QLogic 10Gb Converged Network Adapter (NIC) for System x and Blades Release Notes October 5, 2013
This software license applies only to QLogic customers. QLogic Corporation. All rights reserved.
Table of Contents
1. Version 2. Changes 3. Fixes 4. Known Issues 5. Additional Information 6. Firmware (Embedded in CNA) 7. Trademarks 8. Notices 9. Contacting Support
1. Version
This is NIC driver release version 1.00.00.32, package version 1.00.00.32.a.
These release notes describe the changes, fixes, known issues, and release details that apply to the QLogic FCoE Adapter driver version for SLES 11 Linux Driver with Kernel 2.6.x.
2. Changes
The following changes have been made to the Converged Network Adapter Networking Driver Update for Linux Kernel 2.6.x:
* Enabled ethtool WoL support * Fixed ethtool loopback test hang * Fixed stat counter
Hardware Support
* QLE8142 PCI-Express to 10Gb FCoE Converged Network Adapter * QMI8142 PCI-Express to 10Gb FCoE Converged Network Adapter
OS Support
These drivers work with the following Linux kernel 2.6.x distributions
* Novell SuSE Linux Enterprise Server 11
Software Components
* Driver 1.00.00.32 for SLES 11
Industry Standards Compliance
N/A
3. Fixes and Enhancements:
Fixed issure where "FC link not coming up after cable pull, only when QLGE module has been loaded."
4. Known Issues
The following known issues may be observed in the Converged Network Adapter Networking Driver Update for Linux Kernel 2.6.x:
Driver Compilation ------------------
When trying to compile the driver by running make install, the following error may occur:
"Linux kernel source not configured - missing version.h"
To resolve this issue, create the version.h file by going to the Linux source tree and entering the following:
make include/linux/version.h
Jumbo Frames System Requirement -------------------------------
Memory allocation failures have been observed on Linux systems that are running Jumbo frames with 64MB of RAM or less. If you are using Jumbo frames, your system may require more than the advertised minimum requirement of 64MB of system memory.
Performance Degradation with Jumbo Frames -----------------------------------------
Degradation in throughput performance may be observed in some Jumbo frames environments. If this is observed, increasing the application's socket buffer size and/or increasing the /proc/sys /net/ipv4/tcp_*mem entry values may help. For more details, see the specific application manual and /usr/src/linux*/Documentation/networking/ip-sysctl.txt.
Multiple Interfaces on Same Ethernet Broadcast Network ------------------------------------------------------
Due to the default ARP behavior on Linux, it is not possible to have one system on two IP networks in the same Ethernet broadcast domain (non-partitioned switch) behave as expected. All Ethernet interfaces will respond to IP traffic for any IP address assigned to the system. This results in unbalanced receive traffic.
If you have multiple interfaces in a server, do either of the following:
* Turn on ARP filtering by entering the following:
echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
* Install the interfaces in separate broadcast domains: either in different switches or in a switch partitioned to VLANs.
UDP Stress Test Dropped Packet Issue ------------------------------------
Under small packets UDP stress test with 10GbE driver, the Linux system may drop UDP packets due to the fullness of socket buffers. You may want to change the driver's Flow Control variables to the minimum value for controlling packet reception. Or, you can increase the kernel's default buffer sizes for UDP by changing the values in /proc/sys/net/core/rmem_default and rmem_max.
Unplugging Network Cable While ethtool -p is Running ----------------------------------------------------
In kernel versions 2.5.50 and later (including 2.6 kernel), unplugging the network cable while ethtool -p is running will cause the system to become unresponsive to keyboard commands, except for CTRL+ALT+DEL. Restarting the system appears to be the only remedy.
Bonding Configuration ---------------------
While creating the bond, issue the following command:
modprobe -v bonding fail_over_mac=1
Then rebuild the initrd and reboot the system.
5. Additional Information
N/A
6. Firmware
N/A (The Ethernet driver does not have firmware embedded.)
7. Trademarks
QLogic, the QLogic logo, QLA, SANbox, and SANsurfer are registered trademarks of QLogic Corporation.
SANtrack and SAN Express are trademarks of QLogic Corporation.
All other brand and product names are trademarks or registered trademarks of their respective owners.
8. Notices
Information furnished in this document is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are only for illustrative purposes. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
9. Contacting Support
Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance. QLogic Technical Support can be reached by the following methods:
(c) Copyright 2013. All rights reserved worldwide. QLogic, the QLogic logo, and the Powered by QLogic logo are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners. qlgc_dd_nic_qlge-1_00_00_32_a_sles11_32-64_chg
Firmware Version: 2.01a11 Boot Code Version: 5.12a13 Supported On: IBM System x and BladeCenter
Problems Fixed: - Emulex FC Adapter does not auto-enable SAN boot mode when boot target configuration is made via IFM (BOFM) - Emulex FC configuration utility is in the wrong F1 setup screen - IBM CIOv adapter connected to Brocade 8 Gig FC BladeCenter switch intermittently Links up at less than 8 Gig
Firmware Version 2.01a3 Boot Code Version: 5.12a5 Supported On: IBM System x and BladeCenter
Incremental Interoperability: - Enhanced timeout notifications for processing abort failures.
Problems Fixed: - All multi-abort I/Os are returned on the same ring from which the ABORT_MXRI command was received. - Changed the TRCV response in the abort state to CMD RJT to enable the TRSP to be processed. - Corrected an issue with blocked TSEND operations. - Corrected a buffer leak issue with RRQ exchanges. - Corrected an issue where the TRCV IOCB was de-queued improperly causing a XFR_RDY flood. - Corrected an issue where the OXID field was not loaded in the XRI_ABORTED IOCB. - Corrected an issue in recognizing whether an EEPROM is present.
This is the combined Release Notes of each individual components for firmware. Please see section relating to component of interest.
Kit Version 2.02.06
Q8I20206.BIN contains: ---------------------- * BIOS version 3.24 * UEFI version 3.47 * Fcode version 3.20 (PPC) * PXE Boot version 1.17 * NIC EFI version 1.10 * NIC Fcode version 80.01 * Firmware version 7.01.00 * MPI version 1.40.08 * EDC PHY version 1.08.00
MPI CFG version Rev. L FlasUtil version 1.89 VPD version 10.00a Efiutil/x64 version 3.17
Q8I20202.BIN contains: ---------------------- * BIOS version 3.20 * UEFI version 3.44 * Fcode version 3.20 (PPC) * PXE Boot version 1.17 * NIC EFI version 1.10 * NIC Fcode version 80.01 * Firmware version 7.00.01 * MPI version 1.40.08 * EDC PHY version 1.08.00
MPI CFG version Rev. L FlasUtil version 1.89 VPD version 10.00a Efiutil/x64 version 2.86
Q8I20100.BIN contains: ---------------------- * BIOS version 3.20 * UEFI version 3.44 * Fcode version 3.20 (PPC) * PXE Boot version 1.17 * NIC EFI version 1.08 * NIC Fcode version 80.01 * Firmware version 5.10.00 * MPI version 1.40.08 * EDC PHY version 1.08.00
MPI CFG version Rev. L FlasUtil version 1.89 VPD version 10.00a Efiutil/x64 version 2.86
Q8Q10042.BIN contains: ---------------------- * BIOS version 2.11 * UEFI version 3.12 * Fcode version 3.02 * Firmware version 5.01.02 * MPI version 1.35.02 * PXE Boot version 1.03 * NIC EFI version 1.02
1. Change History 2. Known Issues 3. Notices 4. Contacting Support
1. Change History
These release notes describe the changes, fixes, known issues, and release details that apply to the FC-FCoE BIOS for 2600 series and 8300 series adapters version 3.24.
This section contains:
* 1.1 Version * 1.2 Changes * 1.3 Bug Fixes
1.1
Version 3.24 * Removed Beta Banner
Version 3.24 Beta 1 Changed Banner to display 'FCoE' for Schultz (ER110784). Added additional time to login target when called after EFI driver unloads. (ER110755,ER110855)
Version 3.23 * Removed Beta Banner
Version 3.23 Beta 2 Added code to handle boot LUN GT then 255 (ER109195).
Version 3.23 Beta 1 * Added support for Helga.
Version 3.22 * Added code to display message when 64 bit address detected.
Version 3.21 * Removed Beta Banner
Version 3.21 Beta 1 * Added support for Execution Throttle for P3P (ER106372) * Added code to not display connection options for Hilda Trinity adapter. * Check for invalid LUN in CTRL-Q scan devices.
Version 3.20 * Fixed bug in CTRL_Q utility that could cause some cosmetic display issues. * Add Hilda CLP _hss support. * Configure ISP24xx if on slot 0. * Added "QLogic" to PnP productid (ER104424) * Check for 4G flag in NVRAM for Hilda FC.(ER104714)
Version 3.19 * Removed Beta Banner
Version 3.19 Beta 1 * Fixed bug with CTRL-Q Loopback Utility (ER100729).
Version 3.18 * Removed Beta Banner
Version 3.18 * Added code to check/program Feature Config checksum. * Fix bug that could cause buffer overrun in CTRL-Q with Report Lun command (ER100294). * Added check for PCI address change when updating option card data structure.
Version 3.18 Beta 1 * Changed code to use 32 bit pointer to allocate/deallocate EBDA memory. * Added code to check/program Feature Config checksum.
Version 3.17 * Removed Beta Banner
Version 3.17 Beta 1 * Fixed cosmetic issue in displaying data rate in CTRL-Q
Version 3.16 * Changed text for 8300 series adapter External loopback (ER98690). * Fixed display issue with CTRL-Q Diskutility(ER98727) * Fixed Lun select issue with CTRL-Q (ER98675).
Version 3.15 * Removed Beta Banner
Version 3.14 Beta 3 * Fixed bug in displaying selectable boot lun (ER98226) * Removed 4G data rate option for OEM adapter (ER98228) * Limit leading '0's in CTRL-Q menu (ER98389). * Set 'Aggressive Cooling' flag for OCSD. * Enabled Personality Change option.
Version 3.14 Beta 2 * Fixed issue with not restoring defaults on port 1 (ER 97619) * Fixed issue with serdes data saved incorrectly. (ER 97654) * Added code to limit Report Lun List size to 256 luns Version 3.14 Beta 1 * Added check for 0 lun count when selecting device (ER 97385) Version 3.14 * Removed 'Beta' from banner Version 3.13 Beta 17 * Disable Personality Change option in CTRL-Q. * Fixed bug with WWNN handling for MCTP.(ER 96920) Version 3.13 Beta 16 * Added check for Set MD2 set to 0 (restore defaults) (ER96912) * Added code to reset Port Config after Internal loopback test for 8300 series adapter(FCoE). Version 3.13 Beta 15 * Added support for 16 bit lun (ER96090). Version 3.13 Beta 14 * Add support for Set MD2 CLP string. Version 3.13 Beta 13 * Added code to issue Load Flash FW (3) MB command for 8300 series adapter as part ISP start sequence. (ER 94035). Version 3.13 Beta 12 * Fixed code to prevent async event from causing BIOS to hang when scanning for devices (ER94371). * Added check for Internal Loopback mode when connected to F-Port (ER71773). * Added check for 8300 series adapter FW Auto Load when re-initing ISP. * Version 3.13 Beta 11 * Fix code to disable ALT+1 Hotkey (ER92844) . * Fixed CTRL-Q code mailbox timeout (ER92957). Version 3.12 Beta 10 * Added warning message in Personality change screen Version 3.12 Beta 9 * Updated BIOS to version 3.12 of non-8300 series adapter BIOS Version 3.12 Beta 8 * Update 8300 series adapter BIOS code with version 3.11 fixes
Version 3.11 * Removed check for Virtual Address flag on Cold Boot.
Version 3.10 * Changed code to check for signature aaaaaaaah before* updating virtual mac address.
Version 3.09 * Changed code to ignore soft boot signature aaaaaaaah*
Version 3.08 * Added code to save device number in OCSD.
Version 3.07 * Added code to read cold boot register signature to determine when BIOS should update/restore virtual Mac address.
Version 3.06 * Fixed bug where retry count was not always being updated.
Version 3.05 * Added code to support ECHO lopback command.
Version 3.04 * Removed Beta from banner.
Version 3.04 Beta 4 * Fixed bug in clp_hss processing. * Updated some ETOC header data fields.
Version 3.04 Beta 3: * Changed code passing Sensor Data pointer
Version 3.04 Beta 2 * Added support for passing ETOC pointer. * Added support for posting port status for EFI use.
Version 3.04 Beta 1 * Added support for sensor data reporting.
Version 3.03 * Added support NCSI Flex Address.
Version 3.02 * Fixed bug in setting mailbox timeout for TUR.
Version 3.01 * Removed CTRL-Q Loopback test for P3P.
Version 3.00 * Removed Beta banner
Version Beta 14 * Added code to get serial number from VDP data for ISP2532. * Fixed bug is display loopback error status.
Version Beta 13 * Fixed bug in verifying FW for non-P3P HBA's. * Removed QLogic vendor id from BIOS banner. * Added retry for LLIOCB when status subcode is 4.
Version Beta 12 * Fixed bug in not setting up retry count for P3P.
Version Beta 11 * Added support for -LR option * Changed error message when no ISP Functions found.
Version Beta 10 * Added code to check for Wocket card.
Version Beta 9 * Fixed bug with not clearing P3 Async Event.
Version Beta 8 * Added additional check for P3 INIT Complete.
Version Beta 7 * Increased p3_busy_wait delay
1.2 Changes
The following changes have been made to the BIOS for FC-FCoE Adapters between versions 3.02 and 3.24.
* Changed Banner to display 'FCoE' for Schultz (ER110790). * Added additional time to login target when called * after EFI driver unloads. (ER110755.ER110855) * Added support for Helga. * Added code to display message when 64 bit address detected. * Added support for Execution Throttle for P3P (ER106372) * Added code to not display connection options for Hilda Trinity adapter. * Check for invalid LUN in CTRL-Q scan devices. * Fixed bug in CTRL_Q utility that could cause some cosmetic display issues. * Add Hilda CLP _hss support. * Configure ISP24xx if on slot 0. * Added "QLogic" to PnP productid (ER104424) * Check for 4G flag in NVRAM for Hilda FC.(ER104714) * Fixed bug with CTRL-Q Loopback Utility (ER100729). * Added code to check/program Feature Config checksum. * Fix bug that could cause buffer overrun in CTRL-Q with Report Lun command (ER100294). * Added check for PCI address change when updating option card data structure. * Changed code to use 32 bit pointer to allocate/deallocate EBDA memory. * Added code to check/program Feature Config checksum. * Fixed cosmetic issue in displaying data rate in CTRL-Q * Changed text for Hilda External loopback (ER98690). * Fixed display issue with CTRL-Q Diskutility(ER98727) * Fixed Lun select issue with CTRL-Q (ER98675). * Fixed bug in displaying selectable boot lun (ER98226) * Removed 4G data rate option for OEM adapter (ER98228) * Limit leading '0's in CTRL-Q menu (ER98389). * Set 'Aggressive Cooling' flag for OCSD. * Enabled Personality Change option. * Fixed issue with not restoring defaults on port 1 (ER 97619) * Fixed issue with serdes data saved incorrectly. (ER 97654) * Added code to limit Report Lun List size to 256 luns * Added check for 0 lun count when selecting device (ER 97385) * Disable Personality Change option in CTRL-Q. * Fixed bug with WWNN handling for MCTP.(ER 96920) * Added check for Set MD2 set to 0 (restore defaults) (ER96912) * Added code to reset Port Config after Internal loopback test for Hilda(FCoE). * Added support for 16 bit lun (er96090). * Add support for Set MD2 CLP string. * Added code to issue Load Flash FW (3) MB command for Hilda as part ISP start sequence. (ER 94035). * Fixed code to prevent async event from causing BIOS to hang when scanning for devices (er94371). * Fix code to disable ALT+1 Hotkey (er92844) . * Fixed CTRL-Q code mailbox timeout (er92957). * Added warning message in Personality change screen. * Updated BIOS to version 3.12 of non-hilda BIOS * Removed check for Virtual Address on Cold Boot. * Changed code to check for signature aaaaaaaah before updating virtual mac address. * Changed code to ignore soft boot signature aaaaaaaah * Added code to save device number in OCSD. * Added code to read cold boot register signature to determine when BIOS should update/restore virtual Mac address. * Fixed bug where retry count was not always being updated. * Added code to support ECHO lopback command. * Added support NCSI Flex Address.
1.3 Bug Fixes
The following fixes have been made to the BIOS for FC-FCoE Adapters between versions 3.00 Beta 7 and 3.24.
* Changed Banner to display 'FCoE' for Schultz (ER110790). * Added additional time to login target when called * after EFI driver unloads. (ER110755.ER110855) * Added code to handle boot LUN GT then 255 (ER109195). * Check for invalid LUN in CTRL-Q scan devices. * Fixed bug in CTRL_Q utility that could cause some cosmetic display issues. * Add Hilda CLP _hss support. * Configure ISP24xx if on slot 0. * Added "QLogic" to PnP productid (ER104424) * Check for 4G flag in NVRAM for Hilda FC.(ER104714) * Fixed bug with CTRL-Q Loopback Utility (ER100729). * Added code to check/program Feature Config checksum. * Fix bug that could cause buffer overrun in CTRL-Q with Report Lun command (ER100294). * Added check for PCI address change when updating option card data structure. * Changed code to use 32 bit pointer to allocate/deallocate EBDA memory. * Added code to check/program Feature Config checksum. * Fixed cosmetic issue in displaying data rate in CTRL-Q * Changed text for Hilda External loopback (ER98690). * Fixed display issue with CTRL-Q Diskutility(ER98727) * Fixed Lun select issue with CTRL-Q (ER98675). * Fixed bug in displaying selectable boot lun (ER98226) * Removed 4G data rate option for OEM adapter (ER98228) * Limit leading '0's in CTRL-Q menu (ER98389). * Set 'Aggressive Cooling' flag for OCSD. * Fixed issue with not restoring defaults on port 1 (ER 97619) * Fixed issue with serdes data saved incorrectly. (ER 97654) * Added code to limit Report Lun List size to 256 luns * Added check for 0 lun count when selecting device (ER 97385) * Disable Personality Change option in CTRL-Q. * Fixed bug with WWNN handling for MCTP.(ER 96920) * Added check for Set MD2 set to 0 (restore defaults) (ER96912) * Added support for 16 bit lun (er96090). * Add support for Set MD2 CLP string. * Added code to issue Load Flash FW (3) MB command for Hilda as part ISP start sequence. (ER 94035). * Fixed code to prevent async event from causing BIOS to hang when scanning for devices (er94371). * Fix code to disable ALT+1 Hotkey (er92844) . * Fixed CTRL-Q code mailbox timeout (er92957). * Added warning message in Personality change screen. * Updated BIOS to version 3.12 of non-hilda BIOS * Removed check for Virtual Address on Cold Boot. * Changed code to check for signature aaaaaaaah before updating virtual mac address. * Changed code to ignore soft boot signature aaaaaaaah * Added code to save device number in OCSD. * Added code to read cold boot register signature to determine when BIOS should update/restore virtual Mac address. * Fixed bug where retry count was not always being updated. * Added code to support ECHO lopback command. * Fixed bug in clp_hss processing. * Updated some ETOC header data fields. * Changed code passing Sensor data pointer * Added support for passing ETOC pointer. * Added support for posting port status for EFI use. * Added support for sensor data reporting. * Added support NCSI Flex Address. * Fixed bug in setting mailbox timeout for TUR. * Increased p3_busy_wait delay * Added additional check for P3 INIT Complete. * Fixed bug with not clearing P3 Async Event. * Added code to check for Wocket card. * Added support for -LR option * Changed error message when no ISP Functions found. * Fixed bug in not setting up retry count for P3P. * Fixed bug in verifying FW for non-P3P HBA's. * Removed QLogic vendor id from BIOS banner. * Added retry for LLIOCB when status subcode is 4. * Added code to get serial number from VDP data for ISP2532. * Fixed bug is display loopback error status. * Fixed bug in setting mailbox timeout for TUR.
2. Known Issues
None
3. Notices
Information furnished in this document is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are only for illustrative purposes. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
4. Contacting Support
For further assistance, contact QLogic Technical Support at: http://support.qlogic.com
Trademarks
Accelera, Accelerating Cluster Performance, InfiniCon Systems, InfiniNIC, InfiniPath, InfiniView, QLA, QLogic, the QLogic logo, ReadyPath, SANdoctor, SANsurfer, and SilverStorm are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.
(c) Copyright 2013. All rights reserved worldwide. QLogic and the QLogic logo are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.
1. Change History 2. Known Issues 3. Notices 4. Contacting Support
1. Change History
UEFI Driver:
version 3.44 (3/30/13) * Fixed potential flash corruption bug. Updated FlashProgramSafe to correctly calculate FlashBlockEnd. (ER 105595)
version 3.43 (2/28/13) * Appending MBI version info at the end of bootcode images (Fc, NIC) (ER 0101636)
version 3.42 (10/08/12) * Add support for Firmware Management Protoocl [ER 97831] * Add support for Driver Health Protocol [ER 97831] * Add fix to make Driver SCT 2.3 Compliance [ER 97831]
version 3.41 (4/4/12) * Add support for different callback action in callback () [ER 91949] * Use device handle (instead of virtual handle)[ER 91949] * Fixed param write bug [ER 91949]
version 3.40 (2/8/12) * Driver no longer sets the IO attribute bit in the PciIO Attributes() call. The IO attribute caused problems on certain systems. The driver does not do IO accesses. (ER84909)
version 3.39 (3/11/11) * Added Macronix MX25L3206E flash part support. (ER80795) * Disabled flash write protect check. (ER80795)
Efiutil:
version 3.17
* Add fix for 25xx ver_info command (ER 104543)
version 3.16
* Removed hardcoded subystem id check (ER0103883) * Replaced with MBI image traverse for ssid match (ER0103883)
version 3.15
* Fixed ambiguity in firmware version display. (ER0103456)
2. Known Issues
Driver: * In the HII menus, Adding/Deleting a Target/LUN will require a reboot for changes to take effect.
3. Notices
Information furnished in this document is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are only for illustrative purposes. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
4. Contacting Support
For further assisance, contact QLogic Technical Support at: http://support.qlogic.com
Trademarks
Accelera, Accelerating Cluster Performance, InfiniCon Systems, InfiniNIC, InfiniPath, InfiniView, QLA, QLogic, the QLogic logo, ReadyPath, SANdoctor, SANsurfer, and SilverStorm are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.
(c) Copyright 2013. All rights reserved worldwide. QLogic, the QLogic logo, and the Powered by QLogic logo are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.
******************* QLogic Fcode for IBM CNAs ***************** Release Notes
QLogic FCoE FCode for 81xx CNA Release Notes QLogic Corporation. All rights reserved.
Table of Contents
1. Changes 2. Known Issues 3. Notices 4. Contacting Support
1. Change History
These release notes describe the changes, fixes, known issues, and release details that apply to the multi-boot package for the 81xx Converged Network Adapter (CNA) FCode version 3.00.
1.1. FCode Version History
version 3.20 01/11/13 * ER102374: Display Product-ID string in VPD area during initial selection. * ER94574: Fix stack bug in .adatper-info, found in blade hotplug test by efcode
version 3.19 04/09/12 * Add NVRAM Fcode-parameter enab_dcbx_to bit. Must be set to enable Boeing fix. * Add check for MBAR2 (Multi-Queue memory) and create reg property if it exists.
version 3.18 03/30/12 - Special build for Boeing * Make validate-nvram silent. Print messages only if debug-flash?(x1000) is set. * Added mpicfg.fth file to handle all MPI-CFG access methods for Boeing fix. * Added check-poll-dmae word at probe-time to insure Poll-DMA-Engine bit is set. * Added dynamic sizing of the BAR registers at probe-time for reg property. * Remove dis-exp (disable-exprom) in ena-reg-acc. Causes problem on SPARC T3-1B. * Change oem property to QLogic or Oracle, and manufacture property to QLogic. * Fix bugs in search of Card-Type-Lists for SSDID when flashing w/find-ilt-code.
version 3.17 12/01/11 * Stripped ISP2400 & SUN specific code using #ifdefs to reduce IBM size by .5KB * Added EDC FW area in Flash and added write-sfp and read-sfp mailbox commands
version 3.16 09/30/11 * Change PCI-Cmd-Reg value, pci-cmdv, to x146. Add System Error Resp Enable. * Change MBAR0 size (/regs) from x1000 to x4000 to include MSI-X table. * Add setting Prefetchable bit if enabled for MBAR0 in map-ifp-regs(read-bar). * Fix close-hardware to logout-devices if Link-up?, not done-fw-init? flag. * Add "Problem fixed" printout when validate-nvram fixes the backup copy. * Change init-image & init-fw to return error? flag on stack so you can abort. * Fix all mboxs commands to write 0 to all mboxes used by FW, don't assume =0. * Add clr-flags after a wait-for-risc-int timeout, which will restart the FW. * Change all Copyright messages to: "Copyright 1999-2011". * Fix typo in 'adapter' property for the QLE8152. Was Single, now is Dual. * Change mbox-test to actually do some pattern testing and compare data. * Added 31 second SW timeout for IOCB & mailbox commands in wait-for-risc-int. * Add retry SCSI command once if IOCB timeout & 8048 Recv. error AEN received. * Fix stop-fw mailbox command. Clear Bit 1 (Transition to ROM Code) in Mbox-1. * Add show-fcfs, set-mac-am and set-vlan-id to show-commands. * Add to FC_FcodeReadme SPARC & PPC: set-vlan-id, set-mac-am and show-fcfs.
* Utility/Debug changes 1 Change version method for INIT only version to also show FW version. 2 Change find-ilt-code to check Chip-Rev & Card-Type-List in ILT header search 3 Change ilt-valid? to check for Signature Word "QILT" and ILT veersion field 4 Add "Load Raw FW image?" prompt and max-FW-code-size check to ldfw method. 5 Add debug? option debug-probe? (x10000) to disable card access during probe. 6 Fix bug in flash utility which was not setting my_did if the FLT is invalid.
version 3.15 09/29/10 * Fix selftest to leave connection-mode=P2P for IBM Mezz cards only (ER71793). * Change: use the NIC MAC-Adr +1 instead of Enode-MAC-Adr (Schultz only). * Enable LR BB-Credit if this enhanced-feature is set in NVRAM (Schultz only).
* Utility/Debug changes 1 Add debug? flag: 8000= Dump all mailboxes on all AENs and all Mbox commands. 2 Fix problem in ldfcode Flash utility. INIT version was not setting my_did. 4 Add capability to flash Schultz raw Firmware binary file to the ldfw method.
* Boot-wait-time related changes 1 Change boot-wait-time back to v3.12. Now link-down-to will wait if enabled. 2 Change device-present? to exit immediately if the link-up? flag is not true. 3 Fix show-children to not use boot-wait-time for link-down-to timeout value. 4 Fix device-present? to not restart BW-timer. Start-time set in isp-fw-ready?.
version 3.14 04/30/10 * Change validate-nvram to compare only the NVRAM area, not the entire sector. * Change all Copyright messages to: "Copyright 1999-2010, QLogic Corporation". * Change makefile to used the DID variable for the File name & in PCI header. * Add the capability to flash NIC Fcode on Schultz CNAs using ldutil/ldfcode. * Changed file name: isp-init.flt > init-isp.fth.
version 3.13 03/26/10 * Remove Hard-RICS-reset from reset-risc method & add 100ms delay after reset. * Make old-sb (old sec-buf) an instance value. Problem on M3000 (ER70453). * Fix Explicit logout-device IOCB to include the ISP PortID and Port WWN. * Change login-devices to not logout with FC_Initiators.
* Boot-wait-time related changes * Change get-to-params to set boot-wt = 8 secs if boot-wait-time is disabled. * Change set-boot-wait-time to not affect link-down-to (timeout) for Fujitsu. * Change set-boot-wait-time to be entered/display in decimal, not hex(Fujitsu).
* Additions made for debugging: 1 Changed debug? flags: 4000= Got-R2H-intr, 2000= IOCB-Dump, 800=FW-Ready-wait 2 Add Parameter 1 debug display on login IOCB faliure. 3 Add force-open-ok? test flag in open method. Default = true(no real change). * Changes to make process and Flash utilities: 1 Use OpenBIOS Toke Tokenizer to make isp2500/8100/8200. isp2400 uses SUN toker. 2 Add Sun-Style-Checksum option OpenBIOS Toke for all SUN isp2500/8100/8200. 3 Restructure fcode source files. Add: isp-init.fth, p3-init.fth, mailbox.fth, properties.fth, structs.fth, regs-isp.fth, regs-p3.fth, utils.fth.
Version 3.12 01/11/10 * Fixed sunid (SUNW,qlc) for the SUN CNA QLE8142. The SSDID is 183, not 182. * Add flashing support for mpi-config-image from Image-Layout-Table(ILT) File. * Add check for Card-Type & Swap bits in Image-Layout-Table(ILT) Flash utility.
Version 3.11 12/11/09 * Add support for Sun (SUNW,qlc) CNA QEM8152.
Version 3.10 12/02/09 * Add support for Sun (SUNW,qlc) CNAs QLE8140, QlE8142, QLE8150, & QLE8152.
Version 3.09 * Fix Node-Name-Option bit preservation in restore-default-settings.
Version 3.08 * Fix default WWNN & WWPN preservation in restore-default-settings. * Add standard properties. Use m4 utility to automaticly create date string. * Add file rev_level.m4 which has the revision level strings only. * Remove "SFP state: Unknown" message (.isp) if the adapter is IBM mezz card. * Change messages "Login failed" to "Login Abort". "Error Subcode" to "Subcode". * Remove patch of PCI header image size byte at offset 0x2c from init version.
Version 3.07 * Fix read-cap16-cmd. Used when the LUN size is >2TB (i.e. #blocks > 32-bits). * Fix disk-test to work with large (>2TB) LUNs, where the LBA > 32-bits. * Remove command retry when 8048 AEN is received.
Version 3.06 * Add option for qlgc-debug? in nvramrc. If the diag-switch? is true, then the debug? flag is set is set to the value of qlgc-debug?. * Add lba64 large disk capability (read-blocks64 write-blocks64) for SUN only. * Add mbox1 & mbox2 display for 8048 interrupt if debug-asyc? flag (01) is on. * Fix bug in IBM fcp-luns method for the Controller LUN-0 check, lun0-check. * Check Inquiry Qualifier field of Controller LUN-0 in IBM fcp-luns method. * Add more IOCB debugging, Add Erase Response-Queue in mapmem. Had stale data. * Add more debugging for IOCBs, dma-map-in/out, & wait-for-interrupts.
Version 3.05 * Fix set-fc-address issue found with IBM ioinfo. PortID was not getting set. * Re-structure devicepresent.fth. Add set-phandle to set obp-target & obp-portid * Fix multiple close issue found with IBM ioinfo utility.
Version 3.04 * Add alloc-sec-buf & free-sec-buf words with debugging messages. * Add "ibm,write-supported" property to disk child node, as per IBM's request. * Removed VPD validation from validate-nvram due to bug in update utilities. * Fix enab-nvr-acc to alloc sec-buf & add disab-nvr-acc for BOFM word.
3.03 * Added console messages when validate-nvram finds corruption & copies a sector. * Change validate-nvram to check both FC ports on Dual-port CNAs at probe time. * Fix init-flt-offsets to mask FLT attributes. Now it finds FW & Feature-key. * Added restart-mpi after the beacon test finishes to reset LED functionality. * Add NVRAM backup Sector. Add validate-nvram at probe time to fix corruption.
3.02 Initial release.
2. Known Issues
None
3. Notices
Information furnished in this document is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are only for illustrative purposes. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
4. Contacting Support
For further assisance, contact QLogic Technical Support at: http://support.qlogic.com
Trademarks
Accelera, Accelerating Cluster Performance, InfiniCon Systems, InfiniNIC, InfiniPath, InfiniView, QLA, QLogic, the QLogic logo, ReadyPath, SANdoctor, SANsurfer, and SilverStorm are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.
(c) Copyright 2013. All rights reserved worldwide. QLogic, the QLogic
This software license applies only to QLogic customers. QLogic Corporation. All rights reserved. Release Notes
Table of Contents
1. Version 2. Changes 3. Bug Fixes 4. Known Issues 5. History 6. Additional Information 7. Trademarks 8. Notices 9. Contacting Support
1. Version
These release notes describe the changes, fixes, known issues, and release details that apply to UEFI PXE UNDI driver version 1.10 for the x64 UEFI platform.
2. Changes
3. Bug Fixes
Fix Windows boot when Qlogic adapter mixed together.
4. Known Issues
None
5. History 1.09 - Fix Windows boot hang isssuen when there are multiple adapters. 1.08 - Check RM bit and clean it if it is set. Fix efi driver coundn't login issue if rebooting Sles system from promt. 1.07 - Fix system hang issue whem MPI enables BMC internal traffic.
1.06 - Add Hii support and fix controller name display.
1.04 - When there is an error during bofm implement, the manufacture mac address will be recoved. Add Wc and Bc support.
1.02 - 5/14/09
* Cleared routing table entries before function reset.
1.01 - 4/29/09
* Fixed Bofm support hang system issue.
1.00 - 4/27/09
* Initial release.
6. Additional Information
None
7. Trademarks
QLogic, the QLogic logo, QLA, SANbox, and SANsurfer are registered trademarks of QLogic Corporation.
SANtrack and SAN Express are trademarks of QLogic Corporation.
All other brand and product names are trademarks or registered trademarks of their respective owners.
8. Notices
Information furnished in this document is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are only for illustrative purposes. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
9. Contacting Support
Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance. QLogic Technical Support can be reached by the following methods:
(c) Copyright 2009. All rights reserved worldwide. QLogic, the QLogic logo, and the Powered by QLogic logo are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.
PXE Option ROM for QLogic 10 GbE CNA Release Notes
This software license applies only to QLogic customers. QLogic Corporation. All rights reserved. Release Notes
Table of Contents
1. Change History 2. Known Issues 3. Notices 4. Contacting Support
1. Change History
1.07 - 10/13/09 * Closed ER68817: PXE code produces this log : ql_CloseAdapter( ): Completion pending, * Add display port number when link is down * return error when link is down * Add workaround in base code for tftpd32 error * MPI reset
1.04 - 7/20/09 * Reduce the code size * Add WC/BC for nic parameter and vpd * Use subdevice id for INT18/BEV
1.03 - 5/14/09 * Cleared route table opon exit.
1.02 - 5/4/09
* Fixed the double QLogic PXE banner in IBM HS21 blade. * Fixed system hang in HP ML370 G5 system.
1.01 - 4/29/09
* Added BOFM support (PCI 3.0).
1.00 - 4/27/09
* Initial release.
2. KNOWN Issues
None
3. Notices
Information furnished in this document is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are only for illustrative purposes. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
4. Contacting Support
For further assisance, contact QLogic Technical Support at: http://support.qlogic.com
Trademarks
Accelera, Accelerating Cluster Performance, InfiniCon Systems, InfiniNIC, InfiniPath, InfiniView, QLA, QLogic, the QLogic logo, ReadyPath, SANdoctor, SANsurfer, and SilverStorm are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners.
(c) Copyright 2013. All rights reserved worldwide. QLogic and the QLogic logo are registered trademarks of QLogic Corporation. All other brand and product names are trademarks or registered trademarks of their respective owners. qlgc_fw_cna_qle8142-2_02_06_linux_32-64_chg
============================ R E L E A S E N O T E S ============================
Broadcom Linux bnx2 and 10GigE Virtual Bus Drivers(VBD)
Version 2.2.4g 01/09/2014 Copyright (c) 2004 - 2014 IBM Corporation All rights reserved
NOTE: These driver release information is the original from the vendor. They include multiple driver change histories for multiple Linux Operating Systems. Some drivers may or may not pertain to all Linux Operating Systems but are part of this file for references.
==================================================================================================== Original file from Vendor...
Release Notes Broadcom bnx2 Linux Driver Version 2.2.4g 11/07/2013 Broadcom cnic Linux Driver Version 2.5.18c 10/29/2013
Broadcom Corporation 5300 California Avenue, Irvine, CA 92617
Copyright (c) 2004 - 2013 Broadcom Corporation All rights reserved
bnx2 2.2.4g (Nov 07, 2013) =========================== Fixes ----- 1. Problem: PHY loopback test fails when set to 100Mbps on 5708 Copper.
Cause: Regression caused by enabling auto-MDIX (PHY reg 0x18 shadow 7 bit 9).
Change: Disable it on 5708.
Impact: 5708 only.
bnx2 2.2.4f (Oct 29, 2013) =========================== Fixes ----- 1. Problem: Netqueue didn't get stop and re-initialized properly during reset task, change coalece setting, and self test operations.
Cause: Normal Netqueue stop and re-initialized operations weren't executed while the device went through a full reset.
change: Added proper Netqueue stop/start operations in the above code paths.
Impact: ESX only.
cnic 2.5.18c (Oct 29, 2013) ============================ Enhancements ------------ 1. Change: Add signature to the iSCSI TX doorbell to prevent iscsiuio from getting the wrong value when using older kernel drivers.
Impact: bnx2x iSCSI only.
bnx2 2.2.4e (Oct 23, 2013) ============================ Enhancements ------------ 1. Change: (CQ69514) Enable auto-MDIX when autoneg is disabled by setting copper PHY register 0x18 shadow 7 bit 9.
Impact: All bnx2 copper devices.
2. Change: Display driver version in vmkernel.log during ESX fw dump.
Impact: ESX only.
package 2.78.33 (Sept 23, 2013) =============================== Fixes ----- 1. Problem: Package does not compile on Xen Server 6.2
Cause: kernel compatibility issue.
Change: Added new CFLAGS from bnx2x Makefile for bnx2x_compat.h.
Impact: All distributions. These fixes are only compatible with bnx2x 1.78.56 and newer.
bnx2 2.2.4d (Sept 12, 2013) ============================ Fixes ----- 1. Problem: cnic irq failed to run after esxcli network nic down/up event.
Cause: esxcli network nic down/up event causes bnx2 driver go through bnx2_close and bnx2_open. The sequence of events will re-allocate status block memory and the new status block memory address is not communicated to cnic after bnx2_open.
Impact: bnx2 ESX only.
cnic 2.5.18b (Sept 12, 2013) ============================ Fixes ----- 1. Problem: iSCSI does not work with bnx2x 1.78.52.
Cause: bnx2x doorbell change not compatible with existing iscsiuio.
Change: Pass modified iSCSI CID to iscsiuio for backwards compatibility.
Impact: bnx2x iSCSI.
2. Problem: Panic in cnic after ifdown/ifup bnx2x iSCSI device.
Cause: Accessing uninitialized FCoE EQ. Bug introduced in 2.5.17c which started using bnx2x NO_FCOE macro. cnic did not consistently use NO_FCOE, causing FCoE EQ to be accessed by mistake.
Change: Use NO_FCOE macro consistently in cnic code.
Impact: FCoE.
bnx2 2.2.4c (Aug 30, 2013) ============================ Enhancements ------------ 1. Change: Fix compile errors see on ESX * struct chip_core_dmp definition conflicts with bnx2x, scoped this struct to have a bnx2 prefix * Compiled FW dump for ESX5.5
Impact: bnx2 ESX only.
cnic 2.5.17c (Aug 30, 2013) ============================ Fixes ----- 1. Problem: cnic crash when shutting down 57811 device.
Cause: 57811 Chip ID not reconized by cnic.
Change: Re-structured code to use common bnx2x macros for Chip ID, port ID, pfid.
Impact: iSCSI and FCoE on all bnx2x devices.
bnx2 2.2.4b (Aug 12, 2013) ============================ Fixes ----- 1. Problem: CQ70286 IOVP: PSOD while executing NIC up/down command using esxcli.
Cause: New bnx2_free_irq() also disable MSIX/MSI on the device during bnx2_close. When bnx2_open is called, driver attempt to get INTA interrupt instead of MSIX/MSI interrupt.
Change: Don't disable MSIX/MSI on the device upon close.
Impact: ESX only.
2. Problem: WoL does not work during suspend if device is not up.
Cause: WoL setup skipped in bnx2_suspend() if device is not up.
Change: Always setup WoL in bnx2_suspend().
Impact: bnx2 suspend.
Enhancements ------------ 1. Change: Update 5709 firmware to 6.2.1.c to include mechanism to flush the iscsi OOO ring to silence some error messages about stale hardware index.
Impact: iSCSI on these bnx2x devices where the iSCSI license can only be fully determined after firmware is loaded.
2. Change: Changes to match the new 5709 6.2.1.c firmware to flush the iSCSI OOO ring.
Impact: 5709 iSCSI.
bnx2 2.2.3t (July 23, 2013) ============================ Fixes ----- 1. Problem: CQ70262 IVOP: PSOD HeavyIOChangeMTU test on 5709 card.
Cause: During ring size change, bnx2_free_irq() was called without checking reset_irq flag.
Change: Don't call bnx2_free_irq() if reset_irq flag is false.
Impact: ESX only.
