IBM Storwize V7000 Unified ++++++++++++++++++++++++++ --------------------------------------------------------------------------------- CONTENTS 1. Introduction 2. Prerequisites 3. Code Levels 4. Problems Resolved and New Features 4.1 New features in IBM Storwize V7000 Unified File Module 1.6.2.4 4.2 APARs resolved in IBM Storwize V7000 Unified File Module 1.6.2.4 4.3 New features in Storwize V7000 7.6.1.9 4.4 APARs resolved in Storwize V7000 7.6.1.9 5. Further Documentation 6. Known Issues and Restrictions in this Level 7. Maximum Configurations 8. Supported Hardware 9. Pre-1.6.2.4 Release Information 9.1 Storwize V7000 Unified version 1.6.2.3 9.2 Storwize V7000 Unified version 1.6.2.2 9.3 Storwize V7000 Unified version 1.6.2.1 9.4 Storwize V7000 Unified version 1.6.2.0 9.5 Storwize V7000 Unified version 1.6.1.0 9.6 Storwize V7000 Unified version 1.6.0.1 9.7 Storwize V7000 Unified version 1.6.0.0 ---------------------------------------------------------------------------------- 1. Introduction This document contains important information about version 1.6.2.4 of the IBM Storwize V7000 Unified software. ---------------------------------------------------------------------------------- 2. Prerequisites Software Upgrade Test Utility: The software upgrade test utility "upgradetest" must be run within two hours of starting the upgrade. The upgrade test utility can be run as many times as required, but there must be a successful run of the upgrade test utility within two hours of starting the upgrade. Refer to the following URL for further information: http://www.ibm.com/support/docview.wss?uid=ssg1S4000986 Concurrent Upgrades: The concurrent upgrade (upgrade with I/O running) restrictions are documented at the following URL: http://www.ibm.com/support/docview.wss?uid=ssg1S1005471#_Restrictions_Upgrade If you are performing a concurrent code upgrade, first ensure that all host paths are available and operating correctly. System Performance: Performance of the IBM Storwize V7000 Unified will be degraded during the software upgrade process. IBM recommends you perform the upgrade at a time of lower overall I/O activity and when significant spikes in the system workload is not expected. Event Checking: Check there are no unfixed events in the event log. Use normal service procedures to resolve any events before proceeding. Asynchronous Replication Systems: If the system is part of an asynchronous relationship (either source or target), stop the replication to avoid asynchronous replication failures during upgrade. Refer to the following technote link to prepare for actions to be taken post upgrade if applicable http://www.ibm.com/support/docview.wss?uid=ssg1S1009686 Full upgrade compatibility matrix: Please see the following web page for the full upgrade compatibility matrix. http://www.ibm.com/support/docview.wss?uid=ssg1S1003918 ------------------------------------------------------------------------------------- 3. Code Levels Storwize V7000 Unified Software: Storwize V7000 Unified Product Version 1.6.2.4 (1.6.2.4-11) This includes Storwize V7000 (2076) Product Version: 7.6.1.9 (125.3.1805101027000) ------------------------------------------------------------------------------------- 4. Problems Resolved and New Features 4.1 New features in IBM Storwize V7000 Unified File Module 1.6.2.4: a) ECC (Electronic Customer Care) trust list file upgraded to V4. Please refer following link for more details on action needed to be taken: http://www-01.ibm.com/support/docview.wss?uid=ssg1S1012294 b) Auto deletion timeframe of core files from system is extended from 2 days to 4 days. c) Ability to re-enable async replication 'fast' encryption configuration using GUI and CLI (cfgrepl) after systems are upgraded to V1.6.2.1 or later. Refer to the following technote link for details: http://www.ibm.com/support/docview.wss?uid=ssg1S1009686 4.2 Issues resolved in IBM Storwize V7000 Unified File Module 1.6.2.4: Security Fixes For more information on the security fixes please refer to the flashes with "Security Bulletin:" in heading at below link(HIPER) http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified Critical Fixes HU01766 NFS user is unable to mount the share with samba export '%G' substitution variable. High Importance Fixes HU01768 After upgrade to 1.6.2.3, CIFS share permissions show invalid SID. HU01770 Both file modules reports message "descriptor_svcctl_OpenServiceW: Failed to get a valid security" due to issues in samba. HU01775 The network adapter stops abruptly without logging of events in the system and kernel logs show repeated message:"kernel: be2net 0000:0c:00.1: Unrecoverable Error detected in the adapter". HU01776 Test callhome fails with message "unknown communication error". HU01779 Improved logging to capture return value from V7000 upgrade. 