Power9 System Firmware

Applies to:   9008-22L; 9009-22A; 9009-41A; 9009-42A; 9223-22H; 9223-42H; 9009-41G; 9009-22G; 9009-42G; 9223-22S; 9223-42S and 5105-22E .

This document provides information about the installation of Licensed Machine or Licensed Internal Code, which is sometimes referred to generically as microcode or firmware.

Contents

1.0 Systems Affected

This package provides firmware for Power Systems L922 (9008-22L), Power System S922 (9009-22A), Power System S914 (9009-41A), Power System S924 (9009-42A), Power System H922 (9223-22H) Power System H924 (9223-42H), Power Systems S922 (9009-22G), Power Systems S914 (9009-41G), Power Systems S924 (9009-42G), IBM Power System H922 for SAP HANA  (9223-22S), IBM Power System H924 for SAP HANA  (9223-42S), and IBM ESS (5105-22E) servers only.

The firmware level in this package is:

1.1 Minimum HMC Code Level

This section is intended to describe the "Minimum HMC Code Level" required by the System Firmware to complete the firmware installation process. When installing the System Firmware, the HMC level must be equal to or higher than the "Minimum HMC Code Level" before starting the system firmware update.  If the HMC managing the server targeted for the System Firmware update is running a code level lower than the "Minimum HMC Code Level" the firmware update will not proceed.

The Minimum HMC Code levels for this firmware for HMC x86,  ppc64 or ppc64le are listed below.

x86 -  This term is used to reference the legacy HMC that runs on x86/Intel/AMD hardware for the Virtual HMC that can run on the Intel hypervisors (KVM, XEN, VMWare ESXi).
ppc64 or ppc64le - describes the Linux code that is compiled to run on Power-based servers or LPARS (Logical Partitions)
The Minimum HMC level supports the following HMC models:
x86 - KVM, XEN, VMWare ESXi (6.0/6.5)
ppc64le - 7063-CR1,vHMC on PowerVM (POWER8 and POWER9 systems

For information concerning HMC releases and the latest PTFs,  go to the following URL to access Fix Central:
http://www-933.ibm.com/support/fixcentral/

For specific fix level information on key components of IBM Power Systems running the AIX, IBM i and Linux operating systems, we suggest using the Fix Level Recommendation Tool (FLRT):
http://www14.software.ibm.com/webapp/set2/flrt/home

NOTES:
                -You must be logged in as hscroot in order for the firmware installation to complete correctly.
                - Systems Director Management Console (SDMC) does not support this System Firmware level

1.2 IBM i Minimum Levels

Reference the following URL for IBM i Support: Recommended fixes:

https://www-01.ibm.com/support/docview.wss?uid=nas8N1021194

2.0 Important Information

Concurrent firmware update of certain SR-IOV adapters needs AIX/VIOS fix
If the  adapter firmware level in this service pack  is concurrently applied, AIX and VIOS VFs may become failed. To prevent the VF failure, the VIOS and AIX partitions must have the fix for IJ44288 (or a sibling APAR) applied prior to concurrently updating SR-IOV adapter firmware. AIX/VIOS SPs Spring 2023 will ship this fix.  Until then, interim fixes (ifixes) are available from https://aix.software.ibm.com/aix/efixes/ij44288/ or by calling IBM support if an ifix is required for a different level. A re-IPL of the system instead of concurrently updating the SR-IOV adapter firmware would also work to prevent a VF failure.   The following SR-IOV adapter Feature Codes and CCINs are affected : #EC2R/EC2S with CCIN 58FA; #EC2T/EC2U with CCIN 58FB; and #EC66/EC67 with CCIN 2CF3.


Boot adapter microcode requirement
Update all adapters which are boot adapters, or which may be used as boot adapters in the future, to the latest microcode from IBM Fix Central.  The latest microcode will ensure the adapters support the new Firmware Secure Boot feature of Power Systems. This requirement applies when updating system firmware from a level prior to FW940 to levels FW940 and later.
The latest adapter microcode levels include signed boot driver code. If a boot-capable PCI adapter is not installed with the latest level of adapter microcode, the partition which owns the adapter will boot, but error logs with SRCs BA5400A5 or BA5400A6 will be posted.  Once the adapter(s) are updated, the error logs will no longer be posted.

