GA6I to GB7P - add support in profile.

- HUC156030CSS20, HUC156060CSS20 to J2G6 - add support in profile.


SATA 3.5"

- ST2000NM0024, ST4000NM0024, ST5000NM0024, ST6000NM0024 to
BB66 - similar to Note * above.

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to
BB5F - Enhance Dither Algorithm to prevent dwelling during
Idle environments.


SATA 2.5"


- MTFDDAA120MBB, MTFDDAA240MBB, MTFDDAA480MBB, MTFDDAA800MBB to
MB42 - add support in profile.

- SSDSC2BB080G4I, SSDSC2BB160G4I, SSDSC2BB300G4I, SSDSC2BB600G4I to
D201NB39 - add support in profile.



**************************************************************************

IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.17.01 Build ID: IBM11701

Critical Release
Reference RETAIN TIP: H214784 - MIGR-5098277
Reference RETAIN TIP: H214635 MIGR-5098037

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.17.01
- Update Utility release for IBM x86 servers.


Note: * - Fixed extremely low probable data compare error on I/O held
in standby when followed by power cycle; extremely low probable
data compare error due to nonvolatile cache(NVC) write data not
getting written to disc.
RETAIN TIP: H214784 - MIGR-5098277

Note: # - Fixed a block misalignment during a sequential read.
RETAIN TIP: H214635 MIGR-5098037


This package acknowledges support of qualified devices and
may include updates for drives with product ID strings of:


SAS 3.5"

- HUS724020ALS61, HUS724040ALS61 to N3L6 - internal updates.

- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to
BC5H - See Note * above.

- ST2000NM0054, ST4000NM0054, ST6000NM0054 to EC66 - see Note * above.

- ST2000NM0043, ST4000NM0043 to EC5D - See Note * above.

- Other drive codes are present for support identification.



SAS 2.5"

- WD3001BKHG-23D, WD6001BKHG-23D, WD9001BKHG-23D
to ZA34 - follow-on release.
- WD3002BKTG-23E, WD6002BKTG-23E, WD9002BKTG-23E
to ZC33 - follow-on release.

- HUC109030CSS60, HUC109060CSS60, HUC109090CSS60
to J2EH - follow-on release.

- TXA2D20200GA6I, STXA2D20400GA6I, TXA2D20800GA6I,
TXA2E21600GA6I to GB7P - enhancements.

- ST300MM0006, ST600MM0006, ST900MM0006 to B56T -
See Note * above.

- ST300MM0026, ST600MM0026, ST900MM0026 to E56E -
See Note * above.

- ST2000NM0043, ST4000NM0043 to EC5D - See Note * above.

- ST1200MM0007 to B57E - See Note * above.

- ST1200MM0017 to E577 - See Note * above.

- HUSMM1620ASS20, HUSMM1640ASS20, HUSMM1680ASS20, HUSMM1616ASS20 to
J4C8 - See Note # above
- HUSMM1620ASS20E, HUSMM1640ASS20E, HUSMM1680ASS20E, HUSMM1616ASS20E
to N4C8 - See Note # above

- Other drive codes are present for support identification.


SATA 3.5"

- MG04ACA200E, MG04ACA300E, MG04ACA400E, MG04ACA500E to SJ1D
- performance inhancements.

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to
BB5C - See Note * above.

- ST2000NM0024, ST4000NM0024, ST5000NM0024, ST6000NM0024 to
BB65 - See Note * above.

- WD2003FYYS-23W0B0 to WA36 - configuration additions.

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD39 -
configuration additions.

- HUA723030ALA6 to MKAOA930 - enhancements.
- HUA723020ALA6 to MK7OA930 - enhancements.

- Other drive codes are present for support identification.


SATA 2.5"


- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3 to
EXT0CA34 - ship level.

- Other drive codes are present for support identification.


SATA 1.8"

- Drive codes are present for support identification.



**************************************************************************

IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.16.05 Build ID: IBM11605

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.05
- Update Utility release for IBM x86 servers.

This package acknowledges support and may include updates for
drives with product ID strings of:


SAS 3.5"

- ESXSST1000NM0001, ESXSST2000NM0001 to BC4B - ensures that after
servicing an 03/11/00 error, an index for Parity Creations is calculated
correctly after a power cycle, that would otherwise make the
drive unresponsive.

- ESXSHUS724020ALS64, ESXSHUS724030ALS64, ESXSHUS724040ALS64
to J3L6 - Fixed unexpected 02/04/11 error; Fixed a drive logic self-initiated
reset on read/write long commands; Fixed a problem with large write sequential
transfers.

SAS 2.5"

- ESXSST9500620SS, ESXSST91000640SS to BD2K - ensures that after
servicing an 03/11/00 error, an index for Parity Creations is calculated
correctly after a power cycle, that would otherwise make the
drive unresponsive.

SATA 2.5"

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC32 - SCT WriteSame fix.



IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.16.04 Build ID: IBM11604

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.04
- Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

NOTE: Check notation under PCIe NVMe devices.

SATA 2.5"

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB to
MB42 -
> A drop in host power supply may cause bad block growth
> The bad block table may not properly increment
> Background activity may continue after STANDBY, STANDBY IMMEDIATE,
or SLEEP
> ID173/202 may show incorrect value when the NAND erase count exceeds 3000
> Changed DRAM timing
> Event log may be programmed when supply voltage from host is out of
specification

- SSDSC2BB012I4I, SSDSC2BB016T4I to G201NC32 - SCT WriteSame fix
that corrects a condition that may cause the drive to not respond.


PCIe NVMe 2.5"

- SSDPE2ME400G4I, SSDPE2ME800G4I, SSDPE2ME016G4I, SSDPE2ME020G4I
to 8DV1ND34 - will require two update runs and system reboots for device
fw update to complete--Please See the limitations in readme for details.

> Performance improvement on sub-4KB sequential write
> Fix drive reports higher than actual data units read and write
> Fix drive incorrectly counts unsafe power shutdown events on warm reboots


IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.16.03 Build ID: SAS11603

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.03
- Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

NOTE: Check notation under PCIe NVMe devices.

SAS 3.5"

- ESXSST2000NM0034, ESXSST4000NM0034, ESXSST6000NM0034 to BC67
- GA code.
- ESXSST2000NM0054, ESXSST4000NM0054, ESXSST6000NM0054 to EC66
- GA code.

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to XA39 - issues fixed:
slow performance with PI enabled;
drive hang on uncorrectable rd error in reallocation track;
PERSISTANT RESERVATION command not working correctly;
reliability improvements around off-track write protection.


SAS 2.5"

- ESXSTXA2D20200GA6, ESXSTXA2D20400GA6, ESXSTXA2D20800GA6,
ESXSTXA2E21600GA6 to GB7P - fixes implemented to support PI
issues.

- ESXSST300MP0005 to B675 - GA code.
- ESXSST300MP0025 to E671 - GA code.

- ESXSST300MP0035, ESXSST600MP0035 to B683 - GA code.
- ESXSST300MP0045, ESXSST300MP0045 to E685 - GA code.

- ESXSST300MX0012, ESXSST600MX0052 to BH53 - GA code.

- ESXSWD3001BKHG-23D, ESXSWD6001BKHG-23D, ESXSWD9001BKHG-23DS
to ZA34 - issues fixed:
slow performance with PI enabled;
drive hang on uncorrectable rd error in reallocation track;
PERSISTANT RESERVATION command not working correctly;
drive was reporting 0B/11 instead of 03/11.
- ESXSWD3002BKTG-23E, ESXSWD6002BKTG-23E, ESXSWD9002BKTG-23E
to ZC33 - issues fixed:
slow performance with PI enabled;
drive hang on uncorrectable rd error in reallocation track;
PERSISTANT RESERVATION command not working correctly;
reliability improvements around off-track write protection.


SATA 3.5"

- MG04ACA200E, MG04ACA300E, MG04ACA400E, MG04ACA500E to SJ1C - GA code


SATA 2.5"


- ST9250610NS, ST9500620NS, ST91000640NS to BE2B - Update configuration change.

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB to
MB34 -
> Some Out of Range LBAs accepted by NCQ commands where
they should be aborted.
> SataDownShift.srt failed, Smart attribute Raw lost with
perform dirty pwr cycle .
> Low Power Entry Bug Identified from Marvell Code Review
> Track Timeout, Marvel 373 sequencer issue
> Unreasonable ECC count in SMART ID 195


- SSDSC2BB080G4I, SSDSC2BB160G4I, SSDSC2BB300G4I, SSDSC2BB600G4I to
D201NB39 - SCT WriteSame Disable.

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA38 -
CDC Fix for 15GB default values (should abort); SCT WriteSame
Disable.

- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB480G4I, SSDSC2BB800G4I to
D201NB39/D201NE39 - SCT WriteSame Disable.


**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program for Linux.
Version 1.16.00 Build ID: SAS11600

*******************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.00
- First Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

NOTE: Check notation under PCIe NVMe devices.

SAS 3.5"

- ESXSST1000NM0023, ESXSST2000NM0023, ESXSST3000NM0023,
ESXSST4000NM0023 to BC5E

- ESXSST2000NM0043, ESXSST3000NM0043, ESXSST4000NM0043,
ESXSST1000NM0043 to EC5A

- ESXSST3300557SS, ESXSST3450757SS, ESXSST3600957SS to EA54

- ESXSST3300657SS, ESXSST3450857SS, ESXSST3600057SS to BA5A

- ESXSST33000650SS to BC3E

- ESXSST1000NM0001, ESXSST2000NM0001 to BC4A

- ESXSHUS724020ALS64, ESXSHUS724030ALS64, ESXSHUS724040ALS64
to J3L5

- ESXSHUS724020ALS61, ESXSHUS724040ALS61 to N3L5

- ESXSHUS723020ALS64, ESXSHUS723030ALS64 to J3K8

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to XA38



SAS 2.5"

- ESXSTXA2D20200GA6I, ESXSTXA2D20400GA6I, ESXSTXA2D20800GA6I,
ESXSTXA2E21600GA6I to GB7H

- ESXSST300MM0006, ESXSST600MM0006, ESXSST900MM0006 to B56M;
- ESXSST300MM0026, ESXSST600MM0026, ESXSST900MM0026 to E56D

- ESXST1200MM0007 to B57B
- ESXST1200MM0017 to E576

- ESXSST9300605SS, ESXSST9600205SS, ESXSST9900805SS to B55E
- ESXSST9300505SS, ESXSST9600105SS, ESXSST9900705SS to E558

- ESXSST9146853SS, ESXSST9300653SS to B63K

- ESXSST9146753SS, ESXSST9300553SS to E638
- ESXSST9500620SS, ESXSST91000640SS to BD2J

- ESXSHUC101212CSS60 to J2MA
- ESXSHUC101212CSS61 to N2M9

- ESXSHUC156030CS420, ESXSHUC156060CS420 to J5G2
- ESXSHUC156030CSS20, ESXSHUC156060CSS20 to J2G4

- ESXSHUC156030CS420E, ESXSHUC156060CS420E to N5G2

- ESXSHUC156030CSS20E, ESXSHUC156060CSS20E to N2G4

- ESXSHUC101860CS420, ESXSHUC101890CS420, ESXSHUC101812CS420,
ESXSHUC101818CS420 to J5H2
- ESXSHUC101860CS420E, ESXSHUC101890CS420E, ESXSHUC101812CS420E,
ESXSHUC101818CS420E to N5H2

- ESXSHUC109030CSS60, ESXSHUC109060CSS60, ESXSHUC109090CSS60
to J2EG
- ESXSHUC109030CSS61E, ESXSHUC109060CSS61E, ESXSHUC109090CSS61E
to N2EG

- ESXSAL13SXB300N, ESXSAL13SXB600N to SC36

- ESXSMBF2300RC, ESXSMBF2600RC to SB2F

- ESXSMK1401GRRB, ESXSMK3001GRRB to SC2E
- ESXSMK1401GRRR, ESXSMK3001GRRR to SF23
- ESXSMK3001GRDB, ESXSMK6001GRDB, ESXSMK9001GRDB to SB35

- ESXSWD3001BKHG-23D, ESXSWD6001BKHG-23D, ESXSWD9001BKHG-23D
to ZA33
- ESXSWD3002BKTG-23E, ESXSWD6002BKTG-23E, ESXSWD9002BKTG-23E
to ZC32

- EXSXHUSMM1620ASS20, EXSXHUSMM1640ASS20, EXSXHUSMM1680ASS20,
EXSXHUSMM1616ASS20 to J4C6
- EXSXHUSMM1620ASS20E, EXSXHUSMM1640ASS20E, EXSXHUSMM1680ASS20E,
EXSXHUSMM1616ASS20E to N4C6



SATA 3.5"

- WD1003FBYX-23Y7B0, WD2003FYYS-23W0B0 to WA35

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD37 -
Resolves drive initiated reset (DBS (Debug Stop event))
encountered under a narrow timing window (~1ns) for specific
command/access patterns, due to the drive’s handling of
command automation where it was possible for an internal
hardware resource conflict to occur between two tasks.

- ST33000650NS to BB3A

- ST1000NM0011, ST2000NM0011 to BB4A

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033
to BB5A

- HUA723020ALA640 to MK7OA930
- HUA723030ALA640 to MKAOA930



SATA 2.5"

- ST9250610NS, ST9500620NS, ST91000640NSto BE2A

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB
to MB33

- SSDSC2BB080G4I, SSDSC2BB120G4I, SSDSC2BB160G4I, SSDSC2BB240G4I,
SSDSC2BB300G4I, SSDSC2BB480G4I, SSDSC2BB600G4I, SSDSC2BB800G4I
to D201NB38

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC31

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA37

- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3
to EXST0CA34


PCIe NVMe 2.5"

- SSDPE2ME400G4I, SSDPE2ME800G4I, SSDPE2ME016G4I, SSDPE2ME020G4I
to 8DV1ND32 - will require a system reboot for device fw
update to complete.


*********************************************************************
SAS/SATA HDD/SSD Update Program
Version 1.15.00
- First Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:



SAS 3.5"

- ESXSST1000NM0023, ESXSST2000NM0023, ESXSST3000NM0023,
ESXSST4000NM0023 to BC5E

- ESXSST2000NM0043, ESXSST3000NM0043, ESXSST4000NM0043,
ESXSST1000NM0043 to EC5A

- ESXSST3300557SS, ESXSST3450757SS, ESXSST3600957SS to EA54

- ESXSST3300657SS, ESXSST3450857SS, ESXSST3600057SS to BA5A

- ESXSST33000650SS to BC3E

- ESXSST1000NM0001, ESXSST2000NM0001 to BC4A

- ESXSHUS724020ALS64, ESXSHUS724030ALS64, ESXSHUS724040ALS64
to J3L5

- ESXSHUS724020ALS61, ESXSHUS724040ALS61 to N3L5

- ESXSHUS723020ALS64, ESXSHUS723030ALS64 to J3K8

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to XA38



SAS 2.5"

- ESXSTXA2D20200GA6I, ESXSTXA2D20400GA6I, ESXSTXA2D20800GA6I,
ESXSTXA2E21600GA6I to GB7H

- ESXSST300MM0006, ESXSST600MM0006, ESXSST900MM0006 to B56M;
- ESXSST300MM0026, ESXSST600MM0026, ESXSST900MM0026 to E56D

- ESXST1200MM0007 to B57B
- ESXST1200MM0017 to E576

- ESXSST9300605SS, ESXSST9600205SS, ESXSST9900805SS to B55E
- ESXSST9300505SS, ESXSST9600105SS, ESXSST9900705SS to E558

- ESXSST9146853SS, ESXSST9300653SS to B63K

- ESXSST9146753SS, ESXSST9300553SS to E638
- ESXSST9500620SS, ESXSST91000640SS to BD2J

- ESXSHUC101212CSS60 to J2MA
- ESXSHUC101212CSS61 to N2M9

- ESXSHUC156030CS420, ESXSHUC156060CS420 to J5G2
- ESXSHUC156030CSS20, ESXSHUC156060CSS20 to J2G4

- ESXSHUC156030CS420E, ESXSHUC156060CS420E to N5G2

- ESXSHUC156030CSS20E, ESXSHUC156060CSS20E to N2G4

- ESXSHUC101860CS420, ESXSHUC101890CS420, ESXSHUC101812CS420,
ESXSHUC101818CS420 to J5H2
- ESXSHUC101860CS420E, ESXSHUC101890CS420E, ESXSHUC101812CS420E,
ESXSHUC101818CS420E to N5H2

- ESXSHUC109030CSS60, ESXSHUC109060CSS60, ESXSHUC109090CSS60
to J2EG
- ESXSHUC109030CSS61E, ESXSHUC109060CSS61E, ESXSHUC109090CSS61E
to N2EG

- ESXSAL13SXB300N, ESXSAL13SXB600N to SC36

- ESXSMBF2300RC, ESXSMBF2600RC to SB2F

- ESXSMK1401GRRB, ESXSMK3001GRRB to SC2E
- ESXSMK1401GRRR, ESXSMK3001GRRR to SF23
- ESXSMK3001GRDB, ESXSMK6001GRDB, ESXSMK9001GRDB to SB35

- ESXSWD3001BKHG-23D, ESXSWD6001BKHG-23D, ESXSWD9001BKHG-23D
to ZA33
- ESXSWD3002BKTG-23E, ESXSWD6002BKTG-23E, ESXSWD9002BKTG-23E
to ZC32

- EXSXHUSMM1620ASS20, EXSXHUSMM1640ASS20, EXSXHUSMM1680ASS20,
EXSXHUSMM1616ASS20 to J4C6
- EXSXHUSMM1620ASS20E, EXSXHUSMM1640ASS20E, EXSXHUSMM1680ASS20E,
EXSXHUSMM1616ASS20E to N4C6



SATA 3.5"

- WD1003FBYX-23Y7B0, WD2003FYYS-23W0B0 to WA35

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD37

- ST9500620NS, ST91000640NS to BE2A

- ST33000650NS to BB3A

- ST1000NM0011, ST2000NM0011 to BB4A

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033
to BB5A

- HUA723020ALA640 to MK7OA930
- HUA723030ALA640 to MKAOA930



SATA 2.5"

- ST9500620NS, ST91000640NS

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB
to MB33

- SSDSC2BB080G4I, SSDSC2BB120G4I, SSDSC2BB160G4I, SSDSC2BB240G4I,
SSDSC2BB300G4I, SSDSC2BB480G4I, SSDSC2BB600G4I, SSDSC2BB800G4I
to D201NB37

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC31

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA36

- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3
to EXST0CA34

NOTE TO SERVICE - Reference RETAIN TIP H29851
*******************************************
SAS Hard Disk Drive Update Program
Version 1.14.04
Critical Release
Reference RETAIN TIP H29851

This package includes updates to drives with product ID strings of:

SAS 2.5"

Initial code Release
- SMK3001GRDB, SMK6001GRDB, SMK9001GRDB to SB35


SATA 2.5"

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to NA36
- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB400G4I, SSDSC2BB800G4I
to NB37 - fix to prevent possible drive lock up during format.


SATA 1.8"

Initial Code Release
- SSDSC1NA200G3I, SSDSC1NA400G3I to NA36
- SSDSC1NB080G4I, SSDSC1NB240G4I, SSDSC1NB400G4I to NB37
- fix to prevent possible drive lock up during format.

===================================================================
IBM Online SAS/SATA Hard Disk Drive Update Program
Version 1.14.03-2 Build ID: SAS11403-2

NOTE TO SERVICE - Reference RETAIN TIPS H211424 & H211667
*******************************************
IBM SAS Hard Disk Drive Update Program
Version 1.14.03-2
Critical Release
Reference RETAIN TIP H211424 & H211667

This package includes updates to drives with product ID strings of:


SAS 3.5"

Initial Code Releases
- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to BC5B
- ST2000NM0043, ST4000NM0043 to EC59
- WD1001FYYG-23S, WD2001FYYG-23S, WD3001FYYG-23S,
WD4001FYYG-23S to XA35

Other
- ST1000NM0001, ST2000NM0001 to BC4A - support persistent reservation
- HUS723020ALS64, HUS723030ALS64 to J3K8 - servo adjustments


SAS 2.5"

Initial Code Releases
- ST300MM0006, ST600MM0006, ST900MM0006 to B56H
- ST300MM0026, ST600MM0026, ST900MM0026 to E568
- TXA2D20200GA6I, TXA2D20400GA6I, TXA2D20800GA6I, TXA2D21600GA6I
to GB76 - see Retain Tip H211424.
- HUC101212CSS60 to J2M7
- HUC101212CSS61 to N2M7
- T1200MM0007 to B576
- T1200MM0017 to E574
- ST600MX0001 to BH13
- WD3002BKTG-23E, WD6002BKTG-23E, WD9002BKTG-23E to ZC31
- ST9500431SS to ED12
- ST9146703SS to E536
- ST973352SS to E625
- ST9300553SS to E636
- HUC109030CSS61E, HUC109060CSS61E, HUC109090CSS61E to N2EF
- MK3001GRDB, MK6001GRDB, MK9001GRDB to SB35 - drive Que depth fix;
see Retain Tip H211667.
- HUC109030CSS60, HUC109060CSS60, HUC109090CSS60 to J2EF
- HUC109030CSS61E, HUC109060CSS61E, HUC109090CSS61E to N2EF

Other
- WD3001BKHG-23D, WD6001BKHG-23D, WD9001BKHG-23D to ZA32 -
performance, non-critical fixes and robustness changes.

- ST9600204SS to B54A with maintainance fixes and performance
improvements.

- MBD2147RC, MBD2300RC to SB1B - drive Que depth fix;
- MBE2073RC, MBE2147RC to SC18 - drive Que depth fix;
- MBF2300RC, MBF2600RC to SB2F - drive Que depth fix;
- MK1401GRRB, MK3001GRRB to SC2E - drive Que depth fix;
see Retain Tip H211667.

