*IBM eServer *

*PCI-XDDR Quad Channel U320 SCSI RAID Adapter
CCIN:  571E, 571F
*

 DATE: Dec 03, 2012

 

*Table of Contents*

*1.0 Microcode Change History <#1.0>*

*2.0 General Information <#2.0>*
*2.1 Installation Time <#2.1>
**2.2 Machine's Affected <#2.2>
**2.3 AIX Requirements <#2.3>
**2.4 Linux Requirements <#2.4>*

*3.0 Determine the Current Microcode Level for AIX <#3.0>
**3.1 Determine the Current Microcode Level for Linux <#3.1>*

*4.0 Downloading and Unpacking the Firmware Update Package from CORE
<#4.0>*
*4.1 Downloading the RPM Format File to the Target Server <#4.1>*
*4.2 Discovery Tool Microcode CD-ROM creation and download instructions
<#4.2>*

*5.0 Verifying microcode before download and notes <#5.0>*
*5.1 Microcode Download Procedure-PCI-XDDR Quad Channel U320 SCSI RAID
Adapter for AIX <#5.1>
**5.2 Microcode Download Procedure-PCI-XDDR Quad Channel U320 SCSI RAID
Adapter for Linux <#5.2>*

*6.0 Microcode Readme Change History <#6.0>*

*=====================================================================================*


*1.0 Microcode Change History:*
 
0715002a 	-Contains fixes for all known issues

0715000d

	

-iSeries enhancement for all U320 SCSI Controllers. Enhancement to
recognize Hot Spare (RAID 0) DASD.
-GA microcode level necessary for SCSI RAID AUX Cache Card Support.


*2.0 General information*

SUBJECT: PCI-XDDR Quad Channel U320 SCSI RAID Adapter

******* PLEASE READ THIS ENTIRE NOTICE *********

* 2.1 Installation Time:*
Approximately 30 minutes
 
*2.2 Machine's Affected:*
iSeries machines w/ AIX & Linux partitions

7311-D20

8203-E4A

8204-E8A

9111-520

9117-MMA

9119-FHA

9124-550/720

9405-520
9406-270/520/550/570/595/800/810/820/825/830/840/870/890
9411-100

 

* 2.3 AIX Requirements:*
For support:  AIX 5.2 TL_10 or AIX 5.3 TL_06

* 2.4 Linux Requirements:*
For support:

SUSE Linux Enterprise Server 9 Service Pack 2 for POWER or later
Red Hat Enterprise Linux AS for POWER Version 4 Update 2 or later

* 3.0 Determine the Current Microcode Level for AIX:*

Before you install the microcode, it is important to determine the
microcode level of the Adapter installed in the target system. Use

the following instructions to read the ROM level stored in the Adapter's
VPD.

1)  List the SCSI RAID Adapters installed in the system by typing:

    lsdev -C | grep sisioa

Note: All of the SCSI RAID initiators addresses that are installed will
be displayed. The names will be sisioaX, where X is 0, 1, etc.

2) To check the current microcode level for the adapter or controller
enter the following command

   lscfg -vl sisioaX

Where X is the number/s of the previous command. The Command will
produce output similar to

 

*     DEVICE       LOCATION         DESCRIPTION*

     sisioa0     UTMPB.BBH.BB002FA-P1-C03     PCI-XDDR Quad Channel U320
SCSI RAID Adapter

    PCI-XDDR Quad Channel Ultra320 SCSI RAID Adapter:
    Part Number.................97P6130
    FRU Number..................97P6130
    Serial Number...............YL3296005004
    Manufacture ID..............0029
    EC Level....................2
*    ROM Level.(alterable).......06150039*
    Product Specific.(Z0).......*571E*
    Product Specific.(Z1).......1
    Device Specific.(YL)........UTMPB.BBH.BB002FA-P1-C03
 

OR


    sisioa0     UTMPB.BBF.BB347AC-P1-C06     PCI-XDDR Quad Channel U320
SCSI RAID Adapter

    PCI-XDDR Quad Channel Ultra320 SCSI RAID Adapter:
    Part Number.................39J5909
    FRU Number..................42R4280
    Serial Number...............YL10C6075006
    Manufacture ID..............000C
    EC Level....................0
*    ROM Level.(alterable).......06150034*
    Product Specific.(Z0).......*571F*
    Product Specific.(Z1).......1
    Device Specific.(YL)........UTMPB.BBF.BB347AC-P1-C06

 

If the *ROM Level* is less than *0715002a* then you should update the
microcode.