2. Problem: (CQ69619) ethtool NVRAM operations fail when device is down.
Cause: Driver checks and prevents NVRAM operations when device is down.
Change: Remove the check. The driver now stays in D0 power state when the device is down and NVRAM operations are possible.
Impact: ethtool -e|-E
cnic 2.5.16j (July 23, 2013) ============================= Fixes ----- 1. Problem: (RHEL BZ 759217) System hangs when attempting iSCSI connections on 57711E.
Cause: iSCSI license changes from supported to unsupported between bnx2x probe and bnx2x open. bnx2i is unaware that the device does not support iSCSI and attempts to do offload which never completes. The recent change to eliminate symbol_get() to obtain bnx2x_cnic_probe() exposed the problem.
Change: Check iSCSI license again during ->drv_register_cnic(). If there is no iSCSI license, skip ->ulp_start().
Impact: iSCSI on these bnx2x devices where the iSCSI license can only be fully determined after firmware is loaded.
bnx2 2.2.3s (June 27, 2013) ============================ Fixes ----- 1. Problem: PCI shutdown function does not work on ESX.
Cause: system_state and SYSTEM_POWER_OFF not defined.
Change: Added compatibility code.
Impact: ESX only.
bnx2 2.2.3r (June 27, 2013) ============================ Enhancements ------------ 1. Change: (CQ68271, 68277) In order to support ethtool NVRAM operations when the device is down, the following changes were made:
- converted to use new WoL and PM kernel APIs - removed power state changes during open and close - added pci shutdown function to setup WoL during shutdown - converted to new style suspend/resume driver APIs
Impact: Everything related to WoL, shutdown, suspend, resume. Because of the significant changes, the system should be rebooted after running "make install" for the new driver. Without reboot, the new driver may not work as it is not aware that the older driver has put the device into D3hot state.
bnx2 2.2.3q (May 24, 2013) ============================ Enhancements ------------ 1. Change: Simplified compatibility code for driver section macros, __devinit, __devexit, etc.
Impact: None.
bnx2 2.2.3p (May 23, 2013) ============================ Fixes ----- 1. Problem: Bootcode firmware may not detect new message from driver. (VMWare reported issue)
Cause: The initial sequence number may not be unique enough.
Change: Read from the firmware mailbox and add one to it as the initial sequence number.
Impact: All devices.
Enhancements ------------ 1. Change: Made changes to compile on the latest 3.x kernels.
Impact: All.
cnic 2.5.16i (May 23, 2013) ============================= Fixes ----- 1. Problem: (CQ69177) MTU change causes PSOD at bnx2x_drv_ctl
Cause: The OOO handler was falsely triggered to handle OOO tx completions even when bnx2x has failed to allocate resources for the OOO ring. This has caused bnx2x to hit a NULL ptr dereference.
Change: Fixed the cnic OOO handler.
Impact: bnx2x iSCSI only.
cnic 2.5.16h (April 30, 2013) ============================= Enhancements ------------ 1. Change: Added max_fcoe_exchanges parameter so that bnx2fc can support multiple FCoE ports on a device.
Impact: FcoE only.
bnx2 2.2.3o (April 30, 2013) ============================ Fixes ----- 1. Problem: (BDKL225) __napi_schedule assertion when bnx2 switch from MSI to INTx.
Cause: NAPI was not disabled before IRQ is freed when switching from msi mode to INTA mode which prevents VMkernel from updating the stale napi->intr_cookie value.
Change: Disabled NAPI before free IRQ and then re-enable NAPI after chip is re-initialized. In addition, enabling of NAPI should always be done after chip_init().
Impact: All.
bnx2 2.2.3n (Mar 11, 2013) ========================== cnic 2.5.16g (Mar 11, 2013) ========================== Fixes ----- 1. Problem: cnic driver does not compile on XEN server.
Cause: Shared bnx2x_compat.h relies on some CFLAGs to compile properly on XEN server.
Cause: Firmware bug and cnic error handling bug for TCP_CLOSE ramrod.
Change: Added check for iscsi completion error when receiving the TCP_CLOSE ramrod completion.
Impact: bnx2x iSCSI only.
bnx2 2.2.3m (Jan 28, 2013) ========================== cnic 2.5.16e (Jan 28, 2013) =========================== Fixes ----- 1. Problem: (CQ67528) cnic/bnx2 crash when both drivers are loaded on some kernels.
Cause: Shared struct bnx2 compiled differently on bnx2 and cnic, causing cnic to reference the wrong field.
Change: Added bnx2_compat0.h to define the common CFLAGs that affect structure sizes for both drivers to include.
Impact: All (if cnic is loaded)
bnx2 2.2.3k (Jan 25, 2013) ========================== Fixes ----- 1. Problem: CNIC driver didn't get started after bnx2_open().
Cause: CNIC driver is stopped when bnx2_close() is invoked. However, there is no equivalent turn on mechanism when bnx2_open() is called. The issue prevent bnx2i to offload iscsi connections during session recovery.
Change: Added equivalent cnic start procedure in bnx2_open().
Impact: ESX only.
cnic 2.5.16d (Jan 25, 2013) =========================== Fixes ----- 1. Problem: (CQ67375) Unable to turn iSCSI TCP delayed ACK on after it's been turned off.
Cause: tcp_flags in cnic's socket structure not cleared between destroy and create calls.
Change: Clear tcp_flags during socket create call.
Impact: iSCSI only.
2. Problem: (CQ67306) iSCSI TCP delayed ACK not working.
Cause: Firmware HSI change.
Change: Adapted to new firmware HSI which is now defining delayed ACK globally for the HBA.
Impact: iSCSI only.
cnic 2.5.16c (Jan 15, 2013) =========================== Fixes ----- 1. Problem: cnic does not compile on SLES11SP2.
Cause: bnx2x_compat.h conflicts with SLES11SP2 header files.
Change: Modilfed Makefile to detect SLES distribution so that the proper CFLAG can be defined for bnx2x_compat.h
Impact: SLES distributions only.
cnic 2.5.16b (Dec 12, 2012) =========================== bnx2 2.2.3j (Dec 12, 2012) ========================== Enhancements ------------ 1. Change: (CQ60429, 66302) Simplify cnic probing by not using symbol_get(). symbol_get() is unreliable as it fails while the network driver is still initializing.
Impact: iSCSI and FCoE (driver loading and unloading).
Cause: Race condition during simultaneous remote reset and local TCP close/reset. This may be a partial fix and additional fixes in other areas/drivers may be necessary to completely address all symptoms.
Change: If remote reset is detected to be in progress during local close/reset, it will wait for outstanding RAMRODs to complete. Without the wait, bnx2i will proceed to destroy the connection while the SRCH_DELETE/TERM_OFFLOAD RAMRODs are still pending.
Impact: bnx2x iSCSI only.
bnx2 2.2.3i (Nov 05, 2012) ========================== Enhancements ------------ 1. Change: (CQ65960) Make minor compatibility changes to support RHEL6.4
Impact: None.
2. Change: Added support for latest 3.x kernels.
Impact: All supported kernels.
cnic 2.5.14c (Nov 05, 2012) ========================== Fixes ----- 1. Problem: (CQ65178) Panic when loading and unloading cnic with bnx2i and bnx2fc.
Cause: The iSCSI EQ does not get reset during cnic init. When we get the first cnic IRQ, the iSCSI EQ index may be non-zero in the status block, causing the cnic driver to dereference NULL pointer.
Change: Added code to clear the iSCSI EQ index in the STORM memory.
Impact: 10G iSCSI.
bnx2 2.2.3h (Oct 16, 2012) ========================== Fixes ----- 1. Problem: Netdump crash when runing with ESX6.0 OS.
Cause: bnx2 poll controller routine is not compatible with ESX6.0.
Change: For ESX6.0, bnx2 will use ESX poll controller for netdump.
Cause: There is race condition where netdev_watchdog() could erroneouly flag tx timeout in a small window when bnx2_netif_stop() disabled tx queue state while carrier is still on.
Change: Carrier must be turned off before netif_tx_disable() is called.
cnic 2.5.12e (Aug 22, 2012) ========================== Fixes ----- 1. Problem: (CQ 65270): bnx2x IRQ assert on 57712 and newer devices that support iSCSI only.
Cause: Not arming IRQ properly when detecting that the device does not support FCoE. Regression from cnic 2.5.12c enhancement #3.
Change: Added function pointer to arm IRQ correctly based on chip type.
Impact: iSCSI and FCoE on all 10G devices.
cnic 2.5.12d (Aug 21, 2012) ========================== Fixes ----- 1. Problem: (CQ 65249): cnic panic on functions that support FCoE only.
Cause: Code accessing iSCSI resources that aren't initialized or allocated on functions that don't support iSCSI.
Change: Check for valid UIO resource before trying to free it. Always initialize iSCSI OOO resources.
Impact: 10G iSCSI and FCoE.
bnx2 2.2.3d (Aug 15, 2012) ========================== Fixes ----- 1. Problem: (CQ 65163): unhandled NETQUEUE messages 16 and 17 seen in vmkernel logs
Cause: Not properly handling unsupported NetQueue ops
Change: Properly handle the NetQueue ops 16 and 17 without printing the warning message
Impact: ESX only
Enhancements ------------ 1. Change: Try to recover from PCI block reset during TX timeout. Red Hat users have reported PCI block resets that could not be recovered during tx timeout.
Impact: None.
2. Change: Added mk_kernel_patch.sh to patch bnx2 driver into kernel tree.
Impact: None.
cnic 2.5.12c (Aug 15, 2012) ========================== Enhancements ------------ 1. Change: Added firmware dump support for ESX6.0.
Impact: ESX6.0.
2. Change: Reduced maximum iSCSI abort delay to 5 seconds
Impact: iSCSI
3. Change: Allocate FCoE or iSCSI resources on a cnic only if the device supports the protocol. This will reduce memory consumption on multi-function devices.
Impact: iSCSI and FCoE
bnx2 2.2.3c (July 09, 2012) ========================== Fixes ----- 1. Problem: Unmapping the wrong DMA address in bnx2_free_tx_skbs() in rare cases.
Cause: Not skipping the last entry in the tx BD ring.
Change: Use the proper macro to get the next BD entry.
Impact: On systems with IOMMUs enabled, the bug can be triggered when doing resets (ifdown, MTU change) during heavy TX traffic.
cnic 2.5.12b (July 03, 2012) ============================= Enhancements ------------ 1. Change: Updated to bnx2x firmware 7.4.8 HSI for TX BDs.
Cause: Bug in cnic when max OOO resource is reached
Change: Initailized packet descriptor to fix the bug.
Impact: iSCSI only.
bnx2 2.2.3b (June 29, 2012) ========================== Fixes ----- 1. Problem: Compile error in RHEL6.x kernel and similar kernels.
Cause: skb_frag_size() compatibility code not detected properly.
Change: Fixed Makefile to detect it from skbuff.h
Impact: None.
bnx2 2.2.2b (June 24, 2012) ========================== Fixes ----- 1. Problem: (CQ63682)PSOD in ESX upon device open.
Cause: NAPI was not disabled properly upon device close. Thus, ASSERT occurs upon reopening device.
Change: Add NAPI disable upon close and add netif_tx_disable for both linux and ESX build.
Impact: bnx2.
2. Problem: Enableing RSS interferes with RX NETQ feature when compiled for ESX build.
Cause: RSS is enabled by default in bnx2. The RSS feature will lead to firmware bypass NETQ code path.
Change: Disable RSS by default when compiled for ESX.
Impact: ESX.
Enhancements ------------ 1. Change: Partial sync-up with upstream driver. Please see Changelog.
Impact: All
cnic 2.5.11c (June 12, 2012) ============================= Fixes ----- 1. Problem: (CQ62298 Partial fix) When running in INTA mode, MTU change does not work. iSCSI/FCoE does not resume after MTU change.
Cause: During mtu change, bnx2x does not know that cnic is no longer handling IRQs.
Change: Added a new flag to let bnx2x know that cnic is no longer handling IRQ during reset.
Impact: bnx2x iSCSI and FCoE.
2. Problem: (CQ62937) bnx2x asserts during iSCSI test with corrupted TCP NOP-IN.
Cause: Corrupted NOP-IN falls outside of TCP window, causing FW to go into OOO mode. TCP close with outstanding OOO causes problem and the close does not complete.
Change: FW change to return an error in this case and cnic driver change to handle this error by proceeding to clean up the connection.
Impact: bnx2x iSCSI.
cnic 2.5.11b (April 30, 2012) ============================= Fixes ----- 1. Problem: (CQ62298 Partial fix) Fix for CQ62026 in cnic 2.5.9d introduced a regression of clearing the CNIC_UP flag before all CIDs have been deleted. The regression is causing warning messges that some CIDs have not been deleted. After fixing this, we're still encountering further bnx2x error messages in the INTA code path.
Change: Wait for all CIDs to be deleted before clearing CNIC_UP flag.
Impact: iSCSI and FCoE on all bnx2x devices.
bnx2 2.2.1l (April 18, 2012) ============================ Fixes ----- 1. Problem: PSOD on ESX because of inconsistant NetQueue state when the NetQueues are allocated/freed out of order
Cause: The forced freeing of the NetQueue before the NetQueue allocation can cause the incorrect NetQueue to be freed and marked incorrectly.
Change: Remove the freeing of the NetQueue in the allocation path and allow the load balancer to control the error path when NetQueue's could not be allocated/freed.
Impact: ESX only.
cnic 2.5.10c (April 18, 2012) ============================= Enhancements ------------ 1. Change: Added iface_num parameter to cm_create() and iscsi_nl_send_msg()to support bnx2i 2.7.2.2b.
Impact: iSCSI only.
bnx2 2.2.1k (April 04, 2012) ============================ Enhancements ------------ 1. Change: Reduced code size of FTQ dump during tx_timeout.
Impact: None.
cnic 2.5.10b (April 04, 2012) ============================= Enhancements ------------ 1. Change: Added PCI pass through support for bnx2x E2/E3 devices.
Cause: cp->ctx_tbl is NULL during cnic_ctl() call with COMPLETION_CMD.
Change: cnic is registered with the L2 drivers before we allocate the cp->ctx_tbl so it is possible to get called while cp->ctx_tbl is NULL. Added check for CNIC_UP flag before proceeding to dereference cp->ctx_tbl. This together with the RCU code will completely fix the problem.
Cause: Middle-box test corrupts packets and causes iSCSI fw to generate 0x4 (NIC_ERR) completion code. This conflicts with new logic that uses NIC_ERR to convey parity error.
Change: Redefined parity error completion code to be 0x81 for L4, iSCSI, and FCoE.
Impact: FCoE and iSCSI.
bnx2 2.2.1g (Feb 28, 2012) ========================== Fixes ----- 1. Problem: Calling of bnx2_vlan_rx_kill_vid() is not rtnl_lock protected. Change: hold rtnl_lock when execute this routine under ESX4.0 and ESX4.1. Impact: ESX4.0/4.1 only.
bnx2 2.2.1f (Feb 8, 2012) ========================== Fixes ----- 1. Problem: (CQ61327) Unable to pass traffic on RHEL5.x
Cause: bp->num_rx_rings not initialized due to backport errors. This was introduced in 2.2.1e when adding ethtool -l|L support.
Change: Initialized bp->num_rx_rings to 1 on these older kernels.
Impact: RHEL5 and SLES10 only.
cnic 2.5.8f (Feb 06, 2012) ========================== Enhancements ------------ 1. Change: Added VLAN update from iscsiuio. This allows VLAN to be specified in iface.
Impact: iSCSI only.
cnic 2.5.8e (Jan 24, 2012) ========================== Enhancements ------------ 1. Change: Enhanced FCoE parity recovery by sending immediate FW_DESTROY completion with error during parity error recovery.
Impact: FCoE only.
bnx2 2.2.1e (Jan 24, 2012) ========================== Enhancements ------------ 1. Change: Added support for ethtool -[l|L]. Please refer to README.TXT for details.
Impact: 5709 with support for MSIX only.
cnic 2.5.8d (Jan 19, 2012) ========================== Enhancements ------------ 1. Change: Enhanced FCoE driver registration to provide FCoE capabilities to bnx2x driver.
Impact: Systems with Management support of these features. These changes were made to match bnx2x 1.72.07.
2. Change: (CQ60867) Backed out earlier changes related to this CQ. genksyms checksums are based on structure names and type names, so the scheme of using an identical structure with a different name will not work.
Impact: None.
cnic 2.5.8c (Jan 10, 2012) ========================== 1. Problem: (CQ60744) Lose connection to FCoE targets after parity error recovery.
Cause: (Partial) DISABLE_CONN SPQ message does not complete, causing delaying waiting for bnx2fc to timeout.
Change: Added immediate KCQ error completion for FCOE_DISABLE_CONN. when SPQ fails.
Cause: If a TCP connection fails due to parity error, termination sequence does not follow the expedited error recovery path. This causes unnecessary delay during parity error recovery.
Change: Set the HW_ERR bit when TCP connection fails due to SPQ error. Termination will then follow the expedited error recovery path.
Impact: iSCSI on bnx2x.
3. Problem: (CQ60867) Module versioning warning when installing cnic driver on SLES11SP2 without matching bnx2i/bnx2fc.
Cause: cnic_register_driver() stub in cnic.c does not have cnic_ulp_ops structure that matches inbox bnx2i/bnx2fc.
Change: Added dummy cnic_ulp_ops that match RHEL6.2 and SLES11SP2 structures.
Impact: None.
bnx2 2.2.1d (Jan 10, 2012) ========================== Fixes ----- 1. Problem: PSOD seen in TX handling in either bnx2_tx_int() or bnx2_start_xmit() routines
Cause: Memory re-ordering is occuring so that the TX BD is not updated before the ringing of the TX doorbell.
Change: On ESX the wmb() macro is defined to only as a compiler barrier. Redfine the wmb() macro to properly synchronize memory using the sfence instruction.
Impact: ESX only.
cnic 2.5.8b (Jan 05, 2012) ========================== Enhancements ------------ 1. Change: Added CNIC_CTL_FCOE_ENHANCED_STATS_CMD and CNIC_CTL_FCOE_CAPABILITIES_GET_CMD as stubs.
Cause: SPQ errors during parity error recovery was not propagated to L4 and ULP, causing unnecessary long timeouts.
Change: Added immediate KCQ error completion for L4 and iSCSI kwqes if SPQ fails.
Impact: iSCSI on bnx2x.
bnx2 2.2.1c (Dec 21, 2011) ========================== Fixes ----- 1. Problem: (CQ60281) BNX2 hang on ESX 4.1 when changing tx ring size with Ethtool.
Cause: BNX2 set_ringparam() ethtool ops callback attempts to hold rtnl_lock while vmlinux has already held this lock when when invoking this callback. This leads to deadlock situation and driver will hang forever.
Change: Make sure all ethtool ops callbacks don't hold rtnl_lock.
Impact: ESX only.
2. Problem: (BDKL87) PSOD in bnx2 start_xmit() path when stressing with change ring size script on ESX 4.1u2.
Cause: When using ESX4.0/4.1u0-u2, the vmkernel doesn't not check tx queue state properly in certain race condition. This can lead to bnx2 start_xmit() to deference NULL tx buffer.
Change: check tx queue state before proceed with stat_xmit().
Impact: ESX4.0/4.1u0-u2.
cnic 2.5.7h (Dec 08, 2011) ========================== Enhancements ------------ 1. Change: Added iSCSI and FCoE driver status and counters support.
Impact: Systems with Management support of these features.
2. Change: Added upstream patches to sync up with upsteam driver: net: treewide use of RCU_INIT_POINTER net: remove ipv6_addr_copy()
Impact: None.
bnx2 2.2.1b (Dec 08, 2011) ========================== Enhancements ------------ 1. Change: Added several upstream patches to sync up with upsteam driver: net: treewide use of RCU_INIT_POINTER bnx2: fix skb truesize underestimation net: Remove unnecessary driver assignments of ethtool_ringparam fields to zero
Impact: None.
bnx2 2.1.12b (Oct 14, 2011) =========================== Fixes ----- 1. Problem: (CQ59255) iSCSI warning messages appear and performance drops when connected to a lefthand target.
Cause: Packets with invalid TTT generate warnings and exception handling.
Change: Updated to 6.2.3 firmware for 5706 and 6.2.1.b for 5709
Impact: iSCSI
cnic 2.5.7g (Sep 23, 2011) ========================== Enhancements ------------ 1. Change: Added cnic_register_driver()/cnic_unregister_driver stubs so that depmod will not return errors if native bnx2i/bnx2fc drivers have not been updated.
Impact: None.
bnx2 2.1.11e (Sept 19, 2011) =========================== Enhancements ------------ 1. Change: Set the feature, NETIF_F_NO_SCHED, for ESX 5.0 and greater releases only
Impact: ESX only
Fixes ----- 1. Problem: Compile errors on some older kernels.
Cause: Compatibility API pci_is_pcie() requires bool type which may not be defined on older kernels.
Change: Moved bool type compatibility definition above pci_is_pcie().
Impact: None.
bnx2 2.1.11d (Aug 30, 2011) =========================== Enhancements ------------ 1. Change: Integrate Code Review Comments from VMware * Add feature flag to reflect if a device is compliant with network scheduling. * Conditionally move bnx2 drivers to high memory * Remove unused field/code
Impact: ESX only
2. Change: Remove unnecessary read of PCI_CAP_ID_EXP from upstream.
Impact: minor (5709 only).
cnic 2.5.7f (Sep 13, 2011) ========================= Fixes ----- 1. Problem: Duplicate cp local variable in cnic_shutdown_rings().
Cause: Coding error.
Change: Removed duplicate variable.
Impact: None.
cnic 2.5.7e (Aug 8, 2011) ========================= Fixes ----- 1. Problem: (CQ57498) System hangs during bnx2x parity error recovery.
Cause: cnic waits for RAMRODs to complete without timeout. During parity error recovery, all DMAs will stop.
Change: Added timeouts to all RAMRODs.
Impact: iSCSI and FCoE on bnx2x
cnic 2.5.7d (July 28, 2011) =========================== Enhancements ------------ 1. Change: Increased the max number of FCoE sessions to 1024.
Impact: FCoE.
bnx2 v2.1.11c (July 26, 2011) ============================ Enhancements ------------ 1. Change: Upstream sync to use ethtool_cmd_speed API.
Impact: None.
2. Change: Added memory barrier to sync transmit descriptor before updating TX mailbox. We believe that this may fix some very rare panics reported by VMWare.
Impact: bnx2 packet transmit.
cnic 2.5.7c (July 26, 2011) =========================== Fixes ----- 1. Problem: FCOE_DESTROY_FUNC ramrod not completing, causing timeout and OOO cleanup timeout during MTU change.
Cause: FCOE_DESTROY_FUNC was sent before all FCoE CIDs have been deleted.
Change: Wait for all (2 seconds delayed) FCoE CFC_DELETE ramrods to be completed before sending FCOE_DESTROY_FUNC.
Impact: FCoE only.
cnic 2.5.7b (July 19, 2011) =========================== Enhancements ------------ 1. Change: Re-instated vlan_id in ->indicate_netevent(). It is needed by bnx2fc to handle NETDEV_UNREGISTER on VLAN devices.
Impact: bnx2fc.
2. Change: Allocate FCoE CID space only on E2+ devices.
Impact: None.
bnx2 v2.1.11b (July 19, 2011) ============================ Enhancements ------------ 1. Change: Added tx_timeout error handling and made it common with VMWare code.
Impact: bnx2 NETDEV WATCHDOG error handling
2. Change: Fix compile errors on the latest net-next upstream kernel.
bnx2 v2.1.10d (July 12, 2011) cnic 2.5.6c (July 12, 2011) ========================================================= Fixes ----- 1. Problem: Not compiling on 3.0.0 kernel.
Cause: Makefile not recognizing the 3.0.x kernel
Change: Modified Makefile and sync'ed with upstream drivers.
Impact: None.
bnx2 v2.1.10c (July 1, 2011) ============================ Fixes ----- 1. Problem: Not compiling on older kernels (such as RHEL5.4) and newer kernels (such as 2.6.36)
Cause: Problems with compatibility code.
Change: Fixed compatibility code.
Impact: None.
bnx2 v2.1.10b (June 30, 2011) ============================ Enhancements ------------ 1. Change: Added more complete MCP dump during error conditions.
Impact: None.
2. Change: Modified driver messages slightly to match upstream format (by using netdev_printk, netdev_err, etc).
Impact: None.
Fixes ----- 1. Problem: Not reading iSCSI license on 570x devices reliably.
Cause: We were reading from the CP scratch pad before the CP firmware is loaded.
Change: Read from MCP shmem location instead.
Impact: 1G iSCSI on bnx2 devices.
cnic 2.5.6b (June 30, 2011) ============================ 1. Problem: (CQ56522, CQ56259) Unable to connect to iSCSI target, bnx2x firmware assert during iSCSI connection
Cause: iSCSI L2 ring CID has been changed in bnx2x 1.70.14. uIP is using a hardcoded value of 0x11.
Change: cnic now passes the CID to uIP.
Impact: iSCSI on bnx2x devices.
2. Problem: (CQ56230) Cannot compile on some 32-bit systems.
Cause: Passing 64-bit NULL pointer as 32-bit 0 dma_addr_t value.
Change: Use 0 instead of NULL for dma_addr_t values.
Impact: None.
cnic 2.5.5b (June 22, 2011) ============================ Enhancements ------------ 1. Change: Added WWN info to cnic_eth_dev. This is a temporary solution until ndo_fcoe_get_wwn() is implemented.
Impact: None.
bnx2 v2.1.9b (June 22, 2011) ============================ Enhancements ------------ 1. Change: Added del_timer_sync() in bnx2_remove_one() from upstream commit 8333a46ad3877485e4d67ef499c6dda36bfd1f9a. See ChangeLog for details.
Impact: None.
bnx2 v2.1.8c (June 16, 2011) ============================ Enhancements ------------ 1. Change: In ESX, bnx2 will setup int mode during .probe time. However, the dev->name will be finalized only when pci_announce_device is done. So, we assign irq->name in bnx2_request_irq instead of in bnx2_setup_int_mode.
Impact: ESX only.
cnic 2.5.4b (June 1, 2011) ============================ Fixes ----- 1. Problem: (CQ55915) iSCSI does not connect on 57800 in 4-port mode.
Cause: cl_qzone_id was wrong on the 3rd and 4th port. uIP also has some problems determining 4-port mode.
Change: Fixed the QZONE_ID macro.
Impact: bnx2x iSCSI.
bnx2 2.1.8b (June 1, 2011) ============================ Fixes ----- 1. Problem: (CQ55422) NCSI firmware version displayed backwards on PPC.
Cause: Endian bug when reading the data from shared memory.
Change: Fixed byte swapping issue.
Impact: None.
2. Problem: bnx2 does not compile on some PPC distros.
Cause: pci_enable_pcie_error_reporting() not properly defined in some distros.
Cause: Added #ifdef to prevent compiling pci_enable_pcie_error_reporting() on PPC since it uses EEH instead of AER.
cnic 2.4.5b (May 16, 2011) ========================== Enhancements ------------ 1. Change: Check CFC delete error code during completion. If it is set, do not reuse the CID. This change is only compatible with bnx2x 1.64.30 or newer.
Cause: TCP reset request may not complete if there is a race with firmware receiving a remote RST.
Change: Added code to handle TCP reset racing with remote RST and TCP close racing with remote FIN.
Impact: iSCSI
cnic 2.4.3b (April 28, 2011) ============================ Fixes ----- 1. Problem: cnic may lose interrupts after processing 64 kcq entries.
Cause: The driver handles a maximum of 64 entries before calling the ulp drivers. If the chip has more entries, the driver does not handle the rest but acknowledges the latest status block index.
Change: Changed the logic to keep looping until all kcq entries are handled.
Impact: iSCSI and FCoE on all devices.
cnic 2.4.2b (April 21, 2011) ============================ Fixes ----- 1. Problem: (CQ54715, CQ54717) XSEMI parity error detected during iSCSI login on 57712 in NPAR mode.
Cause: Statistic counter ID greater than MAX_STAT_COUNTER_ID_E2 in client init data for iSCSI L2 ring.
Change: Check client ID against MAX_STAT_COUNTER_ID_EXX before enabling statistics.
cnic 2.4.1c (April 11, 2011) ============================ Fixes ----- 1. Problem: (CQ49586) iSCSI reboot test fails after a few iterations.
Cause: TCP port 60000 is used every time during boot. During reset, the TCP connection is never terminated so using the same port to connect to the target during reboot will not work.
Change: Added randomization of the first TCP port to use.
Impact: iSCSI.
bnx2 v2.1.6b (April 6, 2011) ============================ Enhancements ------------ 1. Change: Get iSCSI license information to prevent cnic from registering if there is no license. This will make it consistent with 10G behavior.
Impact: iSCSI only.
cnic 2.4.1b (April 6, 2011) =========================== Fixes ----- 1. Problem: (CQ53236) FCoE HBA not functional after reloading bnx2x.
Cause: In some distros, NETDEV_UP can happen immediately after NETDEV_REGISTER while bnx2x module is still in init state. At this time, cnic will not be able to symbol_get() from bnx2x, preventing the cnic from registering.
Change: Check all events, and we should be able to catch NETDEV_CHANGE abd register cnic.
cnic 2.4.0b (Mar 29, 2011) ========================== Enhancements ------------ 1. Change: Updated cnic to with with bnx2x 1.70.x and added support for 578xx devices.
Cause: Race condition between cnic driver and hardware DMA'ing a new status block with new iSCSI events. The bug was introduced when adding FCoE support.
Change: 1. Add proper memory barrier after reading status block. 2. After servicing FCoE EQ, we must loop back and check the iSCSI EQ again because we may have a newer status block index that is read after servicing the iSCSI EQ.
Impact: 57712 iSCSI and FCoE.
bnx2 v2.1.5c (Feb 15, 2011) cnic 2.3.5c (Feb 15, 2011) ====================================================== Enhancements ------------ 1. Change: Updated 5709 firmware to 6.2.1a, with netq fixes and iSCSI performance regression fixes.
Impact: 5709.
bnx2 v2.1.5b (Feb 08, 2011) cnic 2.3.5b (Feb 08, 2011) ====================================================== Fixes ----- 1. Problem: iSCSI does not connect in DCB environment.
Cause: iSCSI packets are tagged with the wrong ethertype.
Change: Added initialization of xstorm's reserved_vlan_type field.
Cause: BNX2_NETQ_HW_OPENED bit was not properly set.
Change: When the NetQueue device is openned properly set the BNX2_NETQ_HW_OPENED bit in the netq_flags field.
Impact: ESX NetQueue
2. Problem: NetQueue could possibly get out of sync with the uppper layers
Cause: The queue cleanup code between the driver and upper layer is not synchronized
Change: Introduce the NetQueue lock to synchronize the cleaning of the queues between the vmkernel and the bnx2 driver.
Impact: ESX NetQueue
3. Problem: iSCSI may not work if multi-function is disabled in NPAR NICs.
Cause: Bug in logic in detecting NPAR mode.
Change: Offload bit should not be checked if iSCSI MAC address is invalid.
Impact: iSCSI on 57712 NPAR NIC.
bnx2 v2.0.22c (Jan 6, 2011) cnic 2.2.12c (Jan 6, 2011) ========================================================= Enhancements ------------ 1. Change: Updated to 6.2.1a firmware for 5709. It has fixes for CQ51953 (ESX netqueue issue) and CQ51894 (iSCSI performance).
Impact: 5709 iSCSI and L2.
bnx2 v2.0.22b (Jan 4, 2011) cnic 2.2.12b (Jan 4, 2011) ========================================================= Enhancements ------------ 1. Change: Send netlink IF_DOWN message during cnic_unregister_device(). This fixes the problem of bnx2i referencing freed hba when we used to send the netlink message during cnic_unregister_driver().
Impact: iSCSI.
2. Change: Upstream fix for memory leak in cnic_alloc_uio_rings() when we cannot allocate all the memory.
Impact: None.
3. Change: Upstream fix to remove flush_scheduled_work() since it is obsolete.
Impact: None.
4. Change: Do not allow iSCSI on bnx2x devices in MF mode. The hardware does not yet support it.
Impact: iSCSI.
Fixes ----- 1. Problem: SPQ RAMROD type field does not consistently contain the function ID.
Change: Fixed in cnic_submit_kwqe_16() for HSI 6.0 and above.
Impact: iSCSI in NPAR mode.
bnx2 v2.0.21b (Dec 21, 2010) cnic 2.2.11b (Dec 21, 2010) ========================================================= Enhancements ------------ 1. Change: Call cm_connect_complete() when an invalid path_response netlink message is received. This will speed up iscsid in disconnecting the connection. This helps to resolve CQ49665.
Cause: Referencing the cp->kcq1 pointer before checking that the device is up.
Change: Fixed logic so that the cp->kcq1 pointer will only be refernced after checking the device is up.
Impact: iSCSI.
Enhancements ------------ 1. Change: Added retry logic in iscsi_nl_send_msg() to retry netlink messages to userspace.
Impact: iSCSI.
bnx2 v2.0.20f (Dec 09, 2010) cnic 2.2.10f (Dec 09, 2010) ========================================================= Fixes ----- 1. Problem: (CQ51544) Unable to connect to iSCSI targets on 57712 NPAR LOMs with NPAR disabled.
Cause: ff:ff:ff:ff:ff:ff iSCSI MAC address was used in this case.
Change: Add code to detect invalid MAC address and use port MAC address instead. That's the only to determine NPAR is disabled.
Impact: 57712 iSCSI.
2. Problem: MTU change in INTA mode crashes occasionally.
Cause: Status block may be accessed if INTA is shared with another device during reset. There is a short period that the status block is freed.
Change: Free IRQ before freeing status block.
Impact: bnx2 MTU change/ring size change.
3. Problem: Heap corruption reported by VMWare.
Cause: list_del() is called after kfree() in OOO code.
Fix: call list_del() before kfree().
Impact: iSCSI OOO.
bnx2 v2.0.20e (Dec 06, 2010) cnic 2.2.10e (Dec 06, 2010) ========================================================= Enhancements ------------ 1. Change: Adjusted hc timeout for EQ to use the T6.0 value of 4. This will match T5.x HC timeout values.
Impact: 10G iSCSI only.
2. Change: Minor changes to match upstream code.
Impact: None.
bnx2 v2.0.20d (Nov 16, 2010) cnic 2.2.10d (Nov 16, 2010) ========================================================= Fixes ----- 1. Problem: VMware NetQueue not working properly on 5709.
Cause: HSI mismatch.
Change: Updated HSI to match T6.0 bnx2 firmware.
Impact: NetQueue on 5709.
Enhancements ------------ 1. Change: Adjusted kernel compatibility code to compile on RHEL5.6.
Impact: bnx2 and cnic.
bnx2 v2.0.20c (Oct 28, 2010) cnic 2.2.10c (Oct 28, 2010) ========================================================= Fixes ----- 1. Problem: NMI occurs during repeated load/unload of bnx2 driver on 5709.
Cause: The 5709 chip's DMA block wasn't stopped properly before reset.
Change: Fixed by clearing DMA_ENABLE in NEW_CORE_CTL register and polling for pending bus transactions to stop.
Impact: 5709.
Enhancements ------------ 1. Change: Update 5706/5708/5709 firmware to 6.2.1.
Impact: All 1G devices.
2. Change: Fixed one circular lock dependency issue with bnx2i when making up call to send iSCSI NL message.
Enhancements ------------ 1. Change: (CQ49858) Support KVM pass-through mode by eliminating config cycles to non-standard PCI registers (PCICFG_MISC_CONFIG, PCICFG_REG_WINDOW*).
Impact: All chips.
bnx2 v2.0.18c (Sep 13, 2010) cnic 2.2.6c (Sep 13, 2010) ========================================================= Fixes ----- 1. Problem: (CQ49832) bnx2 flow control not working
Cause: Mistakenly disabled in firmware in 2.0.17j to fix CQ46393.
Change: Re-enabled RV2P flow control with additional fixes to for a number of odd flow control issues. New firmware versions are 6.0.15 for 5706/5708 and 6.0.17 for 5709.
Impact: 5706/5708/5709.
Enhancements ------------ 1. Change: Added zeroing of the iSCSI L2 ring's RX BD page to help signal ring shutdown to uIP.
Cause: A mismatch was found in the txbd where the hw prod idx did not match the sw prod idx (via the vlan_id field). The problem will show when uIP restarts without cnic reload. Since uIP restarted, it has lost all previous history about the uio ring.
Change: Added cnic_shutdown_rings to the uio_close path so whenever uio_open is called from uIP, the rings will start off fresh.
Impact: 570X/5771X iSCSI.
2. Problem: (CQ49211) Connection via bnx2i path fails in SuSE 11 SP1
Cause: For 5708/09, the previous firmware set did not take the l2 frame header length into account in the placement filter.
Change: Updated to 5706/08 fw 6.0.14 and 5709 fw 6.0.16 which addresses this issue.
Impact: 570X iSCSI.
bnx2 v2.0.17k (Aug 18, 2010) cnic 2.2.5k (Aug 18, 2010) ========================================================= Fixes ----- 1. Problem: iSCSI sessions do not recover when running under heavy stress conditions with the socket layer.
Cause: The NetLink buffer would get congested, so that the response to the PATH_UPDATE back to uIP would not be delivered.
Change: Use CNIC to throttle the number of outstanding PATH_REQ's to uIP, easing the congestion on the Netlink buffer.
Cause: RV2P firmware was set to drop input packets at a rate which is slower than input line rate when the host stops posting buffers. This has caused the rxp ftq to backup which eventually led to the rxp ftq hw to assert PAUSE and flood the network.
Change: RV2P firmware was modified to disable any waiting before dropping the input packet when the host doesn't post buffers.
Cause: cnic_wq destroyed while cnic_delete_task() is still queued in the workqueue.
Change: Call destroy_workqueue() after cnic_release() which waits for the cnic_delete_task() to finish.
Impact: 10G iSCSI.
bnx2 v2.0.17f (July 30, 2010) cnic 2.2.5f (July 30, 2010) ========================================================= Fixes ----- 1. Problem: iSCSI license not read correctly on 57712 in NIC partitioning mode.
Cause: Missing NIC partitioning license logic.
Change: Added NIC partitioning license logic.
Impact: 10G iSCSI.
Enhancements ------------ 1. Change: Updated 5709 firmware to 6.0.13. The new 5709 firmware has additional rx and tx performance improvements.
Impact: 5709.
bnx2 v2.0.17e (July 29, 2010) cnic 2.2.5e (July 29, 2010) ========================================================= Fixes ----- 1. Problem: (CQ49117, CQ49111) Soft locup when unloading bnx2x with cnic and bnx2fc/bnx2i loaded.
Cause: cnic_cm_stop_bnx2x_hw() thread under rtnl_lock() and pci_bus_sem has to wait for cnic_delete_task() to finish the 2-second wait and CFC DELETE of every FCoE or iSCSI connection. There may be work structs scheduled on the common workqueue ahead of cnic_delete_task() that require the same semaphores, leading to the soft lockup.
Change: Use a dedicated workqueue for cnic_delete_task().
Impact: 10G iSCSI and FCoE.
2. Problem: (CQ49113) Compilation error with bnx2x 1.60.30. (CQ48828) lediag fails with cnic loaded.
Cause: license_key structure changed to use all 32-bit fields. This change is to fix CQ48828 (lediag fails with cnic loaded). 16-bit access causes lediag failure.
Change: Made corresponding change to read 32-bit values for the iSCSI license.
Impact: 10G iSCSI.
3. Problem: (CQ49097) cnic panics when loading on 5708.
Cause: The driver uses NULL OOO ring pointers to initialize OOO for 5708.
Change: Skip OOO completely on 5708.
Impact: bnx2 iSCSI.
bnx2 v2.0.17d (July 28, 2010) cnic 2.2.5d (July 28, 2010) ========================================================= Fixes ----- 1. Problem: (CQ49071) Soft lockup during system shutdown after logging in to 10G iSCSI sessions.
Cause: This was introduced in 2.2.5c when fixing CQ49003. flush_scheduled_work() can deadlock because we're holding rtnl_lock and linkwatch_event may be on the workqueue.
Change: Fixed by using flags to wait for the cnic_delete_task() to finish.
Impact: 10G iSCSI.
2. Problem: cnic driver does not load on 5708 devices.
Cause: Bug in driver that skips devices without OOO support.
Change: OOO setup has been changed so that cnic initialization will continue even if OOO fails for whatever reason on all chips.
Impact: iSCSI.
Enhancements ------------ 1. Change: Updated 5708 firmware to 6.0.11 and 5709 firmware to 6.0.12. The new 5709 firmware fixes small packet rx performance issue. Some adiitional fixes for iSCSI and OOO.
Impact: All bnx2 chips.
bnx2 v2.0.17c (July 23, 2010) cnic 2.2.5c (July 23, 2010) ========================================================= Fixes ----- 1. Problem: (CQ49003) Panic in cnic_free_bnx2x_conn_resc() during ifdown with many 10G iSCSI active sessions.