- ST9500620SS, ST91000620SS to BD2F - support persistent reservation
and maintainance fixes.


SATA 3.5"

Initial Code Release
- WD801ABYS-23C0A0, WD1601ABYS-23C0A0 to 06.06H05
- WD5003ABYX-23 to WC38 - added mfg. parameters.
- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD36
- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to BB58

Other


SATA 2.5"

Initial Code Release
- SG9XCS2D50GEIBM to SE6H
- WD3000BLHX-23V7BV to YA31
- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to NA34
- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB400G4I, SSDSC2BB800G4I
to NB34

Other
- ST9250610NS, ST9500620NS, ST91000640NS to BE29 - maintainance
updates.
- MTFDDAK064MAR-1J1AA, MTFDDAK128MAR-1J1AA, MTFDDAK256MAR-1K1AA,
MTFDDAK512MAR-1K1AA to MA57 - added mfg. parameters.


SATA 1.8"

Initial Code Release
- SSDSC1NA200G3I, SSDSC1NA400G3I to NA34
- SSDSC1NB080G4I, SSDSC1NB240G4I, SSDSC1NB400G4I to NB34

Other
- MTFDDAA064MAR-1J1AB, MTFDDAA128MAR-1J1AB, MTFDDAA256MAR-1K1AB,
MTFDDAA512MAR-1K1AB to MA57 - added mfg. parameters.

===================================================================
Version 1.13.01 Build ID: SAS_113

NOTE TO SERVICE - Reference RETAIN H207993

*******************************************
IBM SAS Hard Disk Drive Update Program
Version 1.13.01
Critical Release
Reference RETAIN H207993

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- HUS723020ALS64 to J3K7 Additions to VPD information used by
manufacturing and fixes for overall robustness.

- HUS723030ALS64 to J3K7 Initial Code Release

- ST31000424SS, ST32000444SS to BC2D
- ST1000NM0001, ST2000NM0001 to BC49
Fixes for overall robustness.

- ST33000650SS to BC3E Initial Code Release


SAS 2.5"

- MK1401GRRB, MK3001GRRB to SC29
Fixes for overall robustness.

- MBF2300RC, MBF2600RC to SB2C
Initial Code Release.

- ST9300605SS, ST9600205SS, ST9900805SS to B55D
ST9146853SS, ST9300653SS to B63B
ST9500620SS, ST91000640SS to BD2E
ST9300505SS, ST9600105SS, ST9900705SS to E557
ST9146753SS to E636
Additions to VPD information used by manufacturing and
fixes for overall robustness.

SATA 3.5"

- ST500NM0011, ST2000NM0011, ST1000NM0011 to BB4A
ST3500514NS, ST31000524NS, ST32000644NS to BB2C
Reliability improvements, Additions to VPD information
used by manufacturing

- ST33000650NS to BB3A Initial Code Release

- WD5003ABYX-23 to WC36, WD1003FBYX-23Y7B0 to WB35,
WD2003FYYS-23W0B0 to WA35
Reliability improvements, Additions to VPD information
used by manufacturing

- HUA723020ALA640 to MK7OA910
Additions to VPD information used by manufacturing.

- HUA723030ALA640 to MKAOA910 Initial Code Release

- HUA722050CLA330, HUA722010CLA330 to A3PH
Initial Code Release

SATA 2.5"

- TE22D10100GE8IBM to SR3B Initial Code Release

- MTFDDAK064MAR-1J1AA, MTFDDAK128MAR-1J1AA,
MTFDDAK256MAR-1K1AA, MTFDDAK512MAR-1K1AA
to MA55 Initial Code Release

- ST9250610NS, ST9500620NS, ST91000640NS to BE28
Fixes for overall robustness.

SATA 1.8"

- MTFDDAA064MAR-1J1AB, MTFDDAA128MAR-1J1AB,
MTFDDAA256MAR-1K1AB, MTFDDAA512MAR-1K1AB
to MA55 Initial Code Release

- TX21B10100GE8IBM, TX21B10200GE8IBM, TX21B10400GE8IBM
to SP3A Initial Code Release

===============================================================

Version 1.12.01
Critical Release
Reference RETAIN #H207740

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- VPCA300900EST1, VPCA450900EST1, VPCA600900EST1 to A3C4,
Corrects firmware bug that may cause data corruption.
For further information, please refer to Retain Tip H207740.

===============================================================

Version 1.12
(Critical)

Added Support for SAS Controllers M5115 and H1135

SAS 3.5"
Product ID FW

IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4D
IBM-ESXSST3300656SS BA4D
IBM-ESXSST3450856SS BA4D
IBM-ESXSST3300657SS BA5A
IBM-ESXSST3450857SS BA5A
IBM-ESXSST3600057SS BA5A
IBM-ESXSST3750630SS BC1I
IBM-ESXSST31000640SS BC1I
IBM-ESXSST31000424SS BC2C
IBM-ESXSST32000444SS BC2C
IBM-ESXSST33000650SS BC3D
IBM-ESXSST1000NM0001 BC48
IBM-ESXSST2000NM0001 BC48
IBM-ESXSVPCA300900EST1 A3C2
IBM-ESXSVPCA600900EST1 A3C2
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSHUS723020ALS64 J26C
IBM-ESXSHUS723030ALS64 J26C
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5"
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST973402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53E
IBM-ESXSST9146803SS B53E
IBM-ESXSST9600204SS B549
IBM-ESXSST9300605SS B55C
IBM-ESXSST9600205SS B55C
IBM-ESXSST9900805SS B55C
IBM-ESXSST936751SS B617
IBM-ESXSST973451SS B617
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9146853SS B63A
IBM-ESXSST9300653SS B63A
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD2C
IBM-ESXSST91000640SS BD2C
IBM-ESXSST9300503SS E536
IBM-ESXSST9300505SS E555
IBM-ESXSST9600105SS E555
IBM-ESXSST9900705SS E555
IBM-ESXSST9146752SS E625
IBM-ESXSST9146753SS E635
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D3A6
IBM-ESXSHUC106060CSS60 D3A6
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBF2300RC SB2B
IBM-ESXSMBF2600RC SB2B
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMK1401GRRB SC27
IBM-ESXSMK3001GRRB SC27
IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107
IBM-ESXSWD9001BKHG-23D ZA31
IBM-ESXSWD6001BKHG-23D ZA31
IBM-ESXSWD3001BKHG-23D ZA31

SATA 3.5"
Product ID FW

WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WD1602ABYS-23B7A0 02.03B07
WD2502ABYS-23B7A0 02.03B08
WD2003FYYS-23W0B0 WA34
WDC WD1003FBYX-23Y7B0 WB33
WD5003ABYX-23 WC34
ST380819AS 3.05
ST3160828AS 3.05
ST340212AS 3.05
ST3160023AS 3.48
ST380013AS 3.48
ST340014AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB15
ST3500320NS BB15
ST3750330NS BB15
ST31000340NS BB15
ST3500514NS BB2A
ST31000524NS BB2A
ST32000644NS BB2A
ST33000650NS BB38
ST1000NM0011 BB47
ST2000NM0011 BB47
ST500NM0011 BB47
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3IA
HDS721025CLA382 JP1OA54C
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
HUA723020ALA640 MK7OA900
HUA723030ALA640 MKAOA900
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE1A
ST9500530NS BE1A
ST9250610NS BE25
ST9500620NS BE25
ST91000640NS BE25

SSD
Product ID FW

TX21B10200GE1IBM PRO6SP36
TX21B10400GE1IBM PRO6SP36
TX21B10100GE8IBM PRO6SP36
TE22D10100GE8IBM PRO6SR36
SG9XCS1B50GMIBM SA03SB6F
SG9XCS1F200GEIBM SA03SB6F
SG9XCS2D200GEIBM SA03SE6H
GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
MTFDDAA512MAR-1K1AB MA52
MTFDDAK128MAR-1J1AA MA52
MTFDDAK256MAR-1K1AA MA52
MTFDDAK064MAR-1J1AA MA52
MTFDDAK512MAR-1K1AA MA52
MTFDDAA064MAR-1K1AB MA52
MTFDDAA128MAR-1K1AB MA52
MTFDDAA256MAR-1K1AB MA52
STEC M8PSB1 0409
STEC MACH8 IOPS 2804
STEC M8PSB2 T4 SM06
STEC M8PSB1 T4 SM16

SAS 3.5"

- ST3300657SS, ST3450857SS, ST3600057SS to BA5A
VPCA300900EST1, VPCA600900EST1 to A3C2
Additions to VPD information used by manufacturing

- ST3750630SS, ST31000640SS to BC1I
ST31000424SS, ST32000444SS to BC2C
Mode Page change to address performance issues under certain system configurations

- ST33000650SS to BC3D
ST1000NM0001, ST2000NM0001 to BC48
Protection Information Fix - see Retain Tip H206140

- HUS723020ALS64, HUS723030ALS64 to J26C
Initial Code Release

SAS 2.5"

- ST9300603SS, ST9146803SS to B53E
ST9600204SS to B549
Additions to VPD information used by manufacturing

- ST9300605SS, ST9600205SS, ST9900805SS to B55C
ST9146853SS, ST9300653SS to B63A
ST9500620SS, ST91000640SS to BD2C
ST9300505SS to E555
ST9146753SS to E635
Protection Information Fix - see Retain Tip H206140

- ST9600105SS, ST9900705SS to E555
Inital Code Release

- HUC106030CSS60, HUC106060CSS60 to D3A6
Performance improvements, critical fixes for Protection Information (PI)
operation - see Retain Tip H206140

- MK1401GRRB, MK3001GRRB to SC27
Additions to VPD information used by manufacturing

- WD9001BKHG-23D, WD6001BKHG-23D, WD3001BKHG-23D to ZA31
Initial Code Release

SATA 3.5"

- WD2502ABYS-23B7A0 to 02.03B08
WD1602ABYS-23B7A0 to 02.03B07
Critical fix to address premature drive failures.

- ST3500514NS, ST31000524NS, ST32000644NS to BB2A
ST33000650NS to BB38
ST1000NM0011, ST2000NM0011, ST500NM0011 to BB47
Fixes a potential, but rare data corruption issue which requires
a background reallocation that exceeds the error recovery timer.

- HUA723020ALA640 to MK70A900
HUA723030ALA640 to MKA0A900
Initial Code Release

SATA 2.5"

- ST9160511NS, ST9500530NS to BE1A
- ST9250610NS, ST9500620NS, ST91000640NS to BE25
Fixes a potential, but rare data corruption issue which requires
a background reallocation that exceeds the error recovery timer.

SSD

- TX21B10200GE1IBM, TX21B10400GE1IBM, TX21B10100GE8IBM to PRO6SP36
TE22D10100GE8IBM to PRO6SR36
Initial Code Release

- MTFDDAK128MAR-1J1AA, MTFDDAK256MAR-1K1AA to MA52
Initial Code Release

- MTFDDAA512MAR-1K1AB, MTFDDAK064MAR-1J1AA, MTFDDAK512MAR-1K1AA,
MTFDDAA064MAR-1K1AB, MTFDDAA128MAR-1K1AB, MTFDDAA256MAR-1K1AB to MA52
Fixes SMART attribute 190 (Current Temp) which caused warning messages
with some versions of Linux

- STEC MACH8 IOPS to 2804
STEC M8PSB2 T4 to SM06
Additions to VPD information used by manufacturing
Fixes potential drive failure if power loss occurs during firmware update.

*******************************************

Version 1.11
(Critical)

SAS 3.5"
Product ID FW

IBM-ESXSVPCA300900EST1 A3C0
IBM-ESXSVPCA600900EST1 A3C0
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4D
IBM-ESXSST3300656SS BA4D
IBM-ESXSST3450856SS BA4D
IBM-ESXSST3300657SS BA59
IBM-ESXSST3450857SS BA59
IBM-ESXSST3600057SS BA59
IBM-ESXSST3750630SS BC1H
IBM-ESXSST31000640SS BC1H
IBM-ESXSST31000424SS BC2B
IBM-ESXSST32000444SS BC2B
IBM-ESXSST33000650SS BC3A
IBM-ESXSST1000NM0001 BC44
IBM-ESXSST2000NM0001 BC44
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5"
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSSTLFF_SATA3401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSSTLFF_SATA3401SS B51D
IBM-ESXSSTLFF_SATA3402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53C
IBM-ESXSST9146803SS B53C
IBM-ESXSST9600204SS B548
IBM-ESXSST9300605SS B559
IBM-ESXSST9600205SS B559
IBM-ESXSST9900805SS B559
IBM-ESXSST936751SS B617
IBM-ESXSSTLFF_SATA3451SS B617
IBM-ESXSSTLFF_SATA3452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9146853SS B637
IBM-ESXSST9300653SS B637
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD29
IBM-ESXSST91000640SS BD29
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D390
IBM-ESXSHUC106060CSS60 D390
IBM-ESXSST9300503SS E536
IBM-ESXSST9300505SS E553
IBM-ESXSST9146752SS E625
IBM-ESXSST9146753SS E633
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBF2300RC SB28
IBM-ESXSMBF2600RC SB28
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMK1401GRRB SC23
IBM-ESXSMK3001GRRB SC23
IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107

SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB15
ST3500320NS BB15
ST3750330NS BB15
ST31000340NS BB15
ST3500514NS BB29
ST31000524NS BB29
ST32000644NS BB29
ST33000650NS BB36
ST1000NM0011 BB46
ST2000NM0011 BB46
ST500NM0011 BB46
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HDS721025CLA382 JP1OA3GE
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31
WD5003ABYX-23 WC31
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WDC WD2502ABYS-23B7A0 02.03B06
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE19
ST9500530NS BE19
ST9250610NS BE24
ST9500620NS BE24
ST91000640NS BE24

SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2765
STEC M8PSB2 T4 SM05
SG9XCS2D200GEIBM SA03SE6C
MTFDDAK128MAR-1JAAB MA44
MTFDDAK256MAR-1JAAB MA44

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0409
STEC M8PSB1 T4 SM16
SG9XCS1B50GMIBM SA03SB6C
SG9XCS1F200GEIBM SA03SB6C


SAS 3.5"

- ST33000650SS to BC3A
ST1000NM0001, ST2000NM0001 to BC44
Additions and corrections to VPD information used by manufacturing

SAS 2.5"

- ST9300605SS, ST9600205SS, ST9900805SS to B559
ST9146853SS, ST9300653SS to B637
ST9500620SS, ST91000640SS to BD29
ST9300505SS to E553
SST9146753SS to E633
HUC106030CSS60, HUC106060CSS60 to D390
Additions and corrections to VPD information used by manufacturing

- MK1401GRRB, MK3001GRRB to SC23
Fixes a pottential data corruption bug if there is an
unexpected power loss.

SATA 3.5"

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB15
ST3500514NS, ST31000524NS, ST32000644NS to BB29
ST33000650NS to BB36
ST1000NM0011, ST2000NM0011, ST500NM0011 to BB46

SATA SSD

- SG9XCS1B50GMIBM, SG9XCS1F200GEIBM to SA03SB6C
SG9XCS2D200GEIBM to SA03SE6C
Fix for potential hang during an unexpected power cycle

MTFDDAK128MAR-1JAAB, MTFDDAK256MAR-1JAAB to MA44
Initial Release

===========================================

Version 1.10
(Critical)

SAS 3.5"
Product ID FW

IBM-ESXSVPCA300900EST1 A3C0
IBM-ESXSVPCA600900EST1 A3C0
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4C
IBM-ESXSST3300656SS BA4C
IBM-ESXSST3450856SS BA4C
IBM-ESXSST3300657SS BA58
IBM-ESXSST3450857SS BA58
IBM-ESXSST3600057SS BA58
IBM-ESXSST3750630SS BC1H
IBM-ESXSST31000640SS BC1H
IBM-ESXSST31000424SS BC2B
IBM-ESXSST32000444SS BC2B
IBM-ESXSST33000650SS BC37
IBM-ESXSST1000NM0001 BC42
IBM-ESXSST2000NM0001 BC42
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5" (SFF)
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST973402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53C
IBM-ESXSST9146803SS B53C
IBM-ESXSST9600204SS B548
IBM-ESXSST9300605SS B556
IBM-ESXSST9600205SS B556
IBM-ESXSST9900805SS B556
IBM-ESXSST936751SS B617
IBM-ESXSST973451SS B617
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9146853SS B635
IBM-ESXSST9300653SS B635
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD26
IBM-ESXSST91000640SS BD26
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D340
IBM-ESXSHUC106060CSS60 D340
IBM-ESXSST9300503SS E536
IBM-ESXSST9300505SS E552
IBM-ESXSST9146752SS E625
IBM-ESXSST9146753SS E632
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBF2300RC SB28
IBM-ESXSMBF2600RC SB28
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107

SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB15
ST3500320NS BB15
ST3750330NS BB15
ST31000340NS BB15
ST3500514NS BB29
ST31000524NS BB29
ST32000644NS BB29
ST33000650NS BB34
ST1000NM0011 BB45
ST2000NM0011 BB45
ST500NM0011 BB45
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HDS721025CLA382 JP1OA3GE
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31
WD5003ABYX-23 WC31
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WDC WD2502ABYS-23B7A0 02.03B06
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE19
ST9500530NS BE19
ST9250610NS BE24
ST9500620NS BE24
ST91000640NS BE24

SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2765
STEC M8PSB2 T4 SM05
SG9XCS2D200GEIBM SA03SE6C

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0409
STEC M8PSB1 T4 SM16
SG9XCS1B50GMIBM SA03SB6C
SG9XCS1F200GEIBM SA03SB6C

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- VPCA300900EST1, VPCA600900EST1 to A3C0
Correction to VPD information used by manufacturing

- ST31000424SS, ST32000444SS to BC2B
Fixes to improve robustness from certain read errors due to encroachment

- ST33000650SS to BC37
Fixes to improve overall robustness.

- ST1000NM0001, ST2000NM0001 to BC42
Inital Release

SAS 2.5" (SFF)

- ST9300605SS, ST9600205SS, ST9900805SS to B556
- ST9146853SS, ST9300653SS to B635
Fixes to improve overall robustness.

ST9300505SS to E552
ST9146753SS to E632
Initial Release

- ST9500620SS, ST91000640SS to BD26
Improve general robustness and added support for DPICZ

- HUC106030CSS60, HUC106060CSS60 to D340
Improve general robustness

- MBF2300RC, MBF2600RC to SB28
Improves performance in certain benchmarks

SATA 3.5"

- ST33000650NS to BB34
Fixes to improve overall robustness.

- ST1000NM0011, ST2000NM0011, ST500NM0011 to BB45
Initial Release

- ST3500514NS, ST31000524NS, ST32000644NS to BB29
Fixes for intermittent drive hangs

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB15
Added enhancement for improved robustness


SATA 2.5"

- ST9250610NS, ST9500620NS, ST91000640NS to BE24
Initial Release

- ST9160511NS, ST9500530NS to BE19
Fixes for overall robustness.


SATA 2.5" SSD

- STEC MACH8 IOPS to 2765
STEC M8PSB2 T4 to SM05
Fixes potential drive lock up during cold or warm boots
Fixes issues with RHEL 6.x installation

- SG9XCS2D200GEIBM to SA03SE6C
Fixes default drive VPD information for manufacturing,
the default LED behavior on certain systems and
fixes issues with client install thru VMWare 5.x

SATA 1.8" SSD

- STEC M8PSB1 to 0409
STEC M8PSB1 T4 to SM16
Fixes potential drive lock up during cold or warm boots
Fixes issues with RHEL 6.x installation

- SG9XCS1B50GMIBM to SA03SB6C
SASG9XCS1F200GEIBM to SA03SB6C
Fixes potential drive lock up during cold or warm boots and
the default LED behavior on certain systems and
fixes issues with client install thru VMWare 5.x

===========================================

Version 1.09
(Critical)

SAS 3.5"
Product ID FW

IBM-ESXSVPCA300900EST1 A3B8
IBM-ESXSVPCA450900EST1 A3B8
IBM-ESXSVPCA600900EST1 A3B8
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4C
IBM-ESXSST3300656SS BA4C
IBM-ESXSST3450856SS BA4C
IBM-ESXSST3300657SS BA58
IBM-ESXSST3450857SS BA58
IBM-ESXSST3600057SS BA58
IBM-ESXSST3750630SS BC1H
IBM-ESXSST31000640SS BC1H
IBM-ESXSST31000424SS BC28
IBM-ESXSST32000444SS BC28
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5" (SFF)
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST973402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53C
IBM-ESXSST9146803SS B53C
IBM-ESXSST9600204SS B548
IBM-ESXSST936751SS B617
IBM-ESXSST973451SS B617
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD22
IBM-ESXSST91000640SS BD22
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D2F8
IBM-ESXSHUC106060CSS60 D2F8
IBM-ESXSST9300503SS E536
IBM-ESXSST9146752SS E625
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMBF2300RC SB28
IBM-ESXSMBF2600RC SB28


IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107

SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WDC WD2502ABYS-23B7A0 02.03B06
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB14
ST3500320NS BB14
ST3750330NS BB14
ST31000340NS BB14
ST3500514NS BB28
ST31000524NS BB28
ST32000644NS BB28
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HDS721025CLA382 JP1OA3GE
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31
WD5003ABYX-23 WC31

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE18
ST9500530NS BE18
ST9250610NS BE21
ST9500620NS BE21
ST91000640NS BE21

SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2732
STEC M8PSB2 T4 SM04

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0408
STEC M8PSB1 T4 SM15
SG9XCS1B50GMIBM SA03SB63
SG9XCS1F200GEIBM SA03SB63


This package includes new updates to drives with product ID strings of:

SAS 3.5"

- ST31000424SS, ST32000444SS to BC28
Added enhancement for improved RV robustness

- MBE2073RC, MBE2147RC to SC17
- MBA3073RC, MBA3147RC, MBA3300RC to SA0A
Added VPD changes for manufacturing

SAS 2.5" (SFF)

- ST9300603SS, ST9146803SS to B53C
ST9600204SS to B548
SST973452SS, ST9146852SS to B62C
CBRCA146C3ETS0, CBRCA300C3ETS0 to C610
Added fixes for overall drive robustness

- MBD2147RC, MBD2300RC to SB1A
Added VPD changes for manufacturing
Addresses issues seen with DSA HDD Diagnostic test.

