Readme for IBM Flex System EN4054 4-port 10Gb Ethernet Adapter

08/14/2013: See Document Change History for details on changes to this document.

Contents

1.0 Overview

This update contains the AIX RPM file for the current level of microcode for the IBM Flex System EN4054 4-port 10Gb Ethernet Adapter, Feature Code 1762. This is a multiport adapter with two ASICs. Each ASIC requires it’s own microcode update. To update the microcode for the entire adapter, all of the adapter resources (ports) need to be updated to ensure both ASICs are updated.

 Back to Contents

2.0 Adapters Affected

This microcode is for feature code 1762: Option PN 81Y3124: CCIN 2B5D,  Asm PN 81Y3126 

To determine the part number of the adapter on an AIX system, on the command line key the following command:

lscfg -vl entX              where entX represents the adapter

Affected adapters will be listed as: 10GbE 4-port Mezzanine Adapter (a2191007df1033e7)

To determine the presence of this adapter on a Linux system, on the command line key in:

lspci -nn

Affected adapters will be listed as: Emulex Corporation OneConnect 10Gb NIC (be3) [19a2:0710]

The typical time to install the microcode is 0.4 hr.

 Back to Contents

3.0 Microcode Description and Revision History

Microcode Level

Changes

0400602810008

Fix config Patterns cannot configure bandwidths on Emulex   CN4054 Adapter from Virtual Fabric Mode to Switch Independent with single deployment/reboot <code change>

Fix ports are disappearing in the Storage (UEFI) when try to Reconnect Devices with IBM1212-24.1 <code change>

0400104220000

This is the level of microcode that is initially supported when it became generally available.

The Firmware Levels Below Are No Longer Supported
Please Update To The Latest Level At Your Earliest Convenience

 

 

 

 

Back to Contents

4.0 Cautions and Important Notes

The microcode installation does NOT support concurrent download while the ent resources are available for use. If the ent resources are in use, they must manually be released prior to starting the download. Failure to do so will result in a message instructing that the ent resource be freed.

NOTE: It is recommended that the installation be scheduled during a maintenance window or during non-peak production periods.

The Service Packs can be obtained from the IBM Fix Central website located at http://www.ibm.com/eserver/support/fixes.

 

 

The management module obtains the firmware version by reading a EEPROM memory module on the adapter.  On the reboot following a firmware update the two network controllers of the adapter arbitrate for their chance to update the firmware information stored in the memory module. On some firmware update, it may require two reboots before both controller successfully update the EEPROM memory module.

The adapter uses the second or the MAC+1 port address for LLDP/DCBX (Link Layer Discovery Protocol)/(Data Center Bridging eXchange) link exchange.  The  DCBX engine is built into the network controller ASIC for FCoE and is always active although FCoE is not supported. This MAC+1 address remains constant and is not changed with OFM.  The forwarding data base of the switch will show the Ethernet Base port MAC + 1 address value. A user may expect to only see the port Base MAC address.  This is a potential point of confusion for a user who is unaware of the reason why the base MAC+1 address is present.


Back to Contents

5.0 To Determine Adapter Microcode Levels

Before installing the microcode, it is important to determine the current microcode level of the adapter.

5.1 AIX Systems

1.  List the Ethernet adapters installed in the system by typing on the command line:

lsdev | grep -e ent

Note the names of all the Ethernet adapters installed. The adapters will be identified as: 10GbE 4-port Mezzanine Adapter. The adapter names will be entX, where X is 0, 1, or some other number.

2.  Determine the current microcode level on the adapter by typing on the command line:

lsmcode -d entX

where X is the number of the adapter's port returned from the "lsdev" command above.

A screen similar to the following will be displayed:

DISPLAY MICROCODE LEVEL                                            802111
ent0 PCIe2 4-port 10GbE Mezz Adapter (a2191007df1033e7)


The current microcode level is 0400602810008.


Use Enter to continue.



F3=Cancel F10=Exit Enter

 

If the current microcode level is not 0400602810008, then the microcode image on the adapter is not at the latest level.

Back to Contents

5.2 Linux Systems

1)  List the Ethernet adapters installed in the system by typing:

    #ifconfig -a | grep eth

Note: All of the Ethernet adapters that are installed will be displayed. They will be listed as ethX, where X is 0, 1, etc.

2) Use ethtool -i ethX to display the microcode level for each device.

If the firmware-version is not 4.1.422.0, then the firmware on the adapter is not at the latest level.

Back to Contents

6.0 Install RPM Package

6.1 AIX RPM Package

Use this method to install the AIX RPM package on an AIX system. Note that the commands are case sensitive and must be entered exactly as shown, including file names. Installing the RPM places the binary file a2191007df1033e7.0400602810008 into the /etc/microcode directory.