Cause: cancel_work_sync() is not available in RHEL5.x kernels to wait for cnic_delete_task() to finish before freeing the device's data structures (in particular the csk table).
Change: Use flush_scheduled_work() to wait instead.
Cause: UIO device deleted before userspace has closed the device, causing various failures including kernel panic.
Change: Separated UIO structure from cnic_dev structure so that we can wait until UIO is closed before unregister and deleting UIO.
Impact: iSCSI. This change should have possitive impact on ifup/ifdown, MTU change/selftest/hotplug/etc with active iSCSI sessions.
Enhancements ------------ 1. Change: Allocate the actual number of MSI-X vectors instead of always 9. Also, keep trying if the number of vectors is less than the desired number.
Impact: 5709 networking and iSCSI.
bnx2 v2.0.16c (July 12, 2010) cnic 2.2.4c (July 12, 2010) ========================================================= Enhancements ------------ 1. Change: Added VLAN_TAG_PRESENT to distinguish between physical and VLAN netevents in cnic.
Impact: FCoE.
bnx2 v2.0.16b (July 8, 2010) cnic 2.2.4b (July 8, 2010) ========================================================= Fixes ----- 1. Problem: (CQ48753) cnic will not compile with bnx2x 1.60.27.
Cause: IGU symbols not defined without ELINK_DEBUG defined.
Change: Added ELINK_DEBUG.
Impact: None.
2. Problem: (CQ48717) Kernel panic in bnx2x during ifdown with active iSCSI sessions.
Cause: uio_close() is called after the device is already down. bnx2x will crash when we try to shutdown the iSCSI ring.
Change: Shutdown the iSCSI ring even if uio_close() is not called in the shutdown path.
Impact: 10G iSCSI.
Enhancements ------------ 1. Change: Always run in MSI-X mode on 5709.
Impact: 5709.
2. Change: Added wait of 2 seconds when sending PATH_REQ if UIO has not been opened yet. This improves the liklihood of login success during the first login if using older iscsid.
Cause: pci_save_state()/pci_restore_state incompatibility in older kernel. DECLARE_PCI_UNMAP_ADDR() caused dma mapping field to be undefined on kernels not using IOMMU.
Change: Do not use pci_save_state()/pci_restore_state() on older kernels. Use dma_addr_t to declare mapping fields.
Impact: None.
bnx2 v2.0.15j (June 30, 2010) cnic 2.2.3j (June 30, 2010) ========================================================= Fixes ----- 1. Problem: bnx2x firmware asserts if cnic is loaded on 57711E (MF) functions 2 and higher and the device is brought up.
Cause: Statistics for iSCSI ring not implemented, casuing firmware to assert when the iSCSI ring is initialized.
Change: Do not enable statistics if the clien ID is bigger than MAX_STAT_COUNTER_ID.
Impact: bnx2x iSCSI on 57711E.
2. Problem: cnic terminations for iSCSI and FCoE connections may panic or hang during repeated ifdown/ifup.
Cause: Data structures may be freed while cnic is still waiting for the 2 second CFC_DELETE wait time.
Change: Use cancel_work_sync() to wait for the completion of the cnic_delete_task(). Check that the CTX_FL_DELETE_WAIT flag has been set before waiting.
Impact: bnx2x iSCSI and FCoE.
3. Problem: (CQ48642) Compile errors on older kernels.
Cause: VMWARE_ESX_DDK_VERSION not defined in Linux.
Cause: Race condition between bnx2i initiated TCP close and an asynchronous RESET_COMP from firmware.
Change: Re-structured cnic code that handles close, abort, and various completion events to ensure all scenarios are accounted for with no race conditions.
Impact: All iSCSI connection termination scenarios.
Enhancements ------------ 1. Change: Added host iSCSI IP address to the cnic_dev structure so that bnx2i can report it to sysfs. This is needed for iSCSI boot during pivot_root.
Cause: PCI MSIX attributes not defined in kernel .h files.
Change: Added compatibility code.
Impact: None.
bnx2 v2.0.15d (June 2, 2010) cnic 2.2.3d (June 2, 2010) ========================================================= Fixes ----- 1. Problem: (CQ47942) rmmod hangs if the device has been opened and closed more than once.
Cause: netif_napi_add() called once during every ->open(). netif_napi_del() is only called once during rmmod.
Change: Call netif_napi_del() in ->close().
Impact: None.
bnx2 v2.0.15c (May 21, 2010) cnic 2.2.3c (April 21, 2010) ========================================================= Fixes ----- 1. Problem: service iscsid restart on 5709 does not work.
Cause: Not restarting KWQ correctly due to stale context.
Change: Fixed by correctly zeroing KWQ/KCQ/RX context memory.
Impact: bnx2 iSCSI.
2. Problem: iSCSI license not read correctly on 57711E in single function mode.
bnx2 v2.0.15b (May 12, 2010) cnic 2.2.3b (April 12, 2010) ========================================================= Fixes ----- 1. Problem: iSCSI does not work on 57712.
Cause: License checking always disabled on 57712.
Change: Added proper checking for 57712 iSCSI license.
Impact: None.
2. Problem: (CQ47360) Compile errors on older kernels not supporting UIO and latest iSCSI.
Cause: New cnic driver will only compile on kernels newer than 2.6.31 and some selected distros that have the backport.
Change: Makefile changes to compile cnic only on supported kernels.
Impact: None.
Enhancements ------------ 1. Change: Changed bnx2_cnic_probe() to bnx2_cnic_probe2() so that out-of-tree driver componenets will not inter- operate with upstream components. This avoids compatibility problems that often lead to kernel crashes.
Impact: Out-of-tree cnic will not operate with upstream L2 drivers and vice versa.
2. Change: Revert the PRS_REG_NIC_MODE change done in 2.0.11h. Newer bnx2x driver (1.60.18+) do not require this setting.
2. Change: Added VLAN ID to netdev event callback.
Impact: bnx2i.
bnx2 v2.0.13b (April 22, 2010) cnic 2.2.1c (April 30, 2010) ============================================================ Enhancements ------------ Add debug code to dump all KWQE's (RAMROD) posted to 5771x chipset. This feature can be enabled/disabled using module parameter, by default this feature is disabled. Also a exported function is introduced to dump 3 pages worth of KCQE's
bnx2 v2.0.13b (April 22, 2010) cnic 2.2.1b (April 22, 2010) ============================================================ Enhancements ------------ 1. Change: cnic has been updated to be similar to the upstream versions using UIO with added T6.0 iSCSI support for 10G and other bug fixes.
Impact: iSCSI now requires UIO, new bnx2i, and bnx2x 1.60.16+.
bnx2 v2.0.11j (April 22, 2010) cnic 1.10.2j (April 22, 2010) ============================================================ Fixes ----- 1. Problem: (CQ47298) Does not compile with bnx2x 1.60.16.
Cause: cnic_if.h has changed.
Change: Updated code to be compatible with new cnic_if.h.
Impact: None.
bnx2 v2.0.11i (April 15, 2010) cnic 1.10.2i (April 15, 2010) ============================================================ Fixes ----- 1. Problem: (RHBZ 511368) Driver loses one MSI-X vector after many hours of traffic.
Cause: Chip timing out on write cycle to the MSI-X mask bit, causing the unmask operation to be dropped.
Change: Increase GRC timeout in register 0x8cc. (Same fix from 2.0.8e).
Impact: bnx2x MSI-X mode.
2. Problem: (RHBZ 554706) scheduling while atomic warning when bonding and VLANs are used with cnic loaded.
Cause: bond_del_vlans_from_slave() holds bond->lock when calling ndo_vlan_rx_register(). bnx2 calls bnx2_netif_stop() to stop the rx handling while changing the vlgrp. The call also calls bnx2_cnic_stop() which has many sleeping functions.
Change: Do not stop cnic when VLANs are changed. Since there is no reset during VLAN change, there is no need to stop cnic. (Same fix from 2.0.8e).
Impact: VLAN and iSCSI.
3. Problem: (CQ46940) Poor small packet performance on 5709.
Cause: FTQ discards caused by bottlenecks in firmware.
Change: Upgraded to 5.0.0.j15 MIPS firmware for 5709. (Same fix from 2.0.8c)
Impact: 5709.
Enhancements ------------ 1. Change: Improved rx performance by prefetching next entry's descriptor header and SKB.
Impact: All chips.
2. Change: Updated cnic interface to support out-of-order processing. This is needed for bnx2x 1.60.15 but the feature is not available in cnic yet.
bnx2 v2.0.11b (Jan 28, 2010) cnic 1.10.2b (Jan 27, 2010) ======================================================== Enhancements ------------ 1. Change: Saved bnx2 statistics block before MTU change, ring change, etc.
Impact: bnx2 statistics.
bnx2 v2.0.10b (Jan 12, 2010) cnic 1.10.1b (Jan 12, 2010) ======================================================== Enhancements ------------ 1. Change: Improved cnic's MTU change/reset logic to fix multiple problems in VMWare.
Impact: iSCSI.
2. Change: Converted to bnx2x T6.0 HSI.
Impact: bnx2x iSCSI.
bnx2 v2.0.8e (April 13, 2010) cnic 1.9.13b (Dec 16, 2009) ========================================================= Fixes ----- 1. Problem: (RHBZ 511368) Driver loses one MSI-X vector after many hours of traffic.
Cause: Chip timing out on write cycle to the MSI-X mask bit, causing the unmask operation to be dropped.
Change: Increase GRC timeout in register 0x8cc.
Impact: bnx2x MSI-X mode.
2. Problem: (RHBZ 554706) scheduling while atomic warning when bonding and VLANs are used with cnic loaded.
Cause: bond_del_vlans_from_slave() holds bond->lock when calling ndo_vlan_rx_register(). bnx2 calls bnx2_netif_stop() to stop the rx handling while changing the vlgrp. The call also calls bnx2_cnic_stop() which has many sleeping functions.
Change: Do not stop cnic when VLANs are changed. Since there is no reset during VLAN change, there is no need to stop cnic.
Impact: VLAN and iSCSI.
bnx2 v2.0.8d (April 02, 2010) cnic 1.9.13b (Dec 16, 2009) ========================================================= Enhancements ------------ 1. Change: Improved rx performance by prefetching next entry's descriptor header and SKB.
Cause: Stale status block with old KCQ index after restarting hardware.
Change: Added some additional cleanup and initialization steps including zeroing the status block.
Impact: None.
Enhancements ------------ 1. Change: Updated RV2P P1 for 5709 to 5.0.0.j10 to address a flow control issue that can lead to context corruption. Flow control watermarks have also been optimized.
Impact: 5709 flow control.
bnx2 v2.0.6b (Dec 4, 2009) cnic 1.9.11b (Nov 19, 2009) ======================================================= Fixes ----- 1. Problem: (CQ44801) Unable to compile bnx2 on most 2.6 kernels.
Cause: print_mac() kernel compatibility not defined correctly.
Fix: Simple compatibility fix.
Impact: None.
bnx2 v2.0.5b (Dec 4, 2009) cnic 1.9.11b (Nov 19, 2009) ======================================================= Enhancements ------------ 1. Change: Sync'ed up with latest upstream bnx2 driver. Please see ChangeLog for details.
Impact: Yes, Linux and VMWare.
bnx2 v1.9.42b (Dec 1, 2009) ======================================================= Fixes ----- 1. Problem: Compile error against the VMware ESX 4.0 DDK
Cause: vmk_IscsiNetHandle is not defined with the VMware ESX 4.0 DDK
Change: Added compile flag
Impact: None.
Enhancements ------------
1. Change: Add BMAPILNX ioctl to allow for FW upgrade
2. Problem: (CQ42096) iSCSI sessions do not recover after running selftest/ifdown/etc with max sessions connected.
Cause: cnic_lock mutex has circular dependency, causing deadlock when iscsid tries to cleanup connections.
Change: Merged in upstream cnic patches to avoid circular dependency.
Impact: None.
Enhancements ------------ Change: (CQ43088) Changed the firmware version string format.
Impact: None.
bnx2 v1.9.40b (Nov 18, 2009) cnic 1.9.10b (Nov 12, 2009) ======================================================= Fixes ----- 1. Problem: (CQ44528) Kernel runs out of memory after load/unload bnx2.
Cause: RX SKB buffers were not freed.
Change: Fixed the regression introduced by VMWare development.
Impact: None.
2. Problem: (CQ44399) iLAB 5.10 connection establishment test failure.
Cause: Firmware SYN-ACK handling issue.
Change: Updated firmware to 5.0.0.j6 in bnx2_fw.h and 5.0.0.j9 in bnx2_fw2.h.
Impact: iSCSI.
Enhancements ------------ Change: (CQ43088) Added VPD-R V0 firmware version string to ethtool -i.
Impact: None.
bnx2 v1.9.39b (Nov 6, 2009) cnic 1.9.10b (Nov 12, 2009) ======================================================= Fixes ----- 1. Problem: (CQ44470) Kernel panics when bnx2/bnx2x is unloaded with active iSCSI sessions.
Cause: NETDEV_UNREGISTER will cause bcm570x_* transport to be destroyed while sessions may still be active.
Change: Use module referencing to prevent bnx2/bnx2x from unloading. This is a simple interim solution to revert back to the old behavior. In T6.0, we will migrate to the upstream driver architecture and network drivers will be able to be unloaded again.
Impact: None.
Enhancements ------------ Change: Added a short register dump during NETDEV_WATCHDOG.
bnx2 v1.9.35b (Oct 22, 2009) ======================================================= Fixes ----- 1. Problem: If only 1 queue is used on VMware ESX, iSCSI offload would fail.
Cause: The inboxed VMware driver would only use 1 MSI-X vector. Because of this the driver would not setup MSI-X
Change: Always setup MSI-X reguardless of the number of MSI-X vectors used.
Impact: 5709 iSCSI on VMware
bnx2 v1.9.34b (Oct 20, 2009) ======================================================= Fixes ----- 1. Change: Updated xinan firmware to 5.0.0.j8 Nop timeout tuning (VMware PR467194) Added a new data fw heartbeat to work with the new bootcode and also handle older bootcode.
1. Change: Make NetQueue module parameters more explict.
Impact: bnx2 VMware NetQ.
bnx2 v1.9.32b (Oct 8, 2009) cnic v1.9.7c (Oct 8, 2009) ======================================================= Fixes ----- 1. Problem: CNIC unable to handle an unsolicited RESET COMPLETE which would result in a hung session.
Cause: The CNIC driver couldn't handle unexpected SYN.
Change: The CNIC driver will now handle an unsolicited RESET COMPLETE and cleanup properly.
Impact: cnic
Enhancements ------------
1. Change: Allow the default NetQueue options to be controlled through the macro, BNX2_ENABLE_NETQUEUE.
Impact: bnx2 VMware NetQ.
bnx2 v1.9.31b (Oct 6, 2009) ======================================================= Fixes ----- 1. Problem: PSOD would occur when alloc()'ing NetQueue's
Cause: With the removal of the global 'disable_netq' parameters, the NetQueue CID's weren't being mapped in some cases
Change: Always map the NetQueue CID's
Impact: bnx2 VMware ESX NetQueue
bnx2 v1.9.30b (Oct 5, 2009) ======================================================= Fixes ----- 1. Problem: PSOD would occur because of TX timeouts
Cause: The VMware netdev watchdog timer was ran before the reset task got a chance to run on a loaded system.
Change: Elongated the TX timeout value for VMware ESX only to allow for the reset task to run.
Impact: bnx2 VMware ESX
Enhancements ------------
1. Change: Updated vmkernel module parameter, 'force_netq', to allow NetQueue setting to be adjusted per function rather then globally for all functions.
Impact: bnx2 VMware ESX
bnx2 v1.9.29b (Oct 1, 2009) ======================================================= Fixes ----- 1. Change: Updated xinan firmware to 5.0.0.j7 and teton firmware to 5.0.0.j4 which will fix L2 hang due to iSCSI PDU's padding byte extended to another TCP segment
Impact: 5706/5708/5709.
bnx2 v1.9.28b (Sep 25, 2009) ======================================================= Fixes ----- 1. Change: Updated firmware to 5.0.0.j6 which will add the corresponding flow control trip point.
Impact: 5709.
bnx2 v1.9.27b (Sep 24, 2009) cnic v1.9.7b (Sep 24, 2009) ======================================================= Fixes ----- 1. Problem: For the cnic users would see in the kernel logs:
Cause: The function was not taking into account the wrapping of the software and hardware producer indexes.
Change: Recaculate the difference between the index with wrapping taken into account.
Impact: cnic
Enhancements ------------
1. Change: Updated firmware to 5.0.0.j5 which increased the rxpq depth from 32 to 256 to enhance the performance on systems without flow control.
Impact: 5709.
bnx2 v1.9.26c (Sep 17, 2009) ======================================================= Enhancements ------------ 1. Change: Cleanup the VMware NetQueue code. Eliminate unneeded RX flush routine, fix the number of queues to be the same on 1500 and 9000 MTU sized packets.
Impact: bnx2 VMware NetQ.
bnx2 v1.9.26b (Sep 14, 2009) ======================================================= Fixes ----- 1. Problem: VMware PSOD on MTU change
Cause: MSI-X window was remapped to the beginning of the PCI config space. The driver would disable the bar space because the MSI-X window was remapped incorrectly. This would eventually cause a PSOD.
Change: Before the chip reset, the driver would disable MSI-X, after the chip reset, MSI-X is re-enabled.
Cause: If the driver is unable to allocate memory for the buffers, the device is not properly shutdown.
Change: Added logic to shutdown device if unable to allocate buffers and complete the setup of the device.
Impact: bnx2, changing MTU and ring sizes.
Enhancements ------------ 1. Change: Updated firmware to 5.0.0.j3 for better small packet rx performance. Firmware also fixes header digest error during I/O.
Enhancements ------------ 1. Change: If a TX timeout occurs, there could be the possiblity that the chip is hung. By printing chip state into the kernel ring buffer, it will be easier to determine this.
Impact: bnx2 iSCSI.
2. Change: The bnx2 firmware should always be matched with the proper bnx2 driver. The bnx2 firmware version string are now printed. It will be easier to identify the running firmware.
Impact: bnx2
3. Change: When a TX timeout occurs and the chip is reset, the ability to debug the chip further is lost. This is because the chip state information is lost during the reset. The users have a choice to prevent the chip reset.
Impact: bnx2
4. Change: Add a check to see if there was a KCQ overflow was in the bnx2x firmware. Now this check has been moved to the CNIC so that the driver could control the cleanup/recovery.
Impact: bnx2 iSCSI.
bnx2 v1.9.21b (July 16, 2009) ========================================================== Enhancements ------------ 1. Change: Updated firmware to 5.0.0.j2 to fix remote reset problem
Impact: bnx2 iSCSI.
bnx2 v1.9.20b (July 09, 2009), cnic v1.9.3 (July 09, 2009) ========================================================== Fixes ----- 1. Problem: (CQ42534) cnic.c does not compile on older kernels.
Cause: Some iscsi_proto constants not defined in
Change: Added the constant definitions if not already defined.
Impact: None.
Enhancements ------------ 1. Change: Updated firmware to 5.0.0.j to fix TMF releated iSCSI issues.
Cause: cnic driver sets the MSS without knowing the actual MSS option and timestamp option during TCP connection.
Change: Changed driver to set MSS to 0xffff so that firmware can calculate MSS on its own.
Impact: bnx2x iSCSI.
2. Problem: 1G iSCSI fails when initiator and target MTUs don't match and timestamp is enabled.
Cause: Firmware was not adjusting for the 12-byte timestamp option if MSS was reduced by MSS option.
Change Updated firmware to 5.0.0.i
Impact: bnx2 iSCSI.
3. Problem: (CQ42353) Unable to disable TCP timestamp on 10G iSCSI.
Cause: Timestamp was hardcoded to be enabled for 10G.
Change: Update global timestamp option during each TCP connection.
Impact: bnx2x iSCSI.
4. Problem: (CQ42329) bnx2x MC assert during IPv6 login/logout.
Cause: EQ filled with more than 128 L4 kcqes without MSI-X interrupt for 2 seconds. The driver can only buffer 128 L4 kcqes.
Change: Increased L4 kcqe buffer to 256 entries as a temporary solution. Need to understand the delayed interrupt issue.
Impact: None.
bnx2 v1.9.18b (June 25, 2009), cnic v1.9.1 (June 24, 2009) ========================================================== Enhancements ------------ 1. Change: Added FTQDiscard counter to the list of counters being reported. During small packet test, there may be FTQ overflow and this counter is very useful.
Impact: None.
2. Change: Updated firmware to 5.0.0.h to improve small packet L2 performance and to enhance iSCSI TMF handling.
Impact: 5706/5708/5709.
bnx2 v1.9.17b (June 24, 2009), cnic v1.9.1 (June 24, 2009) ========================================== Fixes ----- 1. Problem: Leaking NetQueues if the firmware did not respond in time
Cause: System might be clogged and there is not enough time to process the KCQ
Change: Updated driver/firmware to allow the calling of the free RX queue request before a RX alloc request is issued
Impact: 5709
2. Problem: An offloaded iSCSI connection would get stuck
Cause: Issing an offload request might fail, and this was not handled properly.
Change: Updated driver/firmware to return the proper return code and handle offload connection failures.
Impact: 5706/5708/5709
3. Problem: tasklet_init() is being called on a task that is scheduled
Cause: When the CNIC calls register_device(), that task might already be schedled.
Change: tasklet_disable() is insufficient because the tasklet remains scheduled and stays on the tasklet list, instead tasklet_kill() is now used.
Impact: 5706/5708/5709
bnx2 v1.9.16b (June 10, 2009), cnic v1.9.0 (June 10, 2009) ========================================================== Enhancements ------------ 1. Change: (CQ38228) Use symbol_get() for ipv6 symbols so that the cnic driver will load without necessarily loading ipv6 modules.
Impact: iSCSI over IPv6.
2. Change: Updated 5706/08/09 MIPS firmware to 5.0.0.g.
Impact: 5706/08/09.
3. Change: Backported some dma_mapping_error() checking.
2. Change: In the cnic driver, save the last allocated TCP port during unregistration so that previously used TCP ports will not be immediately re-used.
bnx2 v1.9.13b (May 18, 2009) ========================================== Fixes ----- 1. Problem: Potentially exceeding the NetQueue limit recommendations by VMware which could stress system resources
Cause: When system resources are strained.
Change: There are now limits on the number of NetQueues which the driver will request: When the MTU is 1500 the max number of queues per port is 8 When the MTU is 9000 the max number of queues per port is 4
Impact: NetQueue enabled version of VMware ESX
2. Problem: Getting conflicting NetQueue and iSCSI completions
Cause: When MSI-X is not used on a 5709, NetQueue is still enabled
Change: NetQueue is not disabled is MSI-X is not used.
Impact: NetQueue enabled version of VMware ESX
bnx2 v1.9.12b (May 13, 2009) ========================================== Fixes ----- 1. Problem: Potentially returning a negative number of NetQueues
Cause: When calculating the number of rings, we use the calculation from the number of msi-x vectors returned, The number of NetQueues returned could potentially be negitive if only 1 vector was returned. This is because the driver was subtracting 2 instead of subtracting 1 (for the default queue) from the total number of rings.
Change: Return the proper number of queues not including the default queue.
Impact: NetQueue enabled version of VMware ESX
bnx2 v1.9.11b (May 12, 2009), cnic v1.8.5 (May 13, 2009) ======================================================== Fixes ----- 1. Problem: TCP Delay ACK not working on bnx2x iSCSI
Cause: Disabled in cnic driver.
Change: Fixed csk->tcp_flags definitions and enabled the proper storm bit for delay ACK.
bnx2 v1.9.10b, cnic v1.8.4 (May 11, 2009) ========================================== Fixes ----- 1. Problem: NetQ and iSCSI do not work in Vmware environment.
Cause: 1. cnic driver is overwriting CP and COM mailbox bit values newly defined to support multiple kcqs.
2. Firmware is completing some iSCSI kcqes on the NetQ's kcq.
Change: Fixed cnic driver to only set and clear bit 0 of the CP and COM mailbox.
Firmware has been updated to 5.0.0d. This firmware also supports TCP timestamp option for iSCSI connections.
Impact: 5706/5708/5709 iSCSI, NetQ.
bnx2 v1.9.9b (May 1, 2009) ========================================== Fixes ----- 1. Problem: There is link, but can't pass traffic on ESXi
Cause: Bits in the RX context are being trampled during the renegotiation of the link.
Change: RX context offset 0x6 should only be initialized once during init and not be updated during run-time. Offset 4 contains the BIDX that's mapped to the mailbox.
Impact: VMware with NetQueue
bnx2 v1.9.8b, cnic v1.8.2 (April 27, 2009) ========================================== Enhancements ------------ 1. Change: Updated cnic driver to support 1.50.x HSI as well as the older 1.48.107 HSI. A compile flag will be used to select one or the other.
Impact: iSCSI on bnx2x.
2. Change: Spec file and Makefile changes detect the proper module install directory.
Impact: installation.
bnx2 v1.9.7b, cnic v1.8.1 (April 22, 2009) ========================================== Fixes ----- 1. Problem: Compile error with redfinition of struct kwqe.
Cause: Both the CNIC and bnx2 defined this structure.
Change: Because the bnx2 definition is L2 specific, it was renamed to struct l2_kwqe.
Impact: None.
2. Problem: Add context memory DMA alignment for 57710.
Cause: For the 57710 context memory needs to be 16k aligned. Without this alignment you will see errors when trying to establish more then 5 iSCSI connections on VMware ESX 4.0 U1.
Change: Properly aligned the context memory by allocating a bigger chunk of memory and then finding the proper alignment. This reduces the number of possible connections in half but now we can properly establish more then 5 connections on VMware.
Impact: iSCSI.
bnx2 v1.9.6b (April 17, 2009) ============================= Enhancements ------------ 1. Change: Added NetQueue support for VMware.
Impact: 5709.
bnx2 v1.9.5b (April 17, 2009) ============================= Enhancements ------------ 1. Change: Updated to 5.0.0.a firmware with NetQ support and iSCSI max connection license information. RV2P firmware unchanged: 4.6.16 for 5706, 4.6.15 for 5709.
Impact: All chips.
2. Change: Set USE_INT_PARAM on 5709. This will switch the chip in use "interrupt mode" coalescing after MSI/MSI-X.
Impact: 5709.
3. Change: Included 5706 when doing statistics block DMA workaround.
Impact: 5706.
bnx2 v1.8.8b (March 12, 2009) ============================= Enhancements ------------ 1. Change: Updated to latest 4.6.17 CP firmware for 5709.
Impact: iSCSI licensing on 5709.
bnx2 v1.8.7b, cnic v1.7.8 (March 10, 2009) ========================================== Enhancements ------------ 1. Change: Reverted 5706/5708 firmware to 4.6.16. Low latency interrupt mode does not work on 5706/5708.
Impact: None.
2. Change: VMWare changes to expose max. number of iSCSI connections in the cnic_device structure.
Cause: msi related symbols undefined because CONFIG_PCI_MSI is not enabled on Xen kernels.
Change: Added CONFIG_PCI_MSI around the msi related code.
Impact: None.
2. Problem: (CQ39818) iSCSI targets do not reconnect after running self test.
Cause: Interrupt is disabled by bnx2 before notifying CNIC to clean up and stop. As a result, bnx2i will not receive interrupts when closing the connections if sharing INTA/MSI with network.
Change: Disable interrupt after notifying CNIC to stop.
Impact: iSCSI.
bnx2 v1.8.6b, cnic v1.7.7 (March 2, 2009) ========================================= Enhancements ------------ 1. Change: Updated to new 5706 firmware (4.6.17) and 5709 firmware (4.6.16). New interrupt coalescing mode for improved latency and iSCSI cache line fix on 5709.
Cause: Bug in bnx2_free_rx_mem(). The jumbo page ring memory was freed incorrectly using the wrong local variable as array index.
Change: Fixed bug by using the correct variable as array index.
Impact: Jumbo frames.
2. Problem: (CQ38965) iSCSI connection timeout on bnx2x.
Cause: During CFC Delete RAMROD completion handling, the wrong (older) iSCSI connection ID can sometimes be retrieved using the harware CID. The CID in the mapping table was not cleared after the CID was freed.
Fix: Adding clearing of the CID in the data structure after a CID is freed.
Impact: bnx2x iSCSI.
Enhancements ------------ 1. Change: (CQ38744) Reduced R2TQ memory usage to match new firmware interface (firmware 4.8.9). This reduces the amount of kernel memory substantially for each iSCSI connection on bnx2x.
bnx2 v1.8.2b, cnic v1.7.2 (Nov 25, 2008) ======================================== Fixes ----- 1. Problem: bnx2x iSCSI does not work on functions 2 or above.
Cause: This was caused by multiple problems: a) Status block ID specified by bnx2x was wrong. b) MSI-X vector assigned to CNIC was wrong. c) New method to ack. status block using HC register was not implemented. d) Status block ID in CSTORM status block is always 0, and as a result, the status block ID used to ack. the status block was wrong.
All these problems only affect functions 2 and above.
Change: All problems fixed in bnx2x and cnic.
Impact: bnx2x iSCSI.
bnx2 v1.8.2b, cnic v1.7.1 (Nov 15, 2008) ======================================== Enhancements ------------ 1. Change: Added CNIC support for Multi function bnx2x iSCSI.
Impact: bnx2x iSCSI.
bnx2 v1.8.2b, cnic v1.6.2 (Nov 12, 2008) ======================================== Enhancements ------------ 1. Change: Updated to latest 4.6.13 5709 firmware to fix context corruption with flow control enabled.
Impact: 5709.
2. Change: Added support for 5716S PCI ID.
Impact: None.
Fixes ----- 1. Problem: (CQ35904) Netdump does not work.
Cause: Problem introduced by MSI-X multiqueue. IRQ handlers were changed to take bnx2_napi parameter instead of netdev parameter.
Change: Fixed by passing proper parameter to IRQ handler from netpoll. All IRQ handlers are called when using multiple MSI-X vectors.
Impact: 5709 netpoll.
bnx2 v1.8.1f, cnic v1.6.1 (Nov 5, 2008) ======================================== Fixes ----- 1. Problem: All TSO packets corrupted on 5706/5708.
Cause: Firmware bug zeroing the wrong field in IP header.
Change: Updated to latest 4.6.11 5706/5708 firmware and 4.6.12 5709 Firmware.
Impact: 5706/5708/5709.
2. Problem: bnx2x chip asserts when trying to make iSCSI connection to an unknown IP address.
Cause: When connection fails, the driver sends a command to an unitialized CID.
Change: Added logic to only send deletion commands to initialized CIDs.
Impact: bnx2x iSCSI.
Enhancements ------------ 1. Change: Added support for one single VLAN to a bnx2x iSCSI interface.
Impact: bnx2x iSCSI.
bnx2 v1.8.1e, cnic v1.6.0 (Oct 27, 2008) ======================================== 1. Change: Updated to latest 5709 firmware to fix iSCSI data integrity problem.
Impact: 5709.
bnx2 v1.8.1d, cnic v1.6.0 (Oct 23, 2008) ======================================== Enhancements ------------ 1. Change: Updated to latest bnx2 firmware to fix iSCSI data integrity problem.
Impact: 5706/5708/5709.
2. Change: Updated to the latest bnx2x HSI files.
Impact: bnx2x iSCSI.
bnx2 v1.8.1c, cnic v1.5.9 (Oct 13, 2008) ======================================== Fixes ----- 1. Problem: (CQ37905) Unable to compile on SLES10 SP2.
Cause: DIV_ROUND_UP macro not defined in this kernel.
Change: Added it for compatibility.
Impact: None.
Enhancements ------------ 1. Change: Updated to latest 5709 firmware that fixes an NCSI problem.
Impact: 5709.
2. Change: Handle TCP reset in the middle of TCP close more appropriately.
Impact: iSCSI.
3. Change: Handle iSCSI license checking in the same way as 5708/5709.
Impact: iSCSI on bnx2x.
bnx2 v1.8.1b, cnic v1.5.8 (Oct 13, 2008) ======================================== Fixes ----- 1. Problem: bnx2x iSCSI CIDs may be allocated outside the range of allocated host memory.
Cause: CID range bigger than the amount of allocated host context memory.
Change: Changed to match the CID range with memory range.
Impact: bnx2x iSCSI.
Enhancements ------------ 1. Change: Sync'ed with the latest upstream driver bnx2 1.8.1.
Impact: None.
2. Change: Implemented iSCSI connection license enforcement for bnx2x devices.
Impact: bnx2x iSCSI.
bnx2 v1.8.0j, cnic v1.5.7 (Oct 6, 2008) ======================================== Fixes ----- 1. Problem: (CQ37610) Chip hangs when changing MTU with active iSCSI connections.
Cause: Both cnic and bnx2 drivers setting up the chip at the same time.
Change: Added check so that the register_cnic function will fail if the bnx2 driver is in reset.
Impact: iSCSI.
2. Problem: (CQ37762) Able to unload bnx2/bnx2x drivers while there are active iSCSI connections.
Cause: CNIC driver does not have a reference count on the BNX2/BNX2X drivers.
Change: This became a problem after the register_cnic function was no longer exported. To solve the problem, the CNIC driver will now get an explicit reference during register_cnic.
Impact: iSCSI.
3. Problem: (CQ37429) MMIO access while the chip is in D3hot state.
Cause: The driver does not check if_running state consistently during ethtool operations.
Change: Added proper checks to all ethtool and multicast change functions.
Impact: ethtool operations and multicast operations.
Enhancements ------------ 1. Change: Simplified ipv4 TSO logic in the driver. This was made possible with newer 5708 firmware.
Impact: 5708 TSO and other traffic.
2. Change: ethtool -p now blinks forever. This is the standard behavior in most other net drivers.
Impact: ethtool -p.
bnx2 v1.8.0i, cnic v1.5.5 (Sep 30, 2008) ======================================== Fixes ----- 1. Problem: (CQ36787) iSCSI login/logout commands fail on 5709 after a while.
Cause: Not handling the KWQ completion properly on 5709 in INTA/MSI mode.
Change: Changed to handle KWQ completions by checking the cmd_consumer_index instead of the rx_quick_index15.
Impact: 5709 ISCSI in INTA/MSI mode.
2. Problem: (CQ37497) CNIC driver does not compile on powerpc.
Cause: csum_ipv6_magic() not defined.
Change: Added #include
Impact: None.
v1.8.0g (Sep 24, 2008) ======================== Fixes ----- 1. Problem: (CQ37511) System locks up when loading cnic driver on 2.6.16 kernel.
Cause: symbol_put_addr() in 2.6.16 tries to acquire the same lock twice.
Change: Workaround by using __symbol_put() which does not have the same problem.
Impact: None.
v1.8.0f (Sep 23, 2008) ======================== Fixes ----- 1. Problem: (CQ37405) Kernel panic when performing ifup/ifdown with iSCSI connections on bnx2x devices.
Cause: Sending searcher delete to bnx2x devices when connection was not established (due to Spanning Tree or other reasons).
Change: Check PG offload state before sending searcher delete.
Impact: iSCSI on bnx2x.
v1.8.0e (Sep 22, 2008) ======================== Enhancement ----------- 1. Change: Updated to latest driver firmware 4.6.6 for 5709.
Impact: 5709.
2. Change: Updated cnic so that it will not crash even if using older bnx2/bnx2x drivers without CNIC support. The net driver can also be loaded after cnic and it will still work without crashing.
Impact: iSCSI.
3. Change: (CQ 37381) Updated driver to check Vaux PRESET before allowing WoL. This is needed to support 5709 quad-port boards.
v1.8.0c (Aug 25, 2008) ======================== Fixes ----- 1. Problem: Does not compile on older kernels.
Cause: "__maybe_unused" undefined on older kernels. "num_online_cpus()" undefined on 2.4 kernels.
Change: Added compatibility code to workaround.
Impact: None.
v1.8.0b (Aug 25, 2008) ======================== Enhancement ----------- 1. Change: Updated to latest driver firmware 4.6.2 for 5709.
Impact: 5709.
v1.7.9c (Aug 5, 2008) ======================== Fixes ----- 1. Problem: bnx2 does not compile on older kernels.
Cause: is missing on 2.6.19 and older kernels.
Change: Added compatibility code to check for kernel version before including the file.
Impact: none.
v1.7.9b (Aug 5, 2008) ======================== Enhancements ------------ 1. Change: Added multi-tx ring for 5709. This fetaure is available on 2.6.27 kernel when using MSI-X.
Impact: 5709
2. Change: Added support for 57710 iSCSI in the CNIC driver.
v1.7.7b (July 9, 2008) ======================== Enhancements ------------ 1. Change: Added probe function so that the CNIC driver can get the pci_device pointer earlier before registration.
Impact: iSCSI.
2. Change: Added support for 5716.
Impact: None.
v1.7.6c (June 6, 2008) ======================== Enhancements ------------ 1. Change: Added multi-ring RX support on 5709 using MSI-X. This feature is only available on 2.6.24 and newer kernels running on SMP machines.
Impact: 5709.
2. Change: Added secondary unicast address support. We now support up to 5 unicast addresses. This feature is only available on 2.6.23 and newer kernels.
Impact: All chips.
v1.7.6b.1 (Aug 14, 2008) ======================== Fixes ----- 1. Problem: (CQ36808) VLAN tagged packets received by host stack without the VLAN tag.
Cause: If no VLANs are set up using vconfig, and if the driver configures the chip to strip the VLAN tag, the problem can happen. With IPMI or UMP enabled, the driver is likely to configure the chip to strip the VLAN tag.
Change: Modified the driver to re-insert the VLAN tag when necessary. I.e. when IPMI/UMP is enabled and vconfig has not setup any VLANs.
Impact: All chips receiving VLAN traffic.
v1.7.6b (May 29, 2008) ======================== Fixes ----- 1. Problem: IPv4 TSO generates bad packet when the TSO packet size is 1-MSS.
Cause: Probably firmware does not expect this boundary condition.
Change: Detect this 1-MSS condition in driver and skip the TSO logic. 1-MSS TSO packet will be treated like a regular TX checksum offload packet.
Impact: TSO on all chips.
2. Problem: Cannot disable VLAN stripping even when management firmware is disabled.
Cause: The new logic to check firmware VLAN stripping capability was buggy.
Change: Fixed the code so that VLAN stripping can always be disabled if management firmware is disabled.
Impact: VLAN/management firmware.
v1.7.5d (May 13, 2008) ======================== Enhancements ------------ 1. Change: Incorporated latest firmware 4.4.18. Bug fix is in RV2P.
Impact: All chips.
v1.7.5c (May 7, 2008) ======================== Enhancements ------------ 1. Change: Incorporated latest firmware 4.4.17. Bug fix is in RV2P.
Impact: All chips.
v1.7.5b (May 5, 2008) ======================== Fixes ----- 1. Problem: (CQ35080) Hard lock when running ethtool -s on the device that is in the down state.
Cause: I/O to the device to set link speed in D3-hot state can cause lockup because the chip does not respond to I/O.
Change: ethtool -s will just store the new settings without configuring the new speed. When the device is later brought up, the new speed will be set as part of chip init.
Impact: All chips.
2. Problem: (CQ35075 CQ35042) Various compile errors on SuSE SLES 9 and SLES 10 distro kernels.
Cause: ip_hdr() and __le32/__le32 backported to the distro kernels.
Change: Adjusted compatibility defines.
Impact: None.
Enhancements ------------ 1. Change: Incorporated latest 5709 firmware 4.4.16. Timer context scanning is reduced with this firmware to 500us. With this, the temporary enhancement in 1.7.4c #2 has been removed.
Impact: 5709 iSCSI.
v1.7.4e (April 26, 2008) ======================== Fixes ----- 1. Problem: (CQ34841) 5709 does not link up on some remote PHY systems.
Cause: No initial link interrupt.
Change: Added code to poll for link when remote PHY is present.
Impact: Remote PHY systems.
2. Problem: (CQ34767) Kernel panic on 5709 when using jumbo frames with NCSI traffic.
Cause: RV2P bug causing RX packets to overwrite kernel memory.
Change: Updated to latest RV2P code for 5709 and 5708.
Impact: 5706/5708/5709.
v1.7.4d (April 17, 2008) ======================== Fixes ----- 1. Problem: IPv6 iSCSI does not work.
Cause: Added code in the last version 1.7.3c to check for CONFIG_IPV6 before enabling the IPv6 CNIC support. This failed to check for CONFIG_IPV6_MODULE if IPv6 is configured as module in the kernel configuration.
Change: Changed the checking to CONFIG_IPV6 or CONFIG_IPV6_MODULE.
Impact: None.
v1.7.4c (April 16, 2008) ======================== Fixes ----- 1. Problem: (CQ34814, CQ33984) Driver does not compile on 2.4 kernels.
Cause: __le32 and __be32 not defined in 2.4 kernels.
Change: Defined these as u32 on 2.4 kernels.
Impact: 2.4 kernels.
Enhancements ------------ 1. Change: Incorporated latest 5709 4.4.12 firmware to fix various iSCSI problems.