- MBF2300RC, MBF2600RC to SB25
Addresses issues seen with DSA HDD Diagnostic test.

- ST9500620SS, ST91000640SS to BD22
HUC106030CSS60, HUC106060CSS60 to D2F8
Inital Release

SATA 3.5"

- WD2502ABYS-23B7A0 , WD1602ABYS-23B7A0 to 02.03B07
Addresses firmware issues that may cause a drive to be marked defunct
prematurely under certain application workloads.

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB14
ST3500514NS, ST31000524NS, ST32000644NS to BB28
Added enhancement for improved robustness

- WD5003ABYX-23 to WC31
Initial Release

SATA 2.5"

- WD3000BLFS-23YBU0 to 04.04V10
(Critical)
Addresses firmware issues that may cause a drive to be marked defunct
prematurely under certain application workloads.


- ST9250610NS, ST9500620NS, ST91000640NS to BE21
Initial Release

SATA 2.5" SSD

- STEC MAC8 IOPS to 2732
STEC M8PSB2 T4 to SM04
Addresses an issue installing RHEL 6.0 onto this drive.

SATA 1.8" SSD

- SG9XCS1B50GMIBM, SG9XCS1F200GEIBM to SA03SB63
Addresses rare issue where the drive may not being seen on
power up.

- STEC M8PSB1 to 0408
STEC M8PSB1 T4 to SM15
Addresses an issue installing RHEL 6.0 onto this drive.

===============================================================

Version 1.08.01
(Critical)

SAS 3.5"
Product ID FW

VPCA300900EST1 A3B8
VPCA450900EST A3B8
VPCA600900EST1 A3B8
VPBA073C3ETS11 A496
VPBA146C3ETS11 A496
VPBA300C3ETS11 A496
VPBPA300C3EST1 A529
VPA036C3-ETS10 A650
VPA073C3-ETS10 A650
VPA146C3-ETS10 A650
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST373455SS BA2D
ST3146855SS BA2D
ST3300655SS BA2D
ST373355SS BA38
ST3146755SS BA38
ST3300555SS BA38
ST3146356SS BA4C
ST3300656SS BA4C
ST3450856SS BA4C
ST3300657SS BA58
ST3450757SS BA58
ST3600057SS BA58
ST3750630SS BC1G
ST31000640SS BC1G
ST31000424SS BC26
ST32000444SS BC26
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
MAU3036RC S902
MAU3073RC S902
MAU3147RC S902
MBA3073RC SA08
MBA3147RC SA08
MBA3300RC SA08
MAX3036RC T907
MAX3073RC T907
MAX3147RC T907


SAS 2.5" (SFF)
Product ID FW

ST936701SS B51D
ST973401SS B51D
ST936701SS B51D
ST973401SS B51D
ST973402SS B52B
ST9146802SS B52B
ST9300603SS B53B
ST9146803SS B53B
ST9600204SS B546
ST936751SS B617
ST973451SS B617
ST973452SS B629
ST9146852SS B629
ST9500430SS BD14
CBRCA146C3ETS0 C370
CBRCA300C3ETS0 C370
CBRBA073C3ETS0 C49C
CBRBA146C3ETS0 C49C
ST9300503SS E536
ST9146752SS E625
MAV2036RC S116
MAV2073RC S116
MBB2073RC SB07
MBB2147RC SB07
MBD2147RC SB19
MBD2300RC SB19
MBC2073RC SC06
MBE2073RC SC16
MBE2147RC SC16
MAY2036RC T107
MAY2073RC T107


SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB13
ST3500320NS BB13
ST3750330NS BB13
ST31000340NS BB13
ST3500514NS BB26
ST31000524NS BB26
ST32000644NS BB26
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
Hitachi HDT725025VLA3 V5DOA7CA
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
WDC WD2502ABYS-23B7A0 02.03B07
WD2502ABYS-23B7A0 02.03B07
WD802ABYS-23B7A0 02.03B05
WD1602ABYS-23B7A0 02.03B05
WD2003FYYS-23T8B0 01.00D04
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V09
ST9160511NS BE18
ST9500530NS BE18


SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2582

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0405


This package includes new updates to drives with product ID strings of:

SATA 3.5"

- WDC WD2502ABYS-23B7A0 and WD2502ABYS-23B7A0 to 02.03B07
Added enhanced background function to prevent premature
failure of the drive.



===============================================================

Version 1.08.00
(Critical)

SAS 3.5"

- ST373455SS, ST3146855SS, ST3300655SS to BA2D
- ST373355SS, ST3146755SS, ST3300555SS to BA38
- ST3146356SS, ST3300656SS, ST3450856SS to BA4C
- ST3300657SS, ST3450757SS, ST3600057SS to BA58
- ST3750630SS, ST31000640SS to BC1G
- ST31000424SS, ST32000444SS to BC26
(All Above Critical)
These codes addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

- MBA3073RC, MBA3147RC, MBA3300RC to SA08
This code corrects a firmware bug that may cause the drive to not
come ready on a cold boot.

SAS 2.5" (SFF)

- ST973402SS, ST9146802SS to B52B
- ST936751SS, ST973451SS to B617
- ST9146803SS, ST9300603SS toB53B
- ST9600204SS to B546
- ST973452SS, ST9146852SS to B629
- ST9300503SS to E536
- ST9146752SS to E625
- ST9500430SS to BD14
(All Above Critical)
These codes addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

SATA 3.5"

- ST3500514NS, ST31000524NS, ST32000644NS to BB26

- WD2003FYYS-23W0B0 to WA32
- WDC WD1003FBYX-23Y7B0 to WB31
Initial release


SATA 2.5" SSD

- STEC MACH8 IOPS to 2582 (Critical)
Corrects firmware bug that may cause data corruption.
For further information, please refer to retain tip H197650.

SATA 1.8" SSD

- STEC M8PSB1 to 0405 (Critical)
Corrects firmware bug that may cause data corruption.
For further information, please refer to retain tip H197650.


===============================================================

Version 1.07.01
(Critical)

Added support for the following controller:

- IBM 6Gb SSD HBA (68Y7362)

The following is a list of drives and the firmware that they will be
checked for and updated to as necessary.


SAS 3.5"
Product ID FW

VPCA300900EST1 A3B8
VPCA450900EST A3B8
VPCA600900EST1 A3B8
VPBA073C3ETS11 A496
VPBA146C3ETS11 A496
VPBA300C3ETS11 A496
VPBPA300C3EST1 A529
VPA036C3-ETS10 A650
VPA073C3-ETS10 A650
VPA146C3-ETS10 A650
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST373455SS BA2A
ST3146855SS BA2A
ST3300655SS BA2A
ST373355SS BA36
ST3146755SS BA36
ST3300555SS BA36
ST3146356SS BA4A
ST3300656SS BA4A
ST3450856SS BA4A
ST3300657SS BA56
ST3450757SS BA56
ST3600057SS BA56
ST3750630SS BC1E
ST31000640SS BC1E
ST31000424SS BC21
ST32000444SS BC21
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
MAU3036RC S902
MAU3073RC S902
MAU3147RC S902
MBA3073RC SA07
MBA3147RC SA07
MBA3300RC SA07
MAX3036RC T907
MAX3073RC T907
MAX3147RC T907


SAS 2.5" (SFF)
Product ID FW

ST936701SS B51D
ST973401SS B51D
ST936701SS B51D
ST973401SS B51D
ST973402SS B52A
ST9146802SS B52A
ST9300603SS B53A
ST9146803SS B53A
ST9600204SS B544
ST936751SS B616
ST973451SS B616
ST973452SS B626
ST9146852SS B626
ST9500430SS BD13
CBRCA146C3ETS0 C370
CBRCA300C3ETS0 C370
CBRBA073C3ETS0 C49C
CBRBA146C3ETS0 C49C
ST9300503SS E534
ST9146752SS E623
MAV2036RC S116
MAV2073RC S116
MBB2073RC SB07
MBB2147RC SB07
MBD2147RC SB19
MBD2300RC SB19
MBC2073RC SC06
MBE2073RC SC16
MBE2147RC SC16
MAY2036RC T107
MAY2073RC T107


SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
WD2003FYYS-23T8B0 01.00D04
WDC WD2502ABYS-23B7A0 02.03B05
WD2502ABYS-23B7A0 02.03B05
WD802ABYS-23B7A0 02.03B05
WD1602ABYS-23B7A0 02.03B05
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB13
ST3500320NS BB13
ST3750330NS BB13
ST31000340NS BB13
ST3500514NS BB26
ST31000524NS BB26
ST32000644NS BB26
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA


SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V09
ST9160511NS BE18
ST9500530NS BE18


SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2366

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0404


This package includes new updates to drives with product ID strings of:

SAS 3.5"

- VPCA300900EST1, VPCA450900EST, VPCA600900EST1 to A3B8
Initial Release

- VPBPA300C3EST1 to A529
Initial Release

- ST3300657SS, ST3450757SS, ST3600057SS to BA56
(Critical)
Performance improvements under certain workloads.
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.

- ST31000424SS, ST32000444SS to BC21
Initial Release


SAS 2.5" (SFF)

- ST9300603SS, ST9146803SS to B53A
(Critical)
Performance improvements under certain workloads.
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.

- ST9600204SS to B544
(Critical)
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.

- ST973452SS, ST9146852SS to B626
Performance improvements under certain workloads.

- ST9500430SS to BD13
Performance improvements under certain workloads

- ST9300503SS to E534 and ST9146752SS to E623
Performance improvements under certain workloads.

- MBD2147RC, MBD2300RC to SB19 (Critical)
MBE2073RC, MBE2147RC to SC16 (Critical)
Corrects a firmware bug that erroneously reported medium
errors which may cause the drive to report PFA alerts and
in some cases be marked offline

SATA 3.5"

- WDC WD2502ABYS-23B7A0, WD2502ABYS-23B7A0, WD802ABYS-23B7A0,
WD1602ABYS-23B7A0 to 02.03B05 (Critical)
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.


- ST3500514NS, ST31000524NS, ST32000544NS to BB26 (Critical)
This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB13
(Critical)
This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

- HUA722020ALA330 to JKAOA3GA
HUA722050CLA330 to JP2OA3GB
HUA722010CLA330 to JP4OA3GB
Initial Release

SATA 2.5"

- WD3000BLFS-23YBU0 to 04.04V09
(Critical)
This code corrects an additional issue where the drive may be
marked defunct.

- ST9160511NS, ST9500530NS to BE18 (Critical)
This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.
Also improves performance under certain workloads.


SATA 2.5" SSD

- STEC MACH8 IOPS to 2366 (critical)
Corrects firmware bug that may cause degraded performance
and in some cases the drive may not come ready after a warm or
old boot.

SATA 1.8" SSD

- STEC M8PSB1 to 0404
Turns the default for write cache off
Initial Release

===============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.06
(Critical)

Added support for the following controllers:

- IBM ServeRAID BR10il SAS controller v2 (49Y4731)
- IBM ServeRAID M1015 SAS controller (46M0831)
- IBM ServeRAID M5015 SAS controller (46M0829)
- IBM ServeRAID M5014 SAS controller (46M0916)

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- ST373455SS, ST3146855SS, ST3300655SS to BA2A
ST373355SS, ST3146755SS, ST3300555SS to BA36
(Critical)
These codes addresses a rare potential for data corruption. For this issue
to occur, the drive write cache must be enabled. When a write is issued
while the drive write cache is enabled and a read-verify is performed
immediately afterwards, undetected data corruption can occur. For further
information, please refer to retain tip H194632.

- ST3750630SS, ST31000640SS to BC1E
ST3146356SS, ST3300656SS, ST3450856SS to BA4A
This code address an issue where the drive may report an erroneous
hardware error to the controller.

- MBA3073RC, MBA3147RC, MBA3300RC to SA07
This code improves sequential write performance under certain workloads
when write cache is turned on.

- ST3300657SS, ST3450757SS, ST3600057SS to BA52
NOTE: This is the first code release to be included in the hard drive
update package.

SAS 2.5" (SFF)

- ST973402SS, ST9146802SS to B52A
ST936751SS, ST973451SS to B616
(Critical)
These codes addresses a rare potential for data corruption. For this issue
to occur, the drive write cache must be enabled. When a write is issued
while the drive write cache is enabled and a read-verify is performed
immediately afterwards, undetected data corruption can occur. For further
information, please refer to retain tip H194632.

- MBB2073RC, MBB2147RC to SB07
MBD2147RC, MBD2300RC to SB17
MBE2073RC, MBE2147RC to SC14
CBRCA146C3ETS0, CBRCA300C3ETS0 to C370
This code improves sequential write performance under certain workloads
when write cache is turned on.

- ST9500430SS to BD11
This is the first code release to be included in the hard drive
update package.

SATA 3.5"

- WD2003FYYS-23T8B0 to 01.00D04
This is the first code release to be included in the hard drive
update package.

SATA 2.5"

- WD3000BLFS-23YBU0 to 04.04V08
(Critical)
This code corrects an issue where the drive may generate a false PFA alert.
It also corrects an issue where the drive may be marked defunct

- ST9160511NS, ST9500530NS to BE16
This is the first code releases to be included in the hard drive
update package.

===============================================================
IBM SAS Hard Disk Drive Update Program
Version 1.05

SAS 2.5" (SFF)

ST9xxxx51SS to B616
ST9xxxx02SS to B52A
- This code improves the robustness of write cache operations.

ST9xxxx52SS to B624
ST9xxxx03SS to B536
- This code improves the robustness of write cache operations and
sequential write performance when write cache is enabled

MBD2xxxRC to SB14
- Initial release

SAS 3.5"

ST3xxxxx6SS to BA49
ST3750630SS to BC1D
- This code improves the robustness of write cache operations.

SATA 3.5"

WDC WD2502ABYSxxxxx tp 02.03B04
- Fixes incorrect VPD data

SATA 2.5"

WD3000xxxxx to 04.04V05
- Adjusted PHY setting for better signal quality margin.

SATA 2.5" SSD

STEC MACH8 IOPS to 2269
GBRL0xxxxx to 4.17
GBRLBxxxxx to 4.26
- The new firmware will correct a rare data error condition
in the drives where invalid data may be passed to the system
without any error condition flagged.

Due to the severity of this potential issue, IBM strongly
recommends applying this firmware as soon as possible.

For further information, please refer to retain tip H195663.
=================================================================

IBM SAS Hard Disk Drive Update Program
Version 1.04

SAS 2.5" (SFF)

CBRBAxxxxxx to C49B
- Modified VPD for JSxx Blades

MBBxxxxxx to SB05
- Fixed a performance issue when synchronizing or rebuilding an
array when used in a LSI 1064 based SAS controller

MBC2073RC to SC04
- Fixed a performance issue when synchronizing or rebuilding an
array when used in a LSI 1064 based SAS controller

SAS 3.5"

MBAxxxxxx to SA06
- Fixed a performance issue when synchronizing or rebuilding an
array when used in a LSI 1064 based SAS controller

ST3xxxxx6SS to BA48
- This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
When a write is issued while the drive write cache is
enabled and a read-verify is performed immediately afterwards,
undetected data corruption can occur.
For further information, please refer to retain tip H194632

ST3750630SS to BC1A
- This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
When a write is issued while the drive write cache is
enabled and a read-verify is performed immediately afterwards,
undetected data corruption can occur.
For further information, please refer to retain tip H194632

- Fixes a hang condition during failover operation on a
Bladecenter-S chassis with an RSSM controller.

BBAxxxxxx to BH0K
- Fixes an issue where a drive may prematurely report a PFA trip

GNAxxxxxx to BH0J
- Fixes an issue where a drive may prematurely report a PFA trip


SATA 3.5"

ST31000340NS, ST370330NS, ST3250310NS, ST3500320NS to BB12
- This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
When a write is issued while the drive write cache is
enabled and a read-verify is performed immediately afterwards,
undetected data corruption can occur.
For further information, please refer to retain tip H194632

- This code addresses a rare potential for data loss.
After a power cycle, the drive will no longer be available
and becomes unresponsive. Data will become inaccessible due to the
drive not responding.
For further information, please refer to retain tip H194623.


WDC WD2502ABYSxxxxx tp 02.03B04
- Fixes incorrect VPD data

SATA 2.5"

WD3000xxxxx to 04.04V04
- Fixes a Critical issue - IBM recommends a backup of the data
on the drive before attempting to update the firmware.
This is a fix for an issue where data required for spinup of the
drive may be overwritten rendering the drive inoperable on a
subsequent warm or cold system reboot.

- Fixes a issue with an internal timer that may cause drive to
go offline when used in a non-raid environment.

SATA 2.5" SSD

STEC MACH8 IOPS to 2103
- Initial Release

=================================================================

IBM SAS Hard Disk Drive Update Program
Version 1.03

Added support for the following controllers:

IBM ServeRAID MR10il SAS Controller
IBM ServeRAID MR10is SAS Controller
IBM ServeRAID BR10i SAS Controller
IBM ServeRAID BR10il SAS/SATA Controller
IBM SAS/SATA RAID Kit
IBM SAS Expansion Card (CFFv) for IBM BladeCenter
IBM SAS Connectivity Card (CFFv) for IBM BladeCenter

New updates to drives with product ID strings of:

SAS 2.5" (SFF)

ST9146802SS, ST973402SS to B529
- Added support for JS2x Blades in a Bladecenter-S chassis
- Picked up the latest network roll of firmware fixes to
address some unexpected system hangs,

ST936751SS, ST973451SS to B615
- Added support for JS2x Blades in a Bladecenter-S chassis
- Picked up the latest network roll of firmware fixes to
address some unexpected system hangs,

CBRBAxxxxxx to C495
- Initial release

MBBxxxxxx to SB04
- Initial release

MBC2073RC to SC03
- Initial release

SAS 3.5"

VPBAxxxxxx to A496
- Added support for JS2x Blades in a Bladecenter-S chassis

ST3146855SS, ST3300655SS, ST373455SS to BA29
- Added support for JS2x Blades in a Bladecenter-S chassis
- Picked up the latest network roll of firmware fixes to
address some unexpected system hangs,

ST3450856SS to BA47
- IBM was notified by our vendor that there is a defect in
a level of firmware used in the IBM 450GB 15K SAS 3.5" HS HDD
(PN 41Y8454) in option 42D0519, which under certain conditions
may lead to data being written or read back incorrectly on the
drive. IBM has worked closely with the vendor to identify the
problem and developed a firmware fix to resolve the problem.
Customers should upgrade to firmware level BA47

MBAxxxxxx to SA05
- Initial release

ST3750630SS to BC17
- Initial release


SATA 3.5"

ST3250620NS, ST3500630NS, ST3750640NS to 3.AEV

ST3250621NS, ST3500631NS, ST3750641NS to 4AEV

ST31000340NS, ST3750330NS, ST3250310NS, ST3500320NS to BB10
- Initial release

HUA721050KLA330, HUA721075KLA330, HUA721010KLA330, to AB4A
- Initial Release

SATA 2.5" SSD

GBRL001xxx, GBRL0031xxx to 4.14
- corrects intermittent hangs during operations
=============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.02

Support of ServeRaid 8s Raid controller
Support of ServeRaid 10i Raid controller
Support of ServeRaid 10k Raid controller
Support of ServeRaid 10m Raid controller
Support of LSI 1078 SAS controller
Support of SATA drives attached to SAS controllers

Support and updates to drives with product ID strings of:

VPAxxxxxx to A650
Change to improve performance in sequential write workloads
Improvements to internal drive logging and media checking.
Critical Fix:
This code addresses a rare potential for data loss
This code update should be applied to prevent the event from occurring.

ST340XXXAS and ST380XXXAS to 3.48
Fix to address Read Log Command abort error.

ST340XXXAS, ST380XXXAS and ST3160XXXAS to 3.05
Fix to address intermittent hard drive no-shows
after system comes out of hibernation.

ST3500641NS to 3.AES
Changes to the refresh rate of the DRAM used on the drive.

ST3500640NS to 3.AEJ
Initial release.

HDTXX... & HDSXX... codes go to Masked ROM version.
HDS725050KLA360 to AQ1A to also
Fix an issue that occurs while running in NCQ mode with
write cache disabled.

ST3xxxx4SS to BA26
Improves intialization times with some ServeRaid controllers
Performance improvements under some sequential workloads.

ST3xxxx5SS to BA35
Improves intialization times with some ServeRaid controllers

ST9xxx51SS to B612
Intial release of firmware

ST9xxxx2SS to B526
Improves intialization times with some ServeRaid controllers

MAUxxxx and MAXxxxx
Added support for new SAS features required by new SAS controllers.

==============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.01
Please refer to RETAIN tip H186019.

Support of ServeRaid 8e Raid controller
Support of ServeRaid 8k Raid controller
Support of ServeRaid 8l Raid controller
Support of on-board LSI 1064 controller
IBM MegaRaid 8480 Raid Controller

Firmware updates to drives with Product ID strings:

GNAxxxx and BBAxxxx to BH0G
Picks up the latest network roll of firmware fixes
to improve performance under some sequential workloads
and improvements to signal quality parameters.

ST9xxxx to B51D amd ST3xxxx to BA18
Picks the latest network roll of firmware fixes
to address unexpected system hangs and some
performance improvements.

MAVxxxx to S116 and MAYxxxx to T107
Picks up the latest network roll of firmware fixes
and to improve signal quality parameters.