4.3 New features in Storwize V7000 7.6.1.9: The following new features have been introduced in the 7.6.1.9 release: Distributed RAID Comprestimator Encryption for external virtualised storage IP Quorum New Volume CLIs GUI support for HyperSwap Support for VVols 16Gb 4port adapter Increase max number of iSCSI host attach sessions Remove 8G4 and 8A4 support CCU Checker updates User configurable max single IO time for Remote Copy Email setting allows '+' Enhance ET3 DPA log Customizable login banner Support for IBM Storwize V5000 Gen 2 4.4 Issues resolved in Storwize V7000 7.6.1.9: Hiper HU01479 The handling of drive reseats can sometimes allow IO to occur before the drive has been correctly failed resulting in offline mdisks. HU01505 A non-redundant drive experiencing many errors can be taken offline obstructing rebuild activity. Critical HU01490 When attempting to add/remove multiple IQNs to/from a host, the tables that record host-wwpn mappings can become inconsistent resulting in repeated node warmstarts across IO groups. HU01549 During a system upgrade HyperV-clustered hosts may experience a loss of access to any iSCSI connected volumes. HU01572 SCSI 3 commands from unconfigured WWPNs may result in multiple warmstarts leading to a loss of access. High Importance HU01480 Under some circumstances the config node does not fail over properly when using IPv6 adversely affecting management access via GUI and CLI. HU01488 SAS transport errors on an enclosure slot can affect an adjacent slot leading to double drive failures. HU01503 When the 3PAR host type is set to 'legacy' the round robin algorithm, used to select the mdisk port for IO submission to 3PAR controllers, does not work correctly and IO may be submitted to fewer controller ports, adversely affecting performance. HU01506 Creating a vdisk copy with the -autodelete option can cause a timer scheduling issue leading to node asserts. HU01569 When compression utilisation is high the config node may exhibit longer IO response times than non-config nodes. IT19726 Warmstarts may occur when the attached SAN fabric is congested and HBA transmit paths becomes stalled preventing the HBA firmware from generating the completion for a FC command. Suggested HU01098 Some older backend controller code levels do not support C2 commands resulting in 1370 entries in the Event Log for every detectmdisk. HU01228 Automatic T3 recovery may fail due to the handling of quorum registration generating duplicate entries. HU01332 Performance monitor and Spectrum Control show zero CPU utilisation for compression. HU01391 Storwize systems may experience a warmstart due to an uncorrectable error in the firmware. HU01430 Memory resource shortages in systems with 8GB of RAM can lead to node warmstarts. HU01609 When the system is busy, the compression component may be paged out of memory, resulting in latency that can lead to a warmstart. ----------------------------------------------------------------------------------- 5. Further Documentation The latest version of all IBM Storwize V7000 Unified documentation is available in the IBM Storwize V7000 Unified 1.6.0 Knowledge Center: http://www.ibm.com/support/knowledgecenter/ST5Q4U/landing/v7000_unified_welcome.htm?lang=en Selected documents are available for download in PDF format from the support website: http://www.ibm.com/storage/support/storwize/V7000/unified Please refer to below link for a consolidated list of highly recommended reference material on IBM Storwize V7000 Unified http://www-01.ibm.com/support/docview.wss?uid=ssg1S1004460 ----------------------------------------------------------------------------------- 6. Known Issues and Restrictions in this Level * In IBM Storwize V7000 Unified systems with V1.6.2.0 and onwards, to address security vulnerability as per CVE 2016-2183, cipher 'arcfour' is disabled by default. This would result in async replication for filesystem configured with 'fast' encryption method to fail and action needs to be taken to restore the function. Refer to the below technote for more information on this issue: http://www.ibm.com/support/docview.wss?uid=ssg1S1009686 * After upgrade, NDMP backups may start failing and may not get resolved even by restarting the NDMP backup jobs. Please contact IBM support for further assistance or refer to the below