Downgrading firmware from any given release level to an earlier release level is not recommended
Firmware downgrade warnings:
1) Adapter feature codes (#EC2R/#EC2S/#EC2T/#EC2U and #EC3L/#EC3M and #EC66/EC67) when configured in SR-IOV shared mode in FW930 or later, even if originally configured in shared mode in a pre-FW930 release, may not function properly if the system is downgraded to a pre-FW930 release. The adapter should be configured in dedicated mode first (i.e. take the adapter out of SR-IOV shared mode) before downgrading to a pre-FW930 release.
2) If partitions have been run in POWER9 compatibility mode in FW940, a downgrade to an earlier release (pre-FW940) may cause a problem with the partitions starting.  To prevent this problem, the "server firmware" settings must be reset by rebooting partitions in "Power9_base" before doing the downgrade.

If you feel that it is necessary to downgrade the firmware on your system to an earlier release level, please contact your next level of support.

Upgrade from FW941.00 to FW950 will change the QPRCFEAT QMODEL code for the 9009-22G, 9009-41G, and 9009-42G models.
If updating from FW941.00 to FW950 for IBM i, there is a fix for incorrect QPRCFEAT QMODEL values for the 9009-xxG models.  If 3rd party software licenses were installed based on the old incorrect QPRCFEAT QMODEL value, new licenses will be needed to work with the updated value:  The QPRCFEAT QMODEL IBM System Value was showing the 9009-xxG models as 9009-xxA models.  For example, the 9009-22G reported as "EP11" instead of "EP51".  This mismatch can prevent 3rd party software licenses from working.

2.1 IPv6 Support and Limitations

IPv6 (Internet Protocol version 6) is supported in the System Management Services (SMS) in this level of system firmware. There are several limitations that should be considered.

When configuring a network interface card (NIC) for remote IPL, only the most recently configured protocol (IPv4 or IPv6) is retained. For example, if the network interface card was previously configured with IPv4 information and is now being configured with IPv6 information, the IPv4 configuration information is discarded.

A single network interface card may only be chosen once for the boot device list. In other words, the interface cannot be configured for the IPv6 protocol and for the IPv4 protocol at the same time.

2.2 Concurrent Firmware Updates

Concurrent system firmware update is supported on HMC Managed Systems only.

Ensure that there are no RMC connections issues for any system partitions prior to applying the firmware update.  If there is a RMC connection failure to a partition during the firmware update, the RMC connection will need to be restored and additional recovery actions for that partition will be required to complete partition firmware updates.

2.3 Memory Considerations for Firmware Upgrades

Firmware Release Level upgrades and Service Pack updates may consume additional system memory.
Server firmware requires memory to support the logical partitions on the server. The amount of memory required by the server firmware varies according to several factors.
Factors influencing server firmware memory requirements include the following:
Generally, you can estimate the amount of memory required by server firmware to be approximately 8% of the system installed memory. The actual amount required will generally be less than 8%. However, there are some server models that require an absolute minimum amount of memory for server firmware, regardless of the previously mentioned considerations.

Additional information can be found at:
https://www.ibm.com/support/knowledgecenter/9009-22A/p9hat/p9hat_lparmemory.htm

2.4 SBE Updates

Power 9 servers contain SBEs (Self Boot Engines) and are used to boot the system.  SBE is internal to each of the Power 9 chips and used to "self boot" the chip.  The SBE image is persistent and is only reloaded if there is a system firmware update that contains a SBE change.  If there is a SBE change and system firmware update is concurrent, then the SBE update is delayed to the next IPL of the CEC which will cause an additional 3-5 minutes per processor chip in the system to be added on to the IPL.  If there is a SBE change and the system firmware update is disruptive, then SBE update will cause an additional 3-5 minutes per processor chip in the system to be added on to the IPL.  During the SBE update process, the HMC or op-panel will display service processor code C1C3C213 for each of the SBEs being updated.  This is a normal progress code and system boot should be not be terminated by the user. Additional time estimate can be between 6-10 minutes.

The SBE image is only updated with this service pack if the starting firmware level is less than FW950.10.

2.5 NVDIMM Updates

Power 9 ESS 5010-22E servers contain NVDIMMs that may be updated with a service pack. Updating NVDIMM firmware takes approximately 8 minutes per NVDIMM on ESS I/O servers 5105-22E. If an NVDIMM firmware update is required, then this would be incurred only on the initial system boot when updating system firmware or replacing an NVDIMM. There are 4 NVDIMMs per server, so up to an additional 32 minutes might be needed to complete the system boot in these cases.

