TS4300 Tape Library Fix List =================================================================================================== Firmware Level: 1.6.2.0-A00 Release Date: 09/11/23 =================================================================================================== New Features: - Open SSL 3.0 implementation Fixes: - Added ability to specify the key size in the Certificate Signing Request wizard =================================================================================================== Firmware Level: 1.6.1.0-B00 Release Date: 07/31/23 =================================================================================================== New Features: - LTO9 Media Optimization Wizard Fixes: - Fixed problem when KMIP is used in combination with SKLM server - Added multiple security fixes - Improved robotics operations - Fixed issue where KMIP chrashes per a large number of key requests - Fixed issue where OCP users are shown in Local Users Page =================================================================================================== Firmware Level: 1.6.0.0-A00 Release Date: 12/14/22 =================================================================================================== New Features: - None Fixes: - Updated JQuery to newer version 3.x due to performance improvements and security fixes - Added support to send email notifications to more than one address - Fixed issue where a command is incorrectly aborted when having multiple control paths - Multiple help pages updates - Fixed issue where the Certificate Wizard - Subject Alternative Name did not support IP Addresses =================================================================================================== Firmware Level: 1.5.0.2-C00 Release Date: 11/30/22 =================================================================================================== New Features: - None Fixes: - Fixed issue where BGA expansion controller card gets not upgraded to latest firmware =================================================================================================== Firmware Level: 1.5.0.2-A00 Release Date: 08/01/22 =================================================================================================== New Features: - None Fixes: - Support for BGA version of expansion controller =================================================================================================== Firmware Level: 1.5.0.1-B00 Release Date: 03/22/22 =================================================================================================== New Features: - None Fixes: - Fixed issue where the library could stay offline/idle since it did not account for sequential mode when checking for LUN master drives - Fixed issue where SNTP fails to slew if time difference is too large - Added temperature offset to LTO9 FH fan control - Updated lighttpd due to some segfault issues that could cause the Web GUI to hang =================================================================================================== Firmware Level: 1.5.0.0-A00 Release Date: 12/03/21 =================================================================================================== New Features: - LTO9 tape drive support Fixes: - Fixed issue where LDAP settings were not reset when resetting library to default configuration - Multiple Help pages updates - Fixed issue where events time was inconsistent with library time - Fixed issue where SNMPv1 does not handle multiple community names - Fixed issue where web sessionID was not regenerated - Fixed issue missing events reported to rsyslog server in case TCP RST has been occurred =================================================================================================== Firmware Level: 1.4.1.0-B00 Release Date: 05/31/21 =================================================================================================== New Features: - None Fixes: - Documentation improvements for library and drive diagnostics - Fixed issue where non admin users were not allowed to change their password - Fixed issue where TA28d was not reported for redundant power supply failure - Fixed issue where TA flags where not triggered for SCSI - Fixed issue where an event was not reported for an elevator blocked =================================================================================================== Firmware Level: 1.4.0.0-A00 Release Date: 09/07/20 =================================================================================================== New Features: - None Fixes: - Added a survey to provide feedback to IBM - Added Drive Test option in dropdown menu in Drives page - Improved event handling for the condition where the Robotic Lock Lever is not fully locked or unlocked - Fixed issue where default superuser comes back after firmware upgrade - Fixed issue where incorrect default users were restored from an old backup file - Fixed LDAP issue where when a wide DN is set, several files are shown as if they were regular users - Fixed issue where a firmware downgrade over REST fails - Fixed issue where SNMP app fails with "UNINTENDED TERMINATION" error - Fixed LDAP issue where if adding a Server with an autocomplete password could lead to invalid command parameter - Fixed LDAP issue where users were not added when the group is in a sub folder =================================================================================================== Firmware Level: 1.3.0.1-A00 