Impact: 5709.
2. Change: Slowed down the timer block reload time. It was noticed that after the CNIC driver was unloaded, the timer context memory was reloaded in a tight loop by the chip. This issue needs to be properly addressed in the firmware at a future date.
Impact: iSCSI.
v1.7.4b (April 11, 2008) ======================= Enhancements ------------ 1. Change: Incorporated latest 5709 4.4.11 firmware to fix various iSCSI problems.
Impact: 5709.
v1.7.3k (April 9, 2008) ======================= Enhancements ------------ 1. Change: Incorporated latest 5709 4.4.10 firmware to fix various iSCSI problems. CID ranges are now read directly from shared memory.
v1.7.3g (March 10, 2008) ======================= Enhancements ------------ 1. Change: Updated to latest 5709 firmware version 4.4.7.
Impact: 5709.
v1.7.3f (March 10, 2008) ======================= Fixes ----- 1. Problem: CNIC takes a long time to resolve ARP, causing iSCSI to fail.
Cause: NETEVENT_NEIGH_UPDATE event notifier sometimes takes a long time to be called.
Change: This is under investigation. For now, the workaround is to use the existing neighbour entry if it is in NUD_VALID state. Previously, we would only use it if it was in NUD_CONNECTED state.
Impact: iSCSI neighbour resolution.
2. Problem: iSCSI sometimes fails to initialize.
Cause: The KWQ is in full condition and prevents any KWQE to be sent to the firmware. This is caused by the KWQ consumer index in the status block not initializing to 0.
Change: Added workaround to skip the KWQ full condition check when sending the first KWQE. This should be properly fixed in firmware.
Impact: None.
v1.7.3d (February 15, 2008) ============================ Fixes ----- 1. Problem: System hangs with iSCSI traffic.
Cause: Infinite loop in NAPI poll.
Change: Fixed the problem of not comparing the CNIC tag properly when determining whether there is more work in NAPI poll.
Impact: None.
2. Problem: iSCSI does not work on 5709
Cause: Not initializing 5709 properly for iSCSI. The chip_id field was not propagated to the CNIC driver.
Change: Fixed the chip_id field.
Impact: None.
v1.7.3c (February 09, 2008) ============================ Enhancements ------------ 1. Change: Updated 5708 and 5709 firmware to version 4.4.2.
Impact: All devices.
2. Change: Updated RV2P firmware to the latest. This may fix the jumbo frame issue.
Impact: All devices, especially jumbo frames on 5709 Bx.
3. Change: Modified CNIC interface in preparation for 57710 devices.
Impact: iSCSI.
v1.7.2f (February 04, 2008) ============================ Fixes ----- 1. Problem: Temporary workaround for one prototype 5709S mezz. card not working.
Cause: The driver was looking at the wrong shared memory location to identify the card.
Change: Fixed the code to check the correct BNX2_SHARED_HW_CFG_CONFIG location.
2. Change: Added temporary workaround for one prototype 5709S mezz. card. The workaround will be removed once newer cards are available.
Impact: 5709S.
v1.7.1e (January 14, 2008) ============================ Enhancements ------------ 1. Change: Updated 5709 firmware to 4.1.1 for IPv6 iSCSI support.
Impact: 5709.
2. Change: Updated 5708 RXP firmware to 4.1.1.
Impact: 5706/5708.
3. Change: Updated RV2P firmware for 5709.
Impact: 5709.
4. Change: Added IPv6 support to CNIC driver.
Impact: New BNX2I driver must be used with this new CNIC driver.
v1.7.1d.3 (February 7, 2008) ============================ Fixes ----- 1. Problem: 5706S continues to not link down occasionally on some blade systems.
Cause: In some cases, even turning off the tx current does not cause the link to go down.
Change: Link transition can be triggered based on the SYNC_FAILED bit in the AN_DEBUG register when all else fails.
Impact: 5706S.
v1.7.1d.1 (February 1, 2008) ============================ Fixes ----- 1. Problem: 5706S still not linking down occasionally on some blade systems when the switch blade is disconnected.
Cause: Occasionally, all the bits that we check will falsely indicate link up and trigger the parallel detect logic on this blade platform. Once in parallel detect mode with autoneg disabled, the driver will never detect link down.
Change: Disabled parallel detect on this platform by checking PCI sub IDs to identify the device.
Impact: Parallel detect not supported on this vendor device.
v1.7.1d (January 25, 2008) ============================ Fixes ----- 1. Problem: 5706S still not linking down on some blade systems when the switch blade is disconnected.
Cause: This is the same problem that was fixed in 1.7.0b. After switch module is removed, the SYNC_FAILED bit sometimes toggles low, and this causes the parallel detect logic in the driver to trigger and disable autoneg. Disabling autoneg causes false link to come up immediately.
Change: It seems that the RUDI_INVALID bit can be used to prevent the above from happening. Modified parallel detect code to additionally check the RUDI_INVALID bit and trigger only when the bit is cleared.
Impact: Parallel detect logic in 5706S.
v1.7.1c (December 27, 2007) ============================ Fixes ----- 1. Problem: Driver crashes when adding VLAN and bonding.
Cause: Bonding calls driver's VLAN function in interrupt context with lock held. We recently added a VLAN feature in 1.6.8b which requires chip reset when VLANs are added or removed. The reset will call vmalloc/vfree which must not be called in interrupt context.
Change: Reverted the VLAN feature for now. Will workaround it in the future.
Impact: 5709 only. This new VLAN feature is no longer available.
v1.7.1b (December 24, 2007) ============================ Fixes ----- 1. Problem: Driver crashes when using jumbo frames on 5709 A1.
Cause: RV2P firmware problem.
Change: Disabled jumbo page ring on 5709 Ax chips.
Impact: Jumbo receive page rings not supported on 5709 Ax.
2. Problem: CNIC driver prints "Failed waiting for ref count to go to zero" when unloading the driver. This is a minor cosmetic issue.
Cause: Minor bug in driver comparing ref_count to 1 instead of zero during exit.
Change: Fixed the code to check for ref_count == 0.
Impact: None.
v1.7.0b (December 12, 2007) ============================ Fixes ----- 1. Problem: (CQ33032) CPU utilization increases dramatically when TSO is enabled.
Cause: Driver is spending a lot of unnecessary time in TX handling code when TSO is enabled. This regression was introduced when the TX handling code was changed to match the RX handling code. The RX handling code was changed to fix a packet rot problem. When TSO is enabled, the tx index can stop at non-packet boundaries and the code will keep waiting until it gets to the next packet boundary.
Change: Fixed it to handle this condition properly.
Impact: None.
2. Problem: 5706S does not link down in some blade systems.
Cause: Hardware problem.
Change: Added workaround logic to check periodically and force a link down when the PHY reports SYNC status failed. This only works when autoneg is enabled.
Impact: 5706S.
v1.6.8e (December 10, 2007) ============================ Fixes ----- 1. Problem: When using jumbo MTU with large RX ring sizes, system will crash or the driver won't load.
Cause: Bug in driver where the page descriptor array was declared too small.
Change: Fixed the array size.
Impact: None.
2. Problem: CNIC driver won't compile on kernels without CONFIG_PCI_MSI.
Cause: Some code needs to be conditionally compiled only when CONFIG_PCI_MSI is set.
Change: Added #ifdef CONFIG_PCI_MSI where necessary.
Impact: None.
3. Change: Disabled iSCSI on 5709 until next release.
Impact: None.
v1.6.8d (December 07, 2007) ============================ Change: Reverted the 5706S workaround made in 1.6.8c because it was unreliable.
Cause: RV2P firmware incorrectly placed jumbo data into SKB.
Change: New RV2P firmware.
Impact: Jumbo frames on all hardware.
2. Problem: (CQ32817) ethtool loopback test fails. 3. Problem: (CQ32842) Chariot test fails.
Cause: RX buffer size too small to contain MTU-sized frame. This was introduced by the new Jumbo RX logic.
Change: Fixed RX buffer size logic.
Impact: Traffic on all hardware.
4. Problem: (CQ32862) Fails to compile on RH9u9.
Cause: Kernel API skb_fill_page_desc() backported to RH kernel causing duplicate definition.
Change: Adjusted compatibility code.
Impact: None.
5. Problem: (CQ32866) ISCSI driver fails to compile with 1.6.8b.
Cause: print_mac() multiply defined when bnx2.h is included in the bnx2i driver.
Change: Changed print_mac() to static inline.
Impact: None.
6. Problem: 5706S does not link down in some blade systems.
Cause: Hardware problem.
Change: Added workaround logic to check periodically.
Impact: 5706S.
Enhancements ------------ 1. Change: Added flow control logic on 5709.
Impact: 5709.
2. Change: Updated all firmware to 4.0.5.
Impact: All hardware.
v1.6.8b (November 28, 2007) ============================ Enhancements ------------ 1. Change: Added MSIX support for 5709 B0.
Impact: 5709 B0.
2. Change: Added multi-page buffer support for Receive Jumbo frames.
Impact: All chips. This feature is experimental at this point.
3. Change: Allow VLAN tags in receive packets when management firmware is enabled.
Impact: 5709 only. This feature is experimental and requires new boot code and UMP/IPMI code.
4. Change: Updated firmware to 4.0.3.
Impact: All chips.
v1.6.7b (October 16, 2007) ============================ Fixes ----- 1. Problem: (CQ31861) Remote copper PHY does not link up if WoL is enabled.
Cause: bnx2_set_power_state() assumes that only copper devices support WoL and proceeds to configure the copper PHY to 10/100 Mbps. This assumption is no longer valid after Serdes WoL support was added in 1.6.3c.
Change: Fixed the code to take check for Serdes and copper when setting up the PHY for WoL.
v1.6.5b (September 25, 2007) ============================ Fixes ----- 1. Problem: (CQ30086) 5709 A1 does not link up when connected to some Broadcom devices.
Cause: Early DAC wakeup workaround needed for 5709 A1.
Change: Added workaround.
Impact: None.
Enhancements ------------ 1. Change: Added CNIC support for iSCSI.
Cause: Link test and loopback test were not modified to support remote PHY.
Change: Added remote PHY support to link test and changed the code to skip PHY loopback on remote PHY since it's not supported.
Impact: None.
2. Problem: (CQ30625) ethtool speed settings are lost after ifdown.
Cause: The remote PHY settings stored in firmware is not the same as the driver's last setting.
Change: Modified the code to keep the driver's setting unless there's is change in the remote PHY media.
Impact: ethtool -s on remote PHY systems.
Enhancements ------------ 1. Change: Change ethtool's wol setting to NVRAM's default and add support for Serdes WoL if NVRAM supports it.
Impact: ethtool wol's default setting.
v1.6.3b (July 13, 2007) ======================= 1. Problem: Problems reading and writing flash on 5709.
Cause: Hardware changes in 5709.
Change: Rearranged current flash code to properly support 5709.
Impact: Changes will impact flash operations on 5706/5708/5709 devices.
2. Problem: (CQ30516) Management firmware version string disappears on 2nd modprobe of the driver.
Cause: The 2nd modprobe will program the device back to D0 from D3hot. This causes a reset and it will take some time before the management firmware information will be available.
Change: Added a proper wait loop to wait for the firmware information to be deposited in shared memory.
Impact: None.
v1.6.2f (July 3, 2007) ======================= 1. Problem: The fix for CQ29488 in the previous version is problematic and needs to be reverted.
Cause: Adding the netif_carrier_off() call before register_netdev() in bnx2_init_one() can cause problems if register_netdev() fails. netif_carrier_off() can queue a link watch event that can run later. If register_netdev() fails, the netdev structure will be freed and the link watch event may panic when it is scheduled to run.
Change: Moving the netif_carrier_off() to after register_netdev() also will not work as it can cause race conditions with the interrupt handler. So the best thing to do is to revert the earlier fix and not address the CQ29488 issue.
Impact: CQ29488 is not fixed.
v1.6.2e (July 3, 2007) ======================= Fixes: ------ 1. Problem: (CQ29528) Link does not come up using remote PHY (continued).
Cause: ifup script may be using mii-tool to obtain link status, and interfering with remote PHY firmware.
Change: Block mii-tool ioctl access when remote PHY firmware is present.
Impact: None.
2. Problem: (CQ29488) Driver reports link up in ethtool before the interface is brought up.
Cause: The netdevice structure's initial link setting is up and that gets reported directly by ethtool.
Change: Added netif_carrier_off() call in bnx2_init_one().
Impact: None.
v1.6.2d (June 22, 2007) ======================= Fixes: ------ 1. Problem: (CQ29528) Link does not come up using remote PHY.
Cause: The fix in 1.6.2b still has a problem. The copper or Serdes default link setting does not follow the correct port when the port is changed during chip reset.
Change: Fix the code to always refresh the port and link setting during chip reset.
Impact: None.
2. Problem: (CQ30181) Cannot compile on 2.4 kernels.
Cause: USEC_TO_SEC constant is not defined on older kernels.
Change: Added conditional #define for this constant on older kernels.
Impact: None.
Enhancements: ------------- 1. Change: Update 5709 firmware to 3.7.1.
Impact: 5709 devices.
v1.6.2b (June 21, 2007) ======================= Enhancements: ------------- 1. Change: Added management firmware version to ethtool -i.
Impact: None.
Fixes: ------ 1. Problem: (CQ29528) Link does not come up using remote PHY.
Cause: The driver is using the wrong port when setting up the remote PHY link.
Change: Fixed bug to always use the correct requested port or default port when setting remote PHY link.
Impact: None.
2. Problem: (CQ30028) Advertised Autoneg not set in ethtool.
Cause: Remote PHY code is not setting the flag which is for information only.
Change: Added code the set the flag for consistency.
Impact: None.
v1.6.1c (May 22, 2007) ===================== Enhancements: ------------- 1. Change: (CQ28907) Added support for setting copper and fibre speeds.
v1.5.10c (May 4 , 2007) ======================= Fixes: ------ 1. Problem: Extremely low TSO performance when destination has a smaller MSS than the source.
Cause: Packets smaller than MTU are not processed as TSO packets.
Change: Removed the SKB length check when doing TSO.
Impact: None.
v1.5.10b (May 1, 2007) ========================= Enhancements: ------------- 1. Change: Removed Remote PHY until next release.
Impact: No Remote PHY support.
2. Change: Added check for 2.5G capability before enabling 2.5G on 5709S.
Impact: None.
Fixes: ------ 1. Problem: (CQ28438) NETDEV WATCHDOG after OS boot.
Cause: The mailbox queue is halted after the OS reads config. register 0x94.
Change: Set MQ_CONFIG_HALT_DIS in register MQ_CONFIG on 5709 A0 and A1.
Impact: None.
v1.5.9b (April 20, 2007) ======================= Enhancements: ------------- 1. Change: Enhanced remote PHY support for 5708S.
Impact: None.
Fixes: ------ 1. Problem: (CQ29056) Driver does not compile on SLES 10 SP1 kernel.
v1.5.1b (November 15, 2006) =========================== Enhancement: ------------ 1. Change: Added support for 5709.
Impact: None.
v1.4.52c (March 07, 2007) ========================= Enhancement: ------------ 1. Change: Increase maximum receive ring size to 4080. The default is kept the same at 255.
Impact: None.
v1.4.51b (December 21, 2006) ============================ Fixes: ------ 1. Problem: (CQ27802) Cannot enable flow control in some cases.
Cause: In some cases when flow control is forced to on, the driver detects no changes in advertisement, and as a result, will not re-autoneg. Without the link change, flow control settings will not change.
Change: Added some code to setup flow control when no other PHY settings are made. This will ensure that flow control changes will take effect immediately.
Impact: None.
v1.4.50b (December 15, 2006) ============================ Fixes: ------ 1. Problem: (CQ27424) Panic when writing to nvram.
Cause: Bug in driver when an alignment buffer is used
Change: Fixed the bug so that the alignment buffer is freed with the correct pointer.
Impact: None.
v1.4.49b (December 13, 2006) ============================ Fixes: ------ 1. Problem: (CQ27459) Driver reports link down when link is up.
Cause: Hotplug scripts can cause bnx2_open() to be called immediately after bnx2_init_one() calls register_netdev(). The initial link state set after register_netdev() may overwrite the actual link state set by the link handler on SMP systems.
Change: Move all initial state setup code to before calling register_netdev().
Cause: Bug in determining tx ring space when the tx ring is completely full.
Change: Fixed the flawed logic in bnx2_tx_avail().
Impact: None.
2. Problem: (CQ27424) Buffer overflow when writing to nvram.
Cause: Bug in driver when the beginning NVRAM offset is not 4-byte aligned.
Change: Fixed the bug to allocate enough buffer space.
Impact: None.
3. Problem: (CQ27543) Loopback failed if MAC address is changed.
Cause: Driver uses permanent MAC address for loopback which may be different from a locally administered address.
Change: Fixed by alwaysing using the current MAC address in the netdevice structure.
Impact: None.
v1.4.47b (November 02, 2006) =========================== Fixes: ------ 1. Problem: (CQ25922) 5708S does not pass PHY loopback test on some blade servers.
Cause: It takes longer (about 100msec) to link up in some backplane environments when the Serdes is set to PHY loopback mode.
Change: Increase delay loop to up to 1 sec when waiting for link up after PHY loopback. Previous wait time was 100usec.
Impact: None.
v1.4.46b (October 30, 2006) =========================== Fixes: ------ 1. Problem: (CQ25916) Device does not receive packets when configured by the Xen bridge script and when IPMI is enabled.
Cause: Firmware does not forward packets to the host when the device is in promiscuous mode in some cases.
Change: Firmware change and driver change to enable the BNX2_RPM_SORT_USER0_PROM_VLAN bit when going into promiscuous mode.
Impact: None.
v1.4.45b (October 19, 2006) =========================== Enhancement: ------------ 1. Change: Added software parallel detection on 5708S to link at 1000Mbps or 2500Mbps automatically if the link partner is forced at 2500Mbps.
Impact: None.
2. Change: Added 2500Mbps forced speed setting. Setting it requires a future version of ethtool or custom apps.
Impact: None.
3. Change: Port driver to compile on 2.6.19 kernel.
Impact: None.
Fixes: ------ 1. Problem: Driver does not complile on 2.4 kernels.
Cause: TSO symbols not defined in 2.4 kernels.
Change: Added #ifdef for compatibility.
Impact: None.
2. Problem: MSI doesn't work on 5706 when the host bridge is AMD8132.
Cause: Compatibility issue.
Change: Added code to disable MSI when 5706 is on a systems with AMD8132.
Impact: 5706 cannot use MSI on such systems.
v1.4.44b (August 10, 2006) ========================== Fixes: ------ 1. Problem: A rare tx race window exists in the tx path.
Cause: CPU re-ordering can cause the tx queue to be stopped forever when the tx ring is full in a very rare condition. See ChangeLog for more details.
Change: Fixed the race condition with memory barriers. See ChangeLog for more details.
Impact: None.
Enhancement: ------------ 1. Change: Increase default rx ring size to 255 to prevent packet drops under heavy load.
Impact: Higher memory usage.
2. Change: Port driver to run on 2.6.18 kernel.
Impact: None.
v1.4.43b (June 26, 2006) ======================= Enhancement: ------------ 1. Change: (CQ25508) Use DRV_MSG_CODE_UNLOAD_LNK_DN message on 5708 B1 and older chips so that the link will turn off after ifdown.
Impact: None.
v1.4.42b (June 2, 2006) ======================= Fixes: ------ 1. Problem: (CQ22585) WoL cannot be enabled on 5708 B2.
Cause: Hardware limitation in previous 5708 versions required driver to always disable driver WoL on 5708.
Change: With the issue fixed in B2, the driver was changed to allow 5708 B2 and above to support driver WoL.
Impact: None.
2. Problem: (CQ21779) Driver does not report dropped receive packets.
Cause: Packets dropped by firmware are reported in a scratch pad location in memory separate from other counters.
Change: Added code to report this firmware counter.
Impact: None.
Enhancements: ------------- 1. Change: (CQ24690) Allow driver to be compiled for non-running kernels.
Impact: None.
v1.4.41b (May 17, 2006) ======================= Fixes: ------ 1. Problem: Driver writes wrong data to non-buffered flash.
Cause: Bug in driver causing the unchanged portion of the page to be corrupted.
Change: Fixed bug.
Impact: None.
v1.4.40b (April 17, 2006) ========================= Enhancements: ------------- 1. Change: Combine 2 small memory allocations into 1.
Impact: None.
2. Change: Separate tx consumer and producer entries into separate cache lines for better performance.
Impact: None.
3. Change: Compress firmware data to reduce driver size.
Impact: Driver now requires zib_inflate library which should be available on most vendor kernels.
v1.4.39b (Mar. 10, 2006) ======================= Fixes: ------ 1. Problem: (CQ23181) Driver loses track of link changes in some cases.
Cause: In some cases, the status block gets a link change indication that contradicts with the MII link status. This is due to transient link signals during link changes.
Change: Add coalesce_now at the end of link change interrupt to flush out the transient behavior.
Impact: None.
2. Problem: 5708 only supports 40-bit DMA addresses.
Cause: Limitation of the built-in PCIE-to-PCIX bridge.
Change: Add workaround code to make sure all DMA addresses are less than 40 bits.
Impact: Some minor impact on performance on some 64-bits systems. There should be practically no performance impact on i386 and x86_64 systems.
3. Problem: "Copyright" deprecated in RPM spec file.
Change: Changed to "License".
Impact: Should be none on the distributions that we support.
v1.4.38b (Feb. 10, 2006) ======================= Fixes: ------ 1. Problem: Setting rx ring size to 255 causes memory allocation errors.
Cause: Multiple bugs that do not handle the full ring properly.
Change: Fixed all bugs related to full ring handling and changed maximum ring size from 4080 to 1020 after discussion with Dave Miller.
Impact: Maximum rx ring size is now smaller.
2. Problem: Compile warnings and panic on IA64.
Cause: not included.
Change: Added include .
Impact: None.
v1.4.36b (Jan. 19, 2006) ======================= Version number update.
v1.3.36 (Jan. 17, 2006) ======================= Fixes: ------ 1. Problem: (CQ22827) bnx2 does not compile on 2.6.6 and earlier kernels.
Cause: Introduced bug while fixing CQ22666.
Change: Fix compatibility code.
Impact: None.
2. Problem: (CQ22823) bnx2 reports extra .5 at the end of firmware version string.
Change: Skip the last digit in the firmware version string.
Impact: None.
3. Problem: (CQ22585) WoL still does not work on 5708.
Cause: New WoL mechanism introduced in 1.3.34 has a flaw.
Change: Removed the workaround code and disabled WoL support on 5708. During shutdown and suspend, the driver will shutdown the device and WoL will be setup by the bootcode according to the nvram's out-of-box WoL setting.
Impact: 5708 will not support driver-initiated (ethtool-intiated) WoL.
v1.3.35 (Jan. 17, 2006) ======================= Fixes: ------ 1. Problem: (CQ22666) bnx2 driver does not compile on RHEL3 U7.
Cause: if_mii() back-ported to RHEL3 U7.
Change: Adjusted the compatibility code.
Impact: None.
2. Problem: (CQ22718) UMP connection is lost after enabling WoL.
Cause: FORCE LINK was mistakenly set during WoL setup.
Change: Do not set FORCE LINK.
Impact: None.
v1.3.34 (Jan. 13, 2006) ======================= Fixes: ------ 1. Problem: (CQ22585) WoL does not work on 5708.
Cause: Internal bridge not in proper PME state.
Change: Added new firmware message to allow bootcode to help set up WoL.
Impact: None.
Enhancements: ------------- 1. Change: Added compile option to include crc32 function for RH2.4 boot kernels.
Impact: None.
2. Change: Updated TSO firmware to handle ECN.
Impact: None.
v1.3.33 (Dec. 12, 2005) ======================= Enhancements: ------------- 1. Change: Increased firmware hand-shake timeout from 50 msec to 100 msec. Also changed the delay from busy-wait udelay to non-busy-wait msleep.
Impact: None.
2. Change: Added code to read nvram size from shared memory if available. Otherwise, the size will come from the flash table which only gives the smallest size for that type of flash.
Impact: None.
3. Change: Added workaround to issue 2 separate IOs for interrupt acknowledgement. The workaround is only used for INTA (non-MSI) interrupts.
Impact: Slightly higher overhead for INTA interrupts.
v1.3.32 (Dec. 01, 2005) ======================= Enhancements: ------------- 1. Change: Added PHY loopback to the loopback selftest.
2. Change: Enabled customized pre-emphasis and other serdes control settings on 5708S backplane devices. A special PHY register will be programmed according to the NVRAM value.
Impact: None.
3. Change: Modified Makefile to check for the source symbolic link in the kbuild environment.
Impact: None.
4. Change: Improved NAPI poll processing so that all events will be processed before interrupts are re-enabled. This will reduce the number of unnecessary interrupts.
Impact: None.
5. Change: Add support for ETHTOOL_GPERMADDR (from John Linville)
Impact: None.
Fixes: ------ 1. Problem: Bug in irq handler causing extra register read.
Cause: Bug in bnx2_interrupt() reading BNX2_PCICFG_MISC_STATUS register when it is not necessary.
Change: Fixed the logic bug and added prefetch of status block in msi handler.
Impact: None.
v1.3.25 (Aug. 22, 2005) ======================= Fixes: ------ 1. Problem: Ethtool register and memory tests fail on 5708.
Cause: Some code was not merged properly many versions ago.
Change: Merged in properly code.
Impact: None.
Enhancements: ------------- 1. Change: Slow down flash clock speeds
Impact: None.
2. Change: Code re-sync'ed with upstream driver.
Impact: None.
v1.3.24 (Aug. 16, 2005) ======================= Enhancements: ------------- 1. Change: Changed all spin_lock_irqsave locks to spin_lock_bh for better overall system performance. All code requiring spin_lock runs in BH or user context.
Impact: None.
2. Change: Removed atomic operations in the transmit fast path. Code should run a bit faster as atomic operations can be quite slow.
Impact: None.
v1.3.23 (Aug. 10, 2005) ======================= Enhancements: ------------- 1. Change: Added reporting of link speed to firmware.
Impact: None.
2. Change: Added shared memory base look-up.
Impact: None.
3. Change: Possible sparse fixes (from Peter Hagervall) - use C99 struct initializers - make a few arrays and structs static - remove a few uses of literal 0 as NULL pointer - use convenience function instead of cast+dereference in bnx2_ioctl() - remove superfluous casts to u8 * in calls to readl/writel
Impact: None.
4. Change: Updated documentation with the crc32 library requirement and other minor updates.
Impact: None.
v1.3.22 (July 25, 2005) ======================= Enhancements: ------------- 1. Change: Added check for default link speed setting in shared memory. This allows some blade servers that don't support autoneg to default to forced speed to speed up link-up time.
Impact: None.
2. Change: Changed timer code to speed up the timer after serdes autoneg. This speeds up the time for parallel detection when the link partner does not autoneg. After autoneg or parallel detction completes, timer goes back to normal 1 HZ interval. With the new scheme, link should be detected up using parallel detection in less than 0.7 seconds. Autoneg normally completes in 120 msec exchanging base pages and 3 next pages.
Impact: None.
v1.3.21 (July 21, 2005) ======================= Enhancements: ------------- 1. Change: Updated firmware to properly handle TSO packets with ECN bits set.
Impact: None.
2. Change: Updated to latest rxp firmware.
Impact: None.
3. Change: Added check for the 2.5G capability in shared memory.
Impact: None.
4. Change: Expanded nvram support for 5708.
Impact: None.
Fixes: ------ 1. Problem: (CQTO1511) Downing a team of bnx2 adapters causes hang.
Cause: Deadlock when the second adapter's close routine calls flush_scheduled_work() because the linkwatch_event is scheduled on the work queue when the first adapter is closed. The linkwatch_event will try to get the rtnl_lock which is already held by the bnx2_close routine.
Change: Fixed by not calling flush_scheduled_work(). Instead, use a flag to indicate work is pending and wait until the flag is cleared.
Impact: None.
2. Problem: (CQTO1439) ethtool -S on 5708 causes oops.
Cause: A pointer is not initialized if the device is 5708.
Change: Added proper initialization.
Impact: None.
3. Problem: Some error counters are mis-reporting.
Cause: The workaround for the hw errata is not applied properly on the chips with the errata.
Change: Added proper checks for the workaround.
Impact: None.
4. Problem: High BER on 5708 SerDes.
Cause: hardware errata.
Change: Added workaround for 5708 A0 and B0.
Impact: None.
v1.3.19 (May 27, 2005) ======================= Enhancements: ------------- 1. Change: Merged 5708 code with the latest 1.1.19.
Impact: None.
Fixes: ------ 1. Problem: (CQTO1260) 5708S does not link at 1000Mbps when forced. It links at 2500Mbps when connected back-to-back with another 5708S.
Cause: 2.5G bit is still turned on.
Change: Fixed by turning off 2.5G when the speed is forced.
Impact: None.
v1.1.19 (May 26, 2005) ======================= Enhancements: ------------- 1. Change: Made significant changes to merge into the kernel. Among them, consolidate all source files into bnx2.[ch] and bnx2_fw.h, change structure style register definitions to offset based.
Impact: None.
Fixes: ------ 1. Problem: Excessive stack usage.
Cause: Use of local variable array.
Change: Fix excessive stack usage in bnx2_alloc_bad_rbuf() by replacing local variable array with kmalloc array. Also changed function to return error code, and changed some of the callers to check for the return code.
Impact: None.
2. Problem: Bug in receive checksum.
Cause: Software bug.
Change: Fix bug in rx checksum by indicating CHECKSUM_UNNECESSARY only when the hw calculated checksum is 0xffff.
Impact: None.
3. Problem: Excessive busy loop.
Cause: Software bug.
Change: Replaced one excessive udelay of 15msec with msleep since the calling context is always process.
Impact: None.
4. Problem: Need to call flush_scheduled_work() and bnx2_netif_stop().
Cause: Bug in bnx2_close().
Change: Fix bug in bnx2_close() by calling flush_scheduled_work() since we are using a work queue in netdev watchdog. Also added bnx2_netif_stop() call in bnx2_close().
Impact: None.
5. Problem: Some symbols do not have bnx2 prefix and are not static.
Change: Add bnx2_ prefix to some remaining names and mark some remaining names static.
Impact: None.
v1.1.17 (Apr. 7, 2005) ======================= Fixes: ------ 1. Problem: Driver does not compile on 2.6.12 kernel.
Cause: pci_dev->slot_name has been deprecated.
Change: replaced with pci_name.
Impact: None. All kernels supported by bnx2 including 2.4.21-*EL have pci_name defined.
v1.1.16 (Mar. 16, 2005) ======================= Fixes: ------ 1. Problem: (CQTO936 & 1004) Tx carrier and rx_byte_errors reported during normal operations.
Cause: 5706 hardware errata on these 2 statistics counters.
Change: Modified driver to skip these 2 counters.
Impact: These 2 counters will always report 0 and not the true statistics.
v1.1.15 (Mar. 09, 2005) ======================= Enhancements: ------------- 1. Change: Added code to program proper phy settings for jumbo frames on copper and serdes devices.
Impact: None.
2. Change: Changed INTx ISR to handle a valid case where INTx arrives before status block update.
Impact: None.
3. Change: Added a separate ISR for MSI to handle subtle differences between INTx and MSI.
Impact: None.
v1.1.14 (Mar. 03, 2005) ====================== Fixes: ------ 1. Problem: netdump does not work on latest RH3EL errata kernel.
Cause: #define RED_HAT_LINUX_KERNEL removed from kernel include files, causing netdump poll function to be compiled wrong for RH kernels.
Change: Changed Makefile to workaround the problem.
Impact: None.
v1.1.12 (Feb. 25, 2005) ====================== Fixes: ------ 1. Problem: (CQTO1062) Driver allows ethtool to set illegal speed/duplex on fiber cards.
Cause: Missing checks for the case where autoneg is off.
Enhancements: ------------- 1. Change: The code to handle tx queue full condition was redone to properly handle all boundary and race conditions.
Impact: Minimum tx ring size is now MAX_SKB_FRAGS+1.
2. Change: Tx timeout code was changed to work queue context. This allows netif to be shutdown gracefully before chip reset.
Impact: None.
3. Change: Added memory barriers to ISR and NAPI poll for correctness.
Impact: None.
v1.1.8 (Feb. 01, 2005) ====================== Fixes: ------ 1. Problem: (CQTO969) No interupts on a system that does not support MSI.
Cause: On this system, the MSI generated in the MSI test terminates with Master Abort which is a fatal condition for the chip.
Change: A chip reset is added when MSI test fails to bring the chip back to normal operations again (in INTx mode).
Impact: None.
Enhancements: ------------- 1. Change: Removed register 0x84 from the ethtool register test. This is an interrupt control register that should not be touched to prevent unwanted interrupts.
Impact: None.
v1.1.7 (Jan. 28, 2005) ====================== Enhancements: ------------- 1. Change: Added interrupt test when MSI is enabled. If MSI test fails, driver will fallback to INTx mode.
Impact: None.
2. Change: Added test for certain chipsets where MSI is known to fail, and disable MSI unconditionally when such chipsets are found.
Impact: None.
3. Change: Removed support for 1000 Mbps half duplex.
Impact: 1000 Mbps half duplex will no longer work.
v1.1.6 (Jan. 26, 2005) ====================== Fixes: ------ 1. Problem: (CQTO940) MTU size not set properly when device is down.
Cause: bnx2_change_mtu only handled the "up" case.
Change: Simple fix to handle the "down" case as well.
Impact: None
2. Problem: (CQTO926) 5706S does not autoneg properly after the tx cable is pulled.
Cause: If the link partner is autonegotiating, autoneg will fail when the tx cable is pulled. The software will turn off autoneg seeing that the rx cable is still attached with SIGNAL_DETECT. When the tx cable is re-attached, autoneg is still off and the link partner will not establish link.
Change: Added code to poll another PHY register to check if configs are received when autoneg is disabled.
Impact: None
Enhancements: ------------- 1. Change: Added OEM product name strings.
Impact: None.
v1.1.5 (Jan. 25, 2005) ====================== Fixes: ------ 1. Problem: PCI-X bus speed may not be detected correctly by the driver, causing failure because certain register settings are done based on bus speed.
Cause: hardware problem.
Change: Use a different register to detect PCI-X speed.
Impact: None.
v1.1.4 (Jan. 17, 2005) ====================== Fixes: ------ 1. Problem: 5706S does not reliably detect link up or down.
Cause: hardware problem.
Change: Enabled hardware workaround which is effective in A2 and newer chips only.
Impact: None.
v1.1.3 (Jan. 13, 2005) ====================== Fixes: ------ 1. Problem: netdump does not work.
Cause: poll_controller routine does not work in NAPI mode.
Change: Fixed poll_controller routine for NAPI mode.
Impact: None.
Enhancements: ------------- 1. Change: Added the new mmiowb macro which is used mainly in NUMA machines to guarantee PCI ordering.
Impact: None.
2. Change: Added OEM product name strings.
Impact: None.
3. Change: Changed ONE_TDMA workaround on systems with P64H bridge to PING_PONG_DMA on all systems using PCI.
Impact: Better performance and better compatibility on all PCI systems.
4. Change: Added "disable_msi" parameter to allow disabling MSI.
Impact: None.
5. Change: Reduced default tx coalescing parameters for better tx only performance such as ttcp.
Impact: None.
6. Change: Changed NIC detection console message to display more information.
Impact: None.
7. Change: Cleaned up some Linux .h files that are not needed.
Impact: None.
8. Change: Cleaned up the nvram routines.
Impact: None.
v1.1.2 (Nov. 11, 2004) ====================== Fixes: ------ 1. Problem: Unable to load the driver on more than 2 or 3 devices.
Cause: Default register space is too big. System fails to map the register space on the 3rd or 4th device.
Change: Changed driver to map a smaller register space as the higher registers are not needed for standard operations.
Impact: None.
v1.1.1 (Nov. 9, 2004) ====================== Fixes: ------ 1. Problem: (CQTO656) One remaining ethtool parameter can be set out of range.
Cause: Wrong upper bounds in code.
Change: Fixed upper bound.
Impact: None.
1. Problem: 5706 A1 cannot be run on a PCI bus.
Cause: Hardware errata.
Change: Added workaround to detect 5706 A1 on PCI bus and abort.
Impact: Driver will not load 5706 A1 on PCI bus.
v1.1.0 (Oct. 29, 2004) ====================== Fixes: ------ 1. Problem: (CQTO663) No link on fiber NIC set to autoneg when the link partner is set to forced speed.
Cause: No code to handle this case.
Change: Added code to check SIGNAL DETECT when autoneg fails, and turn off autoneg when appropriate. Also added code to force a link down when speed settings are changed.
Impact: None.
2. Problem: (CQTO649) ifconfig up/down can cause system to hang on 2.6 kernels using mmconfig.
Cause: Dummy read in the kernel's pci_mmcfg_write routine may cause system to hang during D3hot -> D0 transition. The PLL may lose lock during the internal D0 transition chip reset and cause the dummy read to hang.
Change: The PLL problem will be fixed in A2. Meanwhile, the driver is changed to go into D3hot only if wol is enabled.
Impact: Minor impact in increased power consumption when the driver is shutdown with wol disabled.
3. Change: Changed to use pci_get_device as pci_find_device will be deprecated soon.
Impact: None.
4. Problem: (CQTO656) Some ethtool parameters can be set out of range.
Cause: Wrong upper bounds in code or documentation.
Change: Fixed code and documentation.
Impact: None.
v1.0.15 (Oct. 15, 2004) ====================== Fixes: ------ 1. Problem: (CQTO644) Data corruption when sending FTP traffic on Dell Precision 530MT.
Cause: PCI bridge errata.
Change: Added code to enable ONE_TDMA workaround when P64H PCI bridge is detected.
Impact: Slower tx performance on systems using P64H bridge.
2. Problem: (CQTO643) Driver allows MTU to be set up to 9004.
Cause: Driver used the wrong upper bound limit.
Change: Fixed the upper bound.
Impact: None.
3. Problem: Driver does not support forced speed on 5706S.
Cause: Missing software logic.
Change: Added code to support forced 1000 Full and Half duplex.
Impact: None.
4. Change: Added workaround to disable PERR generation on 5706 A1 when it is in PCI 64-bit slot.
Impact: None.
v1.0.14 (Oct. 05, 2004) ====================== Fixes: ------ 1. Problem: Driver load/unload hangs on some machines.
Cause: Transition delay required during D3hot -> D0 transition.
Change: Added necessary delay.
Impact: None.
v1.0.12 (Oct. 04, 2004) ====================== Fixes: ------ 1. Problem: (CQTO609) New flow control parameter does not take effect until ifdown/ifup or link down/up.
Cause: New flow control settings are only configured during link up. The driver did not check flow control advertisement changes and therefore no re-negotiation and no link down.
Change: Fixed logic so that link will always go down whenever there is a change a flow control advertisement.
Impact: None.
2. Problem: (CQTO612) VLAN packet reception not working.
Cause: VLAN #define not setup properly.
Change: Fixed #define for VLAN.
Impact: None.
3. Problem: (CQTO628) WoL not functioning correctly.
Cause: Multiple problems in the WoL code.
Change: Fixed by: 1. using sort mode. 2. setting up mac address correctly.
Impact: None.
Enhancements: ------------- 1. Change: Added support for non-dword and non-aligned write access to eeprom, allowing ethtool -E to work.
Impact: None.
v1.0.11 (Sep. 24, 2004) ====================== Fixes: ------ 1. Problem: (CQTO600) Kernel panic when attempting to ftp on Fedora kernel.
Cause: skbuffs are 4-byte aligned on Fedora, causing the rx headers to be misaligned. skbuffs are 16-byte aligned on other standard kernels.
Change: Removed any assumptions about skbuff alignment and added code to align all rx skbuffs to 8-byte boundaries.
Impact: None.
Enhancements: ------------- 1. Change: Added netif_carrier_off to Driver init code so that the initial link state is off.
Impact: None.
v1.0.10 (Sep. 23, 2004) ====================== Fixes: ------ 1. Problem: (CQTO599) Driver fails to compile on RH 3.0ES.
Cause: Bug in poll_bcm5706 where bp is referenced without being defined.
Change: Fixed the minor bug.
Impact: None.
v1.0.9 (Sep. 23, 2004) ====================== Fixes: ------ 1. Problem: Jumbo frames not working reliably.
Cause: Bug in bcm5706_reuse_rx_skb.
Change: Fixed the bug so that the host address is properly copied from one BD to the other.
Impact: None.
Enhancements: ------------- 1. Change: Change the locking scheme for more reliable open/close/ioctl operations where the spinlock is needed.
Impact: None.
2. Change: Added minimum MTU size check for MTU changes.
Impact: None.
v1.0.8 (Sep. 20, 2004) ====================== Fixes: ------ 1. Problem: (CQTO561) Kernel panic on RH30EL after repeated driver load/unload.
Cause: Occasionally, the system is unable to map device registers, causing subsequent register access to fail.
Change: Added check for the return value from ioremap, and exit gracefully if it fails.
