| 02AP730_138_092
05/09/2014
|
Impact: Availability
Severity: SPE
- No SRC posted after critical power fault causes Boundary power off (LIC)
- Implement slow low-pass filtered current sensor to ensure that the currents used by the Current Balance routine remain in sync (DCCA-IH7 FW)
- Change to shutdown WCU if both pump winding thermistors are over 95C (MDA-WCU FW)
- Call out 'Leak Detected' for WCU if both Leak Sensors indicate WET (MDA-WCU FW)
- Check of System Return Temperature Thermistor limits at power on (MDA-WCU FW)
- Flow meter limit changed to prevent erroneous call outs (MDA-WCU FW)
- Add filtering to WCU 'Primary Side Reversed' Warning to prevent erroneous call out (MDA-WCU FW)
- Correct WCU Pump Speeds in N-1 mode with 10 CECs and 0 DEs (LIC)
- Update macro BPCmnfgvapi -m for latest WCU spec (LIC)
- Fixed problem with SRC 14028075 being posted when the dew point is negative (LIC)
- Fixed problem with DCCA Access errors being seen when in Non-Support mode (DCCA-IH7 FW)
- Added Thermal Load Sharing between WCUs at low power (MDA-WCU FW)
- Change to open the Cross-power static circuit breaker as part of BPC service when the mailbox is broken (LIC)
- Post error log for Octant Redundant Soft Switch Test Failure (DCCA-IH7 FW)
- Fix to retain DC power Mode status in the BPR (BPR-IH7 FW)
- Corrected hysteresis used for recovery from input UV faults (BPR-IH7 FW)
- Changed Test Switching to reread and verify initial voltage reading (DCCA-IH7 FW)
- Filter the levels disabled but intended on SRC (14022C51/0315) to prevent erroneous call out in reference to PU Enclosure OT SRC (14020079/04FC) (LIC)
- Turn BPD static circuit breakers back on after BPA loses power occurs (LIC)
- Fix problem with Fips dumps occurred during concurrent CEC DCCA R&V procedure (LIC)
- Disable PRM Recovery in pass 50 and later DCCAs to prevent level dips caused by erroneous test switching fails (DCCA-IH7 FW)
- Prevent Global Level 59 failure after erroneous Test Switching Failure (DCCA-IH7 FW)
|
| 02AP730_124_092
03/11/2013
|
Impact: Availability
Severity: SPE
- Fixed the erroneously call out of "VRM ## Soft Switch Power Good Fault" DCCA failure (14022C52) during a BCM fault recovery
- Fixed the issue with xCAT rvitals log only reporting power from one DCCA on memory levels
- Implemented PRM recovery for pass 45/47 DCCA's
- Fixed the hardware OV issue on level 58 that was seen by both DCCAs due to a problem with the OV Discriminator circuit which can cause both DCCAs to reset
- Fixed the issue where Get Switching could interrupt Test Switching leaving levels biased
- Fixed the issue where the DCCA TPMD Data Processor Power was incorrect
- Fixed the issue where support mode was entered less than 10s after the DCCA was deactivate
|
| 02AP730_118_092
10/31/2012
|
Impact: Function
Severity: SPE
- Added Output UV with OC protection and Intermediate Bus Faults detection to the BPR
- Enhancements to BCM fault detection and recovery for CEC DCCAs
- Enhancements in the inter-DCCA communications for CECs
- Enhancements to VTM fail in place strategy
- Added check for CEC DCCA incompatibility
- Added Fast Trip Motor Overload Protection, fan and pressure transducer trip avoidance when the pumps turn on and off to the Fill & Drain Tool
- Fixed problems with running downlevel Fill & Drain Tools
- Enhancements to the detection of faulted levels in the CEC DCCAs
- Enhancements to BPD fault detection
- Changed the current balancing procedure to prevent power supplies being left unbalanced
- Remove WCU fixed regulation for humidity reduction when CECs are not powered on
- Enhancements to the line cord, CEC Node CPU & Hub Power/Thermal, WCU and Disk Enclosure Disk Population data reported to xCAT rvitals
- Enhancements to the handling when multiple WCUs detect that the system water is out of spec (too hot)
- Fixed various erroneously reported error codes
Known Issues to be fix in next the Service Pack:
- The CEC octant memory power reported by the xCAT rvitals command is off by approximately a factor of 2. The CEC Input Power is being reported correctly.
|
| 02AP730_092_092
05/25/2012
|
Impact: Serviceability
Severity: SPE
- The number of required Water Cooling Units and Bulk Power Supplies
(BPRs) has been changed. The requirement is based on the
number of installed cages and the input line voltage/type
- Changed the pump speeds in various conditions for the Water Cooling Units
- Fixed problems with running downlevel Fill & Drain Tools
- Fixed some BPR rails not turning on after DC input is lost and recovered
- Changed the current balancing procedure to prevent power supplies being left unbalanced
- Added detection and reporting of lack of water flow to Disk
Enclosure power supplies
- Fixed Disk Enclosure being erroneously powered off while servicing a port card
- Fixed various erroneously reported error codes
|
| 02AP730_086_086
04/09/2012
|
Impact: Function
Severity: SPE
- Added support for DC input power
- Improved error detection, fault prevention, and fault recovery on
node power supplies
- Fix Disk Enclosure power supply fans not reaching max speed when
required
- Add recovery of Disk Enclosure power supplies if they reboot due
to loss of bias voltage
- Various fixes for Fill & Drain tool
- Fix incorrect power information being reported to XCAT (BPR
current and Disk Enclosure power usage)
|
| 02AP730_071_071
01/23/2012
|
Impact: Function
Severity: SPE
- Fixed BPC incorrectly going to 'Rack Standby' mode after service
of the BPA
- Fixed generation of various erroneous bulk power supply (BPR)
error codes
- Fixed BPRs not being enabled after completion of service
- Fixed some BPRs incorrectly remaining on after frame is switched
off
- Implemented common firmware to support various Fill/Drain Tool
hardware levels
- Various Fill/Drain Tool operation fixes
- Enhancements and fixes to Water Conditioning Unit operation, error
detection, and service
- Allow extra Water Conditioning Units to be configured to prevent
over-temperature issues for "over-configured" systems
- Enhancements and fixes to CEC power supply operation, error
detection, and service
- Fixed LEDs incorrectly remaining on after service of Disk
Enclosure drives
- Prevent defective port cards from causing Disk Enclosure power on
reset to "hang"
- Improved fault handling for Disk Enclosure port card faults to
prevent erroneous side effect error codes
- Improved Disk Enclosre fan speed algorithm to prevent overheating
for small configurations
|
| 02AP730_054_054
12/02/2011
|
Impact: Function
Severity: SPE
- Enhancements and fixes to Water Conditioning Unit operation, error
detection, and service
- Enhancements and fixes to Fill/Drain tool operation and service
- Enhancements and fixes to frame's bulk power supply (BPR) operation
and service
- Enhancements and fixes for CEC power supplys to prevent
erroneous power faults and add recovery
- Support to light up the frame roll-up LED when servicing BPA
parts
- Emergency Power Off Warning (EPOW) support for Hot Water / Hot
Room
- Support for unlocking of Disk Enclosure carriers for
service
- Increase the number of CECs allowed to power on when running in low
voltage DC range from 4 up to 8
- Many other fixes to service/erroneously generated faults
- Various other general stability/usability fixes
|
| 02AP730_042_042
08/26/2011
|
Impact: New
Severity: NEW
- General Availability Level
|