Power6 Mid-Range Firmware

Applies to: 9117-MMA , 9406-MMA, and 8234-EMA

This document provides information about the installation of Licensed Machine or Licensed Internal Code, which is sometimes referred to generically as microcode or firmware.

Contents

1.0 Systems Affected

This package provides firmware for System p 570 (9117-MMA), System i570 (9406-MMA), Power 570 (9117-MMA), and Power 560 (8234-EMA) servers only.

The firmware level in this package is:

1.1 Minimum HMC Code Level

This section is intended to describe the "Minimum HMC Code Level" required by the System Firmware to complete the firmware installation process. When installing the System Firmware, the HMC level must be equal to or higher than the "Minimum HMC Code Level" before starting the system firmware update.  If the HMC managing the server targeted for the System Firmware update is lower than the "Minimum HMC Code Level" the firmware update will not proceed.

The Minimum HMC Code level for this firmware is:  HMC V7 R3.5.0 with PTFs MH01212 and MH01217 (or higher).

Although the Minimum HMC Code level for this firmware is listed above,  HMC level V7 R3.5.0 with PTF MH01238 (Service Pack 3), or higher is suggested for this firmware level.

For specific fix level information on key components of IBM Power Systems running the AIX, IBM i and Linux operating systems, we suggest using the Fix Level Recommendation Tool (FLRT):
http://www14.software.ibm.com/webapp/set2/flrt/home

For information concerning HMC releases and the latest PTFs,  go to the following URL to access Fix Central.
http://www-933.ibm.com/support/fixcentral/

NOTE: You must be logged in as hscroot in order for the firmware installation to complete correctly.

2.0 Cautions and Important Information

2.1 Cautions

Downgrading firmware from any given release level to an earlier release level is not recommended.
If you feel that it is necessary to downgrade the firmware on your system to an earlier release level, please contact your next level of support.

Upgrading from EM320_031 to EM350_xxx

If your current level of firmware is EM320_031 you must install any higher level of EM320 before upgrading your firmware to this level.

Upgrading from EM310_xxx to EM350_yyy

If your current level of firmware is EM310_xxx,  you must install EM320_040 or higher before upgrading your firmware to this level.

2.2 Important Information

IPv6 Support and Limitations

IPv6 (Internet Protocol version 6) is supported in the System Management Services (SMS) in this level of system firmware. There are several limitations that should be considered.

When configuring a network interface card (NIC) for remote IPL, only the most recently configured protocol (IPv4 or IPv6) is retained. For example, if the network interface card was previously configured with IPv4 information and is now being configured with IPv6 information, the IPv4 configuration information is discarded.

A single network interface card may only be chosen once for the boot device list. In other words, the interface cannot be configured for the IPv6 protocol and for the IPv4 protocol at the same time.

HMC-Managed Systems

For model 560 and model 570 systems, this firmware level provides an enhancement to improve the reporting of power supply fan failures.  These failures will be identified via the new System Reference codes (listed below).  Until the HMC support for these new SRC's is available (end of October 2010), the SRC definitions can be reviewed at http://publib.boulder.ibm.com/infocenter/powersys/v3r1m5/index.jsp?topic=/ipha6_p5/x1xxx.htm
New SRC codes
 Power Supply E1 Power Supply E2 Comments
New SRC for "predictive" fan fault 1100151E 1100152E The power supply fan at location Un-E1 / Un-E2 stopped temporarily but recovered.
Replace the power supply as soon as possible before the fan fails permanently.
New SRC for hard fan fault 1100151F 1100152F The power supply fan at location Un-E1 / Un-E2 failed.  Replace the power supply as soon as possible.

Memory Considerations for Firmware Upgrades

The increase in memory used by the firmware is due to the additional functionality in later firmware releases.

3.0 Firmware Information and Description

Use the following examples as a reference to determine whether your installation will be concurrent or disruptive.

For systems that are not managed by an HMC, the installation of system firmware is always disruptive.

Note: The concurrent levels of system firmware may, on occasion, contain fixes that are known as deferred. These deferred fixes can be installed concurrently, but will not be activated until the next IPL. Deferred fixes, if any, will be identified in the "Firmware Update Descriptions" table of this document. For deferred fixes within a service pack, only the fixes in the service pack which cannot be concurrently activated are deferred.

Note: The file names and service pack levels used in the following examples are for clarification only, and are not necessarily levels that have been, or will be released.

System firmware file naming convention:

01EMXXX_YYY_ZZZ

NOTE: Values of service pack and last disruptive service pack level (YYY and ZZZ) are only unique within a release level (XXX).