MAXxxxx to T904
Initial release
============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.00
Initial Release

Support of Adaptec 48xxx based controllers
Support of ServeRaid 8i Raid controller
Support and updates to drives with product ID strings of:
ST936701SS
ST973401SS
ST336754SS
ST373454SS
GNAxxxxx
BBAXXXXX

ibm_fw_hddlenovo_sas-1_23_00_linux_32-64_chg

IBM System x3850/x3950 X5/MAX5 uEFI Flash Update
Version 1.85 (BuildID G0E185A)
Change History

Version 1.85 - BuildID: G0E185A - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Fixed excessive single bit memory errors reporting by mcelog daemon in Linux, refer to Retain TIP H214338 for details.
- Eliminate unnecessary TPM error messages under Linux OS, refer to Retain TIP H91112 for details.
Enhancements:
- None
Limitations:
-Limited Solaris 10 operating system support, refer to RETAIN Tip H212469 for details.
Dependencies:
- IMM YUOOG8C (Version 1.48) or later is required.
- FPGA G0UD92B (Version 5.02) or later is required.


Version 1.83 - BuildID: G0E183B - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Fix uEFI iSCSI inconsistent configuration after reboot
Enhancements:
- None
Limitations:

Dependencies:
- IMM YUOOG6C (Version 1.44) or later is required.
- FPGA G0UD92B (Version 5.02) or later is required.

Version 1.83 - BuildID: G0E183A - Suggested
-----------------------------------------------------
Problem(s) Fixed:
- Add description of specific error code in system event logs when memory correctable errors happens
- Update the information of memory pair entries for uncorrectable memory errors
Enhancements:
- None
Limitations:

Dependencies:
- IMM YUOOG6A (Version 1.43) or later is required.
- FPGA G0UD92B (Version 5.02) or later is required.

Version 1.81 - BuildID: G0E181B - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Power off the server after N boot attempts without locating a boot device
- Add Scrub Failure message in IMM log for Data Queue memory training failures during POST. Please refer to RETAIN Tip H211626 for details.
- Optimized MAX5 chipset settings to avoid reset in EXA-scaled configurations
Enhancements:
- None
Limitations:

Dependencies:
- IMM YUOOG2C (Version 1.42) or later is required.
- FPGA G0UD92B (Version 5.02) or later is required.


Version 1.79 - BuildID: G0E179B - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Addressed Intel errata BP57 and BA138 System Resets with 32-bit (PAE Enabled) Guest OS and VT FlexPriority Enabled. For more information, refer to IBM RETAIN Tip H21370

Enhancements:
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000037
- Update microcode for Intel Xeon 7500 series processors to M04206E6_0000000A

Limitations:

Dependencies:
- IMM YUOOF7C (Version 1.41) or later is required.
- FPGA G0UD91A (Version 5.01) or later is required.


Version 1.79 - BuildID: G0E179A - Critical
-----------------------------------------------------
Problem(s) Fixed:

Enhancements:
- Add notification and recovery option when UEFI detects GPT corruption during POST. Please refer to RETAIN Tip H21166 for details.
- Add IPV6 PXE support.
- Optimized Memory Single Bit Thresholds.

Limitations:

Dependencies:
- IMM YUOOF7A (Version 1.40) or later is required.
- FPGA G0UD88B (Version 4.01) or later is required.


Version 1.77 - BuildID: G0E177A - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Limits C-states to avoid CPU VRD failures. Please refer to RETAIN Tip H207008 at the following link: http://www.ibm.com/systems/support/supportsite.wss/docdisplay?brandind=5000008&lndocid=MIGR-5091926
- Fix incorrect memory size report in F1 setup/OS when unusable DIMM was detected and isolated.
- Fix disk data corruption with LUNS greater than 2TB for QLogic HBA Cards.
- Fix F1 setup storage option missing issue for QLogic HBA card.
- Fix initial values selected in the "Custom" operating mode are not the same as the previously selected preset operating mode.

Enhancements:
- Add _WDG ACPI method support for SRIOV.
- Add PCI-SIG resizable BAR capability support.
- Support memory sparing function on a 2-nodes QPI linked system.

Limitations:

Dependencies:
- IMM YUOOF2A (Version 1.36) or later is required.
- FPGA G0UD87C (Version 4.00) or later is required.


Version 1.75 - BuildID: G0E175B - Critical
-------------------------------------------------
Problem(s) Fixed:
- Resolve OS or POST hang following a corrected machine check event.
- Don't enable secondary video adapters in pre-boot environment
to prevent Legacy VGA I/O conflict in Windows.
- Fix boot fail when using WOL.
- Addressed Intel errata BP47 and BA131 with title
"A Load May Appear to be Ordered Before an Earlier Locked Instruction".

Enhancements:
- Add Setup Option to select MM Config Base (1GB/2GB(default)/3GB).
- Optimize PCI Resource Allocation for Onboard Devices to make more
Legacy I/O and MMIO space available to Adapters.
- Add setup option to set VLAN ID.
- Add infinite boot loop option in F1 SETUP for legacy boot.
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000036.
- Update microcode for Intel Xeon 7500 series processors to M05206E6_00000009.

Limitations:

Dependencies:
- IMM YUOOE3C (Version 1.33) or later is required.
- FPGA G0UD82B (Version 2.03) or later is required.


Version 1.73 - BuildID: G0E173B - Suggested
-------------------------------------------------
IMPORTANT: IMM firmware YUOOD4G (Version 1.32) and FPGA firmware G0UD81B (Version
2.02) or later must be used in conjunction with this UEFI release. Please make sure
the current IMM firmware level is Version 1.32 or later before you update the UEFI
firmware.

Problem(s) Fixed:
- Fix uEFI.UEFIRomDisable setting for secondary nodes.
- Reset 3x Boot fail count upon any successful boot with user settings.
- Make PCI Slot instance unique across nodes in SMBIOS Type 9 structures.
- Fix VMWare Boot fail after installing it in UEFI mode.
- Fix Processor Details in UEFI F1 Setup for CPUs with non-zero PBSP.
- Fix system hang due to unhandled correctable SMI link event.

Enhancements:
- Disable entire Secondary I/O Hub, if all it's Slots (1-to-4) are disabled.
- Differentiate between QPI Link Width Reduction to Half vs Quarter Width.
- Add support for Netlist DIMMs in SMBIOS Type 17 structures.
- Add support for more than 255 PFs in Legacy MPS table.
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000034.
- Support add-in video adapters behind Legacy I/O Hub Slots as Legacy VGA.
- Add Setup Option to make 3x Boot fail configurable as Nx Boot fail.
- Sync uEFI.RomOrder with the available devices in hardware configuration.

Limitations:
Dependencies:
- IMM YUOOD4G (Version 1.32) or later is required.
- FPGA G0UD81B (Version 2.02) or later is required.


Version 1.71 - BuildID: G0E171A - Critical
-------------------------------------------------
IMPORTANT: IMM firmware YUOOC7E (Version 1.30) and FPGA firmware G0UD72B (Version
2.01) or later must be used in conjunction with this UEFI release. Please make sure
the current IMM firmware level is Version 1.30 or later before you update the UEFI
firmware.

Problem(s) Fixed:
- Fix false Three 3x Boot fail following replacement of battery.
- Fix IMM MAC Address display in F1 IMM page.
- Fix uEFI.VideoSelect default setting.

Enhancements:
- Add support for 32GB DIMM.
- Don't check for Legacy Option ROM Errors, when it is Disabled.
- Update to SMBIOS 2.7 for extended DIMM size and Address space support.
- F1 Network page update: categorized & consistent MAC notation.
- Support Directory Assisted Snoop with Intel Xeon E7 series processors.
- Describe I/O Affinity based on Setup Option of Non-Pooled (default) vs Pooled.
- Add Setup Option to enable MMIO allocation above 4GB for large configuration.
- Include MD5 checksum into firmware update package to prevent corrupted update.
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000032.
- Improve Software Algorithms for Memory Robustness.
- Limit boot attempts, when no bootable devices are found.
- Add support for more than 2.2 TB disks with GPT.
- Add Setup Option to disable the native control of PCI Express features from OS.

Limitations:
Dependencies:
- IMM YUOOC7E (Version 1.30) or later is required.
- FPGA G0UD72B (Version 2.01) or later is required.


Version 1.60 - BuildID: G0E160B - Critical
-------------------------------------------------
Version 1.60 is a major update release to support MAX5 multi node and also
includes recommended updates for other single & multi node configurations.

IMPORTANT: IMM firmware YUOOB7C (Version 1.28) and FPGA firmware G0UD62C (Version
2.00) or later must be used in conjunction with this UEFI release. Please make sure
the current IMM firmware level is Version 1.28 or later before you update the UEFI
firmware.

Problem(s) Fixed:
- When an SMI Lane Failover or SMI Link Failure event is detected during POST,
the incorrect card number was shown in the POST Event Viewer log.
- After a three times boot failure, scrolling the setup screens would leave
garbled characters at the bottom of the screen.
- Windows PE 32bit would boot without any PCI devices configured including
USB keyboard and mouse.
- WHEA corrected error events are being logged without corresponding IMM
events.
- Adapter with 512MB MMIO requirement installed in slots 1-4 reports a
resource conflict.

Enhancements:
- This release supports Machine Type 7145 or 7146 with Intel Xeon 7500 series
processor, as well as, Machine Type 7143 and 7191 with Intel Xeon E7 series
processors.
- Added support for UEFI PXE boot in IPv6 environment.
- Updated microcode for Intel Xeon E7 series processors to M05206F2_00000030.
- Updated Intel Memory and QPI Reference Code to Version 2.11.

Limitations:
- With the new default setting, the 2nd port of onboard Ethernet cannot be used
for the legacy PXE boot. To legacy PXE boot from the 2nd port, enable the
legacy option ROM for it.
- After upgrading to this release internet Small Computer System Interface
(iSCSI) devices configured to be bootable will no longer be bootable.
Use the UEFI F1 Setup to reconfigure the iSCSI devices to work around
this issue.

Dependencies:
- IMM YUOOB7C (Version 1.28) or later is required.
- FPGA G0UD62C (Version 2.00) or later is required.


Version 1.50 - BuildID: G0E152B - Critical
-------------------------------------------------
Version 1.50 is a release for Machine Type 7143 and 7191 with Intel Xeon E7 series
processors.

IMPORTANT: IMM firmware YUOOA6A (Version 1.26) and FPGA firmware G0UD57A (Version
1.05) or later must be used in conjunction with this UEFI release. Please make sure
the current IMM firmware level is Version 1.26 or later before you update the UEFI
firmware.

Problem(s) Fixed:
- Microsoft Windows truncated memory dump file in EFI boot mode because the
number of memory regions in EFI memory map was exceeding the limit of Windows.
The problem was caused by fragmentation of EFI memory regions.
- After three consecutive UEFI boot failures, UEFI setup settings were changed
to default settings.
- Corrected memory error WHEA events were incorrectly logged in the Windows
system event log.
- When add-in video adapter was installed in PCI-Express slot 1, UEFI Version
1.40 failed to boot.
- Moving power-on password override jumper (J29 on I/O board) could not bypass
the power-on-password prompt when UEFI Version 1.40 was installed.
- Fixed detection of DIMM replacement and automatic reenabling of disabled DIMM.

Enhancements:
- Added error reporting to inform when the legacy option ROM space is not enough
to execute the option ROMs of all PCI adapters during legacy boot.
- In order to reduce the chance of the legacy option ROM space error, the legacy
option ROM execution order was changed so that onboard SAS option ROM will be
executed earlier than onboard Ethernet option ROM. (Some of SAS adapters have
option ROMs which comply with PCI firmware specification 2.1 while onboard
Ethernet has option ROM which complies with PCI firmware specification 3.0.)
- Updated Broadcom firmware to Version T6.2.4.1.
- Added Extended APIC (X2APIC) support and a setup menu to enable or disable the
Extended APIC.

Limitations:
- This release does not support Machine Type 7145 or 7146 with Intel Xeon 7500
series processors yet, but supports only Machine Type 7143 and 7191 with Intel
Xeon E7 series processors.

Dependencies:
- IMM YUOOA6A (Version 1.26) or later is required.
- FPGA G0UD57A (Version 1.05) or later is required.


Version 1.40 - BuildID: G0E140A - Suggested
-------------------------------------------------
IMPORTANT: IMM firmware YUOO91D (Version 1.24) and FPGA firmware G0UD44D (Version
1.04) or later must be used in conjunction with this UEFI release. Please make sure
the current IMM firmware level is Version 1.24 or later before you update the UEFI
firmware.

Problem(s) Fixed:
- Fixed a potential POST (Power-on-Self-Test) hang which might occur during
recalibrating system power before OS starts.
- Memory patrol scrub option was not functioning. The problem was corrected
by updating Intel processor microcode and RAS code.
- Redundant Bit Steering feature was not working for DIMMs greater than single
rank in MAX5 memory expansion unit.
- Red Hat Enterprise Linux 6 (RHEL6) installation could not be continued
due to a video problem with EFI console output.
- Disable propagation of Intel VT-d faults as fatal errors to avoid guest
VM to cause the entire system to crash.

Enhancements:
- Increase cooling fan speed if Fusion-io SSD PCI adapter is installed.
- Added Advanced IMM Network Setup option to select data rate and duplex mode
settings.

Limitations:
Dependencies:
- IMM firmware YUOO91D (Version 1.24) or later is required.
- FPGA firmware G0UD44D (Version 1.04) or later is required.


Version 1.32 - BuildID: G0E131A - Critical
-------------------------------------------------
Version 1.32 is a major update release to support MAX5 memory expansion and also
includes recommended updates for single & multi node configurations.

IMPORTANT: IMM firmware YUOO75P (Version 1.19) and FPGA firmware G0UD43A (Version
1.02) or later must be used in conjunction with this UEFI release. Please make sure
the current IMM firmware level is Version 1.19 or later before you update the UEFI
firmware.

Problem(s) Fixed:
- Fixed a potential problem with unexpected QPI inband resets when QPI link is
running at 6.4GT/s.
- There was incorrect data in MPS table which is used by legacy OS.
- Fixed a PCI memory mapped I/O resource allocation issue where Broadcom network
controller settings are overlaid causing invalid PCI Address ranges to appear
to OS. The problem was caused by Broadcom firmware prior to Version T5.2.4.7
(Broadcom uEFI driver Version 5.2.15).
- Fixed DMAR table for Intel Virtualization Technology for Directed I/O (Vt-d)
with explicitly describing all PCI devices under the secondary root PCI bus.

Enhancements:
- Enabled MAX5 memory expansion in single node configuration with maximum 1.5TB
memory.
- Added "Halt On Severe Error" setup option in Operating Modes setup menu which
can prevent the system from booting into OS and shows POST Event Viewer if
POST detects a severe error that caused an unexpected reboot.

Limitations:
Dependencies:
- IMM firmware YUOO75P (Version 1.19) or later is required.
- FPGA firmware G0UD43A (Version 1.02) or later is required.


Version 1.23 - BuildID: G0E122D - Critical
-------------------------------------------------
Version 1.23 is a major update release to support multi node configuration and also
includes critical updates for single node configuration.

IMPORTANT: IMM firmware YUOO73K (Version 1.14) and FPGA firmware G0UD29C (Version
1.01) or later must be used in conjunction with this UEFI release. Please make sure
the current IMM firmware level is Version 1.14 or later before you update the UEFI
firmware.

Problem(s) Fixed:
- Fixed risk of data errors when using firmware SCSI stack on Block I/O devices
which are greater than 2TB with a GPT partition. (Please refer to RETAIN Tip
H16222, MIGR-5084554 uEFI systems with HBA and > 2 TB LUN may have data
consistency errors - IBM Servers.)
- Mellanox InfiniBand adapter disappears after warm-reset.
- Memory cards may not be correctly recognized or initialized after a reset
due to a race condition during the memory card initialization.
- Potential memory error occurring at 978MT/s speed due to an incorrect DIMM
register setting.
- Intermittent QPI lane width reduction events that could result in software
NMI resets when PCI-Express bus is stressed.
- Performance problem with legacy PXE network boot. The problem was caused by
the onboard Broadcom network controller firmware prior to Version T5.2.4.4.
- PCI-Express link training problem with some adapters which support Gen2
speed.

Enhancements:
- Enabled multi node configuration, maximum 8 CPU sockets (128 logical CPUs) and
maximum 2TB memory.
- Enabled Intel Virtualization Technology for Directed I/O (Vt-d).
- Improved link stability for PCI-Express root ports and QPI (Intel QuickPath
Interconnect).

Limitations:
Dependencies:
- IMM firmware YUOO73K (Version 1.14) or later is required.
- FPGA firmware G0UD29C (Version 1.01) or later is required.


Version 1.02 - BuildID: G0E107D - Critical
-------------------------------------------------
Problem(s) Fixed:
- Fixed an NMI problem caused by a downlevel firmware of ServeRAID M5015 SAS/SATA
adapter (46M0829). This change reports the downlevel firmware and adjusts error
reporting to allow the system boot to the firmware update, also allows unattended
firmware update.
- Fixed a problem which mistakenly reports a double bit memory error and disables
the memory DIMMs.
- Changed the UEFI BIOS default setting for processor C-state (ACPI C3) to disable
in Performance mode and Custom mode.

Enhancements:
Limitations:
Dependencies:


Version 1.00 - BuildID: G0E107B (Initial Release)
-------------------------------------------------
Problem(s) Fixed:
Enhancements:
Limitations:
Dependencies:

ibm_fw_uefi_g0e185a-1_85_linux_32-64_chg

IBM System x3690 X5/MAX5 uEFI Flash Update
Version 1.85 (BuildID MLE185A)
Change History

Version 1.85 - BuildID: MLE185A - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Fixed excessive single bit memory errors reporting by mcelog daemon in Linux, refer to Retain TIP H214338 for details.
- Eliminate unnecessary TPM error messages under Linux OS, refer to Retain TIP H91112 for details.
Enhancements:
- None
Limitations:
-Limited Solaris 10 operating system support, refer to RETAIN Tip H212469 for details.
Dependencies:
- IMM YUOOG8C (Version 1.48) or later is required.
- FPGA MLUD33F (Version 1.23) or later is required.


Version 1.83 - BuildID: MLE183B - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Fix uEFI iSCSI inconsistent configuration after reboot
Enhancements:
- None
Limitations:

Dependencies:
- IMM YUOOG6C (Version 1.44) or later is required.
- FPGA MLUD33F (Version 1.23) or later is required.

Version 1.83 - BuildID: MLE183A - Suggested
-----------------------------------------------------
Problem(s) Fixed:
- Add description of specific error code in system event logs when memory correctable errors happens
- Update the information of memory pair entries for uncorrectable memory errors
Enhancements:
- None
Limitations:

Dependencies:
- IMM YUOOG6A (Version 1.43) or later is required.
- FPGA MLUD33F (Version 1.23) or later is required.

Version 1.81 - BuildID: MLE181B - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Power off the server after N boot attempts without locating a boot device.
- Add Scrub Failure message in IMM log for Data Queue memory training failures during POST. Please refer to RETAIN Tip H211626 for details.

Enhancements:
- None
Limitations:

Dependencies:
- IMM YUOOG2C (Version 1.42) or later is required.
- FPGA MLUD33E (Version 1.23) or later is required.


Version 1.79 - BuildID: MLE179B - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Addressed Intel errata BP57 and BA138 System Resets with 32-bit (PAE Enabled) Guest OS and VT FlexPriority Enabled. For more information, refer to IBM RETAIN Tip H21370

Enhancements:
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000037
- Update microcode for Intel Xeon 7500 series processors to M04206E6_0000000A

Limitations:

Dependencies:
- IMM YUOOF7C (Version 1.41) or later is required.
- FPGA MLUD33D (Version 1.23) or later is required.


Version 1.79 - BuildID: MLE179A - Critical
-----------------------------------------------------
Problem(s) Fixed:

Enhancements:
- Add notification and recovery option when UEFI detects GPT corruption during POST. Please refer to RETAIN Tip H21166 for details.
- Add IPV6 PXE support.
- Optimized Memory Single Bit Thresholds.

Limitations:

Dependencies:
- IMM YUOOF7A (Version 1.40) or later is required.
- FPGA MLUD33D (Version 1.23) or later is required.


Version 1.77 - BuildID: MLE177A - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Fix incorrect memory size report in F1 setup/OS when unusable DIMM was detected and isolated.
- Fix disk data corruption with LUNS greater than 2TB for QLogic HBA Cards.
- Fix F1 setup storage option missing issue for QLogic HBA card.
- Fix initial values selected in the "Custom" operating mode are not the same as the previously selected preset operating mode.

Enhancements:
- Add _WDG ACPI method support for SRIOV.
- Add PCI-SIG resizable BAR capability support.

Limitations:

Dependencies:
- IMM YUOOF2A (Version 1.36) or later is required.
- FPGA MLUD33C (Version 1.23) or later is required.


Version 1.75 - BuildID: MLE175B - Critical
-----------------------------------------------------
Problem(s) Fixed:
- Resolve OS or POST hang following a corrected machine check event.
- Don't enable secondary video adapters in pre-boot environment
to prevent Legacy VGA I/O conflict in Windows.
- Fix CPU VRD errors on MT 7148 and MT 7149.
- Fix boot fail when using WOL.
- Addressed Intel errata BP47 and BA131 with title
"A Load May Appear to be Ordered Before an Earlier Locked Instruction".

Enhancements:
- Add Setup Option to select MM Config Base (1GB/2GB(default)/3GB).
- Optimize PCI Resource Allocation for Onboard Devices to make more
Legacy I/O and MMIO space available to Adapters.
- Add setup option to set VLAN ID.
- Add infinite boot loop option in F1 SETUP for legacy boot.
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000036.
- Update microcode for Intel Xeon 7500 series processors to M05206E6_00000009.

Limitations:

Dependencies:
- IMM YUOOE3C (Version 1.33) or later is required.
- FPGA MLUD32D (Version 1.23) or later is required.


