TS2900 Fixlist: Library Code 0106.0000 Release Notes - June 29, 2018 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0106.0000 (IBM_3572_0106-0000.fmg) * Drive firmware: * LTO Gen 8 HH LTO8_JAYF (HH SAS only) * LTO Gen 7 HH LTO7_JAYF (HH SAS only) * LTO Gen 6 HH LTO6_JAX1 (HH SAS only) * LTO Gen 5 HH LTO5_H977 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_G9N1 (HH SAS V2 only) * LTO GEN 4 HH V1 LTO4_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 LTO3_93GQ (HH SAS V1 only) Added Functions: * New HTML Web GUI. Removed Functions: * Removed Java GUI. Fixes: * SSL ciphers updated. * Changed location for settings information. * Changed the auto logout time to 120 minutes. * Fixed issue where configuration data could not be found in library dump. * Fixed issue where when logging into the library from multiple browser tabs they can be closed. * Fixed issue where when maximum users are logged in the prevoius user was logged out instead of oldest. Support: Support for the following ITDT version: * ITDT-SE v9.2.0.20171204 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * General: Operating Systems RHEL6 and higher RHEL7 and higher and Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0080.0000 Release Notes - January 29, 2018 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0080.0000 (IBM_3572_0080-0000.fmg) * Drive firmware: * LTO Gen 8 HH LTO8_HB83 (HH SAS only) * LTO Gen 7 HH LTO7_H9E3 (HH SAS only) * LTO Gen 6 HH LTO6_H991 (HH SAS only) * LTO Gen 5 HH LTO5_H971 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_G9N1 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * Support for M8 Media Removed Functions: * None Fixes: * Fixed issue where encryption failover might not work * Fixed issue where SMTP caused a hang situation on OP panel and GUI disconnect Support: Support for the following ITDT version: * ITDT-SE v9.3.0.20181029 * ITDT-GE v9.3.0.20181029 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * General: Operating Systems RHEL6 and higher RHEL7 and higher and Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0074.0000 Release Notes - November 21, 2017 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0074.0000 (IBM_3572_0074-0000.fmg) * Drive firmware: * LTO Gen 8 HH LTO8_HB83 (HH SAS only) * LTO Gen 7 HH LTO7_H9E3 (HH SAS only) * LTO Gen 6 HH LTO6_H991 (HH SAS only) * LTO Gen 5 HH LTO5_H971 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_G9N1 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * Support for LTO Gen-8 SAS Tape Drives and Media * Support of TLS 1.2 for communication of Web-SSL and EKM-SSL * Supported new 4 ciphers with SHA256 Removed Functions: * Support of TLS 1.0 for communication of Web-SSL and EKM-SSL * All ciphers with SHA1 for SSL communication Fixes: * Fix to store passwords in flash memory in data hashed by SHA256 * Fixed issue about web-GUI not brought up with Java 7 Support: Support for the following ITDT version: * ITDT-SE v9.2.0.20171204 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * Un-initialized M8 media and Pre-initialized M8 media is supported with a minimum LTO8 tape drive firmware level of HB83 and a minimum library firmware level of 0080. The usage of M8 media with prior firmware levels may result in a permanent reduction in the capacity of the M8 media from 9 TB to 6 TB (native). * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * RISK Support: LTO Gen 3 drives based on FVT test * General: Operating Systems RHEL6 and higher RHEL7 and higher and Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0071.0000 Release Notes - Nov 128, 2016 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0071.0000 (IBM_3572_0071-0000.fmg) * Drive firmware: * LTO Gen 7 HH LTO7_G9Q1 (HH SAS only) * LTO Gen 6 HH LTO6_G9P1 (HH SAS only) * LTO Gen 5 HH LTO5_G9N1 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_G9N1 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * None Removed Functions: * Removed 3DES cipher from web connections. Fixes: * Removed 3DES cipher from web connections. * Fixed issue where numbers in the first character of the domain name for SMTP sender addresses were not allowed. Library Code 0070.0000 Release Notes - May 13, 2015 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0070.0000 (IBM_3572_0070-0000.fmg) * Drive firmware: * LTO Gen 7 HH LTO7_G341 (HH SAS only) * LTO Gen 6 HH LTO6_G351 (HH SAS only) * LTO Gen 5 HH LTO5_G361 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_G361 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * Enable the upload of a customer certificate for use with HTTPS on the web user interface * SHA-256 security