technote for more information on this issue: http://www-01.ibm.com/support/docview.wss?uid=ssg1S1009338 * SMB 1.0 is deprecated from current and all future versions of IBM Storwize V7000 Unified. NOTE: SMB 1.0 still works on all versions of IBM Storwize V7000 Unified. * SMB protocol version restrictions (max_protocol parameter) : * Systems upgrading from 1.5.x.x code level to 1.6.0.1, or later will have SMB 3.0 (max_protocol parameter) disabled by default. Enabling SMB 3.0 on the V7000 Unified requires a change window with an outage as it is a non-concurrent procedure requiring specific actions to be taken on the windows client side. For further details please contact IBM support. * Systems which are first time installed with 1.6.0.0 or later code levels will have SMB 3.0 (max_protocol parameter) enabled by default and can be used without any restrictions. * Systems upgrading from 1.6.0.0 to this code level will have SMB 3.0 (max_protocol parameter) enabled by default and may be used without any restrictions. * In IBM Storwize V7000 Unified, Windows 8 with offline folders is not currently supported. * Browsers with below listed levels are certified for using the IBM Storwize V7000 Unified Management GUI. Mozilla Firefox 38 Mozilla Firefox Extended Support Release (ESR) 38 Important: All Firefox users should upgrade to these updated packages, which contain Firefox version 38.x ESR. After installing the update, Firefox must be restarted for the changes to take effect. For Red Hat Linux users, make sure all previously released errata relevant to your system have been applied before applying this update. This update is available at the Red Hat Network: https://rhn.redhat.com/errata/RHSA-2015-1982.html Details on how to use the Red Hat Network to apply this update are available at https://access.redhat.com/knowledge/articles/11258 Microsoft Internet Explorer (IE) 10 and 11 Google Chrome 41 Later versions of the browsers are supported as long as the vendors do not remove or disable functionality that the product relies upon. For browser levels higher than the levels that have been certified with the product, customer support will accept usage-related and defect- related service requests. As with operating system and virtualization environments, if IBM support cannot recreate the issue in our lab, we may ask the client to recreate the problem on a certified browser version in order to determine if a product defect exists. Defects will not be accepted for cosmetic differences between browsers or browser versions that do not affect the functional behavior of the product. If a problem is identified in the product, defects will be accepted. If a problem is identified with the browser, IBM may investigate potential solution or work-around that the client may implement until a permanent solution becomes available. * In IBM Storwize V7000 Unified, quarantined folders are only accessible with the root ID. This restriction will be lifted in a future IBM Storwize V7000 Unified release. Refer to the below technote for more information on this issue: http://www-01.ibm.com/support/docview.wss?uid=ssg1S1004078 For more details please refer to the V1.6 Configuration Limits and Restrictions for IBM Storwize V7000 Unified for product restrictions that currently apply: http://www.ibm.com/support/docview.wss?uid=ssg1S1005471 * If using IP replication, please review the set of restrictions published in the V7.6 Configuration Limits and Restrictions document. * Intra-Cluster Global Mirror Not Supported Refer to the following flash for more information on this restriction: http://www.ibm.com/support/docview.wss?uid=ssg1S1003725 * SAN Volume Controller Inter-cluster Metro Mirror and Global Mirror Compatibility Cross Reference Refer to the following flash for more information on this restriction: http://www.ibm.com/support/docview.wss?uid=ssg1S1003646 Once the software upgrade process has been started, the management GUI automatically refreshes to display the progress of the upgrade. During the upgrade each file module will be restarted, resulting in a fail-over and fail-back of the management services, including the GUI. After a fail-over has occurred it may be necessary to manually refresh/reload the page in the web browser in order to reconnect with the new active management node and login again. If an IBM Storwize V7000 Unified Code Upgrade Stalls or Fails then contact IBM Support for further assistance http://www.ibm.com/support/docview.wss?uid=ssg1S1002894 -------------------------------------------------------------------------------------- 