Version 1.73 - BuildID: MLE173B - Suggested
-----------------------------------------------------
Problem(s) Fixed:

- Reset 3x Boot fail count upon any successful boot with user settings.
- Fix PCI Slot usage field in SMBIOS Type 9 structures.
- Select first scanned from available add-in video adapters as Legacy VGA.
- Fix VMWare Boot fail after installing it in UEFI mode.
- Fix Processor Details in UEFI F1 Setup for CPUs with non-zero PBSP.
- Fix system hang due to unhandled correctable SMI link event.

Enhancements:

- Differentiate between QPI Link Width Reduction to Half vs Quarter Width.
- Add support for Netlist DIMMs in SMBIOS Type 17 structures.
- Add support for more than 255 PFs in Legacy MPS table.
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000034.
- Add Setup Option to make 3x Boot fail configurable as Nx Boot fail.
- Sync uEFI.RomOrder with the available devices in hardware configuration.

Limitations:

Dependencies:

- IMM YUOOD4G (Version 1.32) or later is required.
- FPGA MLUD32B (Version 1.22) or later is required.


Version 1.70 - BuildID: MLE170C - Critical
---------------------------------------
Problem(s) Fixed:

- Fix false Three 3x Boot fail following replacement of battery.
- Fix IMM MAC Address display in F1 IMM page.

Enhancements:

- Add support for 32GB DIMM.
- Don't check for Legacy Option ROM Errors, when it is Disabled.
- Update to SMBIOS 2.7 for extended DIMM size and Address space support.
- F1 Network page update: categorized & consistent MAC notation.
- Support Directory Assisted Snoop with Intel Xeon E7 series processors.
- Describe I/O Affinity based on Setup Option of Non-Pooled (default) vs Pooled.
- Add Setup Option to enable MMIO allocation above 4GB for large configuration.
- Include MD5 checksum into firmware update package to prevent corrupted update.
- Update microcode for Intel Xeon E7 series processors to M05206F2_00000032.
- Improve Software Algorithms for Memory Robustness.
- Limit boot attempts, when no bootable devices are found.
- Add support for more than 2.2 TB disks with GPT.
- Add Setup Option to disable the native control of PCI Express features from OS.

Limitations:

Dependencies:

- IMM YUOOC7E (Version 1.30) or later is required.
- FPGA MLUD31G (Version 1.21) or later is required.


Version 1.60 - BuildID: MLE160A - Critical
-----------------------------------------------------
Problem(s) Fixed:

- The system would boot with memory errors when memory mirroring was enabled.
- After a three times boot failure, scrolling the setup screens would leave
garbled characters at the bottom of the screen.
- Windows PE 32bit would boot without any PCI devices configured including
USB keyboard and mouse.
- WHEA corrected error events are being logged without corresponding IMM
events.

Enhancements:

- This release supports Machine Type 7148 or 7149 with Intel Xeon 7500
or 6500 series processors, as well as, supports Machine Type 7192 and 7147
with Intel Xeon E7 series processors.
- Enabled support for early power on by IMM.
- Added support for UEFI PXE boot in IPv6 environment.
- Updated microcode for Intel Xeon E7 series processors to M05206F2_00000030.
- Updated Intel Memory and QPI Reference Code to Version 2.11.

Limitations:

- After upgrading to this release internet Small Computer System Interface
(iSCSI) devices configured to be bootable will no longer be bootable.
Use the UEFI F1 Setup to reconfigure the iSCSI devices to work around
this issue.

Dependencies:

- IMM YUOOB7C (Version 1.28) or later is required.
- FPGA MLUD30J (Version 1.20) or later is required.


Version 1.40 - BuildID: MLE142A - Critical
---------------------------------------
Version 1.40 is a release for Machine Type 7192 and 7147 with Intel Xeon E7 series
processors.

IMPORTANT: IMM firmware YUOOA6A (Version 1.26) and FPGA firmware MLUD30G (Version
1.20) or later must be used in conjunction with this UEFI release. Please make
sure the current IMM firmware level is Version 1.26 or later before you update the
UEFI firmware.


Problem(s) Fixed:

- Microsoft Windows truncated memory dump file in EFI boot mode because the
number of memory regions in EFI memory map was exceeding the limit of Windows.
The problem was caused by fragmentation of EFI memory regions.
- After three consecutive UEFI boot failures, UEFI setup settings were changed
to default settings.
- Corrected memory error WHEA events were incorrectly logged in the Windows
system event log.
- Fixed detection of DIMM replacement and automatic reenabling of disabled DIMM.

Enhancements:

- Added error reporting to inform when the legacy option ROM space is not enough
to execute the option ROMs of all PCI adapters during legacy boot.
- In order to reduce the chance of the legacy option ROM space error, the legacy
option ROM execution order was changed so that onboard SAS option ROM will be
executed earlier than onboard Ethernet option ROM. (Some of SAS adapters have
option ROMs which comply with PCI firmware specification 2.1 while onboard
Ethernet has option ROM which complies with PCI firmware specification 3.0.)
- Updated Broadcom firmware to Version T6.2.4.1.
- Added Extended APIC (X2APIC) support and a setup menu to enable or disable the
Extended APIC.

Limitations:

- This release does not support Machine Type 7148 or 7149 with Intel Xeon 7500
or 6500 series processors yet, but supports only Machine Type 7192 and 7147
with Intel Xeon E7 series processors.

Dependencies:

- IMM YUOOA6A (Version 1.26) or later is required.
- FPGA MLUD30G (Version 1.20) or later is required.


Version 1.31 - BuildID: MLE131A - Critical
---------------------------------------
Problem(s) Fixed:

- SATA DVD drive may not be detected correctly. The problem was caused by
incorrect ICH10 SATA controller setting which decreased SATA transmitter
output voltage.

Enhancements:

Limitations:

Dependencies:


Version 1.30 - BuildID: MLE130A - Critical
---------------------------------------
Problem(s) Fixed:

- Fixed a potential POST (Power-on-Self-Test) hang which might occur during
recalibrating system power before OS starts.
- Memory patrol scrub option was not functioning. The problem was corrected
by updating Intel processor microcode and RAS code.
- Redundant Bit Steering feature was not working for DIMMs greater than single
rank in MAX5 memory expansion unit.
- Red Hat Enterprise Linux 6 (RHEL6) installation could not be continued
due to a video problem with EFI console output.
- Disable propagation of Intel VT-d faults as fatal errors to avoid guest
VM to cause the entire system to crash.

Enhancements:

- Added Advanced IMM Network Setup option to select data rate and duplex mode
settings.
- Updated Broadcom firmware to Version T6.0.4.2.

Limitations:

Dependencies:


Version 1.22 - BuildID: MLE120C - Initial Release
-----------------------------------------------------
Problem(s) Fixed:

- Fixed a potential problem with unexpected QPI inband resets when QPI link is
running at 6.4GT/s.
- There was incorrect data in MPS table which is used by legacy OS.
- Fixed a PCI memory mapped I/O resource allocation issue where Broadcom network
controller settings are overlaid causing invalid PCI Address ranges to appear
to OS. The problem was caused by Broadcom firmware prior to Version T5.2.4.7
(Broadcom uEFI driver Version 5.2.15).
- Fixed DMAR table for Intel Virtualization Technology for Directed I/O (Vt-d)
with explicitly describing all PCI devices under the secondary root PCI bus.

Enhancements:

- Enabled MAX5 memory expansion with maximum 1TB memory.
- Added "Halt On Severe Error" setup option in Operating Modes setup menu which
can prevent the system from booting into OS and shows POST Event Viewer if
POST detects a severe error that caused an unexpected reboot.
- Automatically switch to add-in video adapter from the onboard video controller
with setup default setting if add-in video adapter is installed.

Limitations:

Dependencies:


Version 1.00 - BuildID: MLE105C - Initial Release
-----------------------------------------------------
Problem(s) Fixed:

Initial release

Enhancements:

Limitations:

Dependencies:
ibm_fw_uefi_mle185a-1_85_anyos_i386_chg

IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.22.00 Build ID: IBM12200
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.22.00
- Update Utility release for IBM x86 servers.

Note: *- Only keep the legacy HDD/SSD in this Update program, the drives
were out of production by 4Q2014 or no firmware changes since 1Q2014.
No FW update for below legacy drives in this version.


This package acknowledges support and may include updates for
drives with product ID strings of:

Product ID FW

IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST3300557SS EA54
IBM-ESXSST3450757SS EA54
IBM-ESXSST3600957SS EA54
IBM-ESXSST31000424SS BC2D
IBM-ESXSST32000444SS BC2D
IBM-ESXSST9300603SS B53E
IBM-ESXSST9146803SS B53E
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9500430SS BD14
IBM-ESXSST3300657SS BA5A
IBM-ESXSST3450857SS BA5A
IBM-ESXSST3600057SS BA5A
IBM-ESXSST9146703SS E537
IBM-ESXSST9300503SS E537
IBM-ESXSST973352SS E626
IBM-ESXSST9146752SS E626
IBM-ESXSST9600204SS B54A
IBM-ESXSST9300605SS B55E
IBM-ESXSST9600205SS B55E
IBM-ESXSST9900805SS B55E
IBM-ESXSST9300505SS E558
IBM-ESXSST9600105SS E558
IBM-ESXSST9900705SS E558
IBM-ESXSST33000650SS BC3E
IBM-ESXSHUC106030CSS60 D3A6
IBM-ESXSHUC106060CSS60 D3A6
IBM-ESXSHUS723020ALS64 J3K8
IBM-ESXSHUS723030ALS64 J3K8
IBM-ESXSMBD2147RC SB1B
IBM-ESXSMBD2300RC SB1B
IBM-ESXSMBE2073RC SC18
IBM-ESXSMBE2147RC SC18
IBM-ESXSMBF2300RC SB2F
IBM-ESXSMBF2600RC SB2F
IBM-ESXSMK1401GRRB SC2E
IBM-ESXSMK3001GRRB SC2E
IBM-ESXSMK1401GRRR SF23
IBM-ESXSMK3001GRRR SF23
SG9XCS1F50GMIBM SA03SB6F
SG9XCS1B200GEIBM SA03SB6F
SG9XCS2D200GEIBM SA03SE6H
SG9XCS2D50GEIBM SA03SE6H
SG9XCS1F200GEIBM SA03SB6F
TX21B10200GE8IBM PRO6SP3E
TE22D10100GE8IBM PRO6SR3F
TX21B10400GE8IBM PRO6SP3E
WD2000F9YZ-23N2 WE31
WD3000F9YZ-23N2 WE31
WD4000F9YZ-23N2 WE31
WD2003FYYS-23T8B0 01.00D04
WD3000BLHX-23V7BV0 YA32
ST9160511NS BE1A
ST9500530NS BE1A
ST3500514NS BB2C
ST31000524NS BB2C
ST32000544NS BB2C
ST33000650NS BB3A
ST1000NM0011 BB4A
ST2000NM0011 BB4A
ST500NM0011 BB4A
HUA722010CLA330 JP4OA3PH
HUA722020ALA330 JKAOA3GA
HUA722050CLA330 JP2OA3PH
HDS721025CLA382 JP1OA54C
HUA723030ALA640 MKAOA930
HUA723020ALA640 MK7OA930
MTFDDAA512MAR-1K1AB MA57
MTFDDAK128MAR-1J1AA MA57
MTFDDAK256MAR-1K1AA MA57
MTFDDAK064MAR-1J1AA MA57
MTFDDAK512MAR-1K1AA MA57
MTFDDAA064MAR-1K1AB MA57
MTFDDAA128MAR-1K1AB MA57
MTFDDAA256MAR-1K1AB MA57
STECM8PSB2 2864
STECM8PSB2 SM08


**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.21.00 Build ID: IBM12100
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.21.00
- Update Utility release for IBM x86 servers.


This package acknowledges support and may include updates for
drives with product ID strings of:

SAS 3.5"

- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to BC5K

- ST2000NM0043, ST4000NM0043 to EC5H

- ST2000NM0034, ST4000NM0034, ST6000NM0034 to BC6E

- ST2000NM0054, ST4000NM0054, ST6000NM0054 to EC6E

- HUS724020ALS64, HUS724030ALS64, HUS724040ALS64 to MPXSJ3LA

- HUS724020ALS61, HUS724040ALS61 to MPXSN3LA

- VPCA300900EST1, VPCA450900EST, VPCA600900EST1 to VCXSA810



SAS 2.5"

- HUC156030CSS20, HUC156060CSS20 to KFXSJ2G8

- HUC101212CSS60 to CPXSJ2MC

- HUC101212CSS61 to CPXSN2MC

- HUC109030CSS60, HUC109060CSS60, HUC109090CSS60 to CEXSJ2EL

- HUC109030CSS61, HUC109060CSS61, HUC109090CSS61 to CEXSN2EL

- HUSMM1620ASS20, HUSMM1640ASS20, HUSMM1680ASS20, HUSMM1616ASS20
to SPXSJ4CC

- HUSMM1620ASS20E, HUSMM1640ASS20E, HUSMM1680ASS20E,
HUSMM1616ASS20E to SPXSN4CC

SATA 3.5"

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD40

- ST2000NM0024, ST4000NM0024, ST6000NM0024, ST5000NM0024 to BB67

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to BB5G


SATA 2.5"

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB to MB47

- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3 to EXT0CA35

- STECM8PSB2 to 2864/SM08


SATA 1.8"

- MTFDDAA120MBB, MTFDDAA240MBB, MTFDDAA480MBB, MTFDDAA800MBB to MB47




**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.20.00 Build ID: IBM12000
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.20.00
- Update Utility release for IBM x86 servers.

Note: *- Update the firmware on SAS/SATA SSDs to fix PSIRT issue with Intel SSD's.

This package acknowledges support and may include updates for
drives with product ID strings of:

SATA 2.5"


- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB480G4I, SSDSC2BB800G4I
to D201NE40.

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA39.

- SSDSC2BB080G4I, SSDSC2BB160G4I, SSDSC2BB300G4I, SSDSC2BB600G4I,
SSDSC2BB800G4I to D201NE40.

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC34.




SATA 1.8"

- SSDSC1NB080G4I, SSDSC1NB240G4I, SSDSC1NB400G4I to D201NE40.

- SSDSC1NA200G3I, SSDSC1NA400G3I to 5DV1NA39.

- SSDSC1NB800G4I to D201NE40.


**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.19.06 Build ID: IBM11906
**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.19.06
- Update Utility release for IBM x86 servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

- Remove TXA2D20200GA6I, TXA2D20400GA6I, TXA2D20800GA6I,
TXA2E21600GA6I from FW update utility for new code updating break Raid.








**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.18.03 Build ID: IBM11803

Critical Release
Reference RETAIN TIP: H214784 - MIGR-5098277
Reference RETAIN TIP: H214635 MIGR-5098037

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.18.03
- Update Utility release for IBM x86 servers.


Note: * - Fixed extremely low probable data compare error on I/O held
in standby when followed by power cycle; extremely low probable
data compare error due to nonvolatile cache(NVC) write data not
getting written to disc.
RETAIN TIP: H214784 - MIGR-5098277

Note: # - Fixed a block misalignment during a sequential read.

RETAIN TIP: H214635 MIGR-5098037


SAS 3.5"

- ST2000NM0034, ST4000NM0034, ST6000NM0034 to BC6B - similar
to Note * above.

- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to
BC5J - Enhance Dither Algorithm to prevent dwelling during
Idle environments.
- ST2000NM0043, ST4000NM0043 to EC5E - Enhance Dither Algorithm
to prevent dwelling during Idle environments.


SAS 2.5"

- TXA2E21600GA6I to GB7P - add support in profile.

- HUC156030CSS20, HUC156060CSS20 to J2G6 - add support in profile.


SATA 3.5"

- ST2000NM0024, ST4000NM0024, ST5000NM0024, ST6000NM0024 to
BB66 - similar to Note * above.

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to
BB5F - Enhance Dither Algorithm to prevent dwelling during
Idle environments.


SATA 2.5"


- MTFDDAA120MBB, MTFDDAA240MBB, MTFDDAA480MBB, MTFDDAA800MBB to
MB42 - add support in profile.

- SSDSC2BB080G4I, SSDSC2BB160G4I, SSDSC2BB300G4I, SSDSC2BB600G4I to
D201NB39 - add support in profile.



**************************************************************************

IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.17.01 Build ID: IBM11701

Critical Release
Reference RETAIN TIP: H214784 - MIGR-5098277
Reference RETAIN TIP: H214635 MIGR-5098037

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.17.01
- Update Utility release for IBM x86 servers.


Note: * - Fixed extremely low probable data compare error on I/O held
in standby when followed by power cycle; extremely low probable
data compare error due to nonvolatile cache(NVC) write data not
getting written to disc.
RETAIN TIP: H214784 - MIGR-5098277

Note: # - Fixed a block misalignment during a sequential read.
RETAIN TIP: H214635 MIGR-5098037


This package acknowledges support of qualified devices and
may include updates for drives with product ID strings of:


SAS 3.5"

- HUS724020ALS61, HUS724040ALS61 to N3L6 - internal updates.

- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to
BC5H - See Note * above.

- ST2000NM0054, ST4000NM0054, ST6000NM0054 to EC66 - see Note * above.

- ST2000NM0043, ST4000NM0043 to EC5D - See Note * above.

- Other drive codes are present for support identification.



SAS 2.5"

- WD3001BKHG-23D, WD6001BKHG-23D, WD9001BKHG-23D
to ZA34 - follow-on release.
- WD3002BKTG-23E, WD6002BKTG-23E, WD9002BKTG-23E
to ZC33 - follow-on release.

- HUC109030CSS60, HUC109060CSS60, HUC109090CSS60
to J2EH - follow-on release.

- TXA2D20200GA6I, STXA2D20400GA6I, TXA2D20800GA6I,
TXA2E21600GA6I to GB7P - enhancements.

- ST300MM0006, ST600MM0006, ST900MM0006 to B56T -
See Note * above.

- ST300MM0026, ST600MM0026, ST900MM0026 to E56E -
See Note * above.

- ST2000NM0043, ST4000NM0043 to EC5D - See Note * above.

- ST1200MM0007 to B57E - See Note * above.

- ST1200MM0017 to E577 - See Note * above.

- HUSMM1620ASS20, HUSMM1640ASS20, HUSMM1680ASS20, HUSMM1616ASS20 to
J4C8 - See Note # above
- HUSMM1620ASS20E, HUSMM1640ASS20E, HUSMM1680ASS20E, HUSMM1616ASS20E
to N4C8 - See Note # above

- Other drive codes are present for support identification.


SATA 3.5"

- MG04ACA200E, MG04ACA300E, MG04ACA400E, MG04ACA500E to SJ1D
- performance inhancements.

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to
BB5C - See Note * above.

- ST2000NM0024, ST4000NM0024, ST5000NM0024, ST6000NM0024 to
BB65 - See Note * above.

- WD2003FYYS-23W0B0 to WA36 - configuration additions.

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD39 -
configuration additions.

- HUA723030ALA6 to MKAOA930 - enhancements.
- HUA723020ALA6 to MK7OA930 - enhancements.

- Other drive codes are present for support identification.


SATA 2.5"


- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3 to
EXT0CA34 - ship level.

- Other drive codes are present for support identification.


SATA 1.8"

- Drive codes are present for support identification.



**************************************************************************

IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.16.05 Build ID: IBM11605

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.05
- Update Utility release for IBM x86 servers.

This package acknowledges support and may include updates for
drives with product ID strings of:


SAS 3.5"

- ESXSST1000NM0001, ESXSST2000NM0001 to BC4B - ensures that after
servicing an 03/11/00 error, an index for Parity Creations is calculated
correctly after a power cycle, that would otherwise make the
drive unresponsive.

- ESXSHUS724020ALS64, ESXSHUS724030ALS64, ESXSHUS724040ALS64
to J3L6 - Fixed unexpected 02/04/11 error; Fixed a drive logic self-initiated
reset on read/write long commands; Fixed a problem with large write sequential
transfers.

SAS 2.5"

- ESXSST9500620SS, ESXSST91000640SS to BD2K - ensures that after
servicing an 03/11/00 error, an index for Parity Creations is calculated
correctly after a power cycle, that would otherwise make the
drive unresponsive.

SATA 2.5"

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC32 - SCT WriteSame fix.



IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.16.04 Build ID: IBM11604

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.04
- Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

NOTE: Check notation under PCIe NVMe devices.

SATA 2.5"

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB to
MB42 -
> A drop in host power supply may cause bad block growth
> The bad block table may not properly increment
> Background activity may continue after STANDBY, STANDBY IMMEDIATE,
or SLEEP
> ID173/202 may show incorrect value when the NAND erase count exceeds 3000
> Changed DRAM timing
> Event log may be programmed when supply voltage from host is out of
specification

- SSDSC2BB012I4I, SSDSC2BB016T4I to G201NC32 - SCT WriteSame fix
that corrects a condition that may cause the drive to not respond.


PCIe NVMe 2.5"

- SSDPE2ME400G4I, SSDPE2ME800G4I, SSDPE2ME016G4I, SSDPE2ME020G4I
to 8DV1ND34 - will require two update runs and system reboots for device
fw update to complete--Please See the limitations in readme for details.

> Performance improvement on sub-4KB sequential write
> Fix drive reports higher than actual data units read and write
> Fix drive incorrectly counts unsafe power shutdown events on warm reboots


IBM Online SAS/SATA HDD/SSD Update Program.
Version 1.16.03 Build ID: SAS11603

**************************************************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.03
- Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

NOTE: Check notation under PCIe NVMe devices.

SAS 3.5"

- ESXSST2000NM0034, ESXSST4000NM0034, ESXSST6000NM0034 to BC67
- GA code.
- ESXSST2000NM0054, ESXSST4000NM0054, ESXSST6000NM0054 to EC66
- GA code.

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to XA39 - issues fixed:
slow performance with PI enabled;
drive hang on uncorrectable rd error in reallocation track;
PERSISTANT RESERVATION command not working correctly;
reliability improvements around off-track write protection.