* 3.1 Determine the Current Microcode Level for Linux:*

SLES 9 and RHEL 4:
1) Type "iprconfig"
2) Select "Display hardware status"
3) Select SCSI adapter by typing a "1" in front of it *(571E or 571F)*
and pressing Enter.
4) The Command will produce output similar to
*"Firmware Version . . . . . . . . . . . . : 06150039"*

If the *Firmware Version* is less than *0715002a* then you should update
the microcode.

*4.0 Downloading and Unpacking the Firmware Update Package from CORE*

NOTE:  The CORE image will now be the RPM Format File.

1) After downloading the files from CORE on to your personal system find
the following files in the CORE destination directory (c:\ibmdocs\DISKIMG):
    A) "pci.90050503.15-0715002a-1.aix5.1.noarch.rpm"
    B) "pci.90050503.15-0715002a-1.Linux.noarch.rpm"
2) Log in to the Target Server
3) Create a directory, if not already existent (mkdir /tmp/microcode;
mkdir /tmp/microcode/RPM)
4) Transfer the file to the Target Server "/tmp/microcode/RPM directory"
using ftp or another method.  Change to that directory, "cd
/tmp/microcode/RPM".
5a) For AIX:  Unpack the RPM file by using the following command:  "rpm
-ihv --ignoreos --force pci.90050503.15-0715002a-1.aix5.1.noarch.rpm"
5b) For Linux:  Unpack the RPM file by using the following command: 
"rpm -ihv --ignoreos --force pci.90050503.15-0715002a-1.Linux.noarch.rpm"
6a) For AIX:  The microcode files will be added to /usr/lib/microcode/.
6b) For Linux:  The microcode files will be added to /lib/firmware/.

*4.1 Downloading the RPM Format File to the Target Server*
Use this method to download to an AIX or Linux system:

*Note:* The instructions that follow are specific AIX/Linux commands.
AIX/Linux commands are CASE (lower and upper) SENSITIVE, and */must/* be
entered exactly as shown, including filenames.

1) Make a directory on an AIX/Linux system to receive the RPM format file.
    Enter:      "mkdir /tmp/microcode"

    Enter:      "mkdir /tmp/microcode/RPM"
2) Transfer the RPM format file to the /tmp/microcode/RPM directory
(using "Save as ...").  Change to that directory, "cd /tmp/microcode/RPM".

You'll see the filenames for the RPM files.
    A) For AIX, the filename is
*pci.90050503.15-0715002a-1.aix5.1.noarch.rpm
*    B) For Linux, the filename is
*pci.90050503.15-0715002a-1.Linux.noarch.rpm
*3) Unpack the file by executing the instructions below:
    A) For AIX, type "*rpm -ihv --ignoreos --force
pci.90050503.15-0715002a-1.aix5.1.noarch.rpm"
*    B) For Linux, type "*rpm -ihv --ignoreos --force
pci.90050503.15-0715002a-1.Linux.noarch.rpm"*
4a) For AIX:  The microcode files will be added to /usr/lib/microcode/.
4b) For Linux:  The microcode files will be added to /lib/firmware/.
 

* 4.2 Discovery Tool Microcode CD-ROM creation and download instructions*

To obtain information how to burn a CD-ROM and run the Discovery Tool
for an AIX System please go to:
http://techsupport.services.ibm.com/server/mdownload/CDROMhelp.html
1) After running the Discovery Tool successfully the
"/tmp/microcode/RPM" directory was created and your rpm files are copied
from the CD-ROM.

2) Change to that directory, "cd /tmp/microcode/RPM".

3) Unpack the file by executing the instructions below:
    Enter the commands:
        *rpm -ihv --ignoreos --force
pci.90050503.15-0715002a-1.aix5.1.noarch.rpm*
4) Microcode files will be copied to "/etc/microcode".  The file size
and checksum of the microcode image will be verified in Section 5.0

*Notes:*
 - "/etc/microcode" is a symbolic link to "/usr/lib/microcode".
 - If permission does not allow the copy to the above stated directory
                  or file then the user will be prompted for a new
location.