Release Date: 12/06/19 =================================================================================================== New Features: - None Fixes: - Fixed issue where IO slots were shown on OP panel in source and destination after being removed - Updated error message when not compliant password was used for first login password change - Added control card SN to library logs - Fixed initial configuration wizard issue when default admin was removed - Fixed issue where wrong severity was assigned for move cartridges problems - Fixed issue where an incorrect behavior for move media was shown when there was no tape in library =================================================================================================== Firmware Level: 1.3.0.0-D00 Release Date: 08/16/19 =================================================================================================== New Features: - None Fixes: - Improved login security - Added ability to move cartridges from the operator panel - Added SNIA MIB file - Fixed issue where KMIP Connectivity Check can take longer that RMI autologout - Fixed issue where an invalid configuration did not report the proper error - Fixed issue where custom certificate backup failed with "internal software error" message - Fixed issue where SKLM z/OS does not work with IPv6 link local address - Fixed issue where RMI and OCP report different drive encryption status - Improvements for sequential mode operation - Fixes for CVE-2018-20679 and CVE-2019-5489 vulnerabilities - Fixed issue where the state of drive is shown as Idle during drive initialization - Fixed issue where event 4154 is logged when certificate is invalid - Fixed issue where SSL Create Custom Certificate Wizard fails to generate CSR if hostname is too long - Fixed issue where IPv6 DNS does not work for SMTP server =================================================================================================== Firmware Level: 1.2.1.0-A00 Release Date: 12/10/18 =================================================================================================== New Features: - 40 Slots Accessor support Fixes: - Improvements for auto calibration - Upgrade of Unzip from 5.52 to 6.00 - Upgrade of Lighttpd to apply security fixes - Fixed issue where Robotic cycle counter is reset to 0 in Robotic NVM - Fixed issue where no event is logged about robotic movement problem after failed autocalibration - Fixed issue where no event is generated when trying to update drive FW when library is busy - Fixed issue where no ticket is created for failed pre-inventory initialization - Fixed issue where data is written unencrypted after switching from KMIP -> SKLM -> KMIP - REST - Fixed issue where it's not possible to unlock mailslot with user/monitor account - Fixed issue where no Warning Event 4018 was generated after a wrong Drive FW upgrade - Fixed issue where power shutdown starts after 10 seconds although up/down buttons are still pressed on the OCP - Fixed issue for SKLM z/OS with IPv6 link local address - Fixed issue where tape VOLSER not showing up in sKLM logs when using KMIP - Improvements of GUI Email (SMTP) Settings buttons =================================================================================================== Firmware Level: 1.2.0.0-B00 Release Date: 10/01/18 =================================================================================================== New Features: - SKLM for z/OS Encryption Fixes: - Improvement of 3D View tooltip - Improvement of validation message when adding users - Improvement of the layout of Modify Port Settings dialog - Improvement of recovery process when incorrect inventory - Fixed issue where Expert/Basic Partition Wizard can be started with loaded drive - Fixed issue where a Move a Tape by Web Interface into a non partition does not show a warning - Fixed issue where library switches to Idle instead of Idle (Offline) during magazine wait period - Fixed issue where queuing of more than 2 mailslot unlocks does not work - Fixed spelling mistake in solution suggestion of Event 4158 - Fixed typo in troubleshooting steps for Event 4155 - Fixed issue where led is off after attempt to unlock mailslot when system is busy - Fixed issue where library state changed to Offline for a long time after attempt to open partition wizard when mailslot is being unlocked - Fixed REST issue where no error was returned after resetting the drive removed from library - Fixed issue where wrong message is shown during disabling I/O slots - Fixed issue where horizontal scroll bar appears, but it is unusable in OP Panel - Improvement of log package - Fixed problem where basic partition wizard can not be started with IE11 - Fixed issue where a blank popup was shown on modify port settings page - Fixed problem where drive cleaning test could fail - Fixed issue where a confirmation message is not shown after change SNMP settings - Fixed issue where information about KMIP Server and encryption mode was not correct in system log - Fixed issue where wrong message was shown when not valid hostname was used for SNMP Target - Fixed issue where library got stuck in magazine-removed state after magazine removal and re-insertion - Fixed issue where error event listing doesn't load most recent event - Fixed problem where a locked user could login if another user changes the Password Rules to not lock out - Fixed REST issue where Admin can get the list of service events - Fixed REST