protocol Removed Functions: * SHA-1 security protocol Fixes: * Fixed about library did not ask to change user pass provide by admin. * Fixed about problem that the web admin log in with limited privileges after new password change. * Admin is not able to login with theirs original privileges. * SNMP walk displays IPv6 address, however from library side IPv6 was not configured or provided in the library. * Changed SHA-1 hash to SHA-256 for Java Applet and SSL used on Web-GUI. * Added the ability for a customer to upload customer's own SSL server certificate. * Fixed about auto cleaning is not working on TS2900 libraries. * Fixed about SKLM FAIL/BACK OVER - Lib reports Chk002D LDI Error during Write. * Fixed about SNMP Query differences between libraries. * Fixed about Library Map Help screen needs LTO7 update. * Fixed about SNMP walk display IPv6 address but not configured on library. * Fixed about Common Weakness Enumeration (CWE). * Fixed about BUF for HTTP issue led to WEB loss. * Fixed about Network Error Pop up does not go away upon clicking OK. * Fixed about Java Applet Behavior Change. * Changed web packet to compatible format for manufacturing tool. * Fixed not to show attribute tags(,) in Library Map Help screen. * Fixed about GUI error message on importing certificate. * Fixed about Help context update for supported certificate and private key formats. * Fixed to increase certificate store buffer. * Fixed to remove the test function for IPv6 Ready Logo. * Fixed about the issue that 1U library state is offline after loading incompatible drive code. * Fixed about the issue that Library state remains in failed after using incompatible tape for Normal RW test. * Fixed about the issue that Web-GUI cannot be opened after Jack0018 firmware code(LTO5 level) or earlier is loaded. * Fixed about the issue that library remains offline after loading invalid restore file. * Fixed about the issue that auto cleaning didn’t work with LTO5 auto cleaning enabled. * Fixed about the issue that auto cleaning didn’t stop with LTO6 tape labeled with a clean label. * Fixed about the issue that auto cleaning didn’t work once auto cleaning enabled with a clean tape in cleaning slots. * Fixed about SSL negotiation process errors. * Fixed about the issue that ClassNotFoundException message is sometimes occurring when loading code from jack058 to jack067. * Fixed additionally SNMP walk display IPv6 address but not configured on lib. * Fixed additionally not to cause ClassNotFoundException of Java. * Fixed about OID’s are not being translated on TS2900. * Fixed about DNS hostname is not returned as EKM server address of SNMP MIB. * Fixed about Encryption and KPD links missing after auto reboot and re-login. * Fixed about Exit message needs update for Auto Reboot action. Support: Support for the following ITDT version: * ITDT-SE v9.0.0.20150729 * ITDT-GE v9.0.0.20150914 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * RISK Support: LTO Gen 3 drives based on FVT test * General: Operating Systems RHEL6 and higher RHEL7 and higher and Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0058.0000 Release Notes - October 12, 2015 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0058.0000 (IBM_3572_0058-0000.fmg) * Drive firmware: * LTO Gen 7 HH LTO7_FA11 (HH SAS only) * LTO Gen 6 HH LTO6_F9A1 (HH SAS only) * LTO Gen 5 HH LTO5_F991 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_F991 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * Support for LTO Gen-7 SAS Tape Drives and Media * A new SNMP Query Configuration capability and MIB * Enhanced Password Security Removed Functions: * None Fixes: * Move medium command to move cleaning cartridge to drive is reported as complete to the host with a delay * DHCP enabled, but library does not pick up an Ipv4 address * 1U uses only cartridge of tier 1 if the slots addresses of cleaning deep cell are reversed with auto clean enabled * The remaining cleaning count and the error information of any cartridge in magazine are reset once I/O station opens * "Minimum number of days before password can be changed", only administrator’s password can be changed during unchangeable days * Supported the updated SNMP Query Configuration v1.2 * Not DNS name but invalid IP address (0.0.0.0) is indicated in NTP server field on Library Map of Web when DNS name is set as NTP server address * Library does not log an error code 0x0010 when library is unable to get IP address from DHCPv4 server * Drive Diagnostics cannot be executed when the library indicates media error * Customer should be able to use 1U without that Feature Active key * GUI