The NVDIMM firmware is updated with this service pack only when updating from a firmware level less than FW950.10.

3.0 Firmware Information

Use the following examples as a reference to determine whether your installation will be concurrent or disruptive.

For systems that are not managed by an HMC, the installation of system firmware is always disruptive.

Note: The concurrent levels of system firmware may, on occasion, contain fixes that are known as Deferred and/or Partition-Deferred. Deferred fixes can be installed concurrently, but will not be activated until the next IPL. Partition-Deferred fixes can be installed concurrently, but will not be activated until a partition reactivate is performed. Deferred and/or Partition-Deferred fixes, if any, will be identified in the "Firmware Update Descriptions" table of this document. For these types of fixes (Deferred and/or Partition-Deferred) within a service pack, only the fixes in the service pack which cannot be concurrently activated are deferred.

Note: The file names and service pack levels used in the following examples are for clarification only, and are not necessarily levels that have been, or will be released.

System firmware file naming convention:

01VLxxx_yyy_zzz

NOTE: Values of service pack and last disruptive service pack level (yyy and zzz) are only unique within a release level (xxx). For example, 01VL900_040_040 and 01VL910_040_045 are different service packs.

An installation is disruptive if:

            Example: Currently installed release is 01VL900_040_040, new release is 01VL910_050_050.

            Example: VL910_040_040 is disruptive, no matter what level of VL910 is currently installed on the system.

            Example: Currently installed service pack is VL910_040_040 and new service pack is VL910_050_045.

An installation is concurrent if:

The release level (xxx) is the same, and
The service pack level (yyy) currently installed on the system is the same or higher than the last disruptive service pack level (zzz) of the service pack to be installed.

Example: Currently installed service pack is VL910_040_040, new service pack is VL910_041_040.

3.1 Firmware Information and Description

 
Filename Size Checksum md5sum
01VL950_111_045.rpm 171162987
 31853
173c255002210f70f0aaab687e300dae

Note: The Checksum can be found by running the AIX sum command against the rpm file (only the first 5 digits are listed).
ie: sum 01VL950_111_045.rpm

VL950
For Impact, Severity and other Firmware definitions, Please refer to the below 'Glossary of firmware terms' url:
https://www.ibm.com/support/pages/node/6555136
VL950_111_045 / FW950.60