Impact: None.
2. Problem: (CQTO574) NETDEV WATCHDOG when running 5706 A1 on PCIX 133MHz slot.
Cause: Some hw register setup required for 133 Mhz.
Change: Added the register setup code.
Impact: None.
3. Problem: (CQTO468) Link does not go down after changing from 10Mbps full (forced) to 10Mbps half (forced) and vice versa when the link partner is also using forced speed.
Cause: Delay not long enough for the link to go down.
Change: Not practical to increase delay as a very long delay is needed for the link to go down. Added code to record the proper link speed and duplex when speed is forced so that ethtool will return the proper speed without the link going down. Note that the link will go down if the link partner has autoneg turned on, ensuring that the link partner will see the link change.
Impact: None.
Enhancements: ------------- 1. Change: Added power management and WOL during device close. This will allow WOL to work after Linux shutdown.
Impact: None.
2. Change: Changed driver so that ethtool will report invalid speed after ifdown.
Impact: None.
3. Change: Updated tpatfw.h
Impact: None.
v1.0.7 (Sep. 14, 2004) ====================== Fixes: ------ 1. Problem: (CQTO523) 5706 A1 hangs after a thousand iterations of load/ifup/ifdown/unload.
Cause: The driver may be servicing an interrupt within 15 msec of chip reset, causing the chip to hang. The problem was aggravated by the timer mode coalescing which created an excessive number of interrupts (hardware problem).
The Driver may also occasionally see the wrong firmware signature that will cause it to abort.
Change: Added synchronization to make sure all pending interrupts are serviced before resetting the chip. Also changed to collect mode coalescing. The firmware signature problem will be fixed in boot code.
Impact: The use of collect mode coalescing may affect performance.
2. Problem: (CQTO558) Unable to load driver on some early 2.6 kernels.
Cause: pci_dma_sync_single_for_* routines not defined on early 2.6 kernels.
Change: Added compatibility defines for earlier kernels.
Change: Added 15 msec delay after chip reset for A1.
Impact: None.
2. Problem: (CQTO468) Link does not go down after changing from 10Mbps full (forced) to 10Mbps half (forced) and vice versa.
Cause: Not enough delay after forcing link down.
Change: Added proper delay for link to go down.
Impact: None.
v1.0.5 (Sep. 02, 2004) ====================== Enhancements: ------------- 1. Change: Added support for ethtool -c, ethtool -C, ethtool -p, and firmware version for ethtool -i.
Impact: None.
Fixes: ------ 1. Problem: 5706C not advertising 1000 half duplex.
Cause: 1000 full duplex overwrites 1000 half duplex.
Change: Fixed the bug so that the 2 bits are or'ed together.
Impact: None.
2. Problem: ethtool -A does not change the flow control settings in all cases.
Cause: Flow control settings not zeroed out before setting new values.
Change: Minor bug fix to zero out the value.
Impact: None.
v1.0.4 (Sep. 02, 2004) ====================== Fixes: ------ 1. Problem: (CQTO504) Multiple NFS transfers will hang some connections.
Cause: Driver discards some receive packets when the error status is non-zero.
Change: Changed the driver to only discard receive packets when the defined error bits in the error status are non-zero.
Impact: None.
v1.0.3 (Sep. 01, 2004) ====================== Enhancements: ------------- 1. Problem: Driver does not support ethtool -t self test and ethtool -S statistics.
Change: Added ethtool self test and statistics.
Impact: None.
Fixes: ------ 1. Problem: (CQTO478) Kernel still panics when transmitting certain files using NFS after many iterations
Cause: Tx DMA stalls on certain UDP packets, causing NFS client to stall.
Change: More fixes made in firmware.
Impact: None.
v1.0.2 (Aug. 26, 2004) ====================== Enhancements: ------------- 1. Problem: Driver does not work on big endian machines.
Change: Ported and tested on SPARC64 machine.
Impact: None.
Fixes: ------ 1. Problem: (CQTO478) Kernel panics when transmitting certain files using NFS.
Cause: Tx DMA stalls on certain UDP packets, causing NFS client to stall.
Change: Fixed in firmware.
Impact: None.
2. Problem: (CQTO469) Unable to modify flow control parameters
Cause: Did not call setup_phy after the parameters are changed.
Change: Added call to setup_phy after parameters are changed.
Impact: None.
3. Problem: (CQTO467) 5706 does not autonegotiate properly after changing settings with ethtool.
Cause: This is an ethtool limitation as the proper advertising parameters are not passed to the driver properly.
Change: Implemented a new scheme to work around the problem to allow users to specify full autoneg, single speed autoneg, and fixed speed.
Impact: None.
4. Problem: ethtool -e does not work.
Cause: Various bugs in the nvram routines.
Change: Fixed and tested nvram routines on little endian and big endian machines.
Impact: None.
v1.0.1 (Aug. 18, 2004) ====================== Fixes: ------ 1. Problem: (CQTO459) 5706 NIC does not get link.
Cause: Boot code timing out in WAIT2 state before driver is ready.
Change: Moved the WAIT2 state ahead in the driver reset sequence as a temporary workaround until it is fixed in boot code.
Impact: None.
2. Problem: (CQTO463) Kernel panics when loading the driver on RH30EL (2.4.21-4.EL)
Cause: Older kernel used different API to allocate and register netdev.
Change: Added older APIs to be used on older kernels.
ServeRAID M and MR10 Series SAS Controller Driver for Linux (also supports MegaRAID 8480 SAS Controller)
Adapters Supported: - ServeRAID M5210e SAS/SATA Controller for IBM System x - ServeRAID M5210 SAS/SATA Controller - ServeRAID M5110 SAS/SATA Controller for IBM System x (81Y4481) - ServeRAID M5110e SAS/SATA Controller for IBM System x - ServeRAID M5120 SAS/SATA Controller for IBM System x (81Y4478) - ServeRAID M5025 SAS/SATA controller (46M0830) - ServeRAID M5016 SAS/SATA Controller for IBM System x (90Y4304) - ServeRAID M5015 SAS/SATA controller (46M0829) - ServeRAID M5014 SAS/SATA controller (46M0916) - ServeRAID M1115 SAS/SATA Controller for IBM System X (81Y4448) - ServeRAID M1015 SAS/SATA Controller (46M0831) - IBM ServeRAID MR10il SAS controller (44E8767) - IBM ServeRAID MR10is SAS controller (44E8695) - IBM ServeRAID MR10ie (CIOv) SAS controller (46C7167) - IBM ServeRAID MR10i SAS controller (43W4296) - IBM ServeRAID MR10k SAS controller (43W4280) - IBM ServeRAID MR10M SAS controller (43W4339) - MegaRAID 8480 SAS controller (39R8850)
Version 6.600.20.00-4 - Suggested ------------------- Fixes: - Fixed reboot issue in SLES 11.3 xen. Note: Device driver version number has not changed. Version 6.600.20.00
Version 6.600.20.00 - Suggested ------------------- Enhancement(s): - Add Support for ServeRAID M5210 and M5210e SAS/SATA Controller
Version 6.506.00.00 - Suggested ------------------- Retain Tip: Tip #28016 Enhancement(s): - Added ability for user to configure the maximum number of MSI-X vectors launched for M51XX and M1XX controllers.
Version 00.00.06.19 - Suggested ------------------- Fixes: - Fixed an issue where a kernel crash may occur in some cases, when megaraid_sas driver is loaded but controller is not present.
Version 00.00.06.15.01 - Suggested ------------------- Fixes: - Corrected version strings in the iso and rpm files. NOTE: No change to the device driver. Packaging fix only.
Version 00.00.06.15 - Suggested ------------------- Enhancements: - Add support for fpRead/WriteCapable & fpRead/WriteAcrossStripe - Add support for SLES 11 SP2.
Fixes: - Mask off MFI_FRAME_IEEE, MFI_FRAME_SGL64, MFI_FRAME_SENSE64 in megasas_mgmt_fw_ioctl() to prevent memory scribble issues from incorrectly built MegaCli frames. - Fixed reglockFlags for degraded RAID 5/6.
Version 00.00.06.12-01 - Suggested ------------------- Fix - Fixed issue where the device driver may fail to install with the following error: "389 SCRIPT INTERNAL INCONISISTENCY! REPORT TO IBM IMMEDIATELY" Note: No change to device driver version.
Version 00.00.06.12 - Suggested ------------------- Enhancement - Add support for ServeRAID M5016
Fixes - LSI Channel fixes
Version 00.00.04.38 - Non-critical ------------------- - Fixed issue where device driver could print message "kernel megasas: Command pool empty!" when the controller and megaraid driver are idle.
Version 00.00.04.37 - Suggested ------------------- - Fixed issue where the ServeRAID M1015 controller will halt during a OCR. - Fixed issue where OCR will not execute when the physical drives are in a power transition mode. - Fix issue where the ServeRAID M1015 controller will halt with a degraded RAID 5 array during IO.
Version 00.00.04.30 - Non-critical ------------------- - Added support for the ServeRAID M5025 SAS/SATA Controller
Fixes: - Fixed issue where during IO firmware faults at line : MonTask: line 1193 in file ../../raid/1078dma.c - Fixed issue where After 64 VD's are created using MSM the 'fdisk -l' command does not work. - Fixed issue where the firmware faults at line 739 in file ../../raid/1078main.c when rebooting after a recon. - Fixed issue where the drive partition is no longer present on the OS after importing a foreign configuration. - Fixed issue where Linux does not show the correct size of VD the second time if the 'fdisk -l' command is executed.
Version 00.00.04.17 - Non-critical ------------------- - Added support for the ServeRAID M1015 SAS/SATA controller. - Added support for the ServeRAID M5000 Series Advanced Feature Key.
Version 00.00.04.10 - Non-critical ------------------- - Added logic to support next-gen SAS2 controllers. - Added support for the ServeRAID M5015 and M5014 SAS/SATA controllers.
Version 00.00.03.23 - Non-critical ------------------- - Added support for the IBM ServeRAID MR10ie (CIOv) SAS controller. - Fixed an issue where, on a Xen kernel with guest OSs running, invoking kdump causes a system reboot. - Fixed an issue that results in a kernel panic when kdump is run on a system with heavy drive I/O.
Version 00.00.03.21 - Suggested ------------------- - Added support for the IBM ServeRAID MR10is SAS controller. - Fixed an issue where a command timeout would occur on a particular SAS hard drive, and would not recover. - Added a shutdown DCMD call to the shutdown routine to ensure a graceful shutdown. - Updated the list of required pre-built binaries. - Fixed an issue the could cause unexpected interrupts. - Fixed an issue where a memory sanity check would sometimes fail for a certain pointer on a 64-bit system, causing some enclosure components to not be seen.
Version 00.00.03.18 - Suggested ------------------- - Added support for the IBM ServeRAID MR10il SAS controller. - Fixed an issue where the OS would not reboot when a rebuild was in progress.
Version 00.00.03.13 - Non-critical ------------------- - Added support the IBM ServeRAID MR10i, MR10k, and MR10M SAS controllers. - Fixed an issue where, on boot to Xen kernel on Red Hat Enterprise Linux (RHEL) 5 64-bit, the user would encounter an “Error 13: Invalid or unsupported executable format” error.
Version 00.00.03.06 - Suggested ------------------- - Added diskdump support for Red Hat Enterprise Linux (RHEL) 3 and RHEL 4. - Set the reply_q_sz value to the maximum number of commands supported by the firmware. - On 2.4 kernels: fixed an issue where, when the system was rebooted, the shutdown routine did not get called; added a notifier for the reboot event and initiated a flush command from the reboot event handler. - Fixed issue where, on RHEL 3 Update 6, the driver would not install on AMD64 systems.
Version 00.00.03.01-1 --------------------- - Initial release ibm_dd_sraidmr_6_600_20_00-4_sles11_32-64_chg
=============================================================================== Emulex FC/FCoE Device Driver for Linux ===============================================================================
Device Driver Version: 10.0.794.0 Supported On: IBM System x
Problems Fixed: - Driver crash with Nexus link bounce - txcmplq list corruption cause hang/crash - Emulex LPE16002 possible PRIL issue causes crash - Lpfc spec file present in the source rpms has the wrong name
Device Driver Version: 8.2.2.24 Supported On: IBM System x, BladeCenter, and Flex
Problems Fixed: - RHEL 5.8 x86 blade crashes during FCoE failover test - Execution of internal loopback causes a crash - Issue which can cause multipath failover to not work properly
Incremental Interoperability: - IBM Flex System FC5052 2-port 16Gb FC Adapter - IBM Flex System FC5054 4-port 16Gb FC Adapter - IBM Tape unit interoperability - see SSIC for more information
Device Driver Version: 8.2.2.15 Supported On: IBM System x and BladeCenter
Problems Fixed: - FLOGI sent with Class 2 in-order bit set when Class 2 is set as unsupported class of service - OXID Reused before RA_TOV without RRQ to recover - Intermittently storage paths will not recover after switch reboot
Device Driver Version: 8.2.1.4 Supported On: IBM Flex
Problems Fixed: - Fixed debug helper routine failed to dump CQ and EQ entries in non-MSI-X mode - FLOGI sent with Class 2 in-order bit set when Class 2 is set as unsupported class of service - Fixed boot from san failure when SLI4 FC device presented on the same PCI bus - Fix ABTS recovery to be FC spec compliant - Fixed not reporting logical link speed to SCSI midlayer when QoS not enabled - Fix performance problem in pt2pt mode - Fixed SCSI host create showing wrong link speed on SLI3 HBA ports - Update text for misconfigured port messages - Fix discovery bug when swapping cables
Interoperability since previous release: - No new interoperability
Device Driver Version: 8.2.0.145 Supported On: IBM System x and BladeCenter
Problems Fixed: - Kernel panics with FCoE on HS23 in SLES 11.2 x86_64. Also requires a SLES11.2 kernel update - FLOGI sent with Class 2 in-order bit set when Class 2 is set as unsupported class of service
Interoperability since previous release: - RHEL6.3 GA Kernel
Device Driver Version: 8.2.0.134 Supported On: IBM System x and BladeCenter
Problems Fixed: - Fixed system crash due to not providing SCSI error-handling host reset handler - Debug helper utility routines for dumping various SLI4 queues - Fix unsol abts xri lookup - Fixed issues with LPe16000 to LPe16000 discovery - Fix driver crash during back-to-back ramp events - Reregister VPI for SLI3 after cable moved to new Saturn port - Fix log message 2597 displayed when no error is detected - Fixed FCP LOG for easier Finisar trace correlation - Fix kernel panic when going into to sleep state - Fix error message displayed even when not an error - Fix Read Link status data - Fix unable to create vports on FCoE SLI4 adapter - Fix initiator sending flogi after acking flogi from target - Fix the case where an array controller does not apply FCP priority rules - Added support for handling SLI4-port XRI resource-provisioning profile change - Change default DA_ID support from disabled to enabled - Fix bug with driver unload leaving a scsi host for a vport around - Update copyright date for files modified in 2012 - Fix bug with mailbox handling of REG_VFI and cable pull - Used PCI configure space read to flush PCI function reset register write - Update copyright date for files modified in 2012 - Fixed system panic when extents enabled with large number of small blocks - Fixed system panic during EEH recovery - Fix resource leak when acc fails for received plogi - Fix SLI4 driver module load and unload test in a loop crashes the system - Fix missing CVL event causing round-robin FCF failover process to stop - Fix deadlock during adapter offline request - Fix same RPI registered multiple times after HBA reset - Fix driver handling of XRI Aborted CQE response - Fix port and system failure in handling SLI4 FC port function reset - Fix bug with driver not sending a LOGO with vport delete - Fix KERNEL allocation while lock held - Make BA_ACC work on a fully qualified exchange - Fix for SLI4 Port delivery for BLS ABORT ACC - Fix ndlp nodelist not empty wait timeout during driver unloading - Fix mailbox and vpi memory leaks - Fix for FDISC failures after firmware reset or link bounce - Limit what management ELS and CT commands can be issued according to latest management specification - Fix for driver using duplicate RPIs after 16Gb/s adapter port reset - Fix discovery problem when in pt2pt - Fixed failure in handling large CQ/EQ identifiers in an IOV environment - Fix Locking code raises IRQ twice - Fix driver not returning when bad ndlp found in abts error event handling - Added driver logs in area of SLI4 port error attention and reset recovery
Device Driver Version: 8.2.0.122 Supported On: IBM System x and BladeCenter
Problems Fixed: - Fix bug with driver returning the wrong ndlp - Fix driver behavior when receiving an ADISC - Fixed PCI loopback diagnostic test through hbaCmd on SLI4 port failure - Fixed unbounded firmware revision string from port caused the system panic - Fix driver does not reset port when reset is needed during - Changed SLI4 FC port internal loopback from outer serDes to inner internal - Fix ELS FDISC failing with local reject / invalid RPI - Fix REG_RPI fails on SLI4 HBA putting NPort into NPR state - Fix NMI seen due to CQE starvation - Fixed SLI4 FC port obtain link type and number dependent on link connection - Fixed SLI4 FC port internal loopback without SFP and external link/loopback plug - Fix driver incorrectly building fcpCdb during scsi command prep - Fixed FCP EQ memory check prevent initialize to single interrupt vector case - Fixed system panic duringEEH recovery on SLI4 FC port - Fix FLOGI fails with invalid RPI (0x04) after connecting to a arbitrated loop - Fix ELS SCR failing with local reject / invalid RPI - Fix SLI4 port failures after firmware reset or dump - Fix port reset log messages indicate error when no error is seen - Fixed an issue where HBQ buffers are uninitialized in the base driver - Fixed missing hbalock protection on setting/clearing bit in phba->link_flag - Fixed logging mailbox error log messages during SLI4 FW download using HbaCmd - Fixed illegal state transition during driver unload - Fixed SLI4 FC port Internal and External loopback diagnostic tests - Fix bug with driver erroneously logging a kernel error message - Fix a crash while deleting 256 vports - Fix vport never finished discovery if switch runs out of resources - Fix kernel build warnings - Fix kernel panic when putting board in offline state twice - Fix PCI read failure looks like a over temperature event - Fixed driver event reporting to mgmt on error attention due to forced dump - Fix not displaying firmware rev for BE UCNA boards - Fixed ABTS failure logic not rediscovering targets - Fix bug with driver not byte swapping extended mailbox data - Fix premature ndlp cleanup after second target LOGO - Fix Link pull causes I/O failures - Add loop support for sli4 fc - Fixed OCM failing COMN_READ_OBJECT and COMN_WRITE_OBJECT mailbox pass- through - No longer read fcoe parameters if board is not fcoe - Added restore state and error log when sysfs board_mode attribute access failed - Added support for SLI4_CONFIG non-embedded COMN_GET_CNTL_ADDL_ATTR pass-through - Added support for SLI4 FC port persistent linkdown through config region 23 - Fix for ABTS.Do not free original IOCB whenever ABTS fails - Fixed Linux driver inconsistency in reporting FC host port-state through OCM - Fix firmware upgrade attempt on unsupported adapter - Fix incomplete message number 2889 - Fix system crash when Lancer fails to initialize - Fixed fcpi param length when not using an sgl - Fix virtual fabrics bit set in FLOGI incorrectly - Fix unsupported link speed accepted by SLI4 port - Incremented minor management version to reflect additional "protocol" sysfs attribute - Fix kernel build warnings - Modify WQ handling to use entry_repost - Added a sysfs attribute "protocol" to report SLI4 port link protocol type - Added SLI4 INTF_TYPE and SLI_FAMILY as sub-field to the fwrev sysfs attribute - Added structure to support T10 DIF in SLI4 - Fix performance slowed due to too many register accesses - Fix a possible driver crash when cfg_fcp_eq_count is zero - Fixed non-embedded COMMON_GET_CNTL_ATTR mbox command failed with status 0x4 - Changed the way of SLI4 device detecting physical port name - Fixed FCP policy exchange management rule parsing - Add new check to lpfc_decode_firmware_rev to handle releases that have an 'X' - Fixed RPI leaks in ELS protocol handling - Fix kernel crash during boot with SLI4 card installed - Fixed NPIV FDISC failure on SLI4 if-type 2 ports - Moved fcp policy structs - Fixed driver failed to follow IP reset procedure in SLI4 error attention handler - Fixed fcp underrun reporting - Fix sysfs lists fabric name for port that has been disconnected from fabric - Added support for policy exchange management - Changed the timeout to 300 seconds for SLI_CONFIG (0x9B) mailbox command - Fixed a driver handling IP reset issue when PCI read return error - Fixed casting problem in calculating tx_words statistics - Fixed compiler warningdue to uninitialized local variable - Added proper error code return for libdfc calling API to make proper decisions - Fix sli4 mailbox status code. Management software has dependencies - Made proper error code return for libdfc calling API to make proper decisions - Made error log include PCI BAR bitmap from kernel when enable PCI device failed - Fixed incomplete scsi messages displayed - Change log message in lpfc_sli_set_dma_length() - Completed missed FCF priority failover - Fixed not recovering SLI port in handling error attention with RN bit set - Fixed two crash cases when unsolicted ELS ECHO_CMD is received - Fix direct connect does not come up for SLI4 FC ports - Fixed long wait when firmware reset to a SLI port without required privilege - Fix driver firmware update to match new firmware image format - Fix SLI4 CT handling for sequences > 4K - Fixed handling of unsolicited frames for vports - Fixed crash when aborting els IOs - Fixed handling of CVL for vports - Fix up CT and oxid/rxid for unsol rcv frames - Fixed mailbox double free panic - Added fcf priority record selection for fcf failover - Fixed compiler warning for putting large amount of memory on stack - Fixed hbacmd listhbas took very long time when remote initiators present in zone - Fixed driver build not building in debugfs even if kernel CONFIG_DEBUG_FS=y is set - iDiag added SLI4 device PCI BAR memory mapped reigster access methods - iDiag changed command structure data array indexing by using macro defines - Ported iDiag pass-through multi-buffer mbox command capture and dump extension - Ported new SLI4 FC device loopback test and link diagnostic test supports - FLOGI payload has Multiple N_port_ID set when lpfc_enable_npiv clear - Add sysfs logging when writeable parameters are changed - Fixed new ASIC device-mgmt SYSFS pass-through failed multi-buffer fw download - Fixed memory leak due to failure to release mailbox command when completed - Brought debugfs accessing new ASIC extents information into the iDiag framework - Added wait for SLI port status register for readyness following firmware reset - Consolidated duplicating macro definitions - Implement debugfs support for resource extents - iDiag method for read write bitset bitclear access to new ASIC control registers - Fixed failure in pass-through mbox command with multiple number of large buffers - iDiag method for endian explicit dumping at iussue SLI4 mailbox command routine - iDiag ported debugfs method for dumping mbox from SLI4 issue mbox cmd routine - Added request for PCI funndamental reset to support EEH recover on P7 platform - iDiag ported debugfs inline mailbox command capture and dump utility - Fixed failure to enable PCIe AER prevent driver initialize and attach to device - Fix EEH recovery so state is saved after every PCI reset for SLI4 - Moved INIT_LIST_HEAD to inside of lpfc_mgmt_issue_sli_cfg_ext_mbox routine - New ASIC device management pass-through mbox extension with multi-buffer support - Fix FC Port swap on SLI3 adapters - Fixed Virtual link loss during Face plate failover test - Fix vpi initialization in lpfc_init_vfi - Added driver capability of reseting new ASIC firmware and device from sysfs entry - Added capability of inducing new ASIC firmware dump obj file to flash filesystem - Add firmware upgrade code to driver - Added 100ms delay before driver action following IF_TYPE_2 function reset - Fragment ELS and SCSI SGE lists based on Extent regions - Fixed potential missed SLI4 device initialization failure conditions - FixedBack to back Flogis sent without a logo - Add model names for new hardware - Fix bug with lpfc driver not updating the wwnn and wwpn after a name change - Set the maximum SGE size to 0x80000000 when HBA does not have any restriction - Fix SLI3 and non-NPIV crashes with new extent code - Fix CT command never completing on Big Endian system - Refactor lpfc_sli4_alloc_extent some more - Restore SLI4_PARAMETER mailbox can fail as nonerror functionality - Do not post RPI Headers to SLI4 port that support extents - Framework for new ASIC device management multi-buffer mbox passthrough support
=============================================== Change History =============================================== Document Name: Change History Document Status: IBM General Avalibility Document Version: 3.2.3.0 Latest Driver Version: 3.2.3.0 Document Updated: 09/20/2013 Product: Brocade FC HBA / FCoE CNA
=================================================
Please visit www.brocade.com/hba for full documentation, additional drivers, and management applications.
Version 3.2.3.0 New Features and Feature Enhancement: - Support for patching firmware via boot image - Support for Linux PTP - Support for UEFI Health Check Protocol - Support for SLES11SP3
Version 3.2.1.1 Fixes and Enhancements: - Firmware update to address the thermal notification issue
Version 3.2.1.0 New Features and Feature Enhancement: - Support for "IBM Flex System FC5024D 4-port 16Gb FC Adapter" PART_NUMBER "95Y2381" - Support for RHEL5.9 and RHEL6.4
Fixes and Enhancements: - Enhanced Linux driver data path to properly handle IPv6 packets. - Enhanced Linux driver to make sure user configured path tov value is persistent and is not changed due to change in dev_loss_tmo.
New Features and Feature Enhancement: - For Brocade 8x5/4x5, I/O interrupt latency values are dynamically updated. Changes are effective for all the ports on the given adapter. - Addressed infrequent PSOD in VMware ESX with iSCSI or VLAN configured traffic in DCB enabled network. - Enhanced BR1860 Tape IO performance. - Improved BR1860 initialization on Xen kernel.
Fixes and Enhancements: - BB Credit Recovery - Forward Error Correction (FEC) - Diagnostic Port (D-Port) - LUN Level IO Latency/Stats - UCM (Unified Configuration Manager) - Windows Network Performance and scalability enhancement
Version 3.1.0.0 Key features and enhancements supported for the software release 3.1.0.0 include the following:
New Features: - D-port support between Brocade 16Gb HBAs and Brocade 16Gb FC switch platforms with FOS v7.0.1 and later releases - FC-AL support for direct attach to storage - Ability to assign minimum bandwidth to each vNIC - Queue Depth adjustment - FC QoS set by percentage - Performance enhancements in Ethernet drivers - Technology Preview support of 1860 HBA on Power PC architecture
Fixes or Enhancements: - Resolved an issue where HCM Agent may not start if BR1860 adapter is configured in NIC mode. - Improved stability with Hyper-V and Teaming configurations. - Resolved I/O errors when running traffic with Brocade HBAs(models 415, 425, 815, 825, and 804), if the server’s PCI max read request size is configured to be 2K or greater with PCI Gen2x8.
Version 3.0.0.0 Fixes and Enhancements: - Added support for Brocade 1860 AnyIO Fabric Adapter (User configurable port mode - FC or NIC or CNA) - Added Fibre Channel 16G Support - Enabled Fabric Assigned Address in Fibre Channel Fabric - Added PF based Virtualization – vHBA - Enhanced CLI, HCM GUI and CIM support in inbox drivers. - Added PF based Virtualization - vNIC - Added iSCSI over DCB Support - Added Multiple Tx Priority Queues Support - Added SNMP Support
Version 2.3.0.3 Fixes and Enhancements: - Enhanced SNIA API to report port speed of 4 and 8Gbps in SNIA format. - Enhanced XIV array interoperability that addresses a data integrity corner case. - Enhanced the transmit path handling in Linux Network Driver to avoid a corner case that could lead to transmit path stall. - Enhanced the Linux Adapter Software installer script to update the initrd with the correct name even when there are multiple copies of the OEM specific initrd(s).
Version 2.3.0.0 Enhancements: - Enabled HP DL120 server to support Boot over SAN with two Brocade HBAs installed. - Improved network driver CPU and performance optimization. - Enabled automated target and LUN discovery of enterprise HDS storage once LUN masking has occurred. - Improved Tivoli interoperability to meet device display requirements.
Version 2.2.0.1 Added capability to handle ADISC frames. Unhandled ADISC use can cause SAN boot failure when booting from IBM storage array.
Version 2.2.0.0 Adds support for bootcode updates to Bladecenter 10G Converged Network Adapters
Version 2.1.0.0 Adds support for bootcode updates to 10G Converged Network Adapters
Version 2.0.0.0 Initial release for 4/8G FC HBAs brcd_dd_fc_bfa-3_2_3_0_sles11_32-64_chg
======================================================= Change History for Qlogic Converged Network Adapter STOR FCoE Driver ======================================================= Document Name: Change History Document Status: IBM General Avalibility Document Version: 8.2 Latest Package Version: 8.06.00.10 Latest Driver Version: 8.06.00.10 Document Updated: 10/05/2013 Product: Qlogic FCoE Linux Device Driver
Please visit www.qlogic.com/hba for full documentation, additional drivers, and management applications.
Version 8.06.00.10 Fixes and Ehancements:
Software/Driver
* Added T10 DiF/DiX support for ISP83xx.
* ISP83xx CNA support * IDC support for three protocols. * Loopback support. * Beacon support.
* Added support for bidirectional commands
* Added support for MCTP dump
* ISP83xx(16G FC) support for Xenserver 6.0 and Oracle UEK.
* SRB Consolidation.
* RSCN handling changes.
* Increase in support of maximum fibre devices.
* Enhancements to support ISP83xx (Limited support). * Driver features supported * 10GB link support only * Port device discovery * LUN discovery * I/O * Perturbations * SG resets of host and SCSI devices.
* Driver features not supported * Beacon support * Loopback * T10 DIX/DIF * SFP read/write * QCC GUI Support * QCC CLI Support * NPIV * Multi-Queue * Boot from SAN * FC-Tape * SLES10.3 driver: * Fix not to MPI reset on ISP83xx is not included.
* Implemeted beacon on/off for ISP82xx.
* Add support for ISP82xx to capture dump (minidump) on failure.
* Provide method for updating I2C attached VPD.
* Resync with latest ISP24xx/25xx firmware (5.08.00).
Industry Standards Compliance ----------------------------- * N/A
3. Bug Fixes
The following fix has been made to the Fibre Channel and FCoE Adapter Inbox Driver Update for Linux Kernel 2.6.x and 3.x:
* 8.04.00.12.xx.y-k * Update the copyright information. * Display the lock owner on lock acquire failure. * Move loopback mode reset after chip reset check. * Extra loopback error handling for ISP83xx. * Do link initialization on get loop id failure. * Do MPI reset only for 81xx.
V2632 (RHEL 6.x, SLES 11.x, Citrix 6.0, UEK): * Revert "qla2xxx: Optimize existing port name server query matching." * Revert "qla2xxx: Avoid losing any fc ports when loop id's are exhausted." * Don't free pool that wasn't allocated. * Unload hangs after issuing BSG commands to vport.
Citrix 6.0: * Create initrd as a part of installation and removal of the driver rpm. * RPM install should install driver under extra instead of driver directory.
RHEL 5.x, SLES 10.x: * MBA_IDC_NOTIFY case should fallthru. * Add fw_dump_size sysfs attribute file. * Add test for validity of virtual host in netlink interface.
SLES 10.x: * Add 8031/2031 cases to request firmware.
* 8.04.00.11.xx.y-k * Move marking fcport online ahead of setting iiDMA speed. * Add 16Gb/s case to get port speed capability. * Get VPD information from common location for CNA. * Dont clear drv active on iospace config failure. * Display that driver is operating in legacy interrupt mode. * Add "16" speed to link speeds array in qla2x00_iidma_fcport() function * Correct race in loop_state assignment during reset handling. * Reject loopback request if one is already in progress. * Update the FTP site references in the driver sources.
V2632 (RHEL 6.x, SLES 11.x Citrix 6.0 and UEK): * Obtain loopback iteration count from bsg request. * Parameterize the link speed string conversion function. * Update ql2xextended_error_logging parameter description with new options. * Fix typo in qla2xxx driver. * Free rsp_data even on error in qla2x00_process_loopback(). * Avoid null pointer dereference in shutdown routine.
RHEL 5.x: * Remove fabric_logout() calls from qla2x00_dev_loss_tmo_callbk() function.
SLES10.x: * Clear local references of rport on device loss timeout notification from FC transport.
* 8.04.00.10.xx.y-k * Honor status value of 2 for report-id acquisition. * Ignore driver ack bit if corresponding presence bit is not set. * Add Gen3 PCIe speed 8GT/s to the log message. * Acquire risc semaphore before resetting ISP.
V2632 (RHEL 6.x, SLES 11.x Citrix 6.0 and UEK): * Ramp down queue depth for attached SCSI devices when driver resources are low. * Determine the number of outstanding commands based on available resources. * Fix for kernel crash when external loopback diagnostic is run through BSG interface. * Fix coccinelle warnings in qla2x00_relogin. * Test and clear FCPORT_UPDATE_NEEDED atomically. * Use correct Request-Q-Out register during bidirectional request processing * Fix typo in qla83xx_fw_dump function. * Move noisy Start scsi failed messages to verbose logging level. * Fix for warnings reported by sparse.
RHEL 5.x: * Inclusion of 4G/8G firmware version 5.08.00. * Log message when qla2xenablemsix module parameter is set to 2( MSI mode) and adpater does not support MSI mode. * Revert "qla2xxx: Use GFF_ID to check FCP-SCSI FC4 type before logging into Nx_Ports" * Revert "qla2xxx: No fcport FC-4 type assignment in GA_NXT response."
Citrix 6.x: * RPM build should hide the directory naming convention from user.
* 8.04.00.09.xx.y-k * No fcport FC-4 type assignment in GA_NXT response. * Fix checkpatch error in qla2xxx_mctp_dump. * Change in setting UNLOADING flag and FC vports logout sequence while unloading qla2xxx driver. * Clear unsupported 'states' during Get-FW-State queries.
V2632 (RHEL 6.x, SLES 11.x Citrix 6.0 and UEK): * Pass correct parameters while creating an initrd. * Remove spurious taking of ha->vport_slock spinlock.
UEK: * Add macro for kernel extended version.
RHEL 5.x: * Use GFF_ID to check FCP-SCSI FC4 type before logging into Nx_Ports. * Pass correct parameters while creating an initrd.
8.04.00.08 Initial release of Qlogic 10Gb FC Driver for RHEL5
qlgc_dd_fc_qla2xxx-8_06_00_10_sles11_32-64_chg
=============================================================================== Emulex NIC Device Driver for Linux ===============================================================================
Device Driver Version: 10.0.800.0 Supported On: IBM System x
Problems Fixed: - Low bi-di throughput seen on 1g ports of HS-23 LOM - Multiple performance improvements - Bonding driver takes approx 20 seconds to be ready
Incremental Interoperability: - RHEL 5.10 - RHEL 6.5 - XE-102 and XE-104 ASIC (OCx14xxx) - Support for set and get channels ethtool operation
Known Issues: - SR-IOV is supported with the following Linux distributions: * RHEL 6.4 and above 64-bit with KVM * SLES11 SP3 and above 64-bit with KVM
NOTE: Guest operating system support is dependent on the Emulex driver version installed in the guest.
Device Driver Version: 4.6.267.4 Supported On: IBM System x, BladeCenter, and Flex
Problems Fixed: - Under certain conditions, performance issues may be seen with multi-channel in RHEL6.4 KVM configurations - Under certain conditions, performance issues may be seen with multi-channel in RHEL6.4 SR-IOV configurations - SR-IOV configuration section of the Linux NIC Driver Documentation has been modified to improve clarity
Incremental Interoperability: - S3 Resume on IBM Flex - SLES 11.3 on IBM System x and BladeCenter
Known Issues: - SR-IOV is supported with the following Linux distributions: * RHEL 6.3 and 6.4 64-bit with KVM * SLES11 SP2 and SP3 64-bit with KVM
NOTE: Guest operating system support is dependent on the Emulex driver version installed in the guest.
- Use of SR-IOV with the XEN hypervisor is not supported at this time.
- Use of SR-IOV with the KVM hypervisor requires the use of macvlan network interfaces.
Device Driver Version: 4.6.148.0 Supported On: IBM System x and BladeCenter
Problems Fixed: - Ethernet performance issues in a variety of workloads - VFs are not displayed after driver re-load when is VFs attached to VM - vLAN tagging in Switch Agnostic vNIC mode
Incremental Interoperability: - RHEL 5.9 - RHEL 6.4 - Network performance varies with workload. An ethernet driver tuning script and instructions is now included with the be2net driver. - Switch Independent Mode within hypervisor OS's
Known Issues: - Multi-channel is not supported in RHEL5.x XEN. This is a kernel limitation - Under certain conditions, performance issues may be seen with multi-channel in RHEL6.4 KVM configurations - Under certain conditions, performance issues may be seen with multi-channel in RHEL6.4 SR-IOV configurations - SR-IOV is not supported with RHEL5.x XEN
Device Driver Version: 4.4.180.0 Supported On: IBM Flex
Device Driver Version: 4.2.389.0 Supported On IBM System x and BladeCenter
Problems Fixed: - Unloading the driver hangs the system after running IPv6 traffic - Link status messages cleaned up when in Switch Agnostic mode - Miscellaneous network performance issues to improve throughput - Miscellaneous problems related to SRIOV to improve usability - Ethtool wol command displays wol enabled even when disabled - Ethtool speed reported as 10000Mb/s for disabled devices in Switch Agnostic mode
Incremental Interoperability: - RHEL6.3 GA Kernel - Increase default B/W for SRIOV vf's to 10Gb from 100Mb
Device Driver Version: 4.1.413.0 Supported On: IBM System x and BladeCenter
Problems Fixed: - WOL changes for Linux NIC driver as mentioned in Bug# 24543 - SR IOV UE when attempt to do multiple (3 times) driver load/unload - Speed is 10000Mb/s for Disabled devices in UMC Mode - Incorrect Duplex value is shown for unconnected port of NC552m in Rhel6.1 32bit - SLES 11 SP2 GMC: Enable support for Lnx NIC Driver - SRIOV: When VGT is configured for a VF, ip link show doesn't display it for the VF configured. - RHEL 5.8 GA: Enable support for Lnx NIC Driver - ip link command with vlan = 4095 has toggling effect - ip link command with vlan =0 should remove guest VGT privilege
Device Driver Version: 4.1.334.39 Supported On: IBM System x and BladeCenter
Problems Fixed: - SR-IOV: Can't load be2net driver in a VM after the VM has been rebooted - SR-IOV: Unload PF driver with VF driver loaded causes system instability - SR-IOV: VF MAC always gets Emulex OUI - SR-IOV: Partition the limited per port VLAN entries across VFs and PFs - Non Member VLAN packets not received in interface promiscuous mode in BE3 - Avoid CQ full condition in HW - be2net: use RX_FILTER cmd to program multicast addresses - account for skb allocation failures in ethtool stats - Support 60 second delay to Linux NIC driver to allow FAT dump completion on recovery from EEH - Link status is up [ethtool and OCM] when the bandwidth is assign 0 for UMC configuration - Remove msix module parameter - Use V1 version of COMMON_NTWK_LINK_STATUS_QUERY for Lancer. - Emulex: Ethtool failing to update FW - Emulex: Panic in be2net driver in SLES11-SP2-B7 on adapter - TCP ACKs from different connections are getting received in single queue - Multicast filtering feature not working on PPC - Exit of mcast promiscous mode not working - VLAN promiscous mode cannot be set on Lancer - Can't communicate after changing MAC address via VLAN interface - Improper memory accounting in received packets - WOL changes for Linux NIC driver as mentioned in bug - Transparent VLAN tagging feature not working in SR-IOV
=============================================== Change History =============================================== Document Name: Change History Document Status: IBM General Avalibility Document Version: 3.2.3.0 Latest Driver Version: 3.2.3.0 Document Updated: 09/20/2013 Product: Brocade FC HBA / FCoE CNA
=================================================
Please visit www.brocade.com/hba for full documentation, additional drivers, and management applications.
Version 3.2.1.0 New Features and Feature Enhancement: - Support for patching firmware via boot image - Support for Linux PTP - Support for UEFI Health Check Protocol - Support for SLES11SP3
Version 3.2.1.1 Fixes and Enhancements: - Firmware update to address the thermal notification issue
Version 3.2.1.0 New Features and Feature Enhancement: - Support for "IBM Flex System FC5024D 4-port 16Gb FC Adapter" PART_NUMBER "95Y2381" - Support for RHEL5.9 and RHEL6.4
Fixes and Enhancements: - Enhanced Linux driver data path to properly handle IPv6 packets. - Enhanced Linux driver to make sure user configured path tov value is persistent and is not changed due to change in dev_loss_tmo.
New Features and Feature Enhancement: - For Brocade 8x5/4x5, I/O interrupt latency values are dynamically updated. Changes are effective for all the ports on the given adapter. - Addressed infrequent PSOD in VMware ESX with iSCSI or VLAN configured traffic in DCB enabled network. - Enhanced BR1860 Tape IO performance. - Improved BR1860 initialization on Xen kernel.