issue where the text for service events is not correctly shown - Fixed REST issue where Library status "Unit lock unlocked" is shown as "Unknown" - Fixed REST issue where GET /rest/partition/information shows wrong LUN information - Fixed issue KMIP Wizard during first configuration - Fixed issue where move cycle counter in robotic is not correct after system restart - Fixed LDAP Issue with using user names with parentheses - Fixed typo in KMIP Wizard - Fixed problem where Unit Auto Calibration Wizard stopped with timeout - Fixed problem where OP Panel Pin was not set properly after Configuration File restore - Fixed issue where Warning Event 4124 was shown during Demo Mode Test - Fixed issue where library in Sequential Mode shows Idle (Offline) in red instead Idle in green - Fixed problem where error event 2065 was shown during initialization - Fixed Security Vulnerabilities CVE-2018-0732, CVE-2018-5733 and CVE-2018-5391 - Fixed problem where primary ports are disabled after drive FW upgrade by SCSI - Fixed problem with insufficient memory when pulling library logs =================================================================================================== Firmware Level: 1.1.1.2-A00 Release Date: 04/30/18 =================================================================================================== New Features: - Support of sequential mode Fixes: - Improvement of GUI dialogs - Improvement of SSL signing wizard - Improvement of I/O Station and Magazine timeout - Improvement of KMIP wizard - Fixed problem where a corrupted drive FW did not report an error during update - Improvement of Basic Partition wizard - Improvement of Logical Library wizard - Improvement of SNIA-SML-MIB - Fixed problem where IP and host name is not shown correctly in SNMP traps - Fixed problem where some operations can be started while reset to defaults is in progress - Improvement of Help information - Fixed problem where GUI and OP panel could hang after the upload of custom certificate - Fixed problem where clearing values of KMIP wizard does set the correct default values - Improvement of IPv4 Network configuration in OP Panel - Fixed problem where LTO8 drive could fail writing data if LME is enabled - Fixed problem where KMIP setup could fail with I/O error - Fixed problem where drives and slots configuration can be lost after configuring partition with KMIP - Fixed problem where self signed KMIP certificate does not work with SKLM v2.7 - Fixed problem where maximum number of partitions is incorrect in Expert Partition wizard - Fixed problem where invalid characters can be saved for SMTP - Improvements for LTO Type M cartridges management - Fixed problem where Initial configuration wizard could fail in the Date & Time page =================================================================================================== Firmware Level: 1.1.1.1-B00 Release Date: 01/29/17 =================================================================================================== New Features: - Un-initialized M8 media support Fixes: - Fixed problem where user could set illegal values for date and time - Improvement for Drive Tests wording - Fixed issue where a cartridge in drive may not be reported in library inventory - Fixed issue where a warning about an older FW is not shown when downgrading the library FW - Improvement for events 2053 and 2054 troubleshooting - Fixed problem where the Basic Partition Wizard could crash - Fixed issue where naming of a resolved ticket is not correct - Fixed issue where self signed certificate is not selected as default - Fixed issue where Restore configuration button is active when no file was selected - Fixed issue where wellness test status is not updated correctly - Fixed problem where Domain name is not validated correctly - Fixed problem where SMTP did not report a library reboot - Fixed problem where login was not possible in Web Interface after unit to unit lock-unlock and power cycle - Improvement for KMIP error message when using a not supported certificate - Improvement for magazine button led handling - Improvements for IO station management - Improvements for Magazine management - Fixed problem where if no reboot was made for factory reset, the library will stay in reserved state - Fixed issue where incorrect encryption is shown in system log - Fixed problem where drive encryption settings were not updated after logical library encryption update - Fixed issue where an error pop up was not cleared when trying to change the port configuration while drive is powering up - Fixed issue where the accessor could fall in a recovering loop after an accessor block =================================================================================================== Firmware Level: 1.1.1.0-A00 Release Date: 11/23/17 =================================================================================================== New Features: - LTO8 tape drive support - Pre-initialized M8 media is supported with a minimum LTO8 tape drive firmware level of HB82 Fixes: - Fixed problem where user has been logged out from Operator Panel without warning message. - Fixed problem where no data validation was made in Manage Encryption wizard when adding a Signed Certificate - Fixed problem where Move button gets an incorrect color when clicked - Fixed incorrect behavior of Stop Test button toggles to Run button immediately when Library Verify Test is aborted even though test