1. If the /etc/microcode directory does not exist, make a directory to receive the RPM format file. On the command line type:

mkdir /etc/microcode

2. Transfer the RPM format file, a2191007df1033e7.0400602810008.aix.rpm to any temporary directory on the target system.

3. Unpack the file. On the command line type:

rpm -ihv --ignoreos a2191007df1033e7.0400602810008.aix.rpm

4. If the microcode package unpacks successfully, the microcode file will be added to the /etc/microcode directory.

If a message is received saying the "package <package_name> is already installed", you will need to uninstall the rpm package. On the command line type:

rpm -e <package_name>

where <package_name> is the name of the package that was returned in the message. Return to step 3 and attempt to unpack the file again.

            5. To complete the update go to section 7.0.

Back to Contents

6.2 Linux using the Standalone Diagnostics CD

Below are references and the general flow on how to update microcode update via CD

1) Boot the system via a Standalone Diagnostic's CD

a) To create a bootable Diagnostic's CD go to the following URL.

http://www.software.ibm.com/webapp/set2/sas/f/diags/home.html

b) After booting to Standalone Diagnostics, the Diagnostic's CD can be removed.

2) The Diagnostic's CD should be replaced by a CD containing the unpacked microcode image(s).

The CD containing the microcode images should be prepared prior. This can be done by taking the a2191007df1033e7.0400602810008.aix.rpm file(s) and unpacking them on a usable server. The unpacked files can then be burned on to the CD media.

 

Back to Contents

7.0 Installing the Adapter's Microcode

7.1 Using the AIX Command-Line Method

Login as root user. From the command line key in:

diag -d entX -T download
where X is the port on which you want to install the microcode.

Self-explanatory menus will step you through the microcode installation. All of the ent resources needs to be updated for the entire adapter to be updated.

Back to Contents

7.2 Using the Diagnostic Service Aid Method

Login as root user.
From the command line key in:  diag
Select:  Task Selection (Diagnostics, Advanced Diagnostics, Service Aids, etc.)
Select:  Microcode Tasks
Select:  Download Latest Available Microcode
Select:  file system
          /etc/microcode
Select the device:  ent*
Press enter when prompted to download the microcode.
All of the ent resources needs to be updated for the entire adapter to be updated.

Upon completion, a message will state that the microcode has been successfully downloaded and that
the new level is 0400602810008.

Back to Contents

8.0 Verifying the Update

8.1 Verifying the Update on AIX

1.  List the Ethernet adapters installed in the system by typing on the command line:

lsdev | grep -e ent

Note the names of all the Ethernet adapters installed. The adapters will be identified as 10GbE 4-port Mezzanine Adapter (a2191007df1033e7). The adapter names will be entX, where X is 0, 1, or some other number.

2.  Determine the current microcode level on the adapter by typing on the command line:

lsmcode -d entX

where X is the number of the adapter's port returned from the "lsdev" command above.

A screen similar to the following will be displayed:

DISPLAY MICROCODE LEVEL                                            802111
ent0 PCIe2 4-port 10GbE Mezz Adapter (a2191007df1033e7)


The current microcode level is 0400602810008.


Use Enter to continue.



F3=Cancel F10=Exit Enter

If the current microcode level is 0400602810008, then the microcode has been updated.
 

Back to Contents

8.2 Verifying the Update on Linux

1)  List the Ethernet adapters installed in the system by typing:

    #ifconfig -a | grep eth

Note: All of the Ethernet adapters that are installed will be displayed. They will be listed as ethX, where X is 0, 1, etc.

2) Use ethtool -i ethX to display the microcode level for each device.

If the current microcode level is 4.1.422.0, then the microcode has been updated.

 Back to Contents


Document Change History

Date

Change

05/09/2012

Initial Document

08/14/2013

Update with firmware 0400602810008

 Back to Contents


Apendix: Vendor Firmware Notice

                               Emulex (R) Corporation
                                    Software Kit
                                  4.0.1 Build 27.1
 
 
                                   RELEASE  NOTES
                                   ==============
 
 
Summary
=======
 
This is a release candidate of Emulex 4.0.1 drivers and firmware for UCNA
and Fibre Channel adapters.
 
 
Known Issues
============
 
Please see the Change History document for a list of fixes in this kit.
 
 
Hardware Compatibility
======================
 
This release of firmware will support the following adapters:
 
Adapter            ASIC       Name / FRU
 
OCm11104-N-P       BE3        Wildcat-P NIC / 90Y3553
 
 
Firmware Packages
=================
 
The following are the firmware image names provided in this kit along with
descriptions for what adapter each image should be used for. It is important
to use the correct image for the adapter being used. 
 
BE3
===
 
OneConnect-Flash-4.1.422.0-IBM-PPC.iso
 - Offline flash ISO image for System-P BE3 adapters
 
 
Contents of Package
===================
 
Product                                 Version        Previous Release
 
BladeEngines (UCNA) Firmware            4.1.422.0      4.1.422.0
Universal Boot Package                  7.05a1         7.05a1
  x86 BootBIOS                          4.03a0         4.03a0
  FCoE FCode                            4.01a1         4.01a1
  UEFIBoot                              5.01a15        5.01a15
PXEBoot UEFI NIC                        4.1.422.0      4.1.422.0
iSCSI UEFI                              4.1.422.0      4.1.422.0
 
 
 

Privacy | Legal | Contact IBM