SAS 2.5"

- ESXSTXA2D20200GA6, ESXSTXA2D20400GA6, ESXSTXA2D20800GA6,
ESXSTXA2E21600GA6 to GB7P - fixes implemented to support PI
issues.

- ESXSST300MP0005 to B675 - GA code.
- ESXSST300MP0025 to E671 - GA code.

- ESXSST300MP0035, ESXSST600MP0035 to B683 - GA code.
- ESXSST300MP0045, ESXSST300MP0045 to E685 - GA code.

- ESXSST300MX0012, ESXSST600MX0052 to BH53 - GA code.

- ESXSWD3001BKHG-23D, ESXSWD6001BKHG-23D, ESXSWD9001BKHG-23DS
to ZA34 - issues fixed:
slow performance with PI enabled;
drive hang on uncorrectable rd error in reallocation track;
PERSISTANT RESERVATION command not working correctly;
drive was reporting 0B/11 instead of 03/11.
- ESXSWD3002BKTG-23E, ESXSWD6002BKTG-23E, ESXSWD9002BKTG-23E
to ZC33 - issues fixed:
slow performance with PI enabled;
drive hang on uncorrectable rd error in reallocation track;
PERSISTANT RESERVATION command not working correctly;
reliability improvements around off-track write protection.


SATA 3.5"

- MG04ACA200E, MG04ACA300E, MG04ACA400E, MG04ACA500E to SJ1C - GA code


SATA 2.5"


- ST9250610NS, ST9500620NS, ST91000640NS to BE2B - Update configuration change.

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB to
MB34 -
> Some Out of Range LBAs accepted by NCQ commands where
they should be aborted.
> SataDownShift.srt failed, Smart attribute Raw lost with
perform dirty pwr cycle .
> Low Power Entry Bug Identified from Marvell Code Review
> Track Timeout, Marvel 373 sequencer issue
> Unreasonable ECC count in SMART ID 195


- SSDSC2BB080G4I, SSDSC2BB160G4I, SSDSC2BB300G4I, SSDSC2BB600G4I to
D201NB39 - SCT WriteSame Disable.

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA38 -
CDC Fix for 15GB default values (should abort); SCT WriteSame
Disable.

- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB480G4I, SSDSC2BB800G4I to
D201NB39/D201NE39 - SCT WriteSame Disable.


**************************************************************************
IBM Online SAS/SATA HDD/SSD Update Program for Linux.
Version 1.16.00 Build ID: SAS11600

*******************************************
IBM SAS/SATA HDD/SSD Update Program
Version 1.16.00
- First Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:

NOTE: Check notation under PCIe NVMe devices.

SAS 3.5"

- ESXSST1000NM0023, ESXSST2000NM0023, ESXSST3000NM0023,
ESXSST4000NM0023 to BC5E

- ESXSST2000NM0043, ESXSST3000NM0043, ESXSST4000NM0043,
ESXSST1000NM0043 to EC5A

- ESXSST3300557SS, ESXSST3450757SS, ESXSST3600957SS to EA54

- ESXSST3300657SS, ESXSST3450857SS, ESXSST3600057SS to BA5A

- ESXSST33000650SS to BC3E

- ESXSST1000NM0001, ESXSST2000NM0001 to BC4A

- ESXSHUS724020ALS64, ESXSHUS724030ALS64, ESXSHUS724040ALS64
to J3L5

- ESXSHUS724020ALS61, ESXSHUS724040ALS61 to N3L5

- ESXSHUS723020ALS64, ESXSHUS723030ALS64 to J3K8

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to XA38



SAS 2.5"

- ESXSTXA2D20200GA6I, ESXSTXA2D20400GA6I, ESXSTXA2D20800GA6I,
ESXSTXA2E21600GA6I to GB7H

- ESXSST300MM0006, ESXSST600MM0006, ESXSST900MM0006 to B56M;
- ESXSST300MM0026, ESXSST600MM0026, ESXSST900MM0026 to E56D

- ESXST1200MM0007 to B57B
- ESXST1200MM0017 to E576

- ESXSST9300605SS, ESXSST9600205SS, ESXSST9900805SS to B55E
- ESXSST9300505SS, ESXSST9600105SS, ESXSST9900705SS to E558

- ESXSST9146853SS, ESXSST9300653SS to B63K

- ESXSST9146753SS, ESXSST9300553SS to E638
- ESXSST9500620SS, ESXSST91000640SS to BD2J

- ESXSHUC101212CSS60 to J2MA
- ESXSHUC101212CSS61 to N2M9

- ESXSHUC156030CS420, ESXSHUC156060CS420 to J5G2
- ESXSHUC156030CSS20, ESXSHUC156060CSS20 to J2G4

- ESXSHUC156030CS420E, ESXSHUC156060CS420E to N5G2

- ESXSHUC156030CSS20E, ESXSHUC156060CSS20E to N2G4

- ESXSHUC101860CS420, ESXSHUC101890CS420, ESXSHUC101812CS420,
ESXSHUC101818CS420 to J5H2
- ESXSHUC101860CS420E, ESXSHUC101890CS420E, ESXSHUC101812CS420E,
ESXSHUC101818CS420E to N5H2

- ESXSHUC109030CSS60, ESXSHUC109060CSS60, ESXSHUC109090CSS60
to J2EG
- ESXSHUC109030CSS61E, ESXSHUC109060CSS61E, ESXSHUC109090CSS61E
to N2EG

- ESXSAL13SXB300N, ESXSAL13SXB600N to SC36

- ESXSMBF2300RC, ESXSMBF2600RC to SB2F

- ESXSMK1401GRRB, ESXSMK3001GRRB to SC2E
- ESXSMK1401GRRR, ESXSMK3001GRRR to SF23
- ESXSMK3001GRDB, ESXSMK6001GRDB, ESXSMK9001GRDB to SB35

- ESXSWD3001BKHG-23D, ESXSWD6001BKHG-23D, ESXSWD9001BKHG-23D
to ZA33
- ESXSWD3002BKTG-23E, ESXSWD6002BKTG-23E, ESXSWD9002BKTG-23E
to ZC32

- EXSXHUSMM1620ASS20, EXSXHUSMM1640ASS20, EXSXHUSMM1680ASS20,
EXSXHUSMM1616ASS20 to J4C6
- EXSXHUSMM1620ASS20E, EXSXHUSMM1640ASS20E, EXSXHUSMM1680ASS20E,
EXSXHUSMM1616ASS20E to N4C6



SATA 3.5"

- WD1003FBYX-23Y7B0, WD2003FYYS-23W0B0 to WA35

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD37 -
Resolves drive initiated reset (DBS (Debug Stop event))
encountered under a narrow timing window (~1ns) for specific
command/access patterns, due to the drive’s handling of
command automation where it was possible for an internal
hardware resource conflict to occur between two tasks.

- ST33000650NS to BB3A

- ST1000NM0011, ST2000NM0011 to BB4A

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033
to BB5A

- HUA723020ALA640 to MK7OA930
- HUA723030ALA640 to MKAOA930



SATA 2.5"

- ST9250610NS, ST9500620NS, ST91000640NSto BE2A

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB
to MB33

- SSDSC2BB080G4I, SSDSC2BB120G4I, SSDSC2BB160G4I, SSDSC2BB240G4I,
SSDSC2BB300G4I, SSDSC2BB480G4I, SSDSC2BB600G4I, SSDSC2BB800G4I
to D201NB38

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC31

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA37

- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3
to EXST0CA34


PCIe NVMe 2.5"

- SSDPE2ME400G4I, SSDPE2ME800G4I, SSDPE2ME016G4I, SSDPE2ME020G4I
to 8DV1ND32 - will require a system reboot for device fw
update to complete.


*********************************************************************
SAS/SATA HDD/SSD Update Program
Version 1.15.00
- First Update Utility release for IBM System x servers.

This package acknowledges support and may include updates for
drives with product ID strings of:



SAS 3.5"

- ESXSST1000NM0023, ESXSST2000NM0023, ESXSST3000NM0023,
ESXSST4000NM0023 to BC5E

- ESXSST2000NM0043, ESXSST3000NM0043, ESXSST4000NM0043,
ESXSST1000NM0043 to EC5A

- ESXSST3300557SS, ESXSST3450757SS, ESXSST3600957SS to EA54

- ESXSST3300657SS, ESXSST3450857SS, ESXSST3600057SS to BA5A

- ESXSST33000650SS to BC3E

- ESXSST1000NM0001, ESXSST2000NM0001 to BC4A

- ESXSHUS724020ALS64, ESXSHUS724030ALS64, ESXSHUS724040ALS64
to J3L5

- ESXSHUS724020ALS61, ESXSHUS724040ALS61 to N3L5

- ESXSHUS723020ALS64, ESXSHUS723030ALS64 to J3K8

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to

- ESXSWD1001FYYG-23S, ESXSWD2001FYYG-23S, ESXSWD3001FYYG-23S,
ESXSWD4001FYYG-23S to XA38



SAS 2.5"

- ESXSTXA2D20200GA6I, ESXSTXA2D20400GA6I, ESXSTXA2D20800GA6I,
ESXSTXA2E21600GA6I to GB7H

- ESXSST300MM0006, ESXSST600MM0006, ESXSST900MM0006 to B56M;
- ESXSST300MM0026, ESXSST600MM0026, ESXSST900MM0026 to E56D

- ESXST1200MM0007 to B57B
- ESXST1200MM0017 to E576

- ESXSST9300605SS, ESXSST9600205SS, ESXSST9900805SS to B55E
- ESXSST9300505SS, ESXSST9600105SS, ESXSST9900705SS to E558

- ESXSST9146853SS, ESXSST9300653SS to B63K

- ESXSST9146753SS, ESXSST9300553SS to E638
- ESXSST9500620SS, ESXSST91000640SS to BD2J

- ESXSHUC101212CSS60 to J2MA
- ESXSHUC101212CSS61 to N2M9

- ESXSHUC156030CS420, ESXSHUC156060CS420 to J5G2
- ESXSHUC156030CSS20, ESXSHUC156060CSS20 to J2G4

- ESXSHUC156030CS420E, ESXSHUC156060CS420E to N5G2

- ESXSHUC156030CSS20E, ESXSHUC156060CSS20E to N2G4

- ESXSHUC101860CS420, ESXSHUC101890CS420, ESXSHUC101812CS420,
ESXSHUC101818CS420 to J5H2
- ESXSHUC101860CS420E, ESXSHUC101890CS420E, ESXSHUC101812CS420E,
ESXSHUC101818CS420E to N5H2

- ESXSHUC109030CSS60, ESXSHUC109060CSS60, ESXSHUC109090CSS60
to J2EG
- ESXSHUC109030CSS61E, ESXSHUC109060CSS61E, ESXSHUC109090CSS61E
to N2EG

- ESXSAL13SXB300N, ESXSAL13SXB600N to SC36

- ESXSMBF2300RC, ESXSMBF2600RC to SB2F

- ESXSMK1401GRRB, ESXSMK3001GRRB to SC2E
- ESXSMK1401GRRR, ESXSMK3001GRRR to SF23
- ESXSMK3001GRDB, ESXSMK6001GRDB, ESXSMK9001GRDB to SB35

- ESXSWD3001BKHG-23D, ESXSWD6001BKHG-23D, ESXSWD9001BKHG-23D
to ZA33
- ESXSWD3002BKTG-23E, ESXSWD6002BKTG-23E, ESXSWD9002BKTG-23E
to ZC32

- EXSXHUSMM1620ASS20, EXSXHUSMM1640ASS20, EXSXHUSMM1680ASS20,
EXSXHUSMM1616ASS20 to J4C6
- EXSXHUSMM1620ASS20E, EXSXHUSMM1640ASS20E, EXSXHUSMM1680ASS20E,
EXSXHUSMM1616ASS20E to N4C6



SATA 3.5"

- WD1003FBYX-23Y7B0, WD2003FYYS-23W0B0 to WA35

- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD37

- ST9500620NS, ST91000640NS to BE2A

- ST33000650NS to BB3A

- ST1000NM0011, ST2000NM0011 to BB4A

- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033
to BB5A

- HUA723020ALA640 to MK7OA930
- HUA723030ALA640 to MKAOA930



SATA 2.5"

- ST9500620NS, ST91000640NS

- MTFDDAK120MBB, MTFDDAK240MBB, MTFDDAK480MBB, MTFDDAK800MBB
to MB33

- SSDSC2BB080G4I, SSDSC2BB120G4I, SSDSC2BB160G4I, SSDSC2BB240G4I,
SSDSC2BB300G4I, SSDSC2BB480G4I, SSDSC2BB600G4I, SSDSC2BB800G4I
to D201NB37

- SSDSC2BB012T4I, SSDSC2BB016T4I to G201NC31

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to 5DV1NA36

- MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3
to EXST0CA34

NOTE TO SERVICE - Reference RETAIN TIP H29851
*******************************************
SAS Hard Disk Drive Update Program
Version 1.14.04
Critical Release
Reference RETAIN TIP H29851

This package includes updates to drives with product ID strings of:

SAS 2.5"

Initial code Release
- SMK3001GRDB, SMK6001GRDB, SMK9001GRDB to SB35


SATA 2.5"

- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to NA36
- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB400G4I, SSDSC2BB800G4I
to NB37 - fix to prevent possible drive lock up during format.


SATA 1.8"

Initial Code Release
- SSDSC1NA200G3I, SSDSC1NA400G3I to NA36
- SSDSC1NB080G4I, SSDSC1NB240G4I, SSDSC1NB400G4I to NB37
- fix to prevent possible drive lock up during format.

===================================================================
IBM Online SAS/SATA Hard Disk Drive Update Program
Version 1.14.03-2 Build ID: SAS11403-2

NOTE TO SERVICE - Reference RETAIN TIPS H211424 & H211667
*******************************************
IBM SAS Hard Disk Drive Update Program
Version 1.14.03-2
Critical Release
Reference RETAIN TIP H211424 & H211667

This package includes updates to drives with product ID strings of:


SAS 3.5"

Initial Code Releases
- ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to BC5B
- ST2000NM0043, ST4000NM0043 to EC59
- WD1001FYYG-23S, WD2001FYYG-23S, WD3001FYYG-23S,
WD4001FYYG-23S to XA35

Other
- ST1000NM0001, ST2000NM0001 to BC4A - support persistent reservation
- HUS723020ALS64, HUS723030ALS64 to J3K8 - servo adjustments


SAS 2.5"

Initial Code Releases
- ST300MM0006, ST600MM0006, ST900MM0006 to B56H
- ST300MM0026, ST600MM0026, ST900MM0026 to E568
- TXA2D20200GA6I, TXA2D20400GA6I, TXA2D20800GA6I, TXA2D21600GA6I
to GB76 - see Retain Tip H211424.
- HUC101212CSS60 to J2M7
- HUC101212CSS61 to N2M7
- T1200MM0007 to B576
- T1200MM0017 to E574
- ST600MX0001 to BH13
- WD3002BKTG-23E, WD6002BKTG-23E, WD9002BKTG-23E to ZC31
- ST9500431SS to ED12
- ST9146703SS to E536
- ST973352SS to E625
- ST9300553SS to E636
- HUC109030CSS61E, HUC109060CSS61E, HUC109090CSS61E to N2EF
- MK3001GRDB, MK6001GRDB, MK9001GRDB to SB35 - drive Que depth fix;
see Retain Tip H211667.
- HUC109030CSS60, HUC109060CSS60, HUC109090CSS60 to J2EF
- HUC109030CSS61E, HUC109060CSS61E, HUC109090CSS61E to N2EF

Other
- WD3001BKHG-23D, WD6001BKHG-23D, WD9001BKHG-23D to ZA32 -
performance, non-critical fixes and robustness changes.

- ST9600204SS to B54A with maintainance fixes and performance
improvements.

- MBD2147RC, MBD2300RC to SB1B - drive Que depth fix;
- MBE2073RC, MBE2147RC to SC18 - drive Que depth fix;
- MBF2300RC, MBF2600RC to SB2F - drive Que depth fix;
- MK1401GRRB, MK3001GRRB to SC2E - drive Que depth fix;
see Retain Tip H211667.

- ST9500620SS, ST91000620SS to BD2F - support persistent reservation
and maintainance fixes.


SATA 3.5"

Initial Code Release
- WD801ABYS-23C0A0, WD1601ABYS-23C0A0 to 06.06H05
- WD5003ABYX-23 to WC38 - added mfg. parameters.
- WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD36
- ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to BB58

Other


SATA 2.5"

Initial Code Release
- SG9XCS2D50GEIBM to SE6H
- WD3000BLHX-23V7BV to YA31
- SSDSC2BA200G3I, SSDSC2BA400G3I, SSDSC2BA800G3I to NA34
- SSDSC2BB120G4I, SSDSC2BB240G4I, SSDSC2BB400G4I, SSDSC2BB800G4I
to NB34

Other
- ST9250610NS, ST9500620NS, ST91000640NS to BE29 - maintainance
updates.
- MTFDDAK064MAR-1J1AA, MTFDDAK128MAR-1J1AA, MTFDDAK256MAR-1K1AA,
MTFDDAK512MAR-1K1AA to MA57 - added mfg. parameters.


SATA 1.8"

Initial Code Release
- SSDSC1NA200G3I, SSDSC1NA400G3I to NA34
- SSDSC1NB080G4I, SSDSC1NB240G4I, SSDSC1NB400G4I to NB34

Other
- MTFDDAA064MAR-1J1AB, MTFDDAA128MAR-1J1AB, MTFDDAA256MAR-1K1AB,
MTFDDAA512MAR-1K1AB to MA57 - added mfg. parameters.

===================================================================
Version 1.13.01 Build ID: SAS_113

NOTE TO SERVICE - Reference RETAIN H207993

*******************************************
IBM SAS Hard Disk Drive Update Program
Version 1.13.01
Critical Release
Reference RETAIN H207993

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- HUS723020ALS64 to J3K7 Additions to VPD information used by
manufacturing and fixes for overall robustness.

- HUS723030ALS64 to J3K7 Initial Code Release

- ST31000424SS, ST32000444SS to BC2D
- ST1000NM0001, ST2000NM0001 to BC49
Fixes for overall robustness.

- ST33000650SS to BC3E Initial Code Release


SAS 2.5"

- MK1401GRRB, MK3001GRRB to SC29
Fixes for overall robustness.

- MBF2300RC, MBF2600RC to SB2C
Initial Code Release.

- ST9300605SS, ST9600205SS, ST9900805SS to B55D
ST9146853SS, ST9300653SS to B63B
ST9500620SS, ST91000640SS to BD2E
ST9300505SS, ST9600105SS, ST9900705SS to E557
ST9146753SS to E636
Additions to VPD information used by manufacturing and
fixes for overall robustness.

SATA 3.5"

- ST500NM0011, ST2000NM0011, ST1000NM0011 to BB4A
ST3500514NS, ST31000524NS, ST32000644NS to BB2C
Reliability improvements, Additions to VPD information
used by manufacturing

- ST33000650NS to BB3A Initial Code Release

- WD5003ABYX-23 to WC36, WD1003FBYX-23Y7B0 to WB35,
WD2003FYYS-23W0B0 to WA35
Reliability improvements, Additions to VPD information
used by manufacturing

- HUA723020ALA640 to MK7OA910
Additions to VPD information used by manufacturing.

- HUA723030ALA640 to MKAOA910 Initial Code Release

- HUA722050CLA330, HUA722010CLA330 to A3PH
Initial Code Release

SATA 2.5"

- TE22D10100GE8IBM to SR3B Initial Code Release

- MTFDDAK064MAR-1J1AA, MTFDDAK128MAR-1J1AA,
MTFDDAK256MAR-1K1AA, MTFDDAK512MAR-1K1AA
to MA55 Initial Code Release

- ST9250610NS, ST9500620NS, ST91000640NS to BE28
Fixes for overall robustness.

SATA 1.8"

- MTFDDAA064MAR-1J1AB, MTFDDAA128MAR-1J1AB,
MTFDDAA256MAR-1K1AB, MTFDDAA512MAR-1K1AB
to MA55 Initial Code Release

- TX21B10100GE8IBM, TX21B10200GE8IBM, TX21B10400GE8IBM
to SP3A Initial Code Release

===============================================================

Version 1.12.01
Critical Release
Reference RETAIN #H207740

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- VPCA300900EST1, VPCA450900EST1, VPCA600900EST1 to A3C4,
Corrects firmware bug that may cause data corruption.
For further information, please refer to Retain Tip H207740.