10/20/22		 Impact: Availbility   Severity:  SPE

System firmware changes that affect all systems
  • A change was made for certain SR-IOV adapters to move up to the latest level of adapter firmware.  No specific adapter problems were addressed at this new level.  This change updates the adapter firmware to XX.32.1010 for the following Feature Codes and CCINs: #EC2R/EC2S with CCIN 58FA; #EC2T/EC2U with CCIN 58FB; and #EC66/EC67 with CCIN 2CF3. If this adapter firmware level is concurrently applied, AIX and VIOS VFs may become failed. To prevent the VF failure, the VIOS and AIX partitions must have the fix for IJ44288 (or a sibling APAR) applied prior to concurrently updating SR-IOV adapter firmware. AIX/VIOS SPs Spring 2023 will ship this fix.  Until then, interim fixes (ifixes) are available from https://aix.software.ibm.com/aix/efixes/ij44288/ or by calling IBM support if an ifix is required for a different level. A re-IPL of the system instead of concurrently updating the SR-IOV adapter firmware would also work to prevent a VF failure.
  • Security problems were fixed for vTPM 1.2 by updating its OpenSSL library to version 0.9.8zh.  Security vulnerabilities CVE-2022-0778, CVE-2018-5407, CVE-2014-0076, and CVE-2009-3245 were addressed.  These problems only impact a partition if vTPM version 1.2 is enabled for the partition.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for an intermittent service processor core dump for MboxDeviceMsg with SRCs B1818601 and B6008601 logged while the system is running.  This is a timing failure related to a double file close on an NVRAM file.  The service processor will automatically recover from this error with no impact on the system.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for an SR-IOV adapter in shared mode failing on an IPL with SRC B2006002 logged.  This is an infrequent error caused by a different SR-IOV adapter than expected being associated with the slot because of the same memory buffer being used by two SR-IOV adapters.  The failed SR-IOV adapter can be powered on again and it should boot correctly.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for an SR-IOV adapter in shared mode failing during run time with SRC B400FF04 or B400F104 logged.  This is an infrequent error and may result in a temporary loss of communication as the affected SR-IOV adapter is reset to recover from the error.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for a system crash with a B700F103 logged after a local core checkstop of a core with a running partition.  This infrequent error also requires a configuration change on the system like changing the processor configuration of the affected partition or running Dynamic Platform Optimizer (DPO).
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for a rare system hang that can happen any time Dynamic Platform Optimizer (DPO), memory guard recovery, or memory mirroring defragmentation occurs for a dedicated processor partition running in Power9 or Power10 processor compatibility mode. This does not affect partitions in Power9_base or older processor compatibility modes. If the partition has the "Processor Sharing" setting set to "Always Allow" or "Allow when partition is active", it may be more likely to encounter this than if the setting is set to "Never allow" or "Allow when partition is inactive".
    This problem can be avoided by using Power9_base processor compatibility mode for dedicated processor partitions. This can also be avoided by changing all dedicated processor partitions to use shared processors.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for a partition with VPMEM failing to activate after a system IPL with SRC B2001230 logged for a "HypervisorDisallowsIPL" condition.  This problem is very rare and is triggered by the partition's hardware page table (HPT) being too big to fit into a contiguous space in memory.  As a workaround, the problem can be averted by reducing the memory needed for the HPT.  For example, if the system memory is mirrored, the HPT size is doubled, so turning off mirroring is one option to save space.  Or the size of the VPMEM LUN could be reduced.  The goal of these options would be to free up enough contiguous blocks of memory to fit the partition's HPT size.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for a rare partition hang that can happen any time Dynamic Platform Optimizer (DPO), memory guard recovery, or memory mirroring defragmentation occurs for a shared processor partition running in any compatibility mode if there is also a dedicated processor partition running in Power9 or Power10 processor compatibility mode.  This does not happen if the dedicated partition is in Power9_base or older processor compatibility modes. Also, if the dedicated partition has the "Processor Sharing" setting set to "Always Allow" or "Allow when partition is active", it may be more likely to cause a shared processor partition to hang than if the setting is set to "Never allow" or "Allow when partition is inactive".
    This problem can be avoided by using Power9_base processor compatibility mode for any dedicated processor partitions. This problem can also be avoided by changing all dedicated processor partitions to use shared processors.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for booting an OS using iSCSI from SMS menus that fails with a BA010013 information log.  This failure is intermittent and infrequent.  If the contents of the BA010013 are inspected, the following messages can be seen embedded within the log:
    " iscsi_read: getISCSIpacket returned ERROR"
    " updateSN: Old iSCSI Reply - target_tag, exp_tag"
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for the SMS menu option "I/O Device Information".  When using a partition's SMS menu option "I/O Device Information" to list devices under a physical or virtual Fibre Channel adapter, the list may be missing or entries in the list may be confusing. If the list does not display, the following message is displayed:
    "No SAN adapters present.  Press any key to continue".
    An example of a confusing entry in a list follows:
    "Pathname: /vdevice/vfc-client@30000004
    WorldWidePortName: 0123456789012345
     1.  500173805d0c0110,0                 Unrecognized device type: c"
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for a memory leak in the service processor (FSP) that can result in an out of memory (OOM) condition in the FSP kernel with an FSP dump and reset of the FSP.  This can occur after the FSP has been active for more than 80 days of uptime.  If the problem occurs, the system automatically recovers with a reset/reload of the FSP.
  • A problem was fixed for too frequent callouts for repair action for recoverable errors for SRCs B7006A72, B7006A74, and B7006A75.   The current threshold limit for the switch correctable errors is 5 occurring in 10 minutes, which is too low for a predictable event that requests a part replacement.  With the fix, the threshold value for calling out a part replacement is increased to match what is done for the PCIe Host Bridge ( PHB) correctable errors.  Every correctable error threshold condition on the switch link triggers the too frequent callouts.
    This problem does not pertain to model ESS 5105-22E.
  • A problem was fixed for a service processor FSP kernel panic dump and reset/reload that can occur if there is a network configuration error when using ASMI to change the network.  The SRCs B1817201 and B1817212 are logged prior to the dump.  This problem only occurs when changing the network configuration to an incorrect setting that causes a network timeout.
System firmware changes that affect certain systems
  • On a system with no HMC and a serially attached terminal, a problem was fixed for an intermittent service processor core dump for NetsVTTYServer with B181D30B logged that can when using the terminal console for the OS.  This error causes the console to be lost but can be recovered by doing a soft reset of the service processor.
    This problem does not pertain to model ESS 5105-22E.E.