7. Maximum Configurations The maximum configurations for IBM Storwize V7000 Unified 1.6.2.4 are documented in the V1.6 Configuration Limits and Restrictions for IBM Storwize V7000 Unified document which is available from: http://www.ibm.com/support/docview.wss?uid=ssg1S1005471#_MaximumConfigurations -------------------------------------------------------------------------------------- 8. Supported Hardware This release of IBM Storwize V7000 Unified software is supported on the following hardware types: File Modules: * 2073-700 * 2073-720 Storwize V7000 Control enclosures: * 2076-112 * 2076-124 * 2076-312 * 2076-324 * 2076-524 Storwize V7000 Expansion enclosures: * 2076-212 * 2076-224 * 2076-12F * 2076-24F --------------------------------------------------------------------------------------- 9. Pre-1.6.2.4 Release Information 9.1 Storwize V7000 Unified version 1.6.2.3 Code Levels: Storwize V7000 Unified Product Version 1.6.2.3(1.6.2.3-12) Storwize V7000 (2076) Product Version 7.6.1.8 (125.3.1707131751000) New features in IBM Storwize V7000 Unified File Module 1.6.2.3: Ability to re-enable async replication 'fast' encryption configuration using GUI and CLI (cfgrepl) after systems are upgraded to V1.6.2.1 or later. Refer to the following technote link for details: http://www.ibm.com/support/docview.wss?uid=ssg1S100968 Issues resolved in IBM Storwize V7000 Unified File Module 1.6.2.3: Security Fixes For more information on the security fixes please refer to the flashes with "Security Bulletin:" in heading at below link(HIPER) http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified Critical Fixes HU01668 NFSv4 core dumps unexpectedly due to internal race condition. HU01676 After upgrade to 1.6.2.x, access to NFS shares fails with message "The file access permissions do not allow the specified action". HU01685 NFS shares unmount due to missing entries in /etc/exports, Enable quick way to restore the missing export definitions by ensuring the exports are only deactivated rather than deleted in case of a mismatch between internal registry and management database. High Importance Fixes HU01641 Upgrade from 1.5.x to 1.6.2.x failed at 'mmstartup' after node reboot. HU01642 While adding users to CIFS shares, CLI 'chexport' fails with message "domain user or group not found". HU01643 Upgrade failed with error message "Error removing sofs-toolset package on mgmt002st001". HU01644 After upgrade to 1.6.2.1, CLI 'querybackup' display greek characters incorrectly. HU01652 winbind fails to authenticate child domain of a trusted domain, hence CIFS users from trusted domain cannot authenticate to the system. HU01656 V7000 Unified upgrade failed with error code '01B4' at task U005cluster_upgrade_attached_storage' due to V7000 block code upgrade taking longer time than an internal defined timeout. HU01663 Additional explanation and alternative solution provided for the warning message "USERMESSAGE:WARNING:This upgrade will remove CIMOM from the v7000 Unified file modules" displayed by the upgradetest utility during upgrade from code levels earlier than 1.5.1.0. HU01674 GUI displays a pop up window every 30 seconds which says "The server was unable to process the request". HU01680 System reports multiple messages for connection loss in system log for transient network glitch. HU01681 After upgrade, 'lsquota' CLI does not display information correctly. HU01682 'lsquota' times out with error message 'EFSSG0002I Command exception found: TimeoutException'. HU01683 Upgrade fails due to active node having '/var' space 100% full. HU01684 Detailed guidance added to the log file for the backup log snippet "Some changed files will be skipped to avoid HSM recall". This will advise the administrator when referring to the log file in response to a backup failure with message: "Backup job reports "EFSSA0797C Backup partially failed. Please check the logs for details". HU01686 Management node crashed during upgrade at system reboot displaying message "1710 bus error". 