===============================================================

Version 1.12
(Critical)

Added Support for SAS Controllers M5115 and H1135

SAS 3.5"
Product ID FW

IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4D
IBM-ESXSST3300656SS BA4D
IBM-ESXSST3450856SS BA4D
IBM-ESXSST3300657SS BA5A
IBM-ESXSST3450857SS BA5A
IBM-ESXSST3600057SS BA5A
IBM-ESXSST3750630SS BC1I
IBM-ESXSST31000640SS BC1I
IBM-ESXSST31000424SS BC2C
IBM-ESXSST32000444SS BC2C
IBM-ESXSST33000650SS BC3D
IBM-ESXSST1000NM0001 BC48
IBM-ESXSST2000NM0001 BC48
IBM-ESXSVPCA300900EST1 A3C2
IBM-ESXSVPCA600900EST1 A3C2
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSHUS723020ALS64 J26C
IBM-ESXSHUS723030ALS64 J26C
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5"
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST973402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53E
IBM-ESXSST9146803SS B53E
IBM-ESXSST9600204SS B549
IBM-ESXSST9300605SS B55C
IBM-ESXSST9600205SS B55C
IBM-ESXSST9900805SS B55C
IBM-ESXSST936751SS B617
IBM-ESXSST973451SS B617
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9146853SS B63A
IBM-ESXSST9300653SS B63A
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD2C
IBM-ESXSST91000640SS BD2C
IBM-ESXSST9300503SS E536
IBM-ESXSST9300505SS E555
IBM-ESXSST9600105SS E555
IBM-ESXSST9900705SS E555
IBM-ESXSST9146752SS E625
IBM-ESXSST9146753SS E635
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D3A6
IBM-ESXSHUC106060CSS60 D3A6
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBF2300RC SB2B
IBM-ESXSMBF2600RC SB2B
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMK1401GRRB SC27
IBM-ESXSMK3001GRRB SC27
IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107
IBM-ESXSWD9001BKHG-23D ZA31
IBM-ESXSWD6001BKHG-23D ZA31
IBM-ESXSWD3001BKHG-23D ZA31

SATA 3.5"
Product ID FW

WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WD1602ABYS-23B7A0 02.03B07
WD2502ABYS-23B7A0 02.03B08
WD2003FYYS-23W0B0 WA34
WDC WD1003FBYX-23Y7B0 WB33
WD5003ABYX-23 WC34
ST380819AS 3.05
ST3160828AS 3.05
ST340212AS 3.05
ST3160023AS 3.48
ST380013AS 3.48
ST340014AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB15
ST3500320NS BB15
ST3750330NS BB15
ST31000340NS BB15
ST3500514NS BB2A
ST31000524NS BB2A
ST32000644NS BB2A
ST33000650NS BB38
ST1000NM0011 BB47
ST2000NM0011 BB47
ST500NM0011 BB47
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3IA
HDS721025CLA382 JP1OA54C
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
HUA723020ALA640 MK7OA900
HUA723030ALA640 MKAOA900
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE1A
ST9500530NS BE1A
ST9250610NS BE25
ST9500620NS BE25
ST91000640NS BE25

SSD
Product ID FW

TX21B10200GE1IBM PRO6SP36
TX21B10400GE1IBM PRO6SP36
TX21B10100GE8IBM PRO6SP36
TE22D10100GE8IBM PRO6SR36
SG9XCS1B50GMIBM SA03SB6F
SG9XCS1F200GEIBM SA03SB6F
SG9XCS2D200GEIBM SA03SE6H
GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
MTFDDAA512MAR-1K1AB MA52
MTFDDAK128MAR-1J1AA MA52
MTFDDAK256MAR-1K1AA MA52
MTFDDAK064MAR-1J1AA MA52
MTFDDAK512MAR-1K1AA MA52
MTFDDAA064MAR-1K1AB MA52
MTFDDAA128MAR-1K1AB MA52
MTFDDAA256MAR-1K1AB MA52
STEC M8PSB1 0409
STEC MACH8 IOPS 2804
STEC M8PSB2 T4 SM06
STEC M8PSB1 T4 SM16

SAS 3.5"

- ST3300657SS, ST3450857SS, ST3600057SS to BA5A
VPCA300900EST1, VPCA600900EST1 to A3C2
Additions to VPD information used by manufacturing

- ST3750630SS, ST31000640SS to BC1I
ST31000424SS, ST32000444SS to BC2C
Mode Page change to address performance issues under certain system configurations

- ST33000650SS to BC3D
ST1000NM0001, ST2000NM0001 to BC48
Protection Information Fix - see Retain Tip H206140

- HUS723020ALS64, HUS723030ALS64 to J26C
Initial Code Release

SAS 2.5"

- ST9300603SS, ST9146803SS to B53E
ST9600204SS to B549
Additions to VPD information used by manufacturing

- ST9300605SS, ST9600205SS, ST9900805SS to B55C
ST9146853SS, ST9300653SS to B63A
ST9500620SS, ST91000640SS to BD2C
ST9300505SS to E555
ST9146753SS to E635
Protection Information Fix - see Retain Tip H206140

- ST9600105SS, ST9900705SS to E555
Inital Code Release

- HUC106030CSS60, HUC106060CSS60 to D3A6
Performance improvements, critical fixes for Protection Information (PI)
operation - see Retain Tip H206140

- MK1401GRRB, MK3001GRRB to SC27
Additions to VPD information used by manufacturing

- WD9001BKHG-23D, WD6001BKHG-23D, WD3001BKHG-23D to ZA31
Initial Code Release

SATA 3.5"

- WD2502ABYS-23B7A0 to 02.03B08
WD1602ABYS-23B7A0 to 02.03B07
Critical fix to address premature drive failures.

- ST3500514NS, ST31000524NS, ST32000644NS to BB2A
ST33000650NS to BB38
ST1000NM0011, ST2000NM0011, ST500NM0011 to BB47
Fixes a potential, but rare data corruption issue which requires
a background reallocation that exceeds the error recovery timer.

- HUA723020ALA640 to MK70A900
HUA723030ALA640 to MKA0A900
Initial Code Release

SATA 2.5"

- ST9160511NS, ST9500530NS to BE1A
- ST9250610NS, ST9500620NS, ST91000640NS to BE25
Fixes a potential, but rare data corruption issue which requires
a background reallocation that exceeds the error recovery timer.

SSD

- TX21B10200GE1IBM, TX21B10400GE1IBM, TX21B10100GE8IBM to PRO6SP36
TE22D10100GE8IBM to PRO6SR36
Initial Code Release

- MTFDDAK128MAR-1J1AA, MTFDDAK256MAR-1K1AA to MA52
Initial Code Release

- MTFDDAA512MAR-1K1AB, MTFDDAK064MAR-1J1AA, MTFDDAK512MAR-1K1AA,
MTFDDAA064MAR-1K1AB, MTFDDAA128MAR-1K1AB, MTFDDAA256MAR-1K1AB to MA52
Fixes SMART attribute 190 (Current Temp) which caused warning messages
with some versions of Linux

- STEC MACH8 IOPS to 2804
STEC M8PSB2 T4 to SM06
Additions to VPD information used by manufacturing
Fixes potential drive failure if power loss occurs during firmware update.

*******************************************

Version 1.11
(Critical)

SAS 3.5"
Product ID FW

IBM-ESXSVPCA300900EST1 A3C0
IBM-ESXSVPCA600900EST1 A3C0
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4D
IBM-ESXSST3300656SS BA4D
IBM-ESXSST3450856SS BA4D
IBM-ESXSST3300657SS BA59
IBM-ESXSST3450857SS BA59
IBM-ESXSST3600057SS BA59
IBM-ESXSST3750630SS BC1H
IBM-ESXSST31000640SS BC1H
IBM-ESXSST31000424SS BC2B
IBM-ESXSST32000444SS BC2B
IBM-ESXSST33000650SS BC3A
IBM-ESXSST1000NM0001 BC44
IBM-ESXSST2000NM0001 BC44
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5"
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSSTLFF_SATA3401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSSTLFF_SATA3401SS B51D
IBM-ESXSSTLFF_SATA3402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53C
IBM-ESXSST9146803SS B53C
IBM-ESXSST9600204SS B548
IBM-ESXSST9300605SS B559
IBM-ESXSST9600205SS B559
IBM-ESXSST9900805SS B559
IBM-ESXSST936751SS B617
IBM-ESXSSTLFF_SATA3451SS B617
IBM-ESXSSTLFF_SATA3452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9146853SS B637
IBM-ESXSST9300653SS B637
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD29
IBM-ESXSST91000640SS BD29
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D390
IBM-ESXSHUC106060CSS60 D390
IBM-ESXSST9300503SS E536
IBM-ESXSST9300505SS E553
IBM-ESXSST9146752SS E625
IBM-ESXSST9146753SS E633
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBF2300RC SB28
IBM-ESXSMBF2600RC SB28
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMK1401GRRB SC23
IBM-ESXSMK3001GRRB SC23
IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107

SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB15
ST3500320NS BB15
ST3750330NS BB15
ST31000340NS BB15
ST3500514NS BB29
ST31000524NS BB29
ST32000644NS BB29
ST33000650NS BB36
ST1000NM0011 BB46
ST2000NM0011 BB46
ST500NM0011 BB46
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HDS721025CLA382 JP1OA3GE
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31
WD5003ABYX-23 WC31
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WDC WD2502ABYS-23B7A0 02.03B06
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE19
ST9500530NS BE19
ST9250610NS BE24
ST9500620NS BE24
ST91000640NS BE24

SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2765
STEC M8PSB2 T4 SM05
SG9XCS2D200GEIBM SA03SE6C
MTFDDAK128MAR-1JAAB MA44
MTFDDAK256MAR-1JAAB MA44

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0409
STEC M8PSB1 T4 SM16
SG9XCS1B50GMIBM SA03SB6C
SG9XCS1F200GEIBM SA03SB6C


SAS 3.5"

- ST33000650SS to BC3A
ST1000NM0001, ST2000NM0001 to BC44
Additions and corrections to VPD information used by manufacturing

SAS 2.5"

- ST9300605SS, ST9600205SS, ST9900805SS to B559
ST9146853SS, ST9300653SS to B637
ST9500620SS, ST91000640SS to BD29
ST9300505SS to E553
SST9146753SS to E633
HUC106030CSS60, HUC106060CSS60 to D390
Additions and corrections to VPD information used by manufacturing

- MK1401GRRB, MK3001GRRB to SC23
Fixes a pottential data corruption bug if there is an
unexpected power loss.

SATA 3.5"

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB15
ST3500514NS, ST31000524NS, ST32000644NS to BB29
ST33000650NS to BB36
ST1000NM0011, ST2000NM0011, ST500NM0011 to BB46

SATA SSD

- SG9XCS1B50GMIBM, SG9XCS1F200GEIBM to SA03SB6C
SG9XCS2D200GEIBM to SA03SE6C
Fix for potential hang during an unexpected power cycle

MTFDDAK128MAR-1JAAB, MTFDDAK256MAR-1JAAB to MA44
Initial Release

===========================================

Version 1.10
(Critical)

SAS 3.5"
Product ID FW

IBM-ESXSVPCA300900EST1 A3C0
IBM-ESXSVPCA600900EST1 A3C0
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4C
IBM-ESXSST3300656SS BA4C
IBM-ESXSST3450856SS BA4C
IBM-ESXSST3300657SS BA58
IBM-ESXSST3450857SS BA58
IBM-ESXSST3600057SS BA58
IBM-ESXSST3750630SS BC1H
IBM-ESXSST31000640SS BC1H
IBM-ESXSST31000424SS BC2B
IBM-ESXSST32000444SS BC2B
IBM-ESXSST33000650SS BC37
IBM-ESXSST1000NM0001 BC42
IBM-ESXSST2000NM0001 BC42
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5" (SFF)
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST973402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53C
IBM-ESXSST9146803SS B53C
IBM-ESXSST9600204SS B548
IBM-ESXSST9300605SS B556
IBM-ESXSST9600205SS B556
IBM-ESXSST9900805SS B556
IBM-ESXSST936751SS B617
IBM-ESXSST973451SS B617
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9146853SS B635
IBM-ESXSST9300653SS B635
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD26
IBM-ESXSST91000640SS BD26
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D340
IBM-ESXSHUC106060CSS60 D340
IBM-ESXSST9300503SS E536
IBM-ESXSST9300505SS E552
IBM-ESXSST9146752SS E625
IBM-ESXSST9146753SS E632
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBF2300RC SB28
IBM-ESXSMBF2600RC SB28
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107

SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB15
ST3500320NS BB15
ST3750330NS BB15
ST31000340NS BB15
ST3500514NS BB29
ST31000524NS BB29
ST32000644NS BB29
ST33000650NS BB34
ST1000NM0011 BB45
ST2000NM0011 BB45
ST500NM0011 BB45
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HDS721025CLA382 JP1OA3GE
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31
WD5003ABYX-23 WC31
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WDC WD2502ABYS-23B7A0 02.03B06
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE19
ST9500530NS BE19
ST9250610NS BE24
ST9500620NS BE24
ST91000640NS BE24

SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2765
STEC M8PSB2 T4 SM05
SG9XCS2D200GEIBM SA03SE6C

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0409
STEC M8PSB1 T4 SM16
SG9XCS1B50GMIBM SA03SB6C
SG9XCS1F200GEIBM SA03SB6C

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- VPCA300900EST1, VPCA600900EST1 to A3C0
Correction to VPD information used by manufacturing

- ST31000424SS, ST32000444SS to BC2B
Fixes to improve robustness from certain read errors due to encroachment

- ST33000650SS to BC37
Fixes to improve overall robustness.

- ST1000NM0001, ST2000NM0001 to BC42
Inital Release

SAS 2.5" (SFF)

- ST9300605SS, ST9600205SS, ST9900805SS to B556
- ST9146853SS, ST9300653SS to B635
Fixes to improve overall robustness.

ST9300505SS to E552
ST9146753SS to E632
Initial Release

- ST9500620SS, ST91000640SS to BD26
Improve general robustness and added support for DPICZ

- HUC106030CSS60, HUC106060CSS60 to D340
Improve general robustness

- MBF2300RC, MBF2600RC to SB28
Improves performance in certain benchmarks

SATA 3.5"

- ST33000650NS to BB34
Fixes to improve overall robustness.

- ST1000NM0011, ST2000NM0011, ST500NM0011 to BB45
Initial Release

- ST3500514NS, ST31000524NS, ST32000644NS to BB29
Fixes for intermittent drive hangs

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB15
Added enhancement for improved robustness


SATA 2.5"

- ST9250610NS, ST9500620NS, ST91000640NS to BE24
Initial Release

- ST9160511NS, ST9500530NS to BE19
Fixes for overall robustness.


SATA 2.5" SSD

- STEC MACH8 IOPS to 2765
STEC M8PSB2 T4 to SM05
Fixes potential drive lock up during cold or warm boots
Fixes issues with RHEL 6.x installation

- SG9XCS2D200GEIBM to SA03SE6C
Fixes default drive VPD information for manufacturing,
the default LED behavior on certain systems and
fixes issues with client install thru VMWare 5.x

SATA 1.8" SSD

- STEC M8PSB1 to 0409
STEC M8PSB1 T4 to SM16
Fixes potential drive lock up during cold or warm boots
Fixes issues with RHEL 6.x installation

- SG9XCS1B50GMIBM to SA03SB6C
SASG9XCS1F200GEIBM to SA03SB6C
Fixes potential drive lock up during cold or warm boots and
the default LED behavior on certain systems and
fixes issues with client install thru VMWare 5.x

===========================================

Version 1.09
(Critical)

SAS 3.5"
Product ID FW

IBM-ESXSVPCA300900EST1 A3B8
IBM-ESXSVPCA450900EST1 A3B8
IBM-ESXSVPCA600900EST1 A3B8
IBM-ESXSVPBA073C3ETS11 A496
IBM-ESXSVPBA146C3ETS11 A496
IBM-ESXSVPBA300C3ETS11 A496
IBM-ESXSVPBPA300C3EST1 A529
IBM-ESXSVPA036C3-ETS10 A650
IBM-ESXSVPA073C3-ETS10 A650
IBM-ESXSVPA146C3-ETS10 A650
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST336754SS BA1A
IBM-ESXSST373454SS BA1A
IBM-ESXSST3146854SS BA1A
IBM-ESXSST373455SS BA2D
IBM-ESXSST3146855SS BA2D
IBM-ESXSST3300655SS BA2D
IBM-ESXSST373355SS BA38
IBM-ESXSST3146755SS BA38
IBM-ESXSST3300555SS BA38
IBM-ESXSST3146356SS BA4C
IBM-ESXSST3300656SS BA4C
IBM-ESXSST3450856SS BA4C
IBM-ESXSST3300657SS BA58
IBM-ESXSST3450857SS BA58
IBM-ESXSST3600057SS BA58
IBM-ESXSST3750630SS BC1H
IBM-ESXSST31000640SS BC1H
IBM-ESXSST31000424SS BC28
IBM-ESXSST32000444SS BC28
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSGNA073C3ESTT0Z BH0J
IBM-ESXSGNA146C3ESTT0Z BH0J
IBM-ESXSGNA300C3ESTT0Z BH0J
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSBBA036C3ESTT0Z BH0K
IBM-ESXSBBA073C3ESTT0Z BH0K
IBM-ESXSBBA146C3ESTT0Z BH0K
IBM-ESXSMAU3036RC S902
IBM-ESXSMAU3073RC S902
IBM-ESXSMAU3147RC S902
IBM-ESXSMBA3073RC SA0A
IBM-ESXSMBA3147RC SA0A
IBM-ESXSMBA3300RC SA0A
IBM-ESXSMAX3036RC T907
IBM-ESXSMAX3073RC T907
IBM-ESXSMAX3147RC T907

SAS 2.5" (SFF)
Product ID FW

IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST936701SS B51D
IBM-ESXSST973401SS B51D
IBM-ESXSST973402SS B52B
IBM-ESXSST9146802SS B52B
IBM-ESXSST9300603SS B53C
IBM-ESXSST9146803SS B53C
IBM-ESXSST9600204SS B548
IBM-ESXSST936751SS B617
IBM-ESXSST973451SS B617
IBM-ESXSST973452SS B62C
IBM-ESXSST9146852SS B62C
IBM-ESXSST9500430SS BD14
IBM-ESXSST9500620SS BD22
IBM-ESXSST91000640SS BD22
IBM-ESXSCBRBA073C3ETS0 C49C
IBM-ESXSCBRBA146C3ETS0 C49C
IBM-ESXSCBRCA146C3ETS0 C610
IBM-ESXSCBRCA300C3ETS0 C610
IBM-ESXSHUC106030CSS60 D2F8
IBM-ESXSHUC106060CSS60 D2F8
IBM-ESXSST9300503SS E536
IBM-ESXSST9146752SS E625
IBM-ESXSMAV2036RC S116
IBM-ESXSMAV2073RC S116
IBM-ESXSMBB2073RC SB07
IBM-ESXSMBB2147RC SB07
IBM-ESXSMBD2147RC SB1A
IBM-ESXSMBD2300RC SB1A
IBM-ESXSMBC2073RC SC06
IBM-ESXSMBE2073RC SC17
IBM-ESXSMBE2147RC SC17
IBM-ESXSMBF2300RC SB28
IBM-ESXSMBF2600RC SB28


IBM-ESXSMAY2036RC T107
IBM-ESXSMAY2073RC T107

SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WDC WD2502ABYS-23B7A0 02.03B06
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB14
ST3500320NS BB14
ST3750330NS BB14
ST31000340NS BB14
ST3500514NS BB28
ST31000524NS BB28
ST32000644NS BB28
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HDS721025CLA382 JP1OA3GE
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA
WD2003FYYS-23T8B0 01.00D04
WD802ABYS-23B7A0 02.03B05
WD2502ABYS-23B7A0 02.03B07
WD1602ABYS-23B7A0 02.03B07
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31
WD5003ABYX-23 WC31

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V10
ST9160511NS BE18
ST9500530NS BE18
ST9250610NS BE21
ST9500620NS BE21
ST91000640NS BE21

SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2732
STEC M8PSB2 T4 SM04

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0408
STEC M8PSB1 T4 SM15
SG9XCS1B50GMIBM SA03SB63
SG9XCS1F200GEIBM SA03SB63


This package includes new updates to drives with product ID strings of:

SAS 3.5"

- ST31000424SS, ST32000444SS to BC28
Added enhancement for improved RV robustness

- MBE2073RC, MBE2147RC to SC17
- MBA3073RC, MBA3147RC, MBA3300RC to SA0A
Added VPD changes for manufacturing

SAS 2.5" (SFF)

- ST9300603SS, ST9146803SS to B53C
ST9600204SS to B548
SST973452SS, ST9146852SS to B62C
CBRCA146C3ETS0, CBRCA300C3ETS0 to C610
Added fixes for overall drive robustness

- MBD2147RC, MBD2300RC to SB1A
Added VPD changes for manufacturing
Addresses issues seen with DSA HDD Diagnostic test.

- MBF2300RC, MBF2600RC to SB25
Addresses issues seen with DSA HDD Diagnostic test.

- ST9500620SS, ST91000640SS to BD22
HUC106030CSS60, HUC106060CSS60 to D2F8
Inital Release

SATA 3.5"

- WD2502ABYS-23B7A0 , WD1602ABYS-23B7A0 to 02.03B07
Addresses firmware issues that may cause a drive to be marked defunct
prematurely under certain application workloads.

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB14
ST3500514NS, ST31000524NS, ST32000644NS to BB28
Added enhancement for improved robustness

- WD5003ABYX-23 to WC31
Initial Release

SATA 2.5"

- WD3000BLFS-23YBU0 to 04.04V10
(Critical)
Addresses firmware issues that may cause a drive to be marked defunct
prematurely under certain application workloads.


- ST9250610NS, ST9500620NS, ST91000640NS to BE21
Initial Release

SATA 2.5" SSD

- STEC MAC8 IOPS to 2732
STEC M8PSB2 T4 to SM04
Addresses an issue installing RHEL 6.0 onto this drive.

SATA 1.8" SSD

- SG9XCS1B50GMIBM, SG9XCS1F200GEIBM to SA03SB63
Addresses rare issue where the drive may not being seen on
power up.

- STEC M8PSB1 to 0408
STEC M8PSB1 T4 to SM15
Addresses an issue installing RHEL 6.0 onto this drive.