4.0 How to Determine The Currently Installed Firmware Level

You can view the server's current firmware level on the Advanced System Management Interface (ASMI) Welcome pane. It appears in the top right corner. Example: VL910_123.

5.0 Downloading the Firmware Package

Follow the instructions on Fix Central. You must read and agree to the license agreement to obtain the firmware packages.

Note: If your HMC is not internet-connected you will need to download the new firmware level to a USB flash memory device or ftp server.

6.0 Installing the Firmware

The method used to install new firmware will depend on the release level of firmware which is currently installed on your server. The release level can be determined by the prefix of the new firmware's filename.

Example: VLxxx_yyy_zzz

Where xxx = release level

HMC Managed Systems:

Instructions for installing firmware updates and upgrades on systems managed by an HMC can be found at:
https://www.ibm.com/support/knowledgecenter/9009-22A/p9eh6/p9eh6_updates_sys.htm


NovaLink Managed Systems:

A NovaLink managed system does not have a HMC attached and is managed either by PowerVM Novalink or PowerVC using PowerVM Novalink.
Instructions for installing firmware updates and upgrades on systems managed by PowerVM NovaLink can be found at:
https://www.ibm.com/support/knowledgecenter/9009-22A/p9eig/p9eig_updating_firmware.htm


HMC and NovaLink Co-Managed Systems (Disruptive firmware updates only):

 A co-managed system is managed by HMC and NovaLink, with one of the interfaces in the co-management master mode.
Instructions for installing firmware updates and upgrades on systems co-managed by an HMC and Novalink is the same as above for a HMC managed systems since the firmware update must be done by the HMC in the co-management master mode.  Before the firmware update is attempted, one must be sure that HMC is set in the master mode using the steps at the following IBM KnowledgeCenter link for NovaLink co-managed systems:
https://www.ibm.com/support/knowledgecenter/9009-22A/p9eig/p9eig_kickoff.htm

Then the firmware updates can proceed with the same steps as for the HMC managed systems except the system must be powered off because only a disruptive update is allowed.   If a concurrent update is attempted, the following error will occur: " HSCF0180E Operation failed for <system name> (<system mtms>).  The operation failed.  E302F861 is the error code:"
https://www.ibm.com/support/knowledgecenter/9009-22A/p9eh6/p9eh6_updates_sys.htm


Systems not Managed by an HMC or NovaLink:

Power Systems:

Instructions for installing firmware on systems that are not managed by an HMC can be found at:
https://www.ibm.com/support/knowledgecenter/9009-22A/p9ha5/fix_serv_firm_kick.htm


Systems running Ubuntu operating system:

If Ubuntu will be used to update the system firmware, please follow these instructions to extract the installable binary and update/upgrade the firmware:

1) Download the .gz (tarball) from Fix Central to your Ubuntu system (ie, to /tmp/fwupdate).

2) Extract the .gz file to /tmp/ on the Ubuntu system:

Example:
    tar -xzf /tmp/fwupdate/01VL910_040_040.tar.gz -C /tmp/fwupdate

3) Use update_flash -v -f <extracted file name> to verify the package.

4) Update your firmware using update_flash:

/usr/sbin/update_flash  -f <extracted file name>

System will reboot during the firmware update. When the system reaches Ubuntu run-time state, you can then commit or reject the firmware update:
Commit: /usr/sbin/update_flash -c
Reject:   /usr/sbin/update_flash -r

IBM i Systems:

For information concerning IBM i Systems, go to the following URL to access Fix Central: 
http://www-933.ibm.com/support/fixcentral/

Choose "Select product", under Product Group specify "System i", under Product specify "IBM i", then Continue and specify the desired firmware PTF accordingly.

7.0 Firmware History

The complete Firmware Fix History (including HIPER descriptions)  for this Release level can be reviewed at the following url:
https://www.ibm.com/support/pages/node/6955591