Library State incorrect * Web-Hang problem, TCP connection cannot get reused after it receives SYN from client on SYN-RECEIVED and aborts * Supported the updated SNMP Query Configuration v1.4 * The OIDs for libraryconfigGroup does not match the one from MIB * Fixed not to cause the login failure after the user doesn’t operate Web-GUI over 2 minutes on login screen * Fixed to reset only ADMIN password via operator panel * Corrected typo in the message on the end of ADMIN password reset on operator panel * Changed the web dialog message to prompt the password change when login with the password is expired * The user may not use old Java applet after loading new 1U firmware * Failed Date and Time reset to 01/03/2008 after to load code * Added some error retries to the process for getting time by NTP * Pass rule # of pass change before old pass can be used again fail * Web LTO7 Drive Upgrade Failed Retry Took 3 hrs * Web Access via IPv6 Failed then IPv4 Failed * Changed the dialog message indicated when user uses unsuitable version of Java applet Support: Support for the following ITDT version: * ITDT-SE v9.0.0.20150729 * ITDT-GE v9.0.0.20150914 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * RISK Support: LTO Gen 3 drives based on FVT test * General: Operating Systems RHEL6 and higher RHEL7 and higher and Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0039.0000 Release Notes - June 12, 2015 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0039.0000 (IBM_3572_0039-0000.fmg) * Drive firmware: * LTO Gen 6 HH LTO6_E6R3 (HH SAS only) * LTO Gen 5 HH LTO5_E6Q3 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_E6Q3 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * None Removed Functions: * None Fixes: * Fix to address the Logjam Attack on TLS connections using the Diffie-Hellman (DH) key exchange protocol. Support: Support for the following ITDT version: * ITDT-SE v8.0.1 * ITDT-GE v8.0.1 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * HP-UX: Integrity Servers (Itanium) only * HP-UX: The following software packages are required for HP AH303A SAS Host Bus Adapter usage. SerialSCSI-00_B.11.31.0803_HP-UX_B.11.31_IA.depot CommonIO_B.11.31.0803_HP-UX_B.11.31_IA_PA.depot * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * General: Operating Systems SLES10 SP4 and higher, RHEL5.6 and higher, RHEL6 and higher & Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0037.0000 Release Notes - April 17, 2015 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0037.0000 (IBM_3572_0037-0000.fmg) * Drive firmware: * LTO Gen 6 HH LTO6_E6R3 (HH SAS only) * LTO Gen 5 HH LTO5_E6Q3 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_E6Q3 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * None Removed Functions: * RC4 cipher related to CVE-2015-2808 Fixes: * Fix to remove RC4 cipher regarding "Bar Mitzvah" Attack for SSL/TLS Support: Support for the following ITDT version: * ITDT-SE v8.0.1 * ITDT-GE v8.0.1 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * HP-UX: Integrity Servers (Itanium) only * HP-UX: The following software packages are required for HP AH303A SAS Host Bus Adapter usage. SerialSCSI-00_B.11.31.0803_HP-UX_B.11.31_IA.depot CommonIO_B.11.31.0803_HP-UX_B.11.31_IA_PA.depot * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * General: Operating Systems SLES10 SP4 and higher, RHEL5.6 and higher, RHEL6 and higher & Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0036.0000 Release Notes - November 7, 2014 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0036.0000 (IBM_3572_0036-0000.fmg) * Drive firmware: * LTO Gen 6 HH LTO6_E6R3 (HH SAS only) * LTO Gen 5 HH LTO5_E6Q3 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_E6Q3 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * None Removed Functions: * SSLv3 support related to CVE-2014-3566 Fixes: * Fix to remove SSLv3 support Support: Support for the following ITDT version: * ITDT-SE v8.0.1 * ITDT-GE v8.0.1 NOTE: For a complete list of ITDT Limitations and Known Issues, please refer to the ITDT Readme file and the "Device Driver Installation and User Guide" distributed with the software. Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * HP-UX: Integrity Servers (Itanium) only * HP-UX: The following software packages are required for HP AH303A SAS Host Bus Adapter usage. SerialSCSI-00_B.11.31.0803_HP-UX_B.11.31_IA.depot CommonIO_B.11.31.0803_HP-UX_B.11.31_IA_PA.depot * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * General: Operating Systems SLES10 SP4 and higher, RHEL5.6 and higher, RHEL6 and higher & Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0034.0000 Release Notes - September 5, 2014 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0034.0000 (IBM_3572_0034-0000.fmg) * Drive firmware: * LTO Gen 6 HH LTO6_E6R3 (HH SAS only) * LTO Gen 5 HH LTO5_E6Q3 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_E6Q3 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * None Removed Functions: * None Fixes: * Sign algorithm changed by the Java certificate. Support: Support for the following ITDT version: * ITDT-SE 8.0 * ITDT-GE 8.0 Known Issues and Limitations: * AIX & LpS: No System FW support for SAS boot on Power 5 servers. * AIX & LpS: User may experience communication interruption with the tape device if there are link errors in the SAS interface (No cable pull support on SAS adapters) * HP-UX: Integrity Servers (Itanium) only * HP-UX: The following software packages are required for HP AH303A SAS Host Bus Adapter usage. SerialSCSI-00_B.11.31.0803_HP-UX_B.11.31_IA.depot CommonIO_B.11.31.0803_HP-UX_B.11.31_IA_PA.depot * ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. * General: Operating Systems SLES10 SP4 and higher, RHEL5.6 and higher, RHEL6 and higher & Windows 2012 and higher do not support LTO3 HH v1 drives * Windows: IBMTape device driver do not support System Managed Encryption on Win2012 R2 Library Code 0033.0000 Release Notes - June 16th, 2014 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0033.0000 (IBM_3572_0033-0000.fmg) * Drive firmware: * LTO Gen 6 HH LTO6_D8E5 (HH SAS only) * LTO Gen 5 HH LTO5_D8D5 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_D8D5 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) Added Functions: * None Removed Functions: * None Fixes: * Implemented Heartbleed Security Update. The “Heartbleed” security flaw exposes security vulnerabilities in OpenSSL software packages. The OpenSSL software package has been updated to close the security vulnerabilities. Known Issues and Limitations: Library Code 0028.0000 Release Notes - November 08, 2013 --------------------------------------------------- Component Firmware The following component firmware is required for this release: * Library code: 0028.0000 (IBM_3572_0028-0000.fmg) * Drive firmware: * LTO Gen 6 HH LTO6_D8E5 (HH SAS only) * LTO Gen 5 HH LTO5_D8D5 (HH SAS only) * LTO Gen 4 HH_V2 LTO4_D8D5 (HH SAS V2 only) * LTO GEN 4 HH V1 dh120723r_C7QJ (HH SAS V1 only) * LTO GEN 3 HH V1 rh090316w_93GQ (HH SAS V1 only) * Note: Identifing V2 drives through the web interface: 1. Select Monitor System from the navigation pane on the left side of the page. 2. Select Library Map to display the graphical view of the library. 3. Click on the Drive component on the library map. Drive information will be displayed on the right side of the page. 4. Refer to the Product ID to determine which drive is installed in the library. • Product ID: ULT3580-HH4 • Product ID: ULT3580-HH4 V2 5. Ensure you download and install the correct drive firmware. • Firmware for the ULT3580-HH4 drive is not compatible with the ULT3580-HH4 V2 drive. • Firmware for the ULT3580-HH4 V2 drive is not compatible with the ULT3580-HH4 drive. * SNMP Mib Files: IBM_TS2900_MIB_2011_2_Rev.013.mib Note: The MIB file is not installed on the library. It is installed on the Customer's SNMP client server. Added Functions: * None Removed Functions: * None Fixes: * Fix cookie failure on Safari * Ignore the first two digit of library serial number when the code calculate MAC and WWNN Support: Support for the following ITDT version: * ITDT-SE v7.1.0 Build065 Known Issues and Limitations: (1) AIX & LpS: No System FW support for SAS boot on Power 5 servers. (2) AIX & LpS: User may experience communication interruption with the tape device if there are link Errors in the SAS interface (No cable pull support on SAS adapters) (3) HP-UX: Integrity Servers (Itanium) only (4) HP-UX: The following software packages are required for HP AH303A SAS Host Bus Adapter usage. - SerialSCSI-00_B.11.31.0803_HP-UX_B.11.31_IA.depot - CommonIO_B.11.31.0803_HP-UX_B.11.31_IA_PA.depot (5) ITDT: For a complete list of ITDT Limitations and Known Issues, please refer to the Readme file and the "Device Driver Installation and User Guide" distributed with the software. (6) Windows 2012/IBM SAS: Host Bus Adapters for 6GB with part number 46M0907 running on xSeries servers will not be supported until a drive and firmware package are released by System X (7) Operating Systems SLES10 SP4 and higher, RHEL5.6 and higher, RHEL6 and higher & Windows 2012 and higher do not support LTO3 HH v1 drives ===================================================================================================