Fixes and Enhancements: - BB Credit Recovery - Forward Error Correction (FEC) - Diagnostic Port (D-Port) - LUN Level IO Latency/Stats - UCM (Unified Configuration Manager) - Windows Network Performance and scalability enhancement
Version 3.1.0.0 Key features and enhancements supported for the software release 3.1.0.0 include the following:
New Features: - D-port support between Brocade 16Gb HBAs and Brocade 16Gb FC switch platforms with FOS v7.0.1 and later releases - FC-AL support for direct attach to storage - Ability to assign minimum bandwidth to each vNIC - Queue Depth adjustment - FC QoS set by percentage - Performance enhancements in Ethernet drivers - Technology Preview support of 1860 HBA on Power PC architecture
Fixes or Enhancements: - Resolved an issue where HCM Agent may not start if BR1860 adapter is configured in NIC mode. - Improved stability with Hyper-V and Teaming configurations. - Resolved I/O errors when running traffic with Brocade HBAs(models 415, 425, 815, 825, and 804), if the server’s PCI max read request size is configured to be 2K or greater with PCI Gen2x8.
Version 3.0.0.0 Fixes and Enhancements: - Added support for Brocade 1860 AnyIO Fabric Adapter (User configurable port mode - FC or NIC or CNA) - Added Fibre Channel 16G Support - Enabled Fabric Assigned Address in Fibre Channel Fabric - Added PF based Virtualization – vHBA - Enhanced CLI, HCM GUI and CIM support in inbox drivers. - Added PF based Virtualization - vNIC - Added iSCSI over DCB Support - Added Multiple Tx Priority Queues Support - Added SNMP Support
Version 2.3.0.3 Fixes and Enhancements: - Enhanced SNIA API to report port speed of 4 and 8Gbps in SNIA format. - Enhanced XIV array interoperability that addresses a data integrity corner case. - Enhanced the transmit path handling in Linux Network Driver to avoid a corner case that could lead to transmit path stall. - Enhanced the Linux Adapter Software installer script to update the initrd with the correct name even when there are multiple copies of the OEM specific initrd(s).
Version 2.3.0.0 Enhancements: - Enabled HP DL120 server to support Boot over SAN with two Brocade HBAs installed. - Improved network driver CPU and performance optimization. - Enabled automated target and LUN discovery of enterprise HDS storage once LUN masking has occurred. - Improved Tivoli interoperability to meet device display requirements.
Version 2.2.0.1 Added capability to handle ADISC frames. Unhandled ADISC use can cause SAN boot failure when booting from IBM storage array.
Version 2.2.0.0 Adds support for bootcode updates to Bladecenter 10G Converged Network Adapters
Version 2.1.0.0 Adds support for bootcode updates to 10G Converged Network Adapters
Version 2.0.0.0 Initial release for 4/8G FC HBAs brcd_dd_nic_bna-3_2_3_0_sles11_32-64_chg
=============================================================================== Emulex iSCSI Device Driver for Linux ===============================================================================
Device Driver Version: 10.0.803.21 Supported On: IBM System x
Problems Fixed: - Unable to OEMSEAddTarget or OEMSEDiscoverTaget successfully and get entries in mili2d.log - Emulex drivers are not working on RHEL5 and RHEL6 errata kernel updates - IO Read/Write almost halts with 'DMA: Out of SW IOMMU space' messages while running iSCSI Multipath I/O
Device Driver Version: 4.4.175.0 Supported On: IBM Flex
Problems Fixed: - Cleaned up a cosmetic problem with warning messages during driver compile from source - System crashes when we run simultaneous IO to 6 vNIC’s with iSCSI IO - Linux kdump kernel crashes during shutdown after capturing dump, if be1iscsi driver running
Device Driver Version: 4.1.402.0 Supported On: IBM System x and BladeCenter
Problems Fixed: - LUN is not getting detected for OEM CNA in SLES 11 SP2 64 bit OS - ioctl semaphore deadlock when running load/unload loop with target - SLES 11 SP2 GMC: Enable support for Lnx iSCSI Driver - RHEL 5.8 GA: Enable support for Lnx iSCSI Driver
Device Driver Version 4.1.334.39 Supported On: IBM System x and BladeCenter
Problems Fixed: - Emulex: Warning messages seen while building Emulex drivers on RHEL platform - Unable to load be1iscsi driver during iSCSI boot OS install - Modprobe be1iscsi hangs when system with max targets login - be1iscsi unload hangs the system - fw rebooted on 1st mbox cmd after driver load > unload > load - Failed to initialize iscsi driver - need to define DMA_32BIT_MASK / DMA_64BIT_MASK in Linux kernel 3.x.x
Firmware Version: 2.01a11 Boot Code Version: 5.12a13 Supported On: IBM System x and BladeCenter
Problems Fixed: - Emulex FC Adapter does not auto-enable SAN boot mode when boot target configuration is made via IFM (BOFM) - Emulex FC configuration utility is in the wrong F1 setup screen - IBM CIOv adapter connected to Brocade 8 Gig FC BladeCenter switch intermittently Links up at less than 8 Gig
Firmware Version 2.01a3 Boot Code Version: 5.12a5 Supported On: IBM System x and BladeCenter
Incremental Interoperability: - Enhanced timeout notifications for processing abort failures.
Problems Fixed: - All multi-abort I/Os are returned on the same ring from which the ABORT_MXRI command was received. - Changed the TRCV response in the abort state to CMD RJT to enable the TRSP to be processed. - Corrected an issue with blocked TSEND operations. - Corrected a buffer leak issue with RRQ exchanges. - Corrected an issue where the TRCV IOCB was de-queued improperly causing a XFR_RDY flood. - Corrected an issue where the OXID field was not loaded in the XRI_ABORTED IOCB. - Corrected an issue in recognizing whether an EEPROM is present.
Firmware Version: 10.0.803.13 Supported On: IBM System x
Problems Fixed: - IBM Feature on Demand for storage keys now works with Optimized Boot enabled - Link detection time improved from ~70 secs on DAC cable insertion/removal
Incremental Interoperability: - Unified Fabric Protocol on IBM System x Servers
Known Issues: - After making changes to any options in the sub-menus under 'controller configuration' in the Emulex UEFI NIC configuration utility and escaping to the prior menu, there is no prompt to save the changes. Be sure to select 'Save' before exiting the configuration menu. Applies to some legacy rack and blade servers. - Intermittently, when changing the multichannel mode, the system will not auto-reboot after exiting F1 UEFI setup and will continue through POST. Manually reboot the server to ensure all changes are applied. Applies to some legacy rack and blade servers. - When using a Cisco Nexus 4001i Switch Module, intermittently the 10Gb link may come up as 1Gb link speed. An internal switch port bounce will typically establish a 10Gb link. Setting the switch port speed to fixed 10000 will also allow a guaranteed 10Gb connection. More info available in the Cisco Nexus 4001i Switch Module firmware release notes.
Firmware version: 4.6.281.26 (supported on IBM System x, BladeCenter and Flex)
Problems Fixed: - CN4054 VPD is not valid during/after IMM flash - Links go down after 497 to 498 days in VMWare - Send 'link down' to switch if UE occurs on ASIC
Incremental Interoperability: - Emulex Dual Port 10GbE SFP+ VFA IIIr for IBM System x - Emulex Dual Port 10GbE SFP+ Embedded VFA IIIr for IBM System x
Known Issues: - After making changes to any options in the sub-menus under 'controller configuration' in the Emulex UEFI NIC configuration utility and escaping to the prior menu, there is no prompt to save the changes. Be sure to select 'Save' before exiting the configuration menu. Applies to some legacy rack and blade servers.
- Intermittently, when changing the multichannel mode, the system will not auto-reboot after exiting F1 UEFI setup and will continue through POST. Manually reboot the server to ensure all changes are applied. Applies to some legacy rack and blade servers.
- When using a Cisco Nexus 4001i Switch Module, intermittently the 10Gb link may come up as 1Gb link speed. An internal switch port bounce will typically establish a 10Gb link. Setting the switch port speed to fixed 10000 will also allow a guaranteed 10Gb connection. More info available in the Cisco Nexus 4001i Switch Module firmware release notes.
Firmware version: 4.6.281.21 (supported on IBM System x, BladeCenter and Flex)
Problems Fixed: - OCe10 VFA CNAs stuck in "Switch Independent Mode" - Port Identification fails on Port 1 under uEFI menu for PCIe rack VFA
Incremental Interoperability: - Emulex Dual Port 10GbE SFP+ VFA IIIr for IBM System x - Emulex Dual Port 10GbE SFP+ Embedded VFA IIIr for IBM System x - IBM Flex System CN4054R 10Gb Virtual Fabric Adapter - IBM Ivy Bridge CPU Based Servers
Known Issues: - After making changes to any options in the sub-menus under 'controller configuration' in the Emulex UEFI NIC configuration utility and escaping to the prior menu, there is no prompt to save the changes. Be sure to select 'Save' before exiting the configuration menu. Applies to some legacy rack and blade servers.
- Intermittently, when changing the multichannel mode, the system will not auto-reboot after exiting F1 UEFI setup and will continue through POST. Manually reboot the server to ensure all changes are applied. Applies to some legacy rack and blade servers.
- When using a Cisco Nexus 4001i Switch Module, intermittently the 10Gb link may come up as 1Gb link speed. An internal switch port bounce will typically establish a 10Gb link. Setting the switch port speed to fixed 10000 will also allow a guaranteed 10Gb connection. More info available in the Cisco Nexus 4001i Switch Module firmware release notes.
Firmware version: 4.6.281.8 Supported On: IBM System x, BladeCenter, and Flex
Problems Fixed: - HW iSCSI offload is now supported in UFP Mode (UFP limited to IBM Flex) - Server may hang during boot with multichannel disabled with switch default settings. The IBM 10Gb Virtual Fabric Switch has trunking enabled and the Brocade Converged 10Gbe Switch Module has ports in "Access" mode. If the Brocade Converged 10Gbe Switch Module ports are switched to trunking mode, the hang no longer occurs. - When using Config Patterns with virtual MACs the bandwidth settings are are intermittently reset after some number of server reboots.
Incremental Interoperability: - IBM Flex System Fabric SI4093 System Interconnect Module - IBM Flex System EN6131 40Gb Ethernet Switch - IBM Flex System x222 10Gb Virtual Fabric LOM - SLES 11.3 on IBM System x and BladeCenter - Complete NIC/iSCSI/FCoE support for ASU/Config Patterns for Flex and ASU for IBM System x & BladeCenter
Known Issues: - After making changes to any options in the sub-menus under 'controller configuration' in the Emulex UEFI NIC configuration utility and escaping to the prior menu, there is no prompt to save the changes. Be sure to select 'Save' before exiting the configuration menu. Applies to some legacy rack and blade servers. - Intermittently, when changing the multichannel mode, the system will not auto-reboot after exiting F1 UEFI setup and will continue through POST. Manually reboot the server to ensure all changes are applied. Applies to some legacy rack and blade servers. - When using a Cisco Nexus 4001i Switch Module, intermittently the 10Gb link may come up as 1Gb link speed. An internal switch port bounce will typically establish a 10Gb link. Setting the switch port speed to fixed 10000 will also allow a guaranteed 10Gb connection. More info available in the Cisco Nexus 4001i Switch Module firmware release notes.
Firmware version: 4.6.166.7 Supported On: IBM System x and BladeCenter
Problems Fixed: - When connected to Cisco Nexus 4k and 5k switches, the virtual link may not recover on a switch port bounce (shut/no shut) in an ESXi environment. A switch port re-bounce will recover the link. - When connected to Cisco Nexus 4k and 5k switches, OneCommand Manager reports CRC's and there is poor network performance in an ESXi environment
Incremental Interoperability: - ASU/Config Pattern configuration for iSCSI and FCoE (BE3) - UFP for iSCSI (BE3) - Support for using 10Gb ports with legacy 1Gb switches installed in a BladeCenter-S chassis or MSIM/MSIM-T expansion units in a BladeCenter-H or -HT chassis - Update Express System Packs now support Linux errata kernels - ESXi 5.1
Known Issues: - After making changes to any options in the sub-menus under 'controller configuration' in the Emulex UEFI NIC configuration utility and escaping to the prior menu, there is no prompt to save the changes. Be sure to select 'Save' before exiting the configuration menu. Applies to some legacy rack and blade servers. - Intermittently, when changing the multichannel mode, the system will not auto-reboot after exiting F1 UEFI setup and will continue through POST. Manually reboot the server to ensure all changes are applied. Applies to some legacy rack and blade servers. - Server may hang during boot with multichannel disabled with switch default settings. The IBM 10Gb Virtual Fabric Switch has trunking enabled and the Brocade Converged 10Gbe Switch Module has ports in "Access" mode. If the Brocade Converged 10Gbe Switch Module ports are switched to trunking mode, the hang no longer occurs. - When using a Cisco Nexus 4001i Switch Module, intermittently the 10Gb link may come up as 1Gb link speed. An internal switch port bounce will typically establish a 10Gb link. Setting the switch port speed to fixed 10000 will also allow a guaranteed 10Gb connection. More info available in the Cisco Nexus 4001i Switch Module firmware release notes.
Firmware Version: 4.4.180.3 Supported On: IBM Flex
Problems Fixed: - 10Gb ports intermittenly linking at 1Gb speed with the IBM Flex System Fabric EN4093/EN4093R 10Gb Scalable Switch. - Switch Configuration after an erase configuration is not reflected after reboot - 'Logical Admin Link' not enabled after applying BOFM in Switch Agnostic mode - IBM pre-boot Diagnostics NIC physical loopback test fails in Command and GUI mode - Multiple cosmetic issues with iSCSI UEFI BIOS - 10Gb ports do not detect 'Link Down' with some switches - When adding an iSCSI hardware target in UEFI through discovery login, the boot target setting is ignored.
Interoperability since previous release: - UEFI 2.3.1 Compliance - Increased VF count in SR-IOV (was 16 VFs per port, is now 32 VFs per port) - Support for next generation 10GbaseT PHY - Expose IBM Feature On Demand licensing information in UEFI configuration utility - IBM Universal Configuration Manager for Ethernet - IBM Unified Fabric Protocol - Ability to assign Switch Agnostic VLAN IDs without intermediate reboot - Changes to Personality or Multichannel in PXESelect allows further changes to be made w/o reboot - Support for IBM Flex System Fabric CN4093 10Gb Converged Scalable Switch
Known Issues: - HW iSCSI offload is not currently supported in UFP mode
Firmware Version: 4.1.422.8 Supported On: IBM Flex
Problems Fixed: - PHY Loopback fails on 10G ports - RH 6.2 and W2k8 servers crashed after shut/no shut the switch port with FCoE connection and 50 vlans configured - DSA: NIC physical loopback test fails in Command and GUI mode - Firmware update fails to update all VPD Code Level fields - DCBX does not converge with FW 4.1.422 on Cicso 5k.
Interoperability Since Previous Release: - Support for IBM Flex System x440 10Gb Virtual Fabric LOM
Firmware Version: 4.1.422.0 Supported On: IBM Flex
Problems Fixed: - SR IOV: Unable to ping IPV6 from DUT VF to Peer VF - Reading VPD from BE3 timesout making SR IOV fail in newer kernels - 1Gb devices are being suppressed by kernel during the PCI probe in SLES11 SP2 - MAC Loopback fails when Mgmt Adapter Creation fails - Failure of MAC loopback test after firmware update and warm reboot - Suppress efat dump mailbox commands in the efat dump log - Running ethtool with BE3 takes longer than expected after cable pull - Out of Order CQEs - TRACE_LOG function not printing the messages for some of the VF's - esx4/5 issue. svc target cannot be configured properly - RSCN is not generated by switch when a driver restarts - Port Link stays up even after switch removed
Interoperability Since Previous Release: - Support for IBM Flex System EN4054 4-port 10Gb Ethernet Adapter - Support for IBM Flex System CN4054 10Gb Virtual Fabric Adapter - Support for IBM Flex System x240 10Gb Virtual Fabric LOM - Support for IBM Flex System Manager 10Gb Virtual Fabric LOM
Firmware Version: 4.2.433.3 Supported On: IBM System x and BladeCenter
Problems Fixed: - Intermittent link status with IBM Virtual Fabric Switch when set to IBM Virtual Fabric Mode - The option to enable/disable SRIOV on HS23 LOM Port 0 is missing from OneCommand Manager. This selection is available in UEFI F1 setup. - Under high network stress, NMI errors can be seen with x3690 X5 and x3850 X5 - 10GbE ports running at 1GbE speed 10% below wirespeed at certain block sizes. - Unable to perform PXE boot with LPVID assigned to vNIC interface - 1Gb ports of HS23 do not handle tagging properly if multichannel mode enabled (pnic ok). Note: ESX driver patch also required. - Port flapping link after FW upgrade and "reboot" when connected to 10Gb PTM module (DAC)
Interoperability Since Previous Release: - Support for Emulex Virtual Fabric Adapter Advanced (BE2) for IBM BladeCenter - Support for Emulex Virtual Fabric Adapter (BE2) for IBM BladeCenter - Support for Emulex Virtual Fabric Adapter (BE2) for IBM System X
Known Issues: - All 10Gb KX4 ports must be used with 10Gb switches. They will not link at 1Gb. This applies to HS23 LOM and IBM BladeCenter VFA adapters only. - IPv6 IP address not visible via IMM GUI for IBM Option 90Y6456
Firmware Version: 4.2.412.0 Supported On: IBM System x and BladeCenter
Problems Fixed: - All VFS on Port 1 on optional Card unreachable from outside the host (x3750 M4) - 'Logical Admin Link' not enabled after applying BOFM in Switch Agnostic mode - IBM pre-boot Diagnostics NIC physical loopback test fails in Command and GUI mode - Multiple cosmetic issues with iSCSI UEFI BIOS - 10Gb ports do not detect 'Link Down' with some switches - 1Gb ports on HS23 LOM not able link up with IBM ICPM (FRU part 44W4486) in BCS chassis - Performance issues with specific DAC cables and SND top of rack switch
Interoperability Since Previous Release: - UEFI 2.3.1 Compliance - Increased VF count in SR-IOV (was 16 VFs per port, is now 32 VFs per port) - Support for next generation 10GbaseT PHY - Expose IBM Feature On Demand licensing information in UEFI configuration utility
Known Issues: - All 10Gb ports must be used with 10Gb switches. They will not link at 1Gb. - IPv6 IP address not visible via IMM GUI for IBM Option 90Y6456 - Intermittent link status with IBM Virtual Fabric Switch when set to IBM Virtual Fabric Mode - The option to enable/disable SRIOV on HS23 LOM Port 0 is missing from OneCommand Manager. This selection is available in UEFI F1 setup.
Firmware Version: 4.1.455.6 Supported On: IBM System x and BladeCenter
Problems Fixed: - Fixed an issue where ASIC randomly hangs losing network connectivity when certain commands are sent from the host. Resulting behavior varies between OS's (Yellow bangs in Windows, PSOD in VMWare) - PHY Loopback fails on 10G ports - UE and hang on LOM or Robalo when powering off Janice in UEFI or PXESelect - Loopback on HS23 now functional in DSAp - DCBX does not converge with firmware on a FCoE fabric - Control C Broken on BE2 - 7 second delay in GET_CARD_ATTRIBUTES command - Emulex VF adapter FCoE link lost on VMware 5.0 - flow control set for 10G Base T phys for autonegotiation - Dynamic link update is not working with NIC UEFI driver - Remove unused definitions in UEFI NIC - Emulex driver expects that the Login Options field be zero - "map r" displays a iSCSI BLK device when no LUNs presented - "X/x Exit without save" does not work as expected - Display proper description as part of EFI Driver Model Related Information - Intermittent "Configuration changed. reset to apply it now?" - Garbled output being displayed at the LUN configuration section. - All Emulex Configuration settings get lost after a reset - Perform additional checks when no Luns are mapped to the target - CHAP name only accepts 6 to 10 characters - Hii ???iSCSI Initiator Configuration??? showing old version screen - iSCSI name is case sensitive - iSCSI HII allows user to select first 8 LUNs as bootable. - iSCSI Boot Enable/Disable option should be port specific - LUN Configuration shows LUN 0, even if no LUNs presented to initiator.
Interoperability Since Previous Release: - Support for Emulex Virtual Fabric Adapter Advanced (CFFh, 2+2) for IBM BladeCenter
Firmware Version: 4.1.334.47 Supported On: IBM System x and BladeCenter
Problems Fixed: - NCSI transmit workaround for IBM - Issues with data reporting when BOFM enabled - Improved network performance throughput - Issues with IBM Management network performance - Logical link status for IBM mezz card shown as 'N/A' - Serial Over LAN fails when more than one blade installed with a single switch - Removed UEFI menu items for unsupported functions on a port - Issues with diagnositics in virtual NIC/UMC mode - Issues with MAC and PHY loopback on OneConnect devices - Several issues with FCoE on some OEM fabric switches
Interoperability Since Previous Release: - Support for HS23 Virtual Fabric LAN on Motherboard - Support for VFA III (95Y3762, 95Y3768), 90Y6456 - Support for IBM's Features on Demand (FOD) - Formal support for SR-IOV
Firmware Version: 4.0.1062.0 Supported On: IBM System x and BladeCenter
Problems Fixed: - iLab Tucson - lpfc Device Resets and path failures continue after error inject. - Writes do not complete when running LIP test on BE3 port 2 - IPV6 implementations no longer experience an unrecognized routing type error. - VLAN tagging is now disabled on the OneConnect UCNA when multichannel is disabled. - UEFI/BIOS-assigned LPVIDs now function properly on the OneConnect 10102-based UCNA. - OneConnect UCNAs no longer send and receive only double-tagged packets and discard all other packets. - PHY, MAC, and External loopback tests no longer fail on all platforms. - Firmware now returns the proper OneConnect UCNA model number. - IPV6 implementations no longer experience an unrecognized routing type error. - Installing Windows 2008 or Windows 2008 R2 on remote iSCSI disks no longer causes the system to hang. - Issues no longer occur when resetting a server configured for multipathing on VMware ESX systems. - VLAN tagging is now disabled on the OneConnect UCNA when multichannel is disabled. - UEFI/BIOS-assigned LPVIDs now function properly on the OneConnect 10102-based UCNA. - OneConnect UCNAs no longer send and receive only double-tagged packets and discard all other packets. - An adapter hardware error no longer occurs when running I/O with LUNs on x86 platforms. - Changing from Convergence Enhanced Ethernet (CEE) to Chassis Internal Network (CIN) and then rebooting no longer fails to link-flap (CIN Fabric Login (FLOGI) now occurs). - PHY, MAC, and External loopback tests no longer fail on all platforms. - Firmware now returns the proper OneConnect UCNA model number. - DCB settings can now be configured. - (iSCSISelect) When enabling DHCP for an iSCSI initiator, the Emulex iSCSI Network Configuration utility now waits approximately 20 seconds to make a DHCP connection before returning control. - (FCoE BootBIOS) FCF CEE parameters for Boot from SAN configuration are now saved properly.
Interoperability Since Previous Release: - Added support for switch-independent multichannel mode. - Added support for IBM Virtual Fabric 10Gb RackSwitch firmware 6.8.1.0. - Added support for IBM Virtual Fabric 10G Switch Module firmware 6.8.1.0. - Added support for Fibre Channel over Ethernet (FCoE) on rack systems. - Added support for iSCSI hardware offload on rack systems. - Added support for Cisco Nexus 5000-series switches.
IBM SAS Hard Disk Drive Update Program Version 1.13.02 Critical Release Reference RETAIN H207993 & H21743
This package includes new updates to drives with product ID strings of:
SAS 3.5"
- ST1000NM0023, ST2000NM0023,ST3000NM0023,ST4000NM0023 to BC55 Initial Code Release
- HUS723020ALS64 to J3K7 Additions to VPD information used by manufacturing and fixes for overall robustness.
- HUS723030ALS64 to J3K7 Initial Code Release
- ST31000424SS, ST32000444SS to BC2D - ST1000NM0001, ST2000NM0001 to BC49 Fixes for overall robustness.
- ST33000650SS to BC3E Initial Code Release
SAS 2.5"
- HUC109030CSS600, HUC109060CSS600, HUC109090CSS600 to J2E7 Initial Code Release.
- MK1401GRRB, MK3001GRRB to SC29 Fixes for overall robustness.
- MBF2300RC, MBF2600RC to SB2C Initial Code Release.
- ST9300605SS, ST9600205SS, ST9900805SS to B55D ST9146853SS, ST9300653SS to B63B ST9500620SS, ST91000640SS to BD2E ST9300505SS, ST9600105SS, ST9900705SS to E557 ST9146753SS to E636 Additions to VPD information used by manufacturing and fixes for overall robustness.
SATA 3.5"
- ST3500514NS, ST31000524NS, ST32000644NS to BB2C Reliability improvements, Additions to VPD information used by manufacturing
- HUA723020ALA640 to MK7OA930; HUA723030ALA640 to MKAOA930 Under certain heavy workloads the drive may incorrectly attempt to merge write commands. It willl shut itself down when it detects the mistake. The resulting command time outs will result in the drive being marked off line.
SATA 2.5"
- TE22D10100GE8IBM to SR3B Initial Code Release
- MTFDDAK064MAR-1J1AA, MTFDDAK128MAR-1J1AA, MTFDDAK256MAR-1K1AA, MTFDDAK512MAR-1K1AA to MA55 Initial Code Release
- ST9250610NS, ST9500620NS, ST91000640NS to BE28 Fixes for overall robustness.
SATA 1.8"
- MTFDDAA064MAR-1J1AB, MTFDDAA128MAR-1J1AB, MTFDDAA256MAR-1K1AB, MTFDDAA512MAR-1K1AB to MA55 Initial Code Release
- TX21B10100GE8IBM, TX21B10200GE8IBM, TX21B10400GE8IBM to SP3A Initial Code Release
Version 1.12.01 Critical Release Reference RETAIN #H207740
This package includes new updates to drives with product ID strings of:
SAS 3.5"
- VPCA300900EST1, VPCA450900EST1, VPCA600900EST1 to A3C4, Corrects firmware bug that may cause data corruption. For further information, please refer to Retain Tip H207740.
- ST3300657SS, ST3450857SS, ST3600057SS to BA5A VPCA300900EST1, VPCA600900EST1 to A3C2 Additions to VPD information used by manufacturing
- ST3750630SS, ST31000640SS to BC1I ST31000424SS, ST32000444SS to BC2C Mode Page change to address performance issues under certain system configurations
- ST33000650SS to BC3D ST1000NM0001, ST2000NM0001 to BC48 Protection Information Fix - see Retain Tip H206140
- HUS723020ALS64, HUS723030ALS64 to J26C Initial Code Release
SAS 2.5"
- ST9300603SS, ST9146803SS to B53E ST9600204SS to B549 Additions to VPD information used by manufacturing
- ST9300605SS, ST9600205SS, ST9900805SS to B55C ST9146853SS, ST9300653SS to B63A ST9500620SS, ST91000640SS to BD2C ST9300505SS to E555 ST9146753SS to E635 Protection Information Fix - see Retain Tip H206140
- ST9600105SS, ST9900705SS to E555 Inital Code Release
- HUC106030CSS60, HUC106060CSS60 to D3A6 Performance improvements, critical fixes for Protection Information (PI) operation - see Retain Tip H206140
- MK1401GRRB, MK3001GRRB to SC27 Additions to VPD information used by manufacturing
- WD9001BKHG-23D, WD6001BKHG-23D, WD3001BKHG-23D to ZA31 Initial Code Release
SATA 3.5"
- WD2502ABYS-23B7A0 to 02.03B08 WD1602ABYS-23B7A0 to 02.03B07 Critical fix to address premature drive failures.
- ST3500514NS, ST31000524NS, ST32000644NS to BB2A ST33000650NS to BB38 ST1000NM0011, ST2000NM0011, ST500NM0011 to BB47 Fixes a potential, but rare data corruption issue which requires a background reallocation that exceeds the error recovery timer.
- HUA723020ALA640 to MK70A900 HUA723030ALA640 to MKA0A900 Initial Code Release
SATA 2.5"
- ST9160511NS, ST9500530NS to BE1A ST9250610NS, ST9500620NS, ST91000640NS to BE25 Fixes a potential, but rare data corruption issue which requires a background reallocation that exceeds the error recovery timer.
SSD
- TX21B10200GE1IBM, TX21B10400GE1IBM, TX21B10100GE8IBM to PRO6SP36 TE22D10100GE8IBM to PRO6SR36 Initial Code Release
- MTFDDAK128MAR-1J1AA, MTFDDAK256MAR-1K1AA to MA52 Initial Code Release
- MTFDDAA512MAR-1K1AB, MTFDDAK064MAR-1J1AA, MTFDDAK512MAR-1K1AA, MTFDDAA064MAR-1K1AB, MTFDDAA128MAR-1K1AB, MTFDDAA256MAR-1K1AB to MA52 Fixes SMART attribute 190 (Current Temp) which caused warning messages with some versions of Linux
- STEC MACH8 IOPS to 2804 STEC M8PSB2 T4 to SM06 Additions to VPD information used by manufacturing Fixes potential drive failure if power loss occurs during firmware update.
*******************************************
Version 1.11.01 (Non-Critical) - Fixed issue where hard disk drives may not be detected in configurations with multiple Emulex adapters.
See Verion 1.11 for Hard Disk Drive support, firmware levels, and respective change History.
- ST33000650SS to BC3A ST1000NM0001, ST2000NM0001 to BC44 Additions and corrections to VPD information used by manufacturing
SAS 2.5"
- ST9300605SS, ST9600205SS, ST9900805SS to B559 ST9146853SS, ST9300653SS to B637 ST9500620SS, ST91000640SS to BD29 ST9300505SS to E553 SST9146753SS to E633 HUC106030CSS60, HUC106060CSS60 to D390 Additions and corrections to VPD information used by manufacturing
- MK1401GRRB, MK3001GRRB to SC23 Fixes a pottential data corruption bug if there is an unexpected power loss.
SATA 3.5"
- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB15 ST3500514NS, ST31000524NS, ST32000644NS to BB29 ST33000650NS to BB36 ST1000NM0011, ST2000NM0011, ST500NM0011 to BB46
SATA SSD
- SG9XCS1B50GMIBM, SG9XCS1F200GEIBM to SA03SB6C SG9XCS2D200GEIBM to SA03SE6C Fix for potential hang during an unexpected power cycle
MTFDDAK128MAR-1JAAB, MTFDDAK256MAR-1JAAB to MA44 Initial Release
=========================================== Version 1.10 (Critical)
This package includes new updates to drives with product ID strings of:
SAS 3.5"
- VPCA300900EST1, VPCA600900EST1 to A3C0 Correction to VPD information used by manufacturing
- ST31000424SS, ST32000444SS to BC2B Fixes to improve robustness from certain read errors due to encroachment
- ST33000650SS to BC37 Fixes to improve overall robustness.
- ST1000NM0001, ST2000NM0001 to BC42 Inital Release
SAS 2.5" (SFF)
- ST9300605SS, ST9600205SS, ST9900805SS to B556 - ST9146853SS, ST9300653SS to B635 Fixes to improve overall robustness.
ST9300505SS to E552 ST9146753SS to E632 Initial Release
- ST9500620SS, ST91000640SS to BD26 Improve general robustness and added support for DPICZ
- HUC106030CSS60, HUC106060CSS60 to D340 Improve general robustness
- MBF2300RC, MBF2600RC to SB28 Improves performance in certain benchmarks
SATA 3.5"
- ST33000650NS to BB34 Fixes to improve overall robustness.
- ST1000NM0011, ST2000NM0011, ST500NM0011 to BB45 Initial Release
- ST3500514NS, ST31000524NS, ST32000644NS to BB29 Fixes for intermittent drive hangs
- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB15 Added enhancement for improved robustness
SATA 2.5"
- ST9250610NS, ST9500620NS, ST91000640NS to BE24 Initial Release
- ST9160511NS, ST9500530NS to BE19 Fixes for overall robustness.
SATA 2.5" SSD
- STEC MACH8 IOPS to 2765 STEC M8PSB2 T4 to SM05 Fixes potential drive lock up during cold or warm boots Fixes issues with RHEL 6.x installation
- SG9XCS2D200GEIBM to SA03SE6C Fixes default drive VPD information for manufacturing, the default LED behavior on certain systems and fixes issues with client install thru VMWare 5.x
SATA 1.8" SSD
- STEC M8PSB1 to 0409 STEC M8PSB1 T4 to SM16 Fixes potential drive lock up during cold or warm boots Fixes issues with RHEL 6.x installation
- SG9XCS1B50GMIBM to SA03SB6C SASG9XCS1F200GEIBM to SA03SB6C Fixes potential drive lock up during cold or warm boots and the default LED behavior on certain systems and fixes issues with client install thru VMWare 5.x
=========================================== Version 1.09 (Critical)
This package includes new updates to drives with product ID strings of:
SAS 3.5"
- ST31000424SS, ST32000444SS to BC28 Added enhancement for improved RV robustness
- MBE2073RC, MBE2147RC to SC17 - MBA3073RC, MBA3147RC, MBA3300RC to SA0A Added VPD changes for manufacturing
SAS 2.5" (SFF)
- ST9300603SS, ST9146803SS to B53C ST9600204SS to B548 SST973452SS, ST9146852SS to B62C CBRCA146C3ETS0, CBRCA300C3ETS0 to C610 Added fixes for overall drive robustness
- MBD2147RC, MBD2300RC to SB1A Added VPD changes for manufacturing Addresses issues seen with DSA HDD Diagnostic test.
- MBF2300RC, MBF2600RC to SB25 Addresses issues seen with DSA HDD Diagnostic test.
- ST9500620SS, ST91000640SS to BD22 HUC106030CSS60, HUC106060CSS60 to D2F8 Inital Release
SATA 3.5"
- WD2502ABYS-23B7A0 , WD1602ABYS-23B7A0 to 02.03B07 Addresses firmware issues that may cause a drive to be marked defunct prematurely under certain application workloads.
- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB14 ST3500514NS, ST31000524NS, ST32000644NS to BB28 Added enhancement for improved robustness
- WD5003ABYX-23 to WC31 Initial Release
SATA 2.5"
- WD3000BLFS-23YBU0 to 04.04V10 (Critical) Addresses firmware issues that may cause a drive to be marked defunct prematurely under certain application workloads.
- ST9250610NS, ST9500620NS, ST91000640NS to BE21 Initial Release
SATA 2.5" SSD
- STEC MAC8 IOPS to 2732 STEC M8PSB2 T4 to SM04 Addresses an issue installing RHEL 6.0 onto this drive.
SATA 1.8" SSD
- SG9XCS1B50GMIBM, SG9XCS1F200GEIBM to SA03SB63 Addresses rare issue where the drive may not being seen on power up.
- STEC M8PSB1 to 0408 STEC M8PSB1 T4 to SM15 Addresses an issue installing RHEL 6.0 onto this drive.
- ST373455SS, ST3146855SS, ST3300655SS to BA2D - ST373355SS, ST3146755SS, ST3300555SS to BA38 - ST3146356SS, ST3300656SS, ST3450856SS to BA4C - ST3300657SS, ST3450757SS, ST3600057SS to BA58 - ST3750630SS, ST31000640SS to BC1G - ST31000424SS, ST32000444SS to BC26 (All Above Critical) These codes addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. For further information, please refer to retain tip H197382.
- MBA3073RC, MBA3147RC, MBA3300RC to SA08 This code corrects a firmware bug that may cause the drive to not come ready on a cold boot.
SAS 2.5" (SFF)
- ST973402SS, ST9146802SS to B52B - ST936751SS, ST973451SS to B617 - ST9600204SS to B546 - ST973452SS, ST9146852SS to B629 - ST9300503SS to E536 - ST9146752SS to E625 - ST9500430SS to BD14 (All Above Critical) These codes addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. For further information, please refer to retain tip H197382.
SATA 3.5"
- ST3500514NS, ST31000524NS, ST32000644NS to BB26
- WD2003FYYS-23W0B0 to WA32 - WDC WD1003FBYX-23Y7B0 to WB31 Initial release
SATA 2.5" SSD
- STEC MACH8 IOPS to 2582 (Critical) Corrects firmware bug that may cause data corruption. For further information, please refer to retain tip H197650.
SATA 1.8" SSD
- STEC M8PSB1 to 0405 (Critical) Corrects firmware bug that may cause data corruption. For further information, please refer to retain tip H197650.
This package includes new updates to drives with product ID strings of:
SAS 3.5"
- VPCA300900EST1, VPCA450900EST, VPCA600900EST1 to A3B8 Initial Release
- VPBPA300C3EST1 to A529 Initial Release
- ST3300657SS, ST3450757SS, ST3600057SS to BA56 (Critical) Performance improvements under certain workloads. Corrects a firmware bug that may cause the drive to not come ready on a warm or cold reboot.
- ST31000424SS, ST32000444SS to BC21 Initial Release
SAS 2.5" (SFF)
- ST9300603SS, ST9146803SS to B53A (Critical) Performance improvements under certain workloads. Corrects a firmware bug that may cause the drive to not come ready on a warm or cold reboot.
- ST9600204SS to B544 (Critical) Corrects a firmware bug that may cause the drive to not come ready on a warm or cold reboot.
- ST973452SS, ST9146852SS to B626 Performance improvements under certain workloads.
- ST9500430SS to BD13 Performance improvements under certain workloads
- ST9300503SS to E534 and ST9146752SS to E623 Performance improvements under certain workloads.
- MBD2147RC, MBD2300RC to SB19 (Critical) Retain Tip H196899 MBE2073RC, MBE2147RC to SC16 (Critical) Retain Tip H196899 Corrects a firmware bug that erroneously reported medium errors which may cause the drive to report PFA alerts and in some cases be marked offline
SATA 3.5"
- WDC WD2502ABYS-23B7A0, WD2502ABYS-23B7A0, WD802ABYS-23B7A0, WD1602ABYS-23B7A0 to 02.03B05 (Critical) Corrects a firmware bug that may cause the drive to not come ready on a warm or cold reboot.
- ST3500514NS, ST31000524NS, ST32000544NS to BB26 (Critical) This code addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. For further information, please refer to retain tip H197382.
- ST3250310NS, ST3500320NS, ST3750330NS, ST31000340NS to BB13 (Critical) This code addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. For further information, please refer to retain tip H197382.
- HUA722020ALA330 to JKAOA3GA HUA722050CLA330 to JP2OA3GB HUA722010CLA330 to JP4OA3GB Initial Release
SATA 2.5"
- WD3000BLFS-23YBU0 to 04.04V09 (Critical) This code corrects an additional issue where the drive may be marked defunct.
- ST9160511NS, ST9500530NS to BE18 (Critical) This code addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. For further information, please refer to retain tip H197382. Also improves performance under certain workloads.
SATA 2.5" SSD
- STEC MACH8 IOPS to 2366 (critical) Corrects firmware bug that may cause degraded performance and in some cases the drive may not come ready after a warm or old boot.
SATA 1.8" SSD
- STEC M8PSB1 to 0404 Turns the default for write cache off
*******************************************
Version 1.06 (Critical)
Added support for the following controllers:
- IBM ServeRAID BR10il SAS controller v2 (49Y4731) - IBM ServeRAID M1015 SAS controller (46M0831) - IBM ServeRAID M5015 SAS controller (46M0829) - IBM ServeRAID M5014 SAS controller (46M0916)
The following is a list of drives and the firmware that they will be checked for and updated to as necessary.
This package includes new updates to drives with product ID strings of:
SAS 3.5" --------------
- ST373455SS, ST3146855SS, ST3300655SS to BA2A ST373355SS, ST3146755SS, ST3300555SS to BA36 (Critical) This code addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. When a write is issued while the drive write cache is enabled and a read-verify is performed immediately afterwards, undetected data corruption can occur. For further information, please refer to retain tip H194632.
- ST3750630SS, ST31000640SS to BC1E ST3146356SS, ST3300656SS, ST3450856SS to BA4A This code address an issue where the drive may report an erroneous hardware error to the controller.
- MBA3073RC, MBA3147RC, MBA3300RC to SA07 This code improves sequential write performance under certain workloads when write cache is turned on.
- ST3300657SS, ST3450757SS, ST3600057SS to BA52 NOTE: This is the first code release to be included in the hard drive update package.
SAS 2.5" (SFF)
- ST973402SS, ST9146802SS to B52A ST936751SS, ST973451SS to B616 (Critical) These codes addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. When a write is issued while the drive write cache is enabled and a read-verify is performed immediately afterwards, undetected data corruption can occur. For further information, please refer to retain tip H194632.
- MBB2073RC, MBB2147RC to SB07 MBD2147RC, MBD2300RC to SB17 MBE2073RC, MBE2147RC to SC14 CBRCA146C3ETS0, CBRCA300C3ETS0 to C370 This code improves sequential write performance under certain workloads when write cache is turned on.
- ST9500430SS to BD11 This is the first code release to be included in the hard drive update package.
SATA 3.5"
- WD2003FYYS-23T8B0 to 01.00D04 This is the first code releases to be included in the hard drive update package.