is still processing - Fixed issue with header time not matching Time Zone settings - Fixed typo in Operator Panel drive diagnostics message - Fixed message when no license is installed - Fixed issue where Retry button does not refresh in the Management GUI after reboot from FW Upgrade - Fixed unexpected response from REST Interface on invalid IO open request - Fixed issue where Management GUI activity is short time changing to scanning and back idle - Fixed issues with Auto Clean - Fixed problem where no event is logged after failure during head test - Fixed problem where wrong result is reported for Library test after Drive test failed - Fixed issue when I/O button is pushed during movement into drive - Fixed issue where no event is logged after drive test failed due to diagnostic cartridge placed into wrong I/O slot - Fixed problem where library status is shown as Upgrading after a failed Upgrade - Improvement of error handling when export of diag cartridge failed and new drive test is started - Improvement of Start Test button by blocking it quickly after starting the test - Improvement of Cartridge and Slots pages by inform which slots belong to I/O stations - Fixed issue where an unhandled exception was thrown when having spooling problems - Improvement for capitalization for text on buttons - Fixed field name for LDAP wizard - Fixed issue where status Magazine removed is not reported after powering on the unit with released magazine - Improvement for message shown for incompatible drive error - Fixed problem where library could enter in a loop after a system reboot from Operator Panel - Improvement for event description for Cartridge found in inaccessible slot of lowermost slots - Improvement for incompatible drive event handling - Fixed problems with magazine button behavior in case of emergency stop condition - Fixed occasional inventory scan problem if emergency stop condition occurs during magazine unlock - Improvement for IO Station handling in the case of an Emergency stop during the magazine scan - Fixed Management GUI hang issue during Drive Tests - Fixed magazine button hang condition if pressed while media removal is prevented - Improvement for description of "Drive was hot-removed" event - Fixed issue where Operator Panel Display initialization was delayed up to 5s after power on - Fixed problem where Wellness test failed on verification of power board instead of power supply - Fixed issue where Magazine can be re-opened while locking - Fixed problem where it was possible to configure not supported drives - Fixed problem where the IO Station was not scanned after moving back into the unit - Fixed problem where Autoclean did not work - Improvement for License file management when non-CRU controller is put into non-CRU chassis - Improvement for Management GUI main menu - Fixed problem where Library Properties screen is shown empty - Fixed problem where Magazine buttons were disabled after release timeout - Fixed issue where empty hostname is not on Operator Panel - Fixed issue where "Library Firmware changed" event was logged in Configuration Log after restoring configuration - Fixed issue where Update button behaves incorrectly in Update Drive Firmware page - Improvement for Reset Internal IP Range by adding a confirmation message - Improvement for Ipv6 validation in Operator Panel - Improvement for Ipv4 validation in Management GUI - Fixed issue where an incorrect error pops up for "Cleaning tape expired" event - Fixed problem where Operator Panel fail when downgrading Library Firmware - Fixed issue where unlocked IO Station LED stops flashing when another IO Station is reinserted - Fixed problem where IO Station handling hangs when a request to open magazine is made - Fixed problem where Magazine is not scanned if delay of inventory scan occurs - Improvement for Remote Logging with a confirmation dialog after navigation from Remote Logging page - Fixed issue where an incorrect error is shown after Drive firmware update completes with Internet Explorer - Improvement for login list when many users are available - Fixed an unexpected unit attention when trying to open Magazine while media removal prevented - Improvement of troubleshooting steps for events 2053 and 2054 - Fixed issue with Kerberos when having users with the same name - Fixed problem to load session after switch from SSL to not SSL - Fixed problem where Personality is missing if system is in Startup Halted State - Fixed incorrect title of Kerberos error popup - Fixed issue where some valid symbols are not allowed in principal name for Kerberos - Fixed issue where some valid symbols used in the realm name caused an "internal Software error" for Kerberos - Fixed problem where deletion of user (principal) containing special chars was not impossible for Kerberos - Fixed problem where Encryption key requests were not handled anymore after SCSI abort - Fixed problem where it was not possible to read encrypted data - Fixed problem where Superuser cannot clear KMIP config - Fixed problem where KMIP certificates were removed from unit after disabling KMIP license =================================================================================================== Firmware Level: 1.1.0.1-A00 Release Date: 08/29/17 =================================================================================================== New Features: - None Fixes: - Fixed problem where Auto login caused a database access error