For example, 01EM310_067_045 and 01EM320_067_053 are different service packs.

An installation is disruptive if:

Example: Currently installed release is EM310, new release is EM320 Example: EM310_120_120 is disruptive, no matter what level of EM310 is currently
installed on the system Example: Currently installed service pack is EM310_120_120 and
new service pack is EM310_152_130

An installation is concurrent if:

Example: Currently installed service pack is EM310_126_120,
new service pack is EM310_143_120.

Firmware Information and Update Description

For information about previous firmware release levels, see  Section 7.0 Firmware History.

 
Filename Size Checksum
01EM350_085_038.rpm 23773324
 40716

Note: The Checksum can be found by running the AIX sum command against the rpm file (only the first 5 digits are listed).
ie: sum 01EM350_085_038.rpm

EM350
For Impact, Severity and other Firmware definitions, Please refer to the below 'Glossary of firmware terms' url:
http://www14.software.ibm.com/webapp/set2/sas/f/power5cm/home.html#termdefs
EM350_085_038

10/26/10

 Impact: Availability           Severity:  HIPER - High Impact/PERvasive, Should be installed as soon as possible.

System firmware changes that affect all systems

  • HIPER for 8234-EMA and 9117-MMA systems:  On 8234-EMA (Power 560 Express) and 9117-MMA (Power 570) systems,  the firmware has been enhanced to improve reporting of power supply fan problems, which reduces the potential of a unplanned system outage.
  • HIPER:  On systems using the HEA (host Ethernet adapter) function, and on which a CEC concurrent maintenance operation that requires a node evacuation is being done, this fix corrects an issue that has the potential to corrupt information stored in the system memory, which may cause undetected data errors.  This issue was discovered during internal IBM testing, and while it has not been reported on any customer systems, IBM strongly recommends that this fix be applied to all model MMA systems that are running AIX partitions.
  • HIPER:  A problem was fixed that caused the HMC to show the server's status as incomplete, and SRC B7000602 to be logged against SFLPHMCCMDTASK in serviceable events.  This problem can also cause the system to crash when it occurs.
  • HIPER:  A problem was fixed that caused repeated reset/reloads of the service processor, and fail-overs, to occur after a hypervisor-initiated reset/reload of the service processor was completed.  That led to loss of communication between the service processor and the hypervisor (indicated by SRC B182951C).
  • On 9117-MMA (Power 570) systems with 3 or 4 processor drawers, this service pack also fixes a problem that prevented the power supply fan speed in these drawers from adjusting to changes in the ambient temperature.
  • The firmware was enhanced to log SRC B181D30B as informational instead of predictive.
  • The firmware was enhanced to list the attached devices when viewing the adapter information for a partition profile on the HMC GUI.
  • A problem was fixed that caused the hypervisor to issue almost continuous reset/reload requests to the service processor.
System firmware changes that affect certain systems 
  • On systems with a F/C 5802 or 5877 I/O drawer attached, the firmware was enhanced to allow the drawer to power on with only one working offline converter assembly (OCA).
  • The firmware was enhanced to support the network installation of the IBM i operating system from the hardware management console (HMC) command line interface (CLI).
  • On systems using the IPv6 protocol, a problem was fixed that caused valid link local and unique link local addresses to be erroneously invalidated.  This prevented the port with that address from being used for network boot or network installation.

4.0 How to Determine Currently Installed Firmware Level

You can view the server's current firmware level on the Advanced System Management Interface (ASMI) Welcome pane. It appears in the top right corner. Example: EM350_038.

5.0 Downloading the Firmware Package

Follow the instructions on the web page. You must read and agree to the license agreement to obtain the firmware packages.

Note: If your HMC is not internet-connected you will need to download the new firmware level to a CD-ROM or ftp server.

6.0 Installing the Firmware

The method used to install new firmware will depend on the release level of firmware which is currently installed on your server. The release level can be determined by the prefix of the new firmware's filename.

Example: EMXXX_YYY_ZZZ

Where XXX = release level


Instructions for installing firmware updates and upgrades can be found at http://publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/ipha1/updupdates.htm

IBM i Systems

See "Server Firmware and HMC Wizard",
http://www-912.ibm.com/s_dir/slkbase.nsf/recommendedfixes

7.0 Firmware History

The Firmware History can be reviewed at the following url:

http://download.boulder.ibm.com/ibmdl/pub/software/server/firmware/EM-Firmware-Hist.html

8.0 Change History

Date
 Description
June 27, 2011 Removed older levels from the Firmware Information and Update Description table.  Corrected a typo in the firmware history html file (link in Section 7.0) for firmware level EM350_063.