SATA 2.5"
- WD3000BLFS-23YBU0 to 04.04V08 (Critical) This code corrects an issue where the drive may generate a false PFA alert. It also corrects an issue where the drive may be marked defunct
- ST9160511NS, ST9500530NS to BE16 This is the first code releases to be included in the hard drive update package.
*******************************************
Version 1.05
The following is a list of drives and the firmware that they will be checked for and updated to as necessary.
This package includes new updates to drives with product ID strings of:
SAS 2.5" (SFF) -------------- ST9xxxx51SS to B616 ST9xxxx02SS to B52A - This code improves the robustness of write cache operations.
ST9xxxx52SS to B624 ST9xxxx03SS to B536 - This code improves the robustness of write cache operations and sequential write performance when write cache is enabled. NOTE: This is the first code for the ST9xxxx52SS and ST9xxxx02SS drives to be included in a hard drive update package. It is an update from the code that is shipped with the drive.
MBD2xxxRC to SB14 - Initial release
SAS 3.5" -------- ST3xxxxx6SS to BA49 ST3750630SS to BC1D - This code improves the robustness of write cache operations.
SATA 2.5" --------- WD3000xxxxx to 04.04V05 - Adjusted PHY setting for better signal quality margin.
SATA 2.5" SSD -------------- STEC MACH8 IOPS to 2269 GBRL0xxxxx to 4.17 GBRLBxxxxx to 4.26 - The new firmware will correct a rare data error condition in the drives where invalid data may be passed to the system without any error condition flagged.
Due to the severity of this potential issue, IBM strongly recommends applying this firmware as soon as possible.
For further information, please refer to retain tip H195663.
NOTE: This is the first code for the GBRLBxxxxx drives to be included in a hard drive update package. It is an update from the code that is shipped with the drive.
*******************************************
Version 1.04
The following is a list of drives and the firmware that they will be checked for and updated as necessary.
This package includes new updates to drives with product ID strings of:
SAS 2.5" (SFF) -------------- CBRBAxxxxxx to C49B - Modified VPD for JSxx Blades
MBBxxxxxx to SB05 - Fixed a performance issue when synchronizing or rebuilding an array when used in a LSI 1064 based SAS controller.
MBC2073RC to SC04 - Fixed a performance issue when synchronizing or rebuilding an array when used in a LSI 1064 based SAS controller.
SAS 3.5" -------- MBAxxxxxx to SA06 - Fixed a performance issue when synchronizing or rebuilding an array when used in a LSI 1064 based SAS controller.
ST3xxxxx6SS to BA48 - This code addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. When a write is issued while the drive write cache is enabled and a read-verify is performed immediately afterwards, undetected data corruption can occur. For further information, please refer to retain tip H194632.
ST3750630SS to BC1A - This code addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. When a write is issued while the drive write cache is enabled and a read-verify is performed immediately afterwards, undetected data corruption can occur. For further information, please refer to retain tip H194632. - Fixes a hang condition during failover operation on a BladeCenter-S chassis with an RSSM controller.
BBAxxxxxx to BH0K - Fixed an issue where a drive may prematurely report a PFA trip.
GNAxxxxxx to BH0J - Fixed an issue where a drive may prematurely report a PFA trip.
SATA 3.5" --------- ST31000340NS, ST370330NS, ST3250310NS, ST3500320NS to BB12 - This code addresses a rare potential for data corruption. For this issue to occur, the drive write cache must be enabled. When a write is issued while the drive write cache is enabled and a read-verify is performed immediately afterwards, undetected data corruption can occur. For further information, please refer to retain tip H194632. - This code addresses a rare potential for data loss. After a power cycle, the drive will no longer be available and becomes unresponsive. Data will become inaccessible due to the drive not responding. For further information, please refer to retain tip H194623.
WDC WD2502ABYSxxxxx to 02.03B04 - Fixed incorrect VPD data.
SATA 2.5" --------- WD3000xxxxx to 04.04V04 - Fixed a Critical issue - IBM recommends a backup of the data on the drive before attempting to update the firmware. This is a fix for an issue where data required for spin up of the drive may be overwritten, rendering the drive inoperable on a subsequent warm or cold system reboot. - Fixed a bug with an internal timer that may cause a drive to go offline when used in a non-RAID environment.
SATA 2.5" SSD ------------- STEC MACH8 IOPS to 2103 - Initial Release
*******************************************
Version 1.03
Added the capability to update SAS and SATA drives online under Windows or Linux. This capability is only supported if the drives are attached to one of the following SAS adapters: - IBM ServeRAID MR10k SAS Controller - IBM ServeRAID MR10i SAS Controller - IBM ServeRAID MR10M SAS Controller - IBM ServeRAID MR10il SAS Controller - IBM ServeRAID MR10is SAS Controller - MegaRAID 8480 SAS Controller - IBM ServeRAID BR10i SAS Controller - IBM ServeRAID BR10il SAS/SATA Controller - IBM SAS HBA - IBM SAS Expansion Card (CFFv) for IBM BladeCenter - IBM SAS Connectivity Card (CFFv) for IBM BladeCenter - Onboard LSI 1064 SAS controller (2MB only) - Onboard LSI 1068 SAS controller - Onboard LSI 1078 SAS controller
This package includes new updates to drives with product ID strings of:
SAS 2.5" (SFF) -------------- ST9146802SS, ST973402SS to B529 - Added support for JS2x Blades in a BladeCenter-S chassis. - Picked up the latest network roll of firmware fixes to address some unexpected system hangs.
ST936751SS, ST973451SS to B615 - Added support for JS2x Blades in a BladeCenter-S chassis. - Picked up the latest network roll of firmware fixes to address some unexpected system hangs.
CBRBAxxxxxx to C495 - Initial release
MBBxxxxxx to SB04 - Initial release
MBC2073RC to SC03 - Initial release
SAS 3.5" -------- VPBAxxxxxx to A496 - Added support for JS2x Blades in a BladeCenter-S chassis.
ST3146855SS, ST3300655SS, ST373455SS to BA29 - Added support for JS2x Blades in a BladeCenter-S chassis. - Picked up the latest network roll of firmware fixes to address some unexpected system hangs.
ST3450856SS to BA47 - IBM was notified by our vendor that there is a defect in a level of firmware used in the IBM 450GB 15K SAS 3.5" HS HDD (PN 41Y8454) in option 42D0519, which under certain conditions may lead to data being written or read back incorrectly on the drive. IBM has worked closely with the vendor to identify the problem and developed a firmware fix to resolve the problem. Customers should upgrade to firmware level BA47.
MBAxxxxxx to SA05 - Initial release
ST3750630SS to BC17 - Initial release
SATA 3.5" --------- ST3250620NS, ST3500630NS, ST3750640NS to 3.AEV - Initial release
ST3250621NS, ST3500631NS, ST3750641NS to 4AEV - Initial release
ST31000340NS, ST3750330NS, ST3250310NS, ST3500320NS to BB10 - Initial release
HUA721050KLA330, HUA721075KLA330, HUA721010KLA330, to AB4A - Initial Release
SATA 2.5" SSD ------------- GBRL001xxx, GBRL0031xxx to 4.14 - Corrects intermittent hangs during operations.
Integrated Management Module II (IMM2) Firmware Update Change History
Version 3.82, 1AOO56E - Critical Fix for x3850 X6 / x3950 X6 -- Updated the firmware with patches to address the 'Heartbleed' OpenSSL bug (CVE-2014-0160)
Version 3.73, 1AOO56D - Critical Fix for dx360 M4, x3650 M4, x3550 M4, x3500 M4, x3100 M4, x3250 M4, x3750 M4 -- Updated the firmware with patches to address the 'Heartbleed' OpenSSL bug (CVE-2014-0160)
Version 3.71, 1AOO52W - Critical Fix for x3550 M4: -- Fixed a potential security vulnerability with information contained in service data (refer to security bulletin CVE-2014-0882) -- Fixed a problem system may shut down with new Mezz card installed
Version 3.70, 1AOO52Q - Critical Fix: -- Fixed a potential security vulnerability with information contained in service data (refer to security bulletin CVE-2014-0882)
Version 3.67, 1AOO50G - Supports System x3650 M4 BD, Machine Type: 5466
Version 3.65, 1AOO50D NOTE: If you have a System x3550 M4 with the "Emulex VFA Mezz card" and a ==== single processor, don't update the IMM2 with this firmware - Critical Fix: -- Fixed a problem on the System x3650 M4 server where the system shuts down due to a false temperature event from the ambient temperature sensor - Fixed a problem where the IMM2 may erroneously report a fan fault in the x3630 M4 when the system is powering on. See RETAIN tip H207461 for the description of the original problem - Fixed a screen refresh problem where it occurs after resetting IMM2 - Fixed a firmware problem that may cause the IMM2 to reset unexpectedly - Fixed a problem where the IMM2 SNMP interface may intermittently be unavailable if the system is running VMWARE ESXi 5.x - Fixed a problem where the CPU may potentially throttle in the x3650 M4 system with two 550 watt power supplies and one hard drive backplane
Version 3.60, 1AOO50C - Added support for the Intel IvyBridge-EP CPU on the HS23 blade - Fixed a problem where the HS23 hard drive number reported in the AMM event did not match the drive number on the physical blade enclosure - Fixed an intermittent problem where the UXSPI update utility may erroneously report that the firmware image is not meant for the HS23 system - Fixed a problem that causes the AMM web interface to not display properly when drives are removed or inserted - Fixed a problem where the IMM2 may not detect an over temperature condition for a DIMM
Version 3.56, 1AOO50K - Fixed a Flex Systems Manager (FSM) Configuration Patterns problem where configuration deployments would fail with an activation job error message: ERROR: LDAP failed with rc=102 ERROR: LDAP failure: SYSPROF_LDAP_BIND_FAIL INFO
Version 3.55, 1AOO50E - Fixed an issue so a fully qualified domain name can be used for a syslog collector in addition to an IP address - Fixed an issue to allow a user the ability to specify the port to use for syslog notifications, rather than only supporting the default port
Version 3.50, 1AOO50B - Fixed an issue where the default static IPv4 address was assigned to the IMM2 management interface instead of the user configured static IPv4 address in DHCP fallback to static mode, if the DHCP server was not available - Prevent a VLAN from being configured on the IMM2 management interface for Flex nodes - Fixed a problem where the CPU throttling state recovery indication to the FSM might not be properly reported - Corrected an issue with the launch of the IMM2 Remote Console operation that required a restart of the IMM2 - Corrected the firmware to apply the inactivity timeout to web pages that automatically refresh - Updated the web browser support. The following web browsers are supported: Firefox 3.6-20 Chrome 13-26 Internet Explorer 8-10 - Added support for the S3 Sleeping State to the IMM2 user interfaces on those servers that include the S3 feature - Added changes to use the minimum TLS version setting that is provisioned by the CMM in Flex for encrypted communication - Enhanced the content of the service data file to assist in problem determination - Added a option to have the IMM2 automatically copy the firmware from its primary bank into the backup bank after the firmware has been run for a period of time and proven itself to be stable - Enhanced the IMM2 firmware to automatically restore itself without the need for user intervention if the firmware becomes corrupted - Added new commands on the command line interface to stop a serial redirection operation that is currently in progress, and to report the user names that have a serial redirection operation started - Added changes to use the DNS settings that are provisioned by the CMM in Flex to support use of an LDAP hostname for authentication - Updated the firmware to log hardware inventory change informational messages - Added support for the Service Advisor feature on stand alone rack servers to automatically call for service when a repair is needed - Added support to configure the Ethernet-over-USB IP address using ASU - Added changes to support the thermal requirements for new Solid State Drives used with the ServeRAID M5100 Series IBM Flex System Flash Kit v2 - Updated the IMM2 date and time web page on Flex nodes to only display the current date and time - Updated the SSH firmware to address various OpenSSH vulnerabilities that have been identified by security community - Added changes to support the Web Services-Management protocol
Version 3.40, 1AOO48M - Supports System x3250 M5, Machine Type: 5458
Version 3.37, 1AOO48P - Added support for the IBM NeXtScale Storage Native Expansion (NeX) Tray for IBM NeXtScale nx360 M4
Version 3.36, 1AOO48Q - Fixed a problem on System x iDataPlex dx360M4 where a CIM client cannot get needed event information for asserted events
Version 3.35, 1AOO48N - Critical Fix: -- Corrected a problem on the System x3650 M4 and x3650 M4 HD servers causing the system to shut down due to an erroneous critical temperature event reported by the ambient temperature sensor
Version 3.30, 1AOO48L - Fixed a problem on System x iDataPlex dx360M4 where nodes shutdown due to a critical temperature event from the Ambient Temp sensor
Version 3.20, 1AOO48K - Supports System NeXtScale nx360 M4, Machine Type: 5455
Version 3.10, 1AOO48H - Added support for System x3650 M4 HD, Machine Type 5460 - Added support for newer CPUs in the System x iDataPlex dx360M4, x3500M4, x3550M4, and x3650M4 servers - Added a feature on the System x3550 M4 and x3650 M4 to fail over from the dedicated systems management network port to the shared port when the dedicated network link is not available - Fixed a problem where an NTP update message is logged every 1440 minutes - Fixed a problem where the IMM2 web interface won't accept an NTP hostname string that starts with a numeric character - Fixed a problem where the LDAP Group Filter authentication does not work as expected - Fixed a problem where the IMM2 reports 0 Watts when the System x iDataPlex dx360M4 is DC cycled or resumes from the S3 sleep state - Fixed an Ethernet problem that may cause an IMM2 failure to establish a link when the Ethernet speed and duplex settings are not configured to use auto-negotiation
Version 2.60, 1AOO42Y NOTE: For increased security, only high strength ciphers are now supported when using https.
==== Your browser must support one of the following cipher suites: | HE-RSA-AES256-SHA256 TLSv1.2 Kx=DH Au=RSA Enc=AES(256) Mac=SHA256 DHE-RSA-AES256-SHA SSLv3 Kx=DH Au=RSA Enc=AES(256) Mac=SHA1 AES256-SHA256 TLSv1.2 Kx=RSA Au=RSA Enc=AES(256) Mac=SHA256 AES256-SHA SSLv3 Kx=RSA Au=RSA Enc=AES(256) Mac=SHA1 DHE-RSA-AES128-SHA25 TLSv1.2 Kx=DH Au=RSA Enc=AES(128) Mac=SHA256 DHE-RSA-AES128-SHA SSLv3 Kx=DH Au=RSA Enc=AES(128) Mac=SHA1 AES128-SHA256 TLSv1.2 Kx=RSA Au=RSA Enc=AES(128) Mac=SHA256 AES128-SHA SSLv3 Kx=RSA Au=RSA Enc=AES(128) Mac=SHA1
- Added support for the IBM Flex System x222 Compute Node - Improved Remote Presence (keyboard, mouse and virtual media)and in-band management (LAN-over-USB) performance - Changed the default file name for the Service Data file (First Failure Data Capture or FFDC) on the web interface to incorporate the machine type, serial number and a timestamp - Updated the IMM2 PCIe Bridge Firmware to support Windows 2012 Certification - Improved IMM2 Reliability, Availability, Serviceability (RAS) Features: - Added component and system VPD integrity checking & reporting - Enhanced Service Data collection (FFDC)
- Enhanced the configuration of UEFI settings via the CIM interface for applications like IBM Systems Director - Added Sub-manufacturer inventory support for mezz card and Sub-manufacturer inventory support for the system for IBM Systems Director - Added the UUID for the PCIe Expansion Node and the Storage Expansion Node to the SLP attributes reported by the IMM2 - Added the number of enabled CPU core and the Static power savings mode support for IBM Systems Director - Enhanced the alert recipient email notification, firmware update, event log, log out, and hardware information web pages to improve usability - Added support for IPMI & SNMPv3 accounts to be centrally managed by the Flex Chassis Management Module - Fixed a problem where an invalid configuration was erroneously reported for an unpopulated CPU socket in the IBM Flex System x440 - Enabled users to configure a longer trespass message - Increased the length of the LDAP group filter field to 511 characters - Corrected a problem with ServeRAID M5115 SAS/SATA Controller for IBM Flex Systems energy pack monitoring - Corrected a problem with ServeRAID M5115 SAS/SATA Controller for IBM Flex Systems LED management - Added IPMI command to configure the LAN-over-USB IP address
Version 2.52, 1AOO42E - Critical Fix: -- Fixed a problem on the System x3300 M4 servers causing the system to shut down due to a critical temperature event reported by the ambient temperature sensor
Version 2.50, 1AOO40Z - Added support for the Solarflare SFN5162F MR Dual Port 10GbE SFP+ Adapter, and Solarflare SFN6122F LL Dual Port 10GbE SFP+ Adapter for System x3550 M4 and x3650 M4 NOTE: UEFI also needs to be upgraded to D7E128B (v 1.40 or newer, for the x3550 M4) or VVE128B (v1.40 or newer, for the x3650 M4) to support these cards - Added support for the Mellanox ConnectX-3 Dual Port QDR/FDR10 mezzanine card and Mellanox ConnectX-3 VPI Single-port QSFsorry.P FDR14/40GbE HCA on System x3550 M4, and x3650 M4 - Added optional Fan Zone support for single CPU systems (x3550 M4 and x3650 M4) with an installed with Qlogic Dual Port 10GbE SFP+ Embedded VFA - Fixed an intermittent problem where a Gratuitous ARP is not sent successfully - Fixed a problem where after the IMM2 firmware is flashed, there is a slight chance that the IMM2 web server can't be accessed when AC power is reapplied - Disabled the weak cipher suit used in the SSL/TLS firmware with the https protocol to avoid potential security vulnerabilities - Fixed a problem on the System x3750 M4 where the IMM2 shared mode network connection will be lost after upgrading the firmware of the onboard Emulex BE3 controller - Fixed a problem on the HS23 where the OS watchdog timer doesn't work - Fixed a problem on the HS23 where the Fault LED occasionally lights when the chassis is powered on with the BPE4 - Fixed a problem on the HS23 where the server may shut down after resetting the IMM2 - Enhanced the messaging mechanism between the BladeCenter AMM and the IMM2 - Added power management capability in the IMM2 web interface
Version 2.06, 1AOO42B - Corrected the firmware to prevent users from disabling the IPv6 interface - Fixed a problem that caused the IMM2 to reset itself after running for a period of time - Corrected the SNMP request to disable the IMM2 IPv4 interface so that it disables only IPV4, instead of both IPv4 and IPv6 - Fixed a problem that occasionally caused the server to shut down when the IMM2 is reset - Fixed a problem where the IMM2 incorrectly reported a battery voltage error - Corrected a problem where repeated frequent IMM2 resets causes the IMM2 to run the firmware in its backup partition - Corrected a problem report where the IMM2 did not report a failure to the system profiles script when the chassis UUID is unavailable
Version 2.00, 1AOO40E - Critical Fix: -- Improves the reliability of the CPU and/or memory VRDs. This improvement lowers the occurrence of CPU & memory VRD failures on the x3300 M4 and x3750 M4 -- IMM2 improved error reporting for missing/down CPU in invalid CPU configuration for x4440 M4 - Corrected a problem that caused 3.3V and 5V faults to be reported by IMM2 firmware level 1aoo34z(1.85) on the HS23E blade - Eagle Ray SAS controller LED fault support improvements added for all ITE platforms
Version 1.97, 1AOO36R - Critical Fix: -- Improves the reliability of the CPU and/or memory VRDs. This improvement lowers the occurrence of CPU & memory VRD failures on x3650 M4, x3550 M4 and x3500 M4 - Thermal behavior enhancement on System x iDataPlex dx360 M4
Version 1.95, 1AOO36P (for System x iDataPlex servers) - Added support for NVIDIA K1,K2,K20,K20x GPUs on System x iDataPlex dx360 M4
Version 1.88, 1AOO40A (for PureFlex System Compute Nodes) - Critical Fix: -- Fixed a potential security vulnerability with node management user accounts (Reference to Security Bulletin CVE-2012-4838) - Fixed a problem on Flex Systems where the SNMP get and set authority levels did not work - Fixed a problem on Flex Systems where mounting of remote media in a Linux environment showed a USB error - Fixed a problem on Flex Systems that caused the Remote Control Video Viewer window on a RHEL5.8 client to move when the arrow key is pressed - Fixed a problem on Flex Systems where the SMTP "Test Connection" button did not work when the SMTP port is changed - Fixed a problem on Flex Systems where the SNMP get and set authority levels did not work - Fixed a problem on Flex Systems where mounting of remote media in a Linux environment showed a USB error - Fixed a problem on Flex Systems that caused the Remote Control Video Viewer window on a RHEL5.8 client to move when the arrow key is pressed - Fixed a problem on Flex Systems where the SMTP "Test Connection" button did not work when the SMTP port is changed - Corrected the Mezzanine card power fault monitoring on the Flex System x440 Compute Node - Corrected a problem with IBM Fabric Manager configuration from the Flex Chassis Management Module - Added support to retrieve configuration settings from an LDAP server - Added support for the Flex Storage Expansion Node - Added support for CIM indications over https - Added fingerprint checking for SFTP transfers - Added automatic recovery of corrupted UEFI firmware - Added support for authenticated SMTP alerts - Added a display of the users who have a Remote Control session in progress - Provided a request to a Remote Control client to disconnect the session - Added support for the server S3 (sleep) state - Changed the default NTP sync interval from 3 minutes to 24 hours - Fixed a problem where the ambient temperature is only displayed in degrees Fahrenheit - Fixed a problem on the web interface where 'local' is not accepted as a top level domain name in the email format when configuring event recipients - Corrected an IMM2 SNMP trap OID to match the prior IMM format - Fixed a problem that prevented an external USB device from being remotely mounted as a floppy drive in Windows Server 2003 - Changed the blue Location led behavior to not blink when a firmware update is in progress
Version 1.85, 1AOO34Z (for BladeCenter blades and System x Servers) - Critical Fix: -- Fixed a potential security vulnerability with node management user accounts (Reference to Security Bulletin CVE-2012-4838) - Fixed a problem where a Blade Open Fabric Manager uncorrectable error can occur when booting the HS23 - Fixed a problem that IMM IPMI command periodically timed out when using HS23 in Chassis with the management network being disabled in some special configurations - Added support for the HS23 to recognize NEBS/Enterprise Mode for Telco chassis (this feature needs Advanced Management Module Firmware BPET62U or later) - Fixed a problem where the ambient temperature is only displayed in degrees Fahrenheit - Fixed a problem where on rack systems that have 2 power supplies installed, the 'Redundancy Power unit has been restored' event is logged every time that the IMM2 is reset - Fixed a problem where a Fan Tach going low (lower critical) event is intermittently asserted when configuring the IMM2 to use an NTP server - Fixed a problem on the web interface where 'local' is not accepted as a top level domain name in the email format when configuring event recipients - Corrected an IMM2 SNMP trap OID to match the prior IMM format - Fixed a problem that prevented an external USB device from being remotely mounted as a floppy drive in Windows Server 2003 - Changed the blue Location led behavior to not blink when a firmware update is in progress - Fixed a problem on the HS23E that causes Preboot DSA to hang in CLI mode when a user accesses it using Serial over LAN - Fixed a problem on rack servers where ASU cannot set IMM.GRP_GroupName.1 and IMM.GRP_GroupName.2 if the string length is 16 characters or longer. The firmware was corrected to allow a maximum length of 64 characters - Added support for CIM indications over https - Added fingerprint checking for SFTP transfers - Added automatic recovery of corrupted UEFI firmware - Added support for authenticated SMTP alerts - Added a display of the users who have a Remote Control session in progress - Provided a request to a Remote Control client to disconnect the session - Added support for the server S3 (sleep) state
Version 1.85, 1AOO34Y (for PureFlex System V7000 Storage Node) - Added support for Flex System V7000 Storage Node
Version 1.79, 1AOO36F - Thermal behavior enhancement on System x iDataPlex dx360 M4
Version 1.78, 1AOO36E - Thermal behavior enhancement for 115W & 95W CPU on System x iDataPlex dx360 M4 - Added support for the Intel KNC 5110p card
Version 1.77, 1AOO32X - Thermal behavior enhancement for 115W CPU on System x iDataPlex dx360 M4
Version 1.75, 1AOO32S - Fixed a problem that a PCI uncorrectable error occurs when using HS23 with CFFh card (44W4479) in the BCS chassis - Fixed a problem where an "Unsupported blade/blower combination" error is reported when using the HS23 in the BCHT chassis configured in Enterprise mode - Fixed a problem in System x3530 M4, where the reported Active Energy Manager input/output power readings are inaccurate - Fixed a problem in System x3530 M4, x3630 M4, where an LDAP account can not login using the AD_CrossDomain tree - Fixed a problem in System x3530 M4, x3630 M4, where a user cannot use the "DNS to Find LDAP server/Extract search domain from login ID" setting from the IMM2 web to access an eDirectory server - Added support for Common Form Factor power supplies Oversubscription in System x3750 M4, Machine Types: 8722, 8733
Version 1.65, 1AOO32O - Support the power supply Over-Subscription feature - Support the 750 Watt DC power supply for System x3650 M4,x3550 M4 - Support IBM 1.2TB High IOPS MLC Mono Adapter, IBM 2.4TB High IOPS MLC Duo Adapter for System x3650 M4, x3550 M4 - Support IBM LLM-SM Dual Port 10GbE SFP+ Adapter for System x3650 M4 - Fixed an abnormal Fan Zone recovery problem - Fixed a problem that IMM2 Email notification doesn't support an e-mail address with the underscore '_' character - Fixed a power policy "Restore" problem - Fixed a problem where the LDAP hostname can't be changed by ASU - Fixed a problem that the length of email address (for SNMP notification) is limited to 32 characters
Version 1.60, 1AOO32P - Fixed a problem where the Chassis Management Module cannot correctly get the Mezzanine card information for the Flex System x220 Compute Node - Fixed a problem where the PreBoot DSA firmware could not be updated under VMWare ESXi 5 through the Flex System Manager's Update Manager - Fixed a problem where an IMM2 communications error can occur if an unexpected response causes VMware to spawn multiple processes when it does not receive the data it expects from the IMM2
Version 1.59, 1AOO32K - Supports System x3300 M4, Machine Types: 7382
Version 1.53, 1AOO30Z - Included an update to the FPGA that fixes an intermittent issue where the CPUs do not show up in a system with a RAID card installed, when the AC is removed and reapplied from the server without allowing sufficient time for the system hardware to completely discharge
Version 1.52, 1AOO34A - Added redundant power supply and hot swap hard drive support in System x3100 M4
Version 1.51, 1AOO30Y - Support for NVIDIA Tesla K10, M2070Q, M2090 GPU cards on System x iDataPlex dx360 M4 - Fixed a problem in System x iDataPlex dx360 M4 where the password expires after creating a new user in the IMM2 web interface - Fixed a problem in System x iDataPlex dx360 M4, when the memory sensor changes from 'critical' to 'warning,' but the severity is not updated in the syslog or the email notification
Version 1.50, 1AOO30W - Supports System HS23, Machine Types: 7875,1929 - Supports System x3650 M4, Machine Types: 7915 - Supports System x3550 M4, Machine Types: 7914 - Supports System x3500 M4, Machine Types: 7383 - Added support for the Intel Xeon E5-2643 processor on the HS23 in BCH-R3, BCS and BCHT chassis - Fixed a problem where the IMM2 incorrectly logged an "Unsupported blade/blower combination" on the HS23 in the BC-E 8677 chassis - Fixed a power restore problem on systems that have 2 Delta power supplies installed - Fixed a problem in System x3650 M4, x3550 M4, x3500 M4, where OpenLDAP Group Authentication filtering function doesn't work - Fixed a problem in System x3650 M4, x3550 M4, x3500 M4, where LDAP account can not login using the AD_CrossDomain tree
Version 1.45, 1AOO28S - Fixed a problem in Flex System x220 where the Chassis Management Module (CMM) Command Line Interface can't display the Mezzanine card information - Fixed a problem in Flex System x220 and x240 where the prebootDSA firmware cannot be updated through Flex System Manager's Update Manager
Version 1.40, 1AOO30T - Supports System x3750 M4, Machine Types: 8722, 8733
Version 1.38, 1AOO30D - Supports System x3630 M4, Machine Type: 7158 - Supports System x3530 M4, Machine Type: 7160
Version 1.36, 1AOO30P - Fixed an intermittent remote media failure in system HS23E - Fixed a problem in system HS23E where remote media does not work when two or more users have concurrent remote control sessions
Version 1.34, 1AOO28Q - Supports Flex System Manager Node, Machine Type: 8731 - Supports Flex System x240 Compute Node, Machine Types: 7863, 8737, 8738 - Supports Flex System x220 Compute Node, Machine Types: 2585, 7906
Version 1.32, 1AOO28N - Supports System x3630 M4, Machine Type: 7158 - Supports System x3530 M4, Machine Type: 7160 - Fixed a problem that may see unexpected fan events after power on in x3100 M4 and x3250 M4 systems - Enhanced robustness on I2C bus test
Version 1.30, 1AOO28M - Supports System HS23E, Machine Types: 8038,8039
Version 1.26, 1AOO26N - Supports System x3650 M4, Machine Types: 7915
Version 1.25, 1AOO26K - Supports System x3550 M4, Machine Types: 7914 - Supports System x3500 M4, Machine Types: 7383 - Supports System x iDataPlex dx360 M4, Machine Types: 7912,7913
Version 1.22, 1AOO26O - Supports System HS23, Machine Types: 7875,1929 Problems Fixed: - Fixed a problem where the BOFM configuration may be lost after a blade power cycle - Fixed an LED error indication that occurs on the BPE4 - Fixed a problem where the Info LED lights during the discovery stage - Fixed a problem where an ABR event is not logged - Fixed an intermittent communication problem between the AMM and IMM2 - Fixed a problem that causes the remote media function to hang when a second user attempts to mount remote media - Fixed a problem where the 'break' keyboard function doesn't work with Serial Over LAN
Version 1.21, 1AOO26L - Supports System HS23, Machine Types: 7875,1929
Version 1.10, 1AOO24B - Supports System dx360 M4, Machine Types: 7918,7919
Version 1.05, 1AOO10K - Fixed the false alert issue in redundant PSU model
Version 1.00, 1AOO10I - Initial Release - Supports System x3250 M4, Machine Types: 2583,2587 - Supports System x3100 M4, Machine Types: 2582,2586
(C) Copyright International Business Machines Corporation 2008 - 2014. All rights reserved.
ibm_fw_imm2_1aoo56e-3_82_anyos_noarch_chg
Dynamic System Analysis (DSA) Preboot Change History
Version 9.50, Build ID DSYTBD1N o New System Support: IBM System X3250 M5 (5458) IBM NeXtScale Node (5455)
o Problem(s) Fixed: 1. PMR - 08641,W01,000 Unisys 9BLTCV - 7143 BOMC CD CheckPointPanel Diag test hangs 2. PMR 08699,W01,000 No LSI raw data from DSAp 9.41
o Enhancement: 1. Embedded DSAp Simplification by removing Low-Value Functionality 2. Fusion IO Raw Data Collection 3. pDSA Simplification for FoD Function & GUI Client 4. Remove Tape Diags function for both online & pDSA (Both Embed and Standalone pDSA) 5. Add warning & report in client for nonsupport systems 6. Change sFTP as the default protocol for transfer log to IBM Service 7. Heartbeat for F2 standalone memory test in manufacturer mode o Limitations: 1. For IR controllers, there's no firmware package build version in the LSI controller page.IR controllers includes: (1). ServeRAID H1110 SATA/SAS Controller for System x (2). ServerRaid-Br10il SAS/SATA controller Expansion Card (3). Racine TLA - N2215 SAS/SATA HBA for IBM System x
2. For Software raid(C100,C105) the Fw version& Fw package version are not supported and will display "N/A" in html and blank in text report.
3. IANet_EEPROM diagnostic test record of Powerville(Onboard NIC card of Yongchun) would be inconsistent among the 4 ports in case the ethernet bus was set to ground due to the limitation of Intel CIM Provider. o Special usage: - 2013 ToolsCenter 13D
Version 9.41, Build ID DSYTC1P o New System Support: Flex System x222 Compute Node (7916) IBM System X3650 M4 HD(5460) o Enhancement: N/A o Limitations: 1. As Intel GPU's name is co-processor, DSA will show the name 'Processor' in PCI page's PCI Device table. Please do not mis-understand this item as CPU device. o Special usage: - 2013 ToolsCenter 13C
Version 9.40, Build ID DSYTB7x o Enhancement: 1. Preboot GUI redesign and enhancement--refine GUI into more customer friendly style. 2. FoD Support--FoD key re-activation. 3. pDSA proxy auto-config retrieve. o Limitations: 1. Immv1 embedded pDSA doesn not support any new drivers due to the limited image size. 2. DSA Does not support "VMware ESXi" page report for ESXi 5.x key due to "vmvisor-offline-query" limitaion . o Special usage: - 2013 ToolsCenter 13B
Version 9.30, Build ID DSYTB27 o New System Support: Flex System x440 Compute Node (7917, 2584) IBM System x3300 M4 (7382) o Problem(s) Fixed: 1. PMR - 05766,YL2,760 Aenservice appeared after running UpdateXpress & DSA. 2. PMR - 05193,W01,000 7147 - Intermittent random PSOD in vmware. multiple
o Enhancement: None o Limitations: - FIFO test of NIC diagnostics is not supported on the Intel I350 Quad Port GbE. Powerville has shared FIFO and shared FIFO registers making a test impossible if four ports are running at once. - For more limitations please refer to readme. o Special usage: - 2012 ToolsCenter 12D
Version 9.29, Build ID DSYTAB6 o New System Support: Flex System x440 Compute Node (7917, 2584) o Problem(s) Fixed: None o Enhancement: None o Limitations: - DSA implemented signature in product build. Please update IMM to 1AOO34V or later before updating pDSA, or flash failure will occur; - The user can not flash Embedded Preboot on VMware ESX3.5 prior to U4. - When flashing DSA Preboot using wflash/lflash, if you notice a build mismatch error, please make sure IMM firmware level is minimum 29B. Once you upgrade the IMM firmware to 29B or higher, DSA Preboot will continue to flash without error; - For more limitations please refer to readme. o Special usage: - NGP-4Q(12B+ FixPack3)
Version 9.28, Build ID DSYTAA4 o New System Support: x3630 M4 (7519) x3550 M4 (7383) o Problem(s) Fixed: None o Enhancement: None o Limitations: - DSA implemented signature in product build. Please update IMM to 1AOO34V or later before updating pDSA, or flash failure will occur; - The user can not flash Embedded Preboot on VMware ESX3.5 prior to U4. - When flashing DSA Preboot using wflash/lflash, if you notice a build mismatch error, please make sure IMM firmware level is minimum 29B. Once you upgrade the IMM firmware to 29B or higher, DSA Preboot will continue to flash without error; - For more limitations please refer to readme. o Special usage: - IMMV2 system 2012 4Q-LFC
Version 9.27, Build ID DSYTA7F o New System Support: None o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme o Special usage: - IMMv1 system 2012 4Q-LFC
Version 9.26, Build ID DSYTA6G o New System Support: None o Problem(s) Fixed: None o Enhancement: DSA Performance Optimization o Limitations: Refer to readme o Special usage: - 2012 ToolsCenter 12C
Version 9.21, Build ID DSYTA1U o New System Support: None o Problem(s) Fixed: 1.Recovered LSI Rawdata: "MegaCli -FwTermLog -Dsply -aALL" o Enhancement: None o Limitations: Refer to readme o Special usage: - 2012 ToolsCenter 12B Plus
Version 9.20, Build ID DSYTA0R o New System Support: x3530 M4 (7160) x3630 M4 (7158) x3750 M4 (8722, 8733) HS23E (8038, 8039) Flex System x220 Compute Node (7906, 2585) o Problem(s) Fixed: 1. PMR 05819,YL2,760 An error occured during the execution of DSA on Windows, DSA exits with an error at the eventlog plugin. o Enhancement: 1. Add HW remote presence key collection for High volume systems. o Limitations: Refer to readme o Special usage: - 2012 ToolsCenter 12B
Version 9.07, Build ID DSYT9CA o New System Support: x3750 M4 (8722, 8733) o Problem(s) Fixed: None o Enhancement: None o Limitations: None o Special usage: None
Version 9.06, Build ID DSYT9BC o New System Support: Flex System x220 Compute Node (7906) o Problem(s) Fixed: None o Enhancement: None o Limitations: None o Special usage: None
Version 9.05, Build ID DSYT9AA o New System Support: x3630 M4 (7158) x3530 M4 (7160) x3100 M4 Refresh1 (2582) x3250 M4 Refresh1 (2583) o Problem(s) Fixed: None o Enhancement: None o Limitations: None o Special usage: None
Version 9.04, Build ID DSYT99E o New System Support: Flex System x240 Compute Node (8737, 8738, 7863) o Problem(s) Fixed: None o Enhancement: None o Limitations: None o Special usage: None
Version 9.03, Build ID DSYT98I o New System Support: HS23E (8038, 8039) o Problem(s) Fixed: None o Enhancement: None o Limitations: None o Special usage: None
Version 9.02, Build ID DSYT97C o New System Support: iDataPlex dx360 M4 server/2U chassis (7912/7913) o Problem(s) Fixed: None o Enhancement: None o Limitations: None o Special usage: None
Version 9.01, Build ID DSYT96D o New System Support: x3500 M4 (7383) x3550 M4 (7914) x3650 M4 (7915) o Problem(s) Fixed: o Enhancement: None o Limitations: None o Special usage: None
Version 9.00, Build ID DSYT95W o New System Support: BladeCenter HS23 (7875) BladeCenter HX5 (7873, 1910) Flex System x240 Compute Node (8737, 8738, 7863) Flex System Manager Node (8735) x3500 M4 (7383) x3550 M4 (7914) x3630 M4 (7158) x3650 M4 (7915) x3690 X5 (7192, 7147) x3850 X5 / x3950 X5 (7143, 7191) o Problem(s) Fixed: 1. PMR 24817,8QG,000, PMR 30680,499,000 After kicking off DSA on one of the management nodes (x3650 M2) of SONAS 1.2(RHEL5 based), the node became unresponsive and dropped out of the cluster.
2. PMR 53575,000,834, PMR 05961,YL4,760 After running DSA, when using linux dump command on a DDS5 usb internal tape drive attached in x3650M2 backup speed becomes very slowly or failed.
3. PMR 26905,095,866 Running DSA 4.0 as well as DSA 3.4 on x3850 X5 the server is freezing, users have to reboot the server.