* 5.0 Verifying microcode before download and notes*

*NOTE:* Microcode download must be performed separately for each Adapter
bus under distinct Logical Partitions (LPAR's).
              Please save current and older versions of the microcode
update files in case you need to restore your system.

*NOTE:* Microcode Download CAN be performed concurrently.

/Installation Time:  /Approximately 30 min System Time.

Please verify the file size and checksum of the raw microcode files
matches the below.*
**Filesize:  1367892*
*Checksum:  61512*
For AIX:  "ls -l /usr/lib/microcode/53495315.0715002a" to verify Filesize. 
                "sum /usr/lib/microcode/53495315.0715002a" to verify
Checksum.
For Linux:  "ls -l /lib/firmware/pci.90050503.15.0715002a" to verify
Filesize.
                 "sum /lib/firmware/pci.90050503.15.0715002a" to verify
Checksum.

For systems that have LPAR installed, the microcode file must be placed
on all partitions that have a SCSI device in order to update the code. 
Follow this procedure for each partition:

For AIX:
    A)  Log into the target partition.
    B)  Type: "cd /usr/lib/microcode"
    C)  FTP (for AIX) or SFTP (for Linux) to the partition that has the
media bay assigned. (ie.  ftp/sftp partition1.ibm.com)
    D)  Type: "cd /usr/lib/microcode"
    E)  If using FTP then Type: "bin"
    F)  Type: "get 53495315.0715002a"
    G)  Type: "quit"

For Linux:
    A)  Log into the target partition.
    B)  Type: "cd /lib/firmware"
    C)  SFTP to the partition that has the media bay assigned. (ie. 
"sftp partition1.ibm.com")
    D)  Type: "cd /lib/firmware"
    E)  Type: "get pci.90050503.15.0715002a"
    F)  Type: "quit"

*5.1 Microcode Download Procedure-**PCI-XDDR Quad Channel U320 SCSI RAID
Adapter for AIX*

*/Procedure:/*
1) It is advised, but not necessary to stop all applications.
2) Enter diag
3) Select the "Task Selection" from diagnostics menu.
4) Select "Download Microcode" or "Microcode Tasks -> Download
Microcode" from "Task Selection" menu.
5) Select all of the PCI-XDDR Quad Channel U320 SCSI RAID Adapters that
need to be updated from the list of devices by pressing "Enter".  The
devices will be displayed as sisioa#, where # is the number of the
device.  Press "F7".
6) A dialogue box will be displayed on screen.  Press "Enter" to continue.
7) Select "/usr/lib/microcode".
8) A dialogue box will may be displayed on screen.  It will state that
the current microcode level on the adapter is not in the
/usr/lib/microcode directory.  This is acceptable as you will be
flashing new microcode onto the adapter.  Also, incorrect code will
automatically be rejected.  Press "Enter" to continue.
9) An "M" will be displayed next to the latest level of microcode in the
/usr/lib/microcode directory.  Select that level and press "Enter".
10) The following message will appear on the screen when download is
completed: "Microcode download complete successfully.  The current
microcode level for the device sisioa# is .....  Please run diagnostics
on the adapter to ensure that it is functioning properly."  DO NOT run
diagnostics on the device at this time.
11) Exit diagnostics.
12) Verify the code level is 0715002a by typing "lscfg -vl sisioai#" for
each scsi device updated. <Where # is the number sisioa device>

*5.2 Microcode Download Procedure-PCI-XDDR Quad Channel U320 SCSI RAID
Adapter for Linux*

*/Procedure:/*
1) Stop all applications.
2) Type "iprconfig" and press "Enter".
3) Select "Download Microcode" and press "Enter".
4) Select all of the PCI-XDDR Quad Channel U320 SCSI RAID Adapters that
need to be updated from the list of devices by pressing "1". Then press
"Enter".
5) Select the appropriate microcode image to flash by pressing "1". 
(The image will end in 0715002a).  Press Enter.  Press Enter again to
confirm.
6) If multiple devices were selected in step 4, then repeat step 5 until
finished.

 

* 6.0 Microcode Readme Change History*
 

2008-04-25 	

-Updated Section 2.2 Machine's Affected