9.2 Storwize V7000 Unified version 1.6.2.2 Code Levels: Storwize V7000 Unified Product Version 1.6.2.2(1.6.2.2-18) Storwize V7000 (2076) Product Version 7.6.1.7 (125.2.1702091228008) New features in IBM Storwize V7000 Unified File Module 1.6.2.2: Ability to re-enable async replication 'fast' encryption configuration using GUI and CLI (cfgrepl) after systems are upgraded to V1.6.2.1 or later. Refer to the following technote link for details: http://www.ibm.com/support/docview.wss?uid=ssg1S1009686 Issues resolved in IBM Storwize V7000 Unified File Module 1.6.2.2: Security Fixes For more information on the security fixes please refer to the flashes with "Security Bulletin:" in heading at below link(HIPER) http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified Critical Fixes HU01585 High rate of 'gss_init_sec_context failed' message in system logs accompanied by performance degradation or access loss. HU01557 Access to the system may be lost under certain conditions while CTDB is revoking READONLY delegations. HU01599 Node asserts causing filesystem to go offline due to GPFS internal log recovery after node reboot. High Importance Fixes HU01576 Multiple execution of 'lsexport' on systems configured with large number of NFS shares, floods system log with message 'EFSSG0745C Database temporarily not available. Cause: Too many open connections'. HU01577 Migration policy created for fileset with CLI cannot be managed from GUI. HU01588 NFSv4 enters defunct state while shutting down causing access loss to NFSv4 shares. HU01589 After upgrade, username and groupname is seen as 'nobody' causing NFS shares to not mount HU01580 HSM intermittently fails to recall files accessed via CIFS shares on systems running V1.6.x. HU01604 After upgrade, VFS call takes unexpectedly long time resulting in slowness while accessing CIFS shares. HU01562 Directory creation from windows client applications such as Eclipse and notepad++ may return permission denial. HU01587 NFS was not able to startup after CTDB restart. HU01591 IBM Storwize V7000 Unified upgrade test utility check for exposure to a GPFS deadlock during quota files conversion on a system running V1.6.0.x. HU01590 During upgrade from V1.5.x to V1.6.2.1, some user's may experience permission denial while accessing CIFS shares. HU01594 IBM Storwize V7000 Unified upgrade test utility check for close to full /var on active management node to warn about potentially risk to system upgrade failure. HU01592 System upgrade to V1.6.2.1 may fail while updating authentication due to a missing setting in CTDB config file. HU01558 Domain users can authenticate to CIFS but not able to log in to FTP. HU01567 IBM Storwize V7000 Unified upgrade test utility V11.5 does not recognize newer V7000 disks. HU01574 After system upgrade to V1.6.2.1, severe performance degradation is observed on heavily loaded systems due to large number of 'getpwuid' invocations upon every 'auth' and 'create_file' calls from CIFS users. HU01575 Upgrade failed with error '019A' at task 'U040 node_update_packages'. HU01595 After system upgrade to V1.6.2.1, System logs gets flooded with message: "kernel: lockd: unexpected error 11 in nlmsvc_grant_blocked!". HU01596 After CTDB package upgrade, NFSv4 shares could not be mounted using public IP's due to overwriting of some config files. HU01597 On AIX CIFS clients, 'df' command reports a larger number of available space than the actual space available in the share. HU01600 During system upgrade to V1.6.2.1, IBM Storwize V7000 Unified upgrade test utility report errors which are more than 30 days old. HU01601 ibmsdduu tool when used with a proxy fails to upload data and reports message: "java.io.IOException: Proxy tunnel setup failed: HTTP/1.1 403 Forbidden". HU01603 After deleting NFSv4 shares, nfsd daemon exits on one of the node and does not restart. Suggested Fixes HU01593 Update GUI help panel with more information on SSL certificates. HU01598 Update man page for 'chwache' CLI under option '--disablewcache' with restrictions for conversion of independent and single writer wcache filesets to normal filesets. HU01605 After system upgrade to V1.6.2.1, System logs non informational message "Freed frame ../source3/winbindd/winbindd_dual_ndr.c:318, expected .. /source3/lib/tldap.c:1981". 9.3 Storwize V7000 Unified version 1.6.2.1 Code Levels: Storwize V7000 Unified Product Version 1.6.2.1(1.6.2.1-17) Storwize V7000 (2076) Product Version 7.6.1.5 (125.1.1608221542000) New features in IBM Storwize V7000 Unified File Module 1.6.2.1: Ability to re-enable async replication 'fast' encryption configuration using GUI and CLI (cfgrepl) after systems are upgraded to V1.6.2.1 or later. Refer to the following technote link for details: http://www.ibm.com/support/docview.wss?uid=ssg1S1009686 Issues resolved in IBM Storwize V7000 Unified File Module 1.6.2.1: Security Fixes For more information on the security fixes please refer to the flashes with "Security Bulletin:" in heading at below link(HIPER) http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified Critical Fixes HU01407 After upgrade, filesystem having async