===============================================================

Version 1.08.01
(Critical)

SAS 3.5"
Product ID FW

VPCA300900EST1 A3B8
VPCA450900EST A3B8
VPCA600900EST1 A3B8
VPBA073C3ETS11 A496
VPBA146C3ETS11 A496
VPBA300C3ETS11 A496
VPBPA300C3EST1 A529
VPA036C3-ETS10 A650
VPA073C3-ETS10 A650
VPA146C3-ETS10 A650
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST373455SS BA2D
ST3146855SS BA2D
ST3300655SS BA2D
ST373355SS BA38
ST3146755SS BA38
ST3300555SS BA38
ST3146356SS BA4C
ST3300656SS BA4C
ST3450856SS BA4C
ST3300657SS BA58
ST3450757SS BA58
ST3600057SS BA58
ST3750630SS BC1G
ST31000640SS BC1G
ST31000424SS BC26
ST32000444SS BC26
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
MAU3036RC S902
MAU3073RC S902
MAU3147RC S902
MBA3073RC SA08
MBA3147RC SA08
MBA3300RC SA08
MAX3036RC T907
MAX3073RC T907
MAX3147RC T907


SAS 2.5" (SFF)
Product ID FW

ST936701SS B51D
ST973401SS B51D
ST936701SS B51D
ST973401SS B51D
ST973402SS B52B
ST9146802SS B52B
ST9300603SS B53B
ST9146803SS B53B
ST9600204SS B546
ST936751SS B617
ST973451SS B617
ST973452SS B629
ST9146852SS B629
ST9500430SS BD14
CBRCA146C3ETS0 C370
CBRCA300C3ETS0 C370
CBRBA073C3ETS0 C49C
CBRBA146C3ETS0 C49C
ST9300503SS E536
ST9146752SS E625
MAV2036RC S116
MAV2073RC S116
MBB2073RC SB07
MBB2147RC SB07
MBD2147RC SB19
MBD2300RC SB19
MBC2073RC SC06
MBE2073RC SC16
MBE2147RC SC16
MAY2036RC T107
MAY2073RC T107


SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB13
ST3500320NS BB13
ST3750330NS BB13
ST31000340NS BB13
ST3500514NS BB26
ST31000524NS BB26
ST32000644NS BB26
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
Hitachi HDT725025VLA3 V5DOA7CA
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
WDC WD2502ABYS-23B7A0 02.03B07
WD2502ABYS-23B7A0 02.03B07
WD802ABYS-23B7A0 02.03B05
WD1602ABYS-23B7A0 02.03B05
WD2003FYYS-23T8B0 01.00D04
WD2003FYYS-23W0B0 WA32
WDC WD1003FBYX-23Y7B0 WB31

SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V09
ST9160511NS BE18
ST9500530NS BE18


SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2582

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0405


This package includes new updates to drives with product ID strings of:

SATA 3.5"

- WDC WD2502ABYS-23B7A0 and WD2502ABYS-23B7A0 to 02.03B07
Added enhanced background function to prevent premature
failure of the drive.



===============================================================

Version 1.08.00
(Critical)

SAS 3.5"

- ST373455SS, ST3146855SS, ST3300655SS to BA2D
- ST373355SS, ST3146755SS, ST3300555SS to BA38
- ST3146356SS, ST3300656SS, ST3450856SS to BA4C
- ST3300657SS, ST3450757SS, ST3600057SS to BA58
- ST3750630SS, ST31000640SS to BC1G
- ST31000424SS, ST32000444SS to BC26
(All Above Critical)
These codes addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

- MBA3073RC, MBA3147RC, MBA3300RC to SA08
This code corrects a firmware bug that may cause the drive to not
come ready on a cold boot.

SAS 2.5" (SFF)

- ST973402SS, ST9146802SS to B52B
- ST936751SS, ST973451SS to B617
- ST9146803SS, ST9300603SS toB53B
- ST9600204SS to B546
- ST973452SS, ST9146852SS to B629
- ST9300503SS to E536
- ST9146752SS to E625
- ST9500430SS to BD14
(All Above Critical)
These codes addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

SATA 3.5"

- ST3500514NS, ST31000524NS, ST32000644NS to BB26

- WD2003FYYS-23W0B0 to WA32
- WDC WD1003FBYX-23Y7B0 to WB31
Initial release


SATA 2.5" SSD

- STEC MACH8 IOPS to 2582 (Critical)
Corrects firmware bug that may cause data corruption.
For further information, please refer to retain tip H197650.

SATA 1.8" SSD

- STEC M8PSB1 to 0405 (Critical)
Corrects firmware bug that may cause data corruption.
For further information, please refer to retain tip H197650.


===============================================================

Version 1.07.01
(Critical)

Added support for the following controller:

- IBM 6Gb SSD HBA (68Y7362)

The following is a list of drives and the firmware that they will be
checked for and updated to as necessary.


SAS 3.5"
Product ID FW

VPCA300900EST1 A3B8
VPCA450900EST A3B8
VPCA600900EST1 A3B8
VPBA073C3ETS11 A496
VPBA146C3ETS11 A496
VPBA300C3ETS11 A496
VPBPA300C3EST1 A529
VPA036C3-ETS10 A650
VPA073C3-ETS10 A650
VPA146C3-ETS10 A650
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST336754SS BA1A
ST373454SS BA1A
ST3146854SS BA1A
ST373455SS BA2A
ST3146855SS BA2A
ST3300655SS BA2A
ST373355SS BA36
ST3146755SS BA36
ST3300555SS BA36
ST3146356SS BA4A
ST3300656SS BA4A
ST3450856SS BA4A
ST3300657SS BA56
ST3450757SS BA56
ST3600057SS BA56
ST3750630SS BC1E
ST31000640SS BC1E
ST31000424SS BC21
ST32000444SS BC21
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
GNA073C3ESTT0Z BH0J
GNA146C3ESTT0Z BH0J
GNA300C3ESTT0Z BH0J
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
BBA036C3ESTT0Z BH0K
BBA073C3ESTT0Z BH0K
BBA146C3ESTT0Z BH0K
MAU3036RC S902
MAU3073RC S902
MAU3147RC S902
MBA3073RC SA07
MBA3147RC SA07
MBA3300RC SA07
MAX3036RC T907
MAX3073RC T907
MAX3147RC T907


SAS 2.5" (SFF)
Product ID FW

ST936701SS B51D
ST973401SS B51D
ST936701SS B51D
ST973401SS B51D
ST973402SS B52A
ST9146802SS B52A
ST9300603SS B53A
ST9146803SS B53A
ST9600204SS B544
ST936751SS B616
ST973451SS B616
ST973452SS B626
ST9146852SS B626
ST9500430SS BD13
CBRCA146C3ETS0 C370
CBRCA300C3ETS0 C370
CBRBA073C3ETS0 C49C
CBRBA146C3ETS0 C49C
ST9300503SS E534
ST9146752SS E623
MAV2036RC S116
MAV2073RC S116
MBB2073RC SB07
MBB2147RC SB07
MBD2147RC SB19
MBD2300RC SB19
MBC2073RC SC06
MBE2073RC SC16
MBE2147RC SC16
MAY2036RC T107
MAY2073RC T107


SATA 3.5"
Product ID FW

ST340212AS 3.05
ST380819AS 3.05
ST3160828AS 3.05
ST340014AS 3.48
ST380013AS 3.48
ST3160023AS 3.48
WD2003FYYS-23T8B0 01.00D04
WDC WD2502ABYS-23B7A0 02.03B05
WD2502ABYS-23B7A0 02.03B05
WD802ABYS-23B7A0 02.03B05
WD1602ABYS-23B7A0 02.03B05
ST3500641NS 3.AES
ST3250620NS 3.AEV
ST3500630NS 3.AEV
ST3750640NS 3.AEV
ST3250621NS 4AEV
ST3500631NS 4AEV
ST3750641NS 4AEV
ST3250310NS BB13
ST3500320NS BB13
ST3750330NS BB13
ST31000340NS BB13
ST3500514NS BB26
ST31000524NS BB26
ST32000644NS BB26
HUA721050KLA330 GK6OABDA
HUA721075KLA330 GK8OABDA
HUA721010KLA330 GKAOABDA
HUA722020ALA330 JKAOA3GA
HUA722050CLA330 JP2OA3GB
HUA722010CLA330 JP4OA3GB
HDS725050KLA360 K2AOAT3A
Hitachi HDS721680PLA3 P21OABCA
Hitachi HDS721616PLA3 P22OABCA
HDS728040PLA320 PF1OA6EA
HDS728080PLA380 PF2OA6EA
HDT722516DLA380 V43OA9JA
HDT722525DLA380 V44OA9JA
Hitachi HDT725025VLA3 V5DOA7CA


SATA 2.5"
Product ID FW

WD3000BLFS-23YBU0 04.04V09
ST9160511NS BE18
ST9500530NS BE18


SATA 2.5" SSD
Product ID FW

GBRL0015XVECCM 4.17
GBRL0031XVECCM 4.17
GBRL0015XVEUCM 4.17
GBRLB015XVECCM 4.26
GBRLB031XVECCM 4.26
GBRLB015XVEUCM 4.26
STEC MACH8 IOPS 2366

SATA 1.8" SSD
Product ID FW

STEC M8PSB1 0404


This package includes new updates to drives with product ID strings of:

SAS 3.5"

- VPCA300900EST1, VPCA450900EST, VPCA600900EST1 to A3B8
Initial Release

- VPBPA300C3EST1 to A529
Initial Release

- ST3300657SS, ST3450757SS, ST3600057SS to BA56
(Critical)
Performance improvements under certain workloads.
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.

- ST31000424SS, ST32000444SS to BC21
Initial Release


SAS 2.5" (SFF)

- ST9300603SS, ST9146803SS to B53A
(Critical)
Performance improvements under certain workloads.
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.

- ST9600204SS to B544
(Critical)
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.

- ST973452SS, ST9146852SS to B626
Performance improvements under certain workloads.

- ST9500430SS to BD13
Performance improvements under certain workloads

- ST9300503SS to E534 and ST9146752SS to E623
Performance improvements under certain workloads.

- MBD2147RC, MBD2300RC to SB19 (Critical)
MBE2073RC, MBE2147RC to SC16 (Critical)
Corrects a firmware bug that erroneously reported medium
errors which may cause the drive to report PFA alerts and
in some cases be marked offline

SATA 3.5"

- WDC WD2502ABYS-23B7A0, WD2502ABYS-23B7A0, WD802ABYS-23B7A0,
WD1602ABYS-23B7A0 to 02.03B05 (Critical)
Corrects a firmware bug that may cause the drive to not
come ready on a warm or cold reboot.


- ST3500514NS, ST31000524NS, ST32000544NS to BB26 (Critical)
This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB13
(Critical)
This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.

- HUA722020ALA330 to JKAOA3GA
HUA722050CLA330 to JP2OA3GB
HUA722010CLA330 to JP4OA3GB
Initial Release

SATA 2.5"

- WD3000BLFS-23YBU0 to 04.04V09
(Critical)
This code corrects an additional issue where the drive may be
marked defunct.

- ST9160511NS, ST9500530NS to BE18 (Critical)
This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
For further information, please refer to retain tip H197382.
Also improves performance under certain workloads.


SATA 2.5" SSD

- STEC MACH8 IOPS to 2366 (critical)
Corrects firmware bug that may cause degraded performance
and in some cases the drive may not come ready after a warm or
old boot.

SATA 1.8" SSD

- STEC M8PSB1 to 0404
Turns the default for write cache off
Initial Release

===============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.06
(Critical)

Added support for the following controllers:

- IBM ServeRAID BR10il SAS controller v2 (49Y4731)
- IBM ServeRAID M1015 SAS controller (46M0831)
- IBM ServeRAID M5015 SAS controller (46M0829)
- IBM ServeRAID M5014 SAS controller (46M0916)

This package includes new updates to drives with product ID strings of:

SAS 3.5"

- ST373455SS, ST3146855SS, ST3300655SS to BA2A
ST373355SS, ST3146755SS, ST3300555SS to BA36
(Critical)
These codes addresses a rare potential for data corruption. For this issue
to occur, the drive write cache must be enabled. When a write is issued
while the drive write cache is enabled and a read-verify is performed
immediately afterwards, undetected data corruption can occur. For further
information, please refer to retain tip H194632.

- ST3750630SS, ST31000640SS to BC1E
ST3146356SS, ST3300656SS, ST3450856SS to BA4A
This code address an issue where the drive may report an erroneous
hardware error to the controller.

- MBA3073RC, MBA3147RC, MBA3300RC to SA07
This code improves sequential write performance under certain workloads
when write cache is turned on.

- ST3300657SS, ST3450757SS, ST3600057SS to BA52
NOTE: This is the first code release to be included in the hard drive
update package.

SAS 2.5" (SFF)

- ST973402SS, ST9146802SS to B52A
ST936751SS, ST973451SS to B616
(Critical)
These codes addresses a rare potential for data corruption. For this issue
to occur, the drive write cache must be enabled. When a write is issued
while the drive write cache is enabled and a read-verify is performed
immediately afterwards, undetected data corruption can occur. For further
information, please refer to retain tip H194632.

- MBB2073RC, MBB2147RC to SB07
MBD2147RC, MBD2300RC to SB17
MBE2073RC, MBE2147RC to SC14
CBRCA146C3ETS0, CBRCA300C3ETS0 to C370
This code improves sequential write performance under certain workloads
when write cache is turned on.

- ST9500430SS to BD11
This is the first code release to be included in the hard drive
update package.

SATA 3.5"

- WD2003FYYS-23T8B0 to 01.00D04
This is the first code release to be included in the hard drive
update package.

SATA 2.5"

- WD3000BLFS-23YBU0 to 04.04V08
(Critical)
This code corrects an issue where the drive may generate a false PFA alert.
It also corrects an issue where the drive may be marked defunct

- ST9160511NS, ST9500530NS to BE16
This is the first code releases to be included in the hard drive
update package.

===============================================================
IBM SAS Hard Disk Drive Update Program
Version 1.05

SAS 2.5" (SFF)

ST9xxxx51SS to B616
ST9xxxx02SS to B52A
- This code improves the robustness of write cache operations.

ST9xxxx52SS to B624
ST9xxxx03SS to B536
- This code improves the robustness of write cache operations and
sequential write performance when write cache is enabled

MBD2xxxRC to SB14
- Initial release

SAS 3.5"

ST3xxxxx6SS to BA49
ST3750630SS to BC1D
- This code improves the robustness of write cache operations.

SATA 3.5"

WDC WD2502ABYSxxxxx tp 02.03B04
- Fixes incorrect VPD data

SATA 2.5"

WD3000xxxxx to 04.04V05
- Adjusted PHY setting for better signal quality margin.

SATA 2.5" SSD

STEC MACH8 IOPS to 2269
GBRL0xxxxx to 4.17
GBRLBxxxxx to 4.26
- The new firmware will correct a rare data error condition
in the drives where invalid data may be passed to the system
without any error condition flagged.

Due to the severity of this potential issue, IBM strongly
recommends applying this firmware as soon as possible.

For further information, please refer to retain tip H195663.
=================================================================

IBM SAS Hard Disk Drive Update Program
Version 1.04

SAS 2.5" (SFF)

CBRBAxxxxxx to C49B
- Modified VPD for JSxx Blades

MBBxxxxxx to SB05
- Fixed a performance issue when synchronizing or rebuilding an
array when used in a LSI 1064 based SAS controller

MBC2073RC to SC04
- Fixed a performance issue when synchronizing or rebuilding an
array when used in a LSI 1064 based SAS controller

SAS 3.5"

MBAxxxxxx to SA06
- Fixed a performance issue when synchronizing or rebuilding an
array when used in a LSI 1064 based SAS controller

ST3xxxxx6SS to BA48
- This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
When a write is issued while the drive write cache is
enabled and a read-verify is performed immediately afterwards,
undetected data corruption can occur.
For further information, please refer to retain tip H194632

ST3750630SS to BC1A
- This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
When a write is issued while the drive write cache is
enabled and a read-verify is performed immediately afterwards,
undetected data corruption can occur.
For further information, please refer to retain tip H194632

- Fixes a hang condition during failover operation on a
Bladecenter-S chassis with an RSSM controller.

BBAxxxxxx to BH0K
- Fixes an issue where a drive may prematurely report a PFA trip

GNAxxxxxx to BH0J
- Fixes an issue where a drive may prematurely report a PFA trip


SATA 3.5"

ST31000340NS, ST370330NS, ST3250310NS, ST3500320NS to BB12
- This code addresses a rare potential for data corruption.
For this issue to occur, the drive write cache must be enabled.
When a write is issued while the drive write cache is
enabled and a read-verify is performed immediately afterwards,
undetected data corruption can occur.
For further information, please refer to retain tip H194632

- This code addresses a rare potential for data loss.
After a power cycle, the drive will no longer be available
and becomes unresponsive. Data will become inaccessible due to the
drive not responding.
For further information, please refer to retain tip H194623.


WDC WD2502ABYSxxxxx tp 02.03B04
- Fixes incorrect VPD data

SATA 2.5"

WD3000xxxxx to 04.04V04
- Fixes a Critical issue - IBM recommends a backup of the data
on the drive before attempting to update the firmware.
This is a fix for an issue where data required for spinup of the
drive may be overwritten rendering the drive inoperable on a
subsequent warm or cold system reboot.

- Fixes a issue with an internal timer that may cause drive to
go offline when used in a non-raid environment.

SATA 2.5" SSD

STEC MACH8 IOPS to 2103
- Initial Release

=================================================================

IBM SAS Hard Disk Drive Update Program
Version 1.03

Added support for the following controllers:

IBM ServeRAID MR10il SAS Controller
IBM ServeRAID MR10is SAS Controller
IBM ServeRAID BR10i SAS Controller
IBM ServeRAID BR10il SAS/SATA Controller
IBM SAS/SATA RAID Kit
IBM SAS Expansion Card (CFFv) for IBM BladeCenter
IBM SAS Connectivity Card (CFFv) for IBM BladeCenter

New updates to drives with product ID strings of:

SAS 2.5" (SFF)

ST9146802SS, ST973402SS to B529
- Added support for JS2x Blades in a Bladecenter-S chassis
- Picked up the latest network roll of firmware fixes to
address some unexpected system hangs,

ST936751SS, ST973451SS to B615
- Added support for JS2x Blades in a Bladecenter-S chassis
- Picked up the latest network roll of firmware fixes to
address some unexpected system hangs,

CBRBAxxxxxx to C495
- Initial release

MBBxxxxxx to SB04
- Initial release

MBC2073RC to SC03
- Initial release

SAS 3.5"

VPBAxxxxxx to A496
- Added support for JS2x Blades in a Bladecenter-S chassis

ST3146855SS, ST3300655SS, ST373455SS to BA29
- Added support for JS2x Blades in a Bladecenter-S chassis
- Picked up the latest network roll of firmware fixes to
address some unexpected system hangs,

ST3450856SS to BA47
- IBM was notified by our vendor that there is a defect in
a level of firmware used in the IBM 450GB 15K SAS 3.5" HS HDD
(PN 41Y8454) in option 42D0519, which under certain conditions
may lead to data being written or read back incorrectly on the
drive. IBM has worked closely with the vendor to identify the
problem and developed a firmware fix to resolve the problem.
Customers should upgrade to firmware level BA47

MBAxxxxxx to SA05
- Initial release

ST3750630SS to BC17
- Initial release


SATA 3.5"

ST3250620NS, ST3500630NS, ST3750640NS to 3.AEV

ST3250621NS, ST3500631NS, ST3750641NS to 4AEV

ST31000340NS, ST3750330NS, ST3250310NS, ST3500320NS to BB10
- Initial release

HUA721050KLA330, HUA721075KLA330, HUA721010KLA330, to AB4A
- Initial Release

SATA 2.5" SSD

GBRL001xxx, GBRL0031xxx to 4.14
- corrects intermittent hangs during operations
=============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.02

Support of ServeRaid 8s Raid controller
Support of ServeRaid 10i Raid controller
Support of ServeRaid 10k Raid controller
Support of ServeRaid 10m Raid controller
Support of LSI 1078 SAS controller
Support of SATA drives attached to SAS controllers

Support and updates to drives with product ID strings of:

VPAxxxxxx to A650
Change to improve performance in sequential write workloads
Improvements to internal drive logging and media checking.
Critical Fix:
This code addresses a rare potential for data loss
This code update should be applied to prevent the event from occurring.

ST340XXXAS and ST380XXXAS to 3.48
Fix to address Read Log Command abort error.

ST340XXXAS, ST380XXXAS and ST3160XXXAS to 3.05
Fix to address intermittent hard drive no-shows
after system comes out of hibernation.

ST3500641NS to 3.AES
Changes to the refresh rate of the DRAM used on the drive.

ST3500640NS to 3.AEJ
Initial release.

HDTXX... & HDSXX... codes go to Masked ROM version.
HDS725050KLA360 to AQ1A to also
Fix an issue that occurs while running in NCQ mode with
write cache disabled.

ST3xxxx4SS to BA26
Improves intialization times with some ServeRaid controllers
Performance improvements under some sequential workloads.

ST3xxxx5SS to BA35
Improves intialization times with some ServeRaid controllers

ST9xxx51SS to B612
Intial release of firmware

ST9xxxx2SS to B526
Improves intialization times with some ServeRaid controllers

MAUxxxx and MAXxxxx
Added support for new SAS features required by new SAS controllers.

==============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.01
Please refer to RETAIN tip H186019.

Support of ServeRaid 8e Raid controller
Support of ServeRaid 8k Raid controller
Support of ServeRaid 8l Raid controller
Support of on-board LSI 1064 controller
IBM MegaRaid 8480 Raid Controller

Firmware updates to drives with Product ID strings:

GNAxxxx and BBAxxxx to BH0G
Picks up the latest network roll of firmware fixes
to improve performance under some sequential workloads
and improvements to signal quality parameters.

ST9xxxx to B51D amd ST3xxxx to BA18
Picks the latest network roll of firmware fixes
to address unexpected system hangs and some
performance improvements.

MAVxxxx to S116 and MAYxxxx to T107
Picks up the latest network roll of firmware fixes
and to improve signal quality parameters.

MAXxxxx to T904
Initial release
============================================================

IBM SAS Hard Disk Drive Update Program
Version 1.00
Initial Release

Support of Adaptec 48xxx based controllers
Support of ServeRaid 8i Raid controller
Support and updates to drives with product ID strings of:
ST936701SS
ST973401SS
ST336754SS
ST373454SS
GNAxxxxx
BBAXXXXX

ibm_fw_hddlegacy_sas-1_22_00_linux_32-64_chg