4. DSA 4.00 and previous version segmentation fault issue
6. PMR 15086,OTH,760 DSA 9.00 with --no-imm-lan option does not work correctly on RHEL5.3. The USB port state is changed during the execution of DSA.
o Enhancement: 1. Add GUI and CLI menu for Features on Demand (FoD) Activation Key Management o Limitations: Refer to readme. o Special usage: None
Version 4.02, Build ID DSYT92I o New System Support: iDataPlex Direct Water Cooled dx360 M4 server o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: None
Version 4.01, Build ID DSYT92H o New System Support: None o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: - 2011 4Q lifecycle
Version 4.00, Build ID DSYT91S o New System Support: None o New server options support: None o Problem(s) Fixed: 1. PMR 15065,OTR,760 On Unisys ES7000 or x3850 X5, the Memory Card number with failed DIMM can not be reported in IPMI Eventlog if the Memory Card is bigger than 4.
o Enhancement: 1. Added > 1TB memory test support o Limitations: Refer to readme. o Special usage: - 2011 ToolsCenter 11D
Version 3.48, Build ID DSYT89PUS o New System Support: None o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: - 2011 3Q lifecycle
Version 3.47, Build ID DSYT89LUS o New System Support: x3100 M4 (2582) x3250 M4 (2583) o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: None
Version 3.46, Build ID DSYT89GUS o New System Support: System x iDataPlex dx360 M3 (6391) o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: None
Version 3.45, Build ID DSYT89EUS o New System Support: None o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: - x3850 X5 / x3950 X5 (7143, 7191) EXA scaling
Version 3.43, Build ID DSYT87HUS o New System Support: BladeCenter HX5 (7873,1910) o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: None
Version 3.43, Build ID DSYT87FUS o New System Support: x3850 X5 / x3950 X5 (7143, 7191) x3690 X5 (7192, 7147) o Problem(s) Fixed: o Enhancement: None o Limitations: Refer to readme. o Special usage: None
Version 3.40, Build ID DSYT85T o New System Support: BladeCenter HS22 (1911) x3650 M3 (5454) o Problem(s) Fixed: None o Enhancement: None o Limitations: Refer to readme. o Special usage: None
Version 3.30, Build ID DSYT80S o New System Support: None o Problem(s) Fixed: None o Enhancement: 1. Correct a problem with LSI MegaRAID reporting for IBM Service o Limitations: Refer to readme. o Special usage: None
Version 3.20, Build ID DSYT75X o New System Support: x3630 M3 (7377) x3690 X5 (7148, 7149) o Problem(s) Fixed: None o Enhancement: 1. Add LSI Hard Disk Drive (HDD) diagnostic back for both the onboard SAS chip and ServeRAID o Limitations: - If you have ServeRAID (M1015) SAS/SATA Controller, 46M0831 installed, you will need one of the following: - uEFI GYE133A or greater for x3200 M3 and x3250 M3 - uEFI Y4E145B or greater for x3400 M2, x3400 M3, x3500 M2 and x3500 M3 - uEFI D6E145C or greater for x3550 M2, x3550 M3, x3650 M2 and x3650 M3 - For more limitations please refer to readme o Special usage: None
Verion 3.20, Build ID DSYT75U o New System Support: x3755 M3 (7164) o Problem(s) Fixed: None o Enhancement: None o Limitations: None o Special usage: None
Verion 3.10, Build ID DSYT70X o New System Support: x3400 M3(7378, 7379) x3500 M3(7380) x3550 M3 (7944, 4254) x3620 M3 (7376) x3650 M3 (7945, 4255) x3690 X5 (7148, 7149) x3850 X5 Standard Single-node and Multi-node models(7145, 7146) x3950 X5 Specially configured Database Engine models (7145, 7146) iDataplex dx360 M3 (6391) HS22V (7871,1949) HX5 (7872, 1909) o Problem(s) Fixed: None o Enhancement: 1. Added ServeRAID data collection o Limitations: - The following function has been temporarily removed from DSA Preboot for both the onboard SAS chip and ServeRAID: - LSI Hard Disk Drive (HDD) diagnostic - If you have ServeRAID (M1015) SAS/SATA Controller, 46M0831 installed, you will need one of the following: - uEFI GYE133A or greater for x3200 M3 and x3250 M3 - uEFI Y4E145B or greater for x3400 M2, x3400 M3, x3500 M2 and x3500 M3 - uEFI D6E145C or greater for x3550 M2, x3550 M3, x3650 M2 and x3650 M3 - For more limitations please refer to readme o Special usage: None
Version 3.02.56, Build ID DSYT56e o New System Support: None o Problem(s) Fixed: None o Enhancement: - The following systems are supported when BoMC downloads the corresponding system enablement pack: HS22V (7871,1949) x3550 M3 (7944,4254) x3650 M3 (7945,4255) x3400 M3 (7378,7379) x3500 M3 (7839) dx360 M3 (6391) o Limitations: - No HDD diagnostics available - To ensure quality and stability of the DSA code, we have reverted some display functionality of RAID information to what was shown in previous versions of DSA. This affects RAID display on the following adapters: Megaraid 8480 Serveraid MR10i Serveraid MR10is Serveraid MR10m Serveraid MR10k Serveraid M1015 Serveraid M5014 Serveraid M5015 On these adapters, the RAID information is generated from the output of separate command line tools and the format may not match other output in DSA. - For more limitations please refer to readme o Special usage: None
Version 3.00, Build ID: DSYT55a o New System Support: None o Problem(s) Fixed: None o Enhancement: - Added support for Machine Types 7327, 7328, 4251, 4252, 4261 o Limitations: - No HDD diagnostics available - For more limitations please refer to readme o Special usage: None
Version 1.16, Y4YT19AUS o New System Support: None o Problem(s) Fixed: None o Enhancement: - Added support for Machine Types 7839, 7836, 7837 o Limitations: None o Special usage: None
Version 1.15, TMYT20AUS o New System Support: None o Problem(s) Fixed: None o Enhancement: - Added support for Machine Types 7321, 6380, 7323 o Limitations: None o Special usage: None
Version 1.14, D6YT37AUS o New System Support: None o Problem(s) Fixed: None o Enhancement: - Added support for Machine Types 7946, 4198, 7947, 4199 o Limitations: None o Special usage: None
Version 1.13, P9YT48AUS o New System Support: None o Problem(s) Fixed: None o Enhancement: - Added support for Machine Types 7870, 1936, 7809 o Limitations: None o Special usage: None
Version 1.00 - Initial release
(C) Copyright International Business Machines Corporation 2008 - 2012. All rights reserved. ibm_fw_dsa_dsytd2y-9_50_anyos_anycpu_chg
QLogic 16 Gb Fibre Channel Adapter MultiFlash Update for System x QLogic Corporation. All rights reserved.
Version 3.20.03 Date: 10/01/2013 BIOS 3.0 version 3.24 uEFI version 6.10 FC Firmware - v7.01.00
* Added additional time to login target when called * after EFI driver unloads. (ER110755.ER110855) * Added code to display message when 64 bit address detected. * Added support for Execution Throttle for P3P (ER106372) * Check for invalid LUN in CTRL-Q scan devices. * Fixed bug in CTRL_Q utility that could cause some cosmetic display issues. * Configure ISP24xx if on slot 0. * Added "QLogic" to PnP productid (ER104424) * Fixed bug with CTRL-Q Loopback Utility (ER100729). * Added code to check/program Feature Config checksum. * Fix bug that could cause buffer overrun in CTRL-Q with Report Lun command (ER100294). * Added check for PCI address change when updating option card data structure. * Changed code to use 32 bit pointer to allocate/deallocate EBDA memory. * Added code to check/program Feature Config checksum. * Fixed cosmetic issue in displaying data rate in CTRL-Q * Fixed display issue with CTRL-Q Diskutility(ER98727) * Fixed Lun select issue with CTRL-Q (ER98675). * Fixed bug in displaying selectable boot lun (ER98226) * Removed 4G data rate option for OEM adapter (ER98228) * Limit leading '0's in CTRL-Q menu (ER98389). * Set 'Aggressive Cooling' flag for OCSD. * Enabled Personality Change option. * Fixed issue with not restoring defaults on port 1 (ER 97619) * Fixed issue with serdes data saved incorrectly. (ER 97654) * Added code to limit Report Lun List size to 256 luns * Added check for 0 lun count when selecting device (ER 97385) * Disable Personality Change option in CTRL-Q. * Fixed bug with WWNN handling for MCTP.(ER 96920) * Added check for Set MD2 set to 0 (restore defaults) (ER96912) * Added code to reset Port Config after Internal loopback test(FCoE). * Added support for 16 bit lun (er96090). * Add support for Set MD2 CLP string. * Added code to issue Load Flash FW (3) MB command as part ISP start sequence. (ER 94035). * Fixed code to prevent async event from causing BIOS to hang when scanning for devices (er94371). * Fix code to disable ALT+1 Hotkey (er92844) . * Fixed CTRL-Q code mailbox timeout (er92957). * Added warning message in Personality change screen. * Updated BIOS to version 3.12 of non-hilda BIOS * Removed check for Virtual Address on Cold Boot. * Changed code to check for signature aaaaaaaah before updating virtual mac address. * Changed code to ignore soft boot signature aaaaaaaah * Added code to save device number in OCSD. * Added code to read cold boot register signature to determine when BIOS should update/restore virtual Mac address. * Fixed bug where retry count was not always being updated. * Added code to support ECHO lopback command. * Added support NCSI Flex Address.
Version 3.20.00 Date: 8/30/2013 BIOS 3.0 version 3.22 uEFI version 5.27 FC Firmware - v7.00.01
- Added code to display message when 64 bit address detected. - Added support for Execution Throttle for P3P (ER106372) - Added code to not display connection options for Hilda Trinity adapter. - Check for invalid LUN in CTRL-Q scan devices. - Fixed bug in CTRL_Q utility that could cause some cosmetic display issues. - Add Hilda CLP _hss support. - Configure ISP24xx if on slot 0. - Added "QLogic" to PnP productid (ER104424) - Check for 4G flag in NVRAM for Hilda FC.(ER104714) - Fixed bug with CTRL-Q Loopback Utility (ER100729). - Added code to check/program Feature Config checksum. - Fix bug that could cause buffer overrun in CTRL-Q with Report Lun command (ER100294).
Version 2.01.55 Date: 1/16/2013 BIOS 3.0 version 3.16 uEFI version 5.27 FC Firmware - v6.03.00
-Fix an issue where the first 4 bytes of the BootTargetWWN are set to FF
Version: 2.01.26 Date: Initial Release BIOS 3.0 version 3.16 uEFI version 5.26 FC Firmware - v6.03.00
IBM Flex System IB6132 2-port FDR InfiniBand Adapter PN: 90Y3454 PSID: IBM0FD0140019 Firmware: 2.30.2010 uEFI: 11.02.38
IBM Flex System EN4132 2-port 10Gb Ethernet Adapter PN: 90Y3466 PSID: IBM0FE0140023 Firmware: 2.30.3100 uEFI: 11.02.38
IBM Flex System EN6132 2-port 40Gb Ethernet Adapter PN: 90Y3482 PSID: IBM1060110017 Firmware: 2.30.2010 uEFI: 11.02.38
IBM Flex System IB6132D 2-port FDR InfiniBand Adapter PN: 90Y3486 PSID: IBM1070110019 and IBM1070111019 Firmware: 2.30.2010 uEFI: 11.02.38 mlnx_fw_nic_2_0-3_0_0_5_sles11_x86-64_chg
uEFI Flash Update Version 1.00 (BuildID A8E104U) Change History
Version 1.00 - BuildID: A8E104U ------------------------------------------------- Problem(s) Fixed: - Fixed issue in which single-socket systems could hang during UEFI boot. - Fixed issue in which system would not boot to generic hard drive boot order entry. - Fixed issue in which editing boot order using ASU would cause valid boot entries to disappear. Enhancements: Limitations: Dependencies: ibm_fw_uefi_a8e104u-1_00_anyos_32-64_chg
=============================================== Change History =============================================== Document Name: Change History Document Status: IBM General Avalibility Document Version: 3.2.3 Latest Driver Version: 3.2.3.0 Document Updated: 05/30/2013 Product: Brocade FC/NIC/CNA
=================================================
Please visit www.brocade.com/hba for full documentation, additional drivers, and management applications.
Version 3.2.3.0 New Features and Feature Enhancement: - Support for patching firmware via boot image - Support for Linux PTP - Support for UEFI Health Check Protocol - Support for SLES11SP3
Version 3.2.1.0 New Features and Feature Enhancement: - Support for "IBM Flex System FC5024D 4-port 16Gb FC Adapter" PART_NUMBER "95Y2381" - Support for RHEL5.9 and RHEL6.4
Fixes and Enhancements: - Enhanced Linux driver data path to properly handle IPv6 packets. - Enhanced Linux driver to make sure user configured path tov value is persistent and is not changed due to change in dev_loss_tmo.
Version 3.2.0.0 Release for FC/NIC/CNA
New Features and Feature Enhancement: - Updated code for Brocade 1867 IBM Flex System FC5022 FC Adapter for x22 - BB Credit Recovery - Forward Error Correction (FEC) - Diagnostic Port (D-Port) - LUN Level IO Latency/Stats - UCM (Unified Configuration Manager) - Windows Network Performance and scalability enhancement
Fixes or enhancements: - For Brocade 8x5/4x5, I/O interrupt latency values are dynamically updated. Changes are effective for all the ports on the given adapter. - Addressed infrequent PSOD in VMware ESX with iSCSI or VLAN configured traffic in DCB enabled network. - Enhanced BR1860 Tape IO performance. - Improved BR1860 initialization on Xen kernel.
Version 3.1.0.1 Release for 16G FC/NIC/CNA
Adapter Features - Updated code for Brocade 1867 IBM 16G Mezzanine Fabric Adapter.
HBA - Fibre Channel 16G Support
Fixes and Enhancements: N/A
Version 3.0.3.1 Initial release for 16G FC/NIC/CNA
Adapter Features - Initial support for Brocade 1867 IBM 16G Mezzanine Fabric Adapter.
HBA - Fibre Channel 16G Support
Fixes and Enhancements: N/A brcd_fw_cna_3_2_3_0_linux_32-64_chg
ServeRAID M5100 Series SAS/SATA Controller Firmware Update for Linux
Adapters Supported: ServeRAID M5110 SAS/SATA Controller for IBM System x (81Y4481) ServeRAID M5110e SAS/SATA Controller for IBM System x ServeRAID M5120 SAS/SATA Controller for IBM System x (81Y4478)
NOTE TO SERVICE - Reference RETAIN #N/A
Version 23.16.0-0027 - Critical ------------------- Fix(es): - Addressed data exposure issue when using CacheCade - Fixed issue where Supercap shows 0 Capacitance - Fixed iBBU09 battery issue that caused a VD cache policy to remain in write-through mode after a manual relearn - Fixed iBBU09 battery issue that caused a VD cache policy to periodically toggle between write-back/write-through mode - The limits for iBBU09 battery charging were not updating properly in a learn cycle - Ensures a single supercap pack is not supported on 2GB memory module. - Resolves a firmware crash seen while doing continuous sas cable pulls. - Ensures OpROM loads even if segment address is 0xC0000. - Fixed an issue where the adapter is running iMR machine checking after requesting host memory. - Fixed an issue where HII does not allow the user to make use of the remaining free capacity to configure additional VD for R50/R10. - Fixed an issue where an HII: empty warning prompt is given when creating a CacheCade VD with forced writeback option. - Fixed and issue where Windows cannot install without a VGA device on board. - Fixed and issue in EFI WebBIOS were consistency check is still shown in progress after 1 PD is removed from a R1 array.
Version 23.16.0-0018 - Suggested ------------------- Fix(es): - Fixed an issue where the adapter is running iMR machine checking after requesting host memory. - Fixed an issue where HII does not allow the user to make use of the remaining free capacity to configure additional VD for R50/R10. - Fixed an issue where an HII: empty warning prompt is given when creating a CacheCade VD with forced writeback option. - Fixed and issue where Windows cannot install without a VGA device on board. - Fixed and issue in EFI WebBIOS were consistency check is still shown in progress after 1 PD is removed from a R1 array.
Version 23.12.0-0016 - Suggested ------------------- Fix(es): - Added isync to prevent speculative execution while memory is being allocated. - Delayed enablement of POM until AFTER valid memory range is provided by host system.
Version 23.12.0-0011 - Suggested ------------------- Enhancement(s): - Implemented Limited Band Charging for iBBU09 (RETAIN tip H21631) - Changed BIOS check to determine if running in HAMR, in order to ensure nothing gets broken when user has an iButton which is not programmed. - Changed controller status for safe mode to show controller status as safe mode and disable debug message logging in serial port.
Fix(es): - Fixed an issue where HII hangs when trying to enter configuration management while in safe mode. Changed the safe mode warning message as below: "Controller is running in safe mode. Safe mode is used for diagnostic purposes only. Limited operations such as Configuration Preview, Clear Configuration and View/Change Controller Properties are allowed in this mode. Other operations such as Create Configuration, Import and Clear Foreign Configurations are not allowed. To exit safe mode, correct the fault, and reboot your computer." - Fixed an issue where having more than three adapters results in a calculation error for the offset to store physical disk info for fourth adapter, due to BIOS not clearing upper byte of AX (that is AH which is containing some non zero value). - Fixed an issue where the Wrong spanned drive group size is displayed by WebBIOS (Ctrl-H).
Version 23.7.1-0010 - Suggested ------------------- Fixes: - Fix an issue related to the where the TSOC (EEPROM) is not able to read or write from the firmware which will result in the message "Incompatible secondary iButton present." - Fix a HII broswer issue where Cachecade virtual drive can be selected as a boot device. - Fix a HII broswer issue where the user is unable to clear the controller configuration when there are no drives attached. - Fix an issue where the BIOS doesn't display the RAID level and VD size correctly at BIOS POST.
Version 23.7.1-0009 - Suggested ------------------- Fixes: - Fixed an issue where SoH is bad after a learn cycle but iBBUI shows good status. - Fixed an issue where hi-temp warning was not being displayed.
Version 23.7.0-0037 - Suggested ------------------- Fixes: - Corrected differential signals for Phys 2 and 3 that caused slot numbers in simple swap configurations to be incorrect. - Fixed an issue when 'maintain PD failed history' is enabled, and a cable is removed while a drive is added, the drives state goes to optimal instead of foreign unconfigured bad. - Fixed a problem where a capacity change is reported after a rebuild completes on a Cache Cade volume. - Fixed a controller firmware hang when the recovery of a medium error takes to long. - Fixed an issue where the SATA BBM (Bad Block Manager) list was being corrupted. - Fixed an issue where FoD (Feature on Demand) Options were being lost because of errors while accessing the TSOC. - Fixed a problem where the controller firmware would crash and drives would go offline when a bad block entry was created during a check consistency operation. - Fixed a problem where drives were being marked unconfigured bad (foreign) on reboot. - Fixed problem where a member of a CacheCade volume did not get marked as foreign when the drive was pulled with 'maintain PD failed history' enabled. - Fixed a problem where during a rebuild, a former hot spare that was now in a state of unconfigured good, moved back to the state hot spare, which then automatically started a copyback operation, causing the rebuild to restart. - Fixed a problem where a controller fault occurred during a reboot while a physical device was in progress of a PD Erase.
Version 23.7.0-0029 - Suggested ------------------- Enhancements: - Added support for Cache Cade 2.1 - Added Support for PI Drives
Fixes: - Fixed an issue where the firmware reports device initialization completion status to be greater than 100% at startup. - Fix an issue where when a secure foreign drive was present, VD creation fails because firmware becomes unresponsive - Added a check for the presence of PD before writing the data arms of a protected LD during BGI. - Fixed Firmware asserts in CacheMemAllocForPrebootApps() when memory was allocated twice by BIOS. - Fixed an issue with USB Cacheoffload restore fails after multiple power cycles onServeRAID M51xx controllers. - Fixed an issue where querying SMART / PFA Status returns "all zeros" in Sense Data. - Fixed an issue where the import of a config from MR to iMR resulted in a firmware crash. - Fixed an issue where iMR firmware crashed while creating 8/16/32 KB stripe size Lds. - Fixed background initialization watermark conversion to PD LBA. - Fixed write protected R1E data arms during initialization. - Fixed an issue where MR firmware crashed while discarding pinned cache. - Fixed an issue where a dirty LD dependency information of SSD pd has stale entries. - Corrected an issue during system booting from pinned cache, firmware goes to loop message BootMsgDcmd - Fixed an issue where a BGI was aborted and restarted, elapsed time was not reset. - Fixed an issue where the start ref for a shared cache line was not an indicator of the offset into the stripe. - Fixed an issue where the firmware hangs while running CC on a rebuilt R1 VD with SBBM. - Fixed an issue where the firmware was wrongly adding puncture entries. - Fixed an issue where rebuild was ran twice on a target drive with 100% full SBBM table. - Fixed an issue where the firmware was generating powersave change event when DS3 was not enabled, due to this application are not parsing the event. - Fixed an issue where recon from R0 to R1 using 3 TB drive causes firmware to report excessive unexpected sense events. - Fixed an issue, in which the bbuMode would revert to the factory default value of 5, when automatic learn cycle was enabled. - Fixed an issue where cache offload firmware reports unnecessary High Temp Event due to incorrect temp value. - Fixed an issue in which a Patrol Read may not start under certain conditions. - Fixed an issue where the firmware hits montask after discarding the cache when a snapshot VD was involved. - Fixed an issue where the firmware hangs during pin cache destage as dirty lines in that map never become zero. - Fixed an issue where CC fails to correct media error at 2TB location on 2 3TB SATA drives that support WU. - Fixed an issue where a new XML file was added to the nvdata, the buffer to hold the uncompressed nvdata overflowed. - Fixed an issue where an imported drive becomes unconfigured good when secure VD erase was running. - Fixed an issue where CC stops progressing on a R6 VD with media errors. - Fixed an issue where 3TB Hitachi HDD failed in immunity test (Electrostatic Noise test). - Fixed an issue where controller features are lost if RAID Key was not detected. - Fixed an issue where performance degraded in RAID 5 Sequential Writes due to command Out-of Ordering. - Fixed an issue where "Native configuration is no longer supported" message in post. - Fixed an issue where (DDR3) Initialization fails with fault 0x91a1 - initial DFIRL selected too low. - Fixed an issue where subsequent drives are dropped when all drives in the stagger spin up drives fails on boot sequence.
Version 23.2.1-0043 - Suggested ------------------- Fixes: - Fixed an issue where "Potential non-optimal configuration due to drive PD commissioned as emergency spare" alarm would trigger erroneously. - Fixed an issue where Copyback does not progress upon inserting drives. - Fixed an issue When allowMixInLD is Disabled, and causes Copyback Fails after Rebuild to Emergency Hot Spare. - Fixed an issue where the Firmware faults while flashing. - Fixed an issure where querying SMART / PFA Status to Return all zeros in Sense Data. - Fixed an issue where the Re-inserted Drives becomes Unconfigured_good causing auto rebuilds to fail to start.
Version 23.2.1-0033 ------------------- - Initial release ibm_fw_sraidmr_5100-23_16_0-0027_linux_32-64_chg
package version 2.3.1c ====================== Changes have been applied to only NX2 devices. Please refer to table above for each firmware code change. First firmware update tool is for 578xx series.(88Y5921, 94Y5230, 94Y5232, 94Y5181, 44T1361)
package version 2.2.1b ====================== -Changes were made to 44W4475,44W4479 devices to pick new level of UEFI v7.6.52. This UEFI code change for 5709/5709s devices is the only change betweeen 2.2.1b and 2.2.1a.
package version 2.2.1a ====================== -Changes were made to the 42C1781, 90Y9370, 90Y9352, 39Y6066, 49Y4220, 49Y7910, 49Y7900. (See above list for the firmware levels in your Broadcom Device.)
package version 2.1.9a ============================================================================================ -Changes made to the 5718, 5719 and 5720 firmware levels. (90Y9352, 90Y9370, 49Y7900. See above list for current firmware levels.) -No change for NX2 products in this package.
package version 2.1.8e ====================== Problems Fixed: - Changes were made to the UEFI code to fix 49Y7910(BCM57712/Cobia) issues.
package version 2.1.8d (See brcm_fw_nic_2.1.8d-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 46M6164, 46M6168, 49Y7910 and 81Y3133. - Changes were mande to the PXE code for the 39Y6066, 42C1780, 42C1781, 42C1790, 42C1791, 44W4466, 44W4475, 44W4479, 44X1940, 46M6164, 46M6168, 49Y4220, 49Y7910 and 81Y3133. - Changes were made to the UEFI code for the 42C1780, 42C1781, 42C1790, 42C1791, 44W4466, 44W4475, 44W4479, 44X1940, 46M6164, 46M6168, 49Y4220, 49Y7910 and 81Y3133. - Changes were made to the iSCSI code for the 42C1780, 42C1781, 49Y4220 and 49Y7910.
package version 2.1.7e (See brcm_fw_nic_2.1.7e-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the UEFI code for the 42C1780, 42C1781, 44W4475 , 44W4479 , 44X1940
and 49Y4220. - Added support for the 49Y7910.
package version 2.1.7d (See brcm_fw_nic_2.1.7d-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the UEFI code for the 42C1780, 42C1781, 42C1790, 42C1791, 44W4465 , 44W4466 , 44W4475 , 44W4479 , 44X1940 , 46M6164 , 46M6168, 49Y4220 and 81Y3133. - Fixed a problem where the MAC addresses for the HS22/HS22V LOM were incorrectly set to zero.
package version 2.1.7c (See brcm_fw_nic_2.1.7c-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 46M6164 and 46M6168. - Changes were made to the NCSI code for the 46M6164 and 46M6168. - Changes were made to the PXE code for the 42C1790, 42C1791, 46M6164, 46M6168, 44W4465 and 44W4466. - Changes were made to the UEFI code for the 42C1790, 42C1791, 46M6164, 46M6168, 44W4465 and 44W4466. - Changes were made to the iSCSI code for the 42C1780, 42C1781 and 49Y4220.
package version 2.1.7b (See brcm_fw_nic_2.1.7b-chg_anyos_anycpu.zip for details.) Problems Fixed: - Fixed problem running the PPC firmware update tool on some PPC systems.
package version 2.1.7a (See brcm_fw_nic_2.1.7a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1909, 1936, 1949, 3808, 3809, 3815, 3817, 3821, 3822, 4195, 4198, 4199, 4254, 4255, 7141, 7144, 7145, 7146, 7148, 7149, 7164, 7233, 7234, 7378, 7379, 7380, 7809, 7836, 7837, 7839, 7870, 7871, 7901, 7902, 7944, 7945, 7946, 7947, 42C1780, 42C1781, 42C1790, 42C1791, 44W4475, 44W4479, 44X1940, 46M6164, 46M6168 and 49Y4220 - Changes were made to the NCSI code for the 1909, 1936, 1949, 3808, 3809, 3815, 3817, 3821, 3822, 4195, 4198, 4199, 4254, 4255, 7145, 7146, 7148, 7149, 7164, 7378, 7379, 7380, 7809, 7836, 7837, 7839, 7870, 7871, 7872, 7944, 7945, 7946, 7947, 44W4475, 44W4479, 46M6164 and 46M6168. - Changes were made to the iSCSI code for the 42C1780, 42C1781 and 49Y4220. - Changes were made to the UEFI code for the 46M6164, 46M6168, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 42C1780, 42C1781, 42C1790, 42C1791 and 49Y4220. - Changes were made to the PXE code for the 39Y6066, 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 46M6164, 46M6168 and 49Y4220.
package version 2.1.6b (See brcm_fw_nic_2.1.6b-chg_anyos_anycpu.zip for details.) Problems Fixed: - The update tool was modified to fix a problem updating the firmware when certain option cards are installed in the system.
package version 2.1.6a (See brcm_fw_nic_2.1.6a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1909, 1936, 1949, 3808, 3809, 3815, 3817, 3821, 3822, 4195, 4198, 4199, 4254, 4255, 7141, 7144, 7145, 7146, 7148, 7149, 7164, 7233, 7234, 7378, 7379, 7380, 7809, 7836, 7837, 7839, 7870, 7871, 7901, 7902, 7944, 7945, 7946, 7947, 42C1780, 42C1781, 44W4475, 44W4479, 44X1940, 46M6164, 46M6168 and 49Y4220 - Changes were made to the NCSI code for the 46M6164, 46M6168, 44W4465, 44W4466, 42C1790, and 42C1791. - Changes were made to the iSCSI code for the 42C1780, 42C1781 and 49Y4220. - Changes were made to the UEFI code for the 46M6164, 46M6168, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 42C1780, 42C1781, 42C1790, 42C1791 and 49Y4220. - Changes were made to the PXE code for the 39Y6066, 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 46M6164, 46M6168 and 49Y4220.
package version 2.1.5b (See brcm_fw_nic_2.1.5b-chg_anyos_anycpu.zip for details.) Problems Fixed: - Added iSCSI config update support for mfg.
package version 2.1.5a (See brcm_fw_nic_2.1.5a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the NCSI code for the 1909, 1936, 1949, 3808, 3809, 3815, 3817, 3821, 3822, 4195, 4198, 4199, 4254, 4255, 7145, 7146, 7148, 7149, 7164, 7378, 7379, 7380, 7809, 7836, 7837, 7839, 7870, 7871, 7872, 7944, 7945, 7946, 7947, 44W4475, 44W4479, 42C1790 and 42C1791 - Changes were made to the UEFI code for the 46M6164, 46M6168, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 42C1780, 42C1781, 42C1790, 42C1791 and 49Y4220. - Changes were made to the IPMI code for the 7141, 7144, 7233, 7234, 7901 and 7902.
package version 2.1.4a (See brcm_fw_nic_2.1.4a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the PXE code for the 39Y6066, 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 46M6164 and 46M6168. - Changes were made to the UEFI code for the 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 46M6164 and 46M6168.
package version 2.1.3c (See brcm_fw_nic_2.1.3c-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the iSCSI code for the 42C1780 and 42C1781. - Changes were made to the UEFI code for the 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 46M6164 and 46M6168. - Changes were made to the boot code for the 46M6164 and 46M6168.
Enhancements: - Added version check to prevent firmware updates of code that is not newer than already installed code. - Added "-force" command line option to allow forcing the firmware update.
package version 2.1.3b (See brcm_fw_nic_2.1.3b-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1936, 1949, 3808, 3809, 3815, 3817, 3821, 3822, 4198, 4199, 4254, 4255, 7141, 7144, 7145, 7146, 7233, 7234, 7378, 7379, 7380, 7836, 7837, 7839, 7870, 7871, 7901, 7902, 7944, 7945, 7946, 7947, 42C1780, 42C1781, 44W4475, 44W4479 and 44X1940. - Changes were made to the NCSI code for the 1936, 1949, 3808, 3809, 3815, 3817, 3821, 3822, 4198, 4199, 4254, 4255, 7145, 7146, 7378, 7379, 7380, 7836, 7837, 7839, 7870, 7871, 7944, 7945, 7946, 7947, 44W4475 and 44W4479. - Changes were made to the PXE code for the 39Y6066, 42C1780, 42C1781, 44W4475, 44W4479 and 44X1940. - Changes were made to the UEFI code for the 42C1780, 42C1781, 44W4475, 44W4479 and 44X1940. - Changes were made to the iSCSI code for the 42C1780 and 42C1781.
package version 2.1.3a (See brcm_fw_nic_2.1.3a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the PXE code for the 26K4842, 39R8624, 39Y9306, 39Y9310, 42C1600, 42C1632, 46M6164, 46M6168, 44W4465, 44W4466, 73P9030, 22P7801, 31P6301, 31P6401, 39Y6079, 39Y6088, 39Y6093, 39Y6098, 42C1790, 42C1791, 73P3501, 73P4001, 73P4101 and 73P4201. - Changes were made to the UEFI code for the 46M6164, 46M6168, 44W4465, 44W4466, 42C1790, and 42C1791. - Changes were made to the NCSI code for the 46M6164, 46M6168, 44W4465, 44W4466, 42C1790, and 42C1791. - Changes were made to the boot code for the 46M6164, 46M6168, 44W4465, 44W4466, 42C1790, and 42C1791.
package version 2.1.1c (See brcm_fw_nic_2.1.1c-chg_anyos_anycpu.zip for details.) Problems Fixed: - none.
Enhancements: - Added support for the 1949, 4254, 4255, 7378, 7379, 7380, 7871, 7944 and 7945.
package version 2.1.1b (See brcm_fw_nic_2.1.1b-chg_anyos_anycpu.zip for details.) Problems Fixed: - Fixed problem where the firmware update failed to run correctly on RHEL5u4-XEN.
package version 2.1.1a (See brcm_fw_nic_2.1.1a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1885, 1913, 1914, 1915, 1936, 3808, 3809, 3815, 3817, 3821, 3822, 4198, 4199, 7141, 7144, 7163, 7233, 7234, 7809, 7836, 7837, 7839, 7870, 7901, 7902, 7946, 7947, 7978, 7979, 7995, 7996, 7997, 8853, 8877, 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 39Y6066, 42C1780, 42C1781, 42C1790 and 42C1791. - Changes were made to the NCSI code for the 1936, 3808, 3809, 3815, 3817, 3821, 3822, 4198, 4199, 7809, 7836, 7837, 7839, 7870, 7946, 7947, 44W4465, 44W4466, 44W4475, 44W4479, 42C1790 and 42C1791. - Changes were made to the PXE code for the 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 39Y6066, 42C1780, 42C1781, 42C1790 and 42C1791. - Changes were made to the UEFI code for the 44W4465, 44W4466, 44W4475, 44W4479, 44X1940, 42C1780, 42C1781, 42C1790 and 42C1791. - Changes were made to the iSCSI code for the 42C1780 and 42C1781.
Enhancements: - Added support for the 46M6164 and 46M6168.
package version 2.1.0a (See brcm_fw_nic_2.1.0a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1936, 3808, 3809, 3815, 3817, 3821, 3822, 4198, 4199, 7141, 7144, 7233, 7234, 7836, 7837, 7839, 7870, 7901, 7902, 7946, 7947, 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466, 44W4475, 44W4479 and 44X1940. - Changes were made to the PXE code for the 39Y6066, 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466, 44W4475, 44W4479 and 44X1940. - Changes were made to the ISCSI code for the 42C1780 and 42C1781.
package version 2.0.9h (See brcm_fw_nic_2.0.9h-chg_anyos_anycpu.zip for details.) Problems Fixed: - Removed the minimum boot code level check for the 44W4465 and 44W4466.
Enhancements: - Added support for the 3808, 3809, 3815, 3817, 3821, 3822, 4198, 4199, 7836, 7837, 7839 and 9233.
package version 2.0.9g (See brcm_fw_nic_2.0.9g-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the UEFI code for 42C1780, 42C1781, 42C1790, 42C1791, 44W4465 44W4466, 44W4475, 44W4479 and 44X1940. - Fixed the problem where the PXE code for the 44W4465 and 44W4466 failed to update under 64bit Linux.
Enhancements: - Added support for the 7946 and 7947.
package version 2.0.9f (See brcm_fw_nic_2.0.9f-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1885, 1913, 1914, 1915, 7141, 7144, 7233, 7234,
7940, 7941, 7971, 7972, 7978, 7979, 7985, 7995, 7996, 7997, 8853, 8877, 39Y6066, 42C1780, 42C1781, 42C1790, 42C1791, 44W4465, 44W4466 and 44W4479. - Changes were made to the NCSI code for the 42C1790, 42C1791, 44W4465, 44W4466 and 44W4479. - Changes were made to the PXE code for 42C1790, 42C1791, 44W4465, 44W4466 and 44W4479.
Enhancements: - Added support for the 1936, 7870 and 44W4475. - Added UEFI code for 42C1790, 42C1791, 44W4465, 44W4466, 44W4479 and 44X1940.
package version 2.0.9e (See brcm_fw_nic_2.0.9e-chg_anyos_anycpu.zip for details.) Problems Fixed: - Added a bnx2 device driver version check for version 1.6.6b or greater.
package version 2.0.9c (See brcm_fw_nic_2.0.9c-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1885, 1915, 7901, 7902, 7971, 7972, 7995, 8853 and 44W4479. - Changes were made to the PXE code for the 39Y6066, 42C1780, 42C1781 and 44W4479. - Changes were made to the iSCSI code for the 42C1780 and 42C1781 - Changes were made to the NCSI code for the 44W4479.
Enhancements: - Added support for the 44X1940.
package version 2.0.8f (See brcm_fw_nic_2.0.8f-chg_anyos_anycpu.zip for details.) Problems Fixed: - Fcode support was removed for the PXE code for the 44W4465 and 44W4466. This change does not result in a change in the PXE code version number. - Changes were made to the PXE code for the 39Y6066, 42C1780 and 42C1781 to fix a problem where some systems hang when loading PXE code.
package version 2.0.8e (See brcm_fw_nic_2.0.8e-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the PXE code for the 39Y6066, 42C1780, 42C1781 and 44W4479. - Changes were made to the IPMI code for the 7141, 7144, 7233 and 7234. - Changes were made to the UMP code for the 7901 and 7902.
Enhancements: - Added support for the 6388, 7942, 44W4465 and 44W4466.
package version 2.0.8d (See brcm_fw_nic_2.0.8d-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 7141, 7144, 7233 and 7234.
Enhancements: - Added support for the 42C1780 and 42C1781.
package version 2.0.8c (See brcm_fw_nic_2.0.8c-chg_anyos_anycpu.zip for details.) Problems Fixed: - None.
Enhancements: - Added support for the 7901 and 7902
package version 2.0.8b (See brcm_fw_nic_2.0.8b-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the PXE code for the 39Y6066.
Enhancements: - Added support for the 44W4479.
package version 2.0.8a (See brcm_fw_nic_2.0.8a-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1885, 1913, 1914, 1915, 7141, 7144, 7971, 7972, 7978, 7979, 7985, 7995, 7996, 7997, 8853, 8877, 9228, 9229, 9230 and 39Y6066. - Changes were made to the ASF code for the 6218, 6223, 6225, 6227, 6228, 8488, 8648, 9228, 9229, 9230. - Changes were made to the UMP code for the 39Y6066. - Changes were made to the PXE code for the 22P7801, 26K4842, 31P6301, 31P6401, 39R8624, 39Y6066, 39Y6079, 39Y6088, 39Y6093, 39Y6098, 39Y9306, 39Y9310, 42C1600, 42C1632, 73P3501, 73P4001, 73P4101, 73P4201, 73P9030. - Changes were made to the IPMI code for the 1916, 8014 and 8028.
Enhancements: - Added support for the 7233, 7234, 7940 and 7941.
package version 2.0.7 (See brcm_fw_nic_2.0.7-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the PXE code for the 22P7801, 26K4842, 31P6301, 31P6401, 39R8624, 39Y6066, 39Y6079, 39Y6088, 39Y6093, 39Y6098, 39Y9306, 39Y9310, 42C1600, 42C1632, 73P3501, 73P4001, 73P4101, 73P4201, 73P9030.
Enhancements: - Added support for the 1916, 8014 and 8028.
package version 2.0.6 (See brcm_fw_nic_2.0.6-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1913, 1914, 7141, 7143, 7144, 7978, 7979, 7996, 7997, 8877 and 39Y6066. - Changes were made to the UMP code for the 39Y6066. - Changes were made to the PXE code for the 39Y6066.
package version 2.0.5 (See brcm_fw_nic_2.0.5-chg_anyos_anycpu.zip for details.) Problems Fixed: - None
Enhancements: - Added support for the 4190, 4191, 4192, 4193, 4194, 4367 and 4368.
package version 2.0.4 (See brcm_fw_nic_2.0.4-chg_anyos_anycpu.zip for details.) Problems Fixed: - None
Enhancements: - Added support for the 7141, 7143 and 7144.
package version 2.0.3 (See brcm_fw_nic_2.0.3-lin-win-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1885, 1913, 1914, 1915, 7971, 7972, 7978, 7979, 7985, 7995, 8853, 8877, 39Y6066. - Changes were made to the IPMI code for the 1879, 1880, 1883, 1884, 1887, 4362, 4363, 4364, 4365, 4366, 7362, 7364, 7365, 7367, 7973, 7974, 7975, 7976, 7977, 7981, 7984, 7986, 8485, 8490, 8491, 8832, 8835, 8837, 8840, 8841, 8843, 8848, 8849, 8850, 8863, 8864, 8865, 8866, 8872, 8874, 8878, 8879. - Changes were made to the ASF code for the 6218, 6223, 6225, 6227, 6228, 8488, 8648, 9228, 9229, 9230. - Changes were made to the PXE code for the 22P7801, 26K4842, 31P6301, 31P6401, 39R8624, 39Y6066, 39Y6079, 39Y6088, 39Y6093, 39Y6098, 39Y9306, 39Y9310, 42C1600, 42C1632, 73P3501, 73P4001, 73P4101, 73P4201, 73P9030.
package version 2.0.0b (See brcm_fw_nic_2.0.0b-nx-nx2-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changed the firmware update process to NOT reset the ethernet devices during the firmware update process.
package version 2.0.0 (See brcm_fw_nic_2.0.0-nx-nx2-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the UMP (Universal Management Port) code for the 1885, 7971, 7972, 7995 and 8853.
package version 1.1.1 (See brcm_fw_nic_1.1.1-nx-nx2-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 1879, 1880, 1887, 4347, 4348, 4362, 4363, 4364, 4365, 4366, 6218, 6223, 6225, 6227, 6228, 7969, 7973, 7974, 7975, 7976, 7977, 7992, 8485, 8486, 8488, 8490, 8491, 8648, 8837, 8840, 8841, 8849, 39Y6098, 39Y9306, 42C1600, 42C1632 and 73P3501. - Changes were made to the IPMI code for the 1879, 1880, 1887, 4362, 4363, 4364, 4365, 4366, 7969, 7973, 7974, 7975, 7976, 7977, 7992, 8485, 8490, 8491, 8837, 8840, 8841 and 8849. - Changes were made to the PXE code for the 22P7801, 26K4842, 31P6301, 31P6401, 39R8624, 39Y6079, 39Y6088, 39Y6093, 39Y6098, 39Y9306, 39Y9310, 42C1600, 42C1632, 73P3501, 73P4001, 73P4101, 73P4201 and 73P9030.
package version 1.1.0 (See brcm_fw_nic_1.1.0-nx-nx2-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the Boot Code for the 1913, 1914, 4347, 6218, 6223, 6225, 6227, 6228, 7969, 7971, 7972, 7978, 7979, 7985, 7995, 8486, 8648, 8853, 8877, 9228 and 9229. - Changes were made to the ASF code for 6218, 6223, 6225, 6227, 6228, 8648, 9228 and 9229. - Changes were made to the PXE code for the 39Y6066. - Changes were made to the
Enhancements: - Added support for the 1879, 1880, 1883, 1884, 1887, 1913, 22P7801, 31P6301, 31P6401, 39Y9306, 39Y6066, 39Y6079, 39Y6088, 39Y6093, 39Y6098, 39Y9310, 4348, 4366, 7362, 7364, 7365, 73P3501, 73P4001, 73P4101, 73P4201, 7992, 7995, 8488 and 9230.
package version 1.0.0 (See brcm_fw_nic_1.0.0-nx-nx2-chg_anyos_anycpu.zip for details.) Problems Fixed: - Changes were made to the boot code for the 8832, 1914, 7971, 7972, 7978, 7979 7985, 8853 and 8877. - Changes were made to the UMP (Universal Management Port) code for the 7971, 7972 and 8853. brcm_fw_nic_2_3_1d_linux_32-64_chg