replication configured with 'fast' encryption method fails. Note: Refer to section 4.1 for actions to be taken post upgrade. HU01433 Callhome function fails in V1.6.1.0 / V1.6.2.0 HU01439 After adding/deleting/editing NFS export, NFS services may fail to start due to conflict between CNSM and CTDB monitoring. HU01453 High rate of 'gss_init_sec_context failed' message in system logs accompanied by performance degradation or access loss. High Importance Fixes HU01440 After upgrade, some CIFS share users may get 'Permission denied' and 'No space on disk' error messages while accessing files, directories having long ACLs. HU01417 Fileset creation with multi-byte character set (MBCS) fails. HU01421 Fileset creation fails when invoked by 'root' user. HU01419 'mkexport' fails leaving stale entries in '/etc/exports', provoking CTDB to mark the node as unhealthy. HU01422 Winbind logs false positive message as "Failed to find domain NT AUTHORITY". IT18743 'wbinfo' fails to fetch user info, resulting in ID mappings denial for users belonging to trusted domains. HU01423 The domain admin user may not be able to login to GUI but can login to CLI. HU01425 AIX and IRIX NFS client fails to create file or directory in a share, where parent directory has SETGID bit set. HU01427 NFS access to files within a snapshot fails under certain conditions. HU01406 After upgrade, VFS call takes unexpectedly long time resulting in slowness while accessing CIFS shares. HU01408 After upgrade from V1.5x to V1.6.2.0, access to CIFS share is slow due to samba panic. HU01437 'restripefs' fails with error message 'EFSSG0002I Command exception found: null', when total number of GPFS internal PIT worker threads of all participating node is more than 31. HU01441 After node reboot, CTDB could not be started due to NFS failure. HU01443 Async replication takes long time to complete when default quota is used. HU01444 'lsquota' times out with error message 'EFSSG0002I Command exception found: TimeoutException'. HU01436 Quota limits don't change after files are deleted. HU01448 Callhome does not offload cndump data to ecurep for M4 nodes. HU01452 HSM intermittently fails to recall files accessed via CIFS shares on systems running V1.6.x. Suggested Fixes HU01438 Improved Knowledge center description for 'chexport' CLI for option '-hide snapdirs'. 9.4 Storwize V7000 Unified version 1.6.2.0 Code Levels: Storwize V7000 Unified Product Version 1.6.2.0(1.6.2.0-37) Storwize V7000 (2076) Product Version 7.6.1.5 (125.1.1608221542000) New features in IBM Storwize V7000 Unified File Module 1.6.2.0: Antivirus: Added support for Kaspersky Scan Engine. Added support for Symantec protection engine for network attached storage (SPENAS) 7.8 in IBM Storwize V7000 Unified. CLI based support for restoring entire Filesystem from a snapshot. Added 'NFS_Commit' as the default setting for NFSv4.0 server to improve performance for small writes workload from VMWare ESX NFS clients. Issues resolved in IBM Storwize V7000 Unified File Module 1.6.2.0: Security Fixes For more information on the security fixes please refer to the flashes with "Security Bulletin:" in heading at below link(HIPER) http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified Critical Fixes HU01613 NFS shares losses access to filesets on AFM cache system due to failure of AFM recovery process triggered while connecting to home. HU01285 File module loses AD connection when Varonis polls via 'wbinfo -u' and 'wbinfo -g'. HU01311 Restoration of filesystem from TSM backup fails when encountering special character in file or path name. HU01296 During upgrade, some Windows hosts may lose access as they attempt to connect using SMB3.0. HU01294 During upgrade management node network is shutdown while upgrading Emulex adapter driver. HU01306 During upgrade CTDB shuts down while upgrading samba packages causing CIFS access disruption. HU01278 After upgrade, NFS share data is not accessible to members of domain users group. HU01289 Restoration of filesystem from TSM backup fails when invoked with special character in target path. High Importance Fixes HU01293 Upgrade fails while updating Emulex driver if adapter is bonded but not connected. HU01297 'lshsm' CLI does not report correct summary of all hierarchical storage management (HSM) enabled file systems in the cluster. HU01307 GUI displays incorrect timestamp for NDMP events. HU01277 GUI displays blank or default values for warning and error threshold for fileset quota. HU01308 GPFS does not configure 'filesetdf' automatically for fileset that have quota checking enabled. HU01295 GUI is not accessible after Java Virtual Machine running the management stack run out of memory and is terminated with entry of 'EFSSA0151C' error in system logs. HU01288 NSD mapping correction fails with error messages from 'IBM2073_INSTALL_NSD_REPAIR_FIX' script. HU01310 CTDB traverse events floods event logs and degrades system performance. HU01273 During node reboot, 'resumenode' CLI fails with false messages stating 'All required Filesystem not mounted' and makes GUI inaccessible. HU01303 Custom policy does not fetch correct information when applied with two node names as parameters instead of one. HU01284 Winbind floods the log file with repetitive messages degrading the system performance. HU01286 'lstask' reports error for 'BackupMgmtNode' and 'StartRunPolicy'. HU01334 After upgrade, 'lsquota' CLI may timeout or not list any output. HU01280 Single node crash due to assert in GPFS while waiting on a mutex for 'OpenFile structure'. HU01275 The management console IP does not match between the IBM Storwize V7000 and the IBM Storwize V7000 Unified. HU01290 System reports frequent warning messages stating 'defunct HSM daemon(s) detected'. HU01329 CTDB gets unhealthy due to NFS service failure. Suggested Fixes HU01299 System logs a warning message when the maximum number of prefetch calls for NDMP is exceeded. HU01301 NFSv4 client is unable to view the directory if another client is directly mounted to it. HU01265 After upgrade, system reports error stating 'Nfs ganesha exportpath was not found' even when NFSv4 is not in use. 9.5 Storwize V7000 Unified version 1.6.1.0 Code Levels: Storwize V7000 Unified Product Version 1.6.1.0(1.6.1.0-44) Storwize V7000 (2076) Product Version 7.6.0.4 (122.23.1602250020000) New features in IBM Storwize V7000 Unified File Module 1.6.1.0: Added support for Windows 10 as SMB client. Support for Storwize V7000 Gen2 systems configured with one or two quad 16GB Fibre Channel adapters. Allow separate permissions (ACLs) for Write Data, Create File and Create Folder, Append Data. Optimized Power-Saving Settings on M4 servers to reduce CPU usage. Issues resolved in IBM Storwize V7000 Unified File Module 1.6.1.0: Security Fixes For more information on the security fixes please refer to the flashes with "Security Bulletin:" in heading at below link(HIPER) http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified Critical Fixes HU01243 GPFS assert during snapshot delete results in file module node crash. HU01211 Access loss may be experienced during an upgrade of a system having fileset configured as AFM cache, due to problems in the AFM recovery code path that is indirectly triggered by unnecessary AFM operations from cnscm. HU01199 After upgrade users associated with the trusted domain could not access the system. This exposure existed in cases where the Unified did not have direct network connectivity to the trusted domain. HU01200 After upgrade to 1.6.0.x admin users were not able to authenticate and access shares. HU01203 After upgrade to 1.6.0.x remote admin users authenticated with AD server were unable to login to the system CLI or GUI. HU01204 Users were not able to access the shares due to snapshot related deadlock in GPFS. This exposure exists after upgrade to V1.6.0.x when snapshots created on V1.5.x and V1.6.0.x coexist on the system. HU01129 Client unable to access the system because of CTDB unhealthy on all nodes. HU01150 Process smbd terminates after CTDB timeout. HU01133 NFSv4 server exits on locks out of sync causing NFS services to stop. HU01168 After upgrade access to CIFS shares is lost on the system when the number of ranges for AUTO ID mapping is less than 3 for plain AD authentication configuration when default configuration settings for AUTO ID pool are overridden. High Importance Fixes HU01207 Repeated INFO messages indicating a restart of vsftpd service, such as "A start service was detected with vsftpd" and "A stopped or failed service was detected with vsftpd". HU01217 After upgrade parent filesystem free space reported instead of fileset when fileset quotas are enabled. HU01196 Creating Filesytem using system GUI with owning group option fails. HU01202 System node becomes unhealthy due to false positive result during internal validation of NFS Ganesha export paths. HU01197 SVC command user credentials gets logged in Unified log file. HU01154 Excessive SS0010 and SS0011 events causes GUI to crash. HU01123 Java runs out of memory and generates core dump causing GUI to crash. HU01113 While upgrading V7000 Unified an access outage may occur due to node ban. HU01146 Upgrade failed with error 01A8 at task U020cluster_upgradenode_all. HU01148 System fails Nessus security scan with TCP port 443 and 1081 vulnerabilities. HU01152 Upgrade failed with error 01E4 at task U035cluster_hsm_policy_upgrade. HU01138 Upgrade failed with error 01E0 at task U010cluster_hsm_upgrade. HU01117 After upgrade the lsnwinterface CLI does not display vlan ip information. HU01170 Running nmap makes the CLI server inadvertently process the nmap requests incorrectly eventually leading to CTDB marking the node unhealthy. HU01173 Callhome generates multiple cndump logs due to timezone offset difference. HU01175 GPFS mmapplypolicy command failure due to a race condition when several simultaneous policy sessions are invoked through operations such as triggering multiple NDMP backup sessions in parallel. HU01164 GUI is incorrectly displaying fileset quota limits inherited from filesystem even though the 'per fileset' quota option is enabled. Suggested Fixes HU01201 After upgrade to V1.6.0.x, lsidmap incorrectly displays EFSSG1145W Warning: "EFSSG1145W Warning: Some domain or SID information is not available. Verify AD domains connectivity with the cluster" HU01135 Unscannable files are continuously being resent for antivirus scanning which can affect antivirus performance. HU01215 Support Package creation collects SVC snaps twice impacting system performance. 9.6 Storwize V7000 Unified version 1.6.0.1 Code Levels: Storwize V7000 Unified Product Version 1.6.0.1(1.6.0.1-11) Storwize V7000 (2076) Product Version 7.5.0.3 (115.51.1509171734000) New features in IBM Storwize V7000 Unified File Module 1.6.0.1: None Issues resolved in IBM Storwize V7000 Unified File Module 1.6.0.0: Critical Fixes HU01025 Upgrade to V1.6.0.0 may result in access being denied to SMB/CIFS shares immediately after upgrade. This is seen only under certain access patterns. If the access issue is not encountered upon upgrade or has been resolved, this exposure no longer exists on a system running fine at 1.6.0.0 code level. For more information on the security fixes please refer to the flashes with "Security Bulletin" in heading at below link(HIPER): http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified 9.7 Storwize V7000 Unified version 1.6.0.0 Code Levels: Storwize V7000 Unified Product Version 1.6.0.0(1.6.0.0-70) Storwize V7000 (2076) Product Version 7.5.0.3 (115.51.1509171734000) New features in IBM Storwize V7000 Unified File Module 1.6.0.0: Support filesetdf option for filesystems - Allows the end users to see quotas associated with the fileset, rather than that of the entire filesystem, when checked with "df" command from linux system. Microsoft Management Console (MMC) Support (Shared-Folders Snap-In) - Allowing Storage Admins to access and use Storwize Unified via the popular MMC. RPQ only - Support VARONIS file audit agent (3rd party software) allowing File Audit capabilities on Storwize Unified. Support CIFS on virtualised block controllers Support SMB v3 protocol Support "SMB encryption" feature of SMB 3 protocol - Allowing encryption "in-flight" versus "at-rest". Includes Spectrum scale 4.1.1.2 Includes NFS Ganesha 2.2 Add CLI support to define snapshot deletion time while defining retention rules. Support for GPFS ACL mode chmodAndUpdateAcl Snapshots for SMB clients Emulex Firmware and support new variant of Emulex 10G card Issues resolved in IBM Storwize V7000 Unified File Module 1.6.0.0: Critical Fixes HU00971 Log kernel stack when NFS Ganesha process exits and gets stuck in zombie state. HU00979 Samba process gets killed on both node one after the other. HU01012 NSD mapping correction failed while running upgrade. High Importance Fixes HU00976 GUI is showing task "1 Drive Upgrade operations". HU01013 Error message "The server was unable to process the request" detected after trying to access the File System section in Unified GUI. HU01015 While running an upgrade, all ctdb nodes were marked as unreachable. Suggested Fixes HU00978 Misleading WARNING, SEVERE messages when 'mmremote mmgetstate' returns an empty token. HU00985 Email Recipients on GUI not working on "INFO". HU01010 Unable to verify correct software version failure during upgrade. This Storwize V7000 Unified 1.6.0.0 release contains security fixes. For more information on the security fixes please refer to the flashes with "Security Bulletin" in heading at below link(HIPER): http://www-947.ibm.com/support/entry/portal/alerts/hardware/system_storage/disk_systems/mid-range_disk_